Advertisement
O
REMOVE
EXISTING
DISPOSER
t. Turn O_t e lectrical power st fuse box or e=rcuitgrea_er.
2
DisCOnnectdrain trap from disposer waste discharge tube with adjustable pliers
(_ea Fig 6-1), (Also disconnect dlshwe=;har drain connection, t| required.)
3. _upport disposer w=thOneh=nd and insert =nOof wrench=tie cr screwdriver
into right side of one mounting lug on lower mounting ring (see Figure 6-2},
Lift disposer stightiy af_d loosen lower mounting ring _y pushing or pulling
wrench=tie or screwdriver to left until disposer is free from mounting assembly.
(Disposer m=y be heavy - provide support,)
4, With electrical supply turned off turn disposer upside down and remove eleotrt.
cal cover plate (sea Figure 6-3), Loosen green ground screw and remove
wire nuts (see Figure6-4), Disconnect disposerwlres from siectdoel auppiy
wire=, Loosen screw(s) on electrical cramp connector and remove wires from
disposer,
,.......,,.,
:
....
• II the new disposer mounting Is the same i_sOldor_e, remove mounting a=seml_y
from disposer (Instruction 3) and go to Ins!;ructlott 7,
. If the new disposer mounting is different from Ihe ol_ one (or you wish to repta_e
the old =Ink flange) you must compiate Steps 5- (] (below), snd Inatruottone
2.
5, then aontlrtue with Instruction
?,
5. Loosen three mourting sorews, pry snap ring eft with screwdriver, and r_move
oid mounting assembly (Jee Figure e,5), (Some mounting assembly removal
requires additional tOOlS,)
6. PuShold sink flange up throughsink hole (see Flour= 6,8), Use acrewdriver or
putty knife to scrape air Did putty from edge of Sinkhole.
CLEAN SINK DRAIN LINE
Fattureto clean sink drain tins may resutt in drain fine blockage.
t.
Remove P4rap,
2, Wl_hdrain auger, clear all h_rdened waste materiel in horizontal drain line.
tit
not
dtshwel_her te dO=poser,
to Imttructfon
9
t
d
you are
oorlnacting a
go
O
REPARE DISHWASHER
DRAIN CONNECTION
(IF
APPLICABLE)
The knockout drain plug shoutd only be removed il you are c_JnneCtir_g
a bu!lt-in dishwasher to the disposer. NOTE; ft the dishwa.',her
¢onnecflon i,_made without removing the #tuO the dishwasher may
ovedfOw, (Coltnedtig¢,s must comply wifh local plumbing ¢odes,)
Remove
Knockout
Plug
1. Lay disposer
on its side arid insert s_:rewdriver
into dishwasher
iMlet so tip rests
on outer edge of knockout
plug
2. Tap end of screwdriver handle
wkh h,ttmme_ unti4 me[dad
piug break'3 teose
(see Figure 8-t),
3. REMOVE
LOOSE KNOCKOUT
PLUG FROM
INSll3E
DISPOSEIq
Attach Dishwaahsr
Drain Connector
It your dtshwesi'ter
drain hose is 7/8" diameter,
g_, to Instruction
9.
If your dishwasher
drain hose is nol 718" diameter,
you must attach a distlwashor
drain cenRector
to the diehwa.sher drain Inlet Follow the iTtstallalion
IrlStrliCtions
wtlh the co,inaction
k_l. (You will c_nr_ecl the di_,hwa_her
drain hose to the
connector
in Inst_ctlort
123
3
6-2
i
ii
i
i
,,
8-3
8-4
8-S
8-8
Advertisement
