Advertisement
Table of Contents
FOOD WASTE
DISPOSERS
GUIDE FOR EASY, TROUBLE-FREE
INSTALLATION,
CARE AND USE.
HOW THIS GUIDE
WILL HELP YOU.
This guide describes everything you need to know
to install your new food waste disposer, including
care and use information.
If you take your time,
follow the instructions
and drawings,
you should
have no trouble making a first-rate installation.
NOTE: Read through the entire guide before you
start installation so you can get all the tools and
materials you will need with one trip to the store.
II lll_
!
These
are the tools
and
materials
you
will
need.
SCREWDRIVER
PLUMBER'S PUFFY
(¼ lb.)
ADJUSTABLE
("CRESCENT")
WRENCH
PIPE WRENCH
WIRE
NUTS
(2 -
Size 54)
WP71865
!1
These
are the tools
and
materials
you may need.
DRAIN
AUGER
HACK
SAW
HOSE
CLAMP
(7_ inch)
ONw'IOF F I_LECaTmR_
CrALng)_
HAMMER
ELECTRICAL
CABLE
CONNECTOR
(1/2 inch)
0
COPPER
WIRE
(12or14
gauge)
DISHWASHER
DRAIN CONNECTING
Advertisement
Table of Contents
Related Manuals for Kenmore 17560452 Guide
Summary of Contents for Kenmore 17560452 Guide
- Page 1 FOOD WASTE DISPOSERS GUIDE FOR EASY, TROUBLE-FREE INSTALLATION, CARE AND USE. HOW THIS GUIDE WILL HELP YOU. This guide describes everything you need to know have no trouble making a first-rate installation. to install your new food waste disposer, including NOTE: Read through the entire guide before you care and use information.
-
Page 2: Installation
INSTALLATION DIMENSIONS DISPOSER 175.6010 113/6" 6" 6%" 5" 4" 175.6012 11%" 6" 63/8" 5" 4" 175.6011 12%" 6" 63/8" 5" 4" B" 175.6013 125/6" 6" 63/e ' 5" 4" 175.6035 123/," 63/," 71/," 5" 4" NOTE: Please refer to the E"... - Page 3 The cutting elements on your old disposer were probably worn and not grinding the waste completely. Your drain line may be partially blocked, We recommend cleaning the line before connecting your new Kenmore disposer. Before routing You can do the job yourself with a drain auger. Remove the drain trap and, using the auger, clean out the horizontal drain pipe that runs from the trap to the main waste pipe.
- Page 4 HERE IS WHAT TO DO IF YOU ARE ENSION TUBE INSTALLING YOUR SINK'S FIRST DISPOSER. Next, remove the nut at the top of Use a pipe wrench to loosen the the sink strainer and remove nut at the top of the drain trap. extension tube.
- Page 5 ET'S KEEP GOING...IT'S GETTING EASIER, WE HOPE. NOW WE'RE GETrlNG INTO APPLY PUTTY TO THE THE ACTUAL INSTALLATION. SINK SLEEVE. SEPARATE THE PARTS IN THE MOUNTING ASSEMBLY. Lower Screw Wrenchette Then loosen the screws on the moun- First, remove the mounting assembly Make a fat snake of "plumber's"...
- Page 6 I I II 11 WE'RE READY TO MAKE THE ELECTRICAL CONNECTIONS. NOTE: If using armored cable, we recommend installing an anti-short or insulation bushing in the end of the cable. Do not fold or remove Now, tighten the connector brown electrical insulation clamp...
- Page 7 NEXT, MAKE SURE THE DISPOSER IS GROUNDED. If the cable leading to the disposer does not have Green ground wire, use a copper .,_.J Green Ground wire that is no smaller than the Ground Screw other wire in your cable. At- tach one end of the wire to the disposer has three wires, at- green ground screw on the...
-
Page 8: Drain Connection
NOW, ATTACH THE DISPOSER DISCHARGE TUBE TO YOUR SINK'S DRAIN TRAP. First, check inside Turn the disposer around to attach the discharge tube. In D. install the discharge tube gasket onto Some models use a rubber washer that must be assem- disposer grinding cham-... -
Page 9: Do's And Don'ts
DISPOSER IN LEAKS PLACE. NOW, LOCK THE CHECK FOR Place the end of your "wren- chette" or a screwdriver into the left side of one of the mounting ring lugs at the top of the disposer. Then, turn the "wren- chette"... -
Page 10: User Maintenance
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS. IMPORTANT SAFETY INSTRUCTIONS obiects do not enter the arind chamber that may conductor and a grounding plug, the plug must be exuelled. Reolace the anti-splash baffle when WARNING: When using...