On Screen Messages - Panasonic TXL42D25 Operating Instructions Manual

On screen messages

Message
All contents will be lost.
Are you sure to delete this device?
All tuning data will be erased
Are you sure ?
Are you sure you want to delete this timer ?
Press OK to delete timer.
Press RETURN to return.
Bad signal
Cannot register another device because
the list is full.
Child Lock is active!
Press OK to enter PIN.
Faulty dish
Feature not available.
Feature not available.
Press OK to view how it works.
Found new software version
Press OK to start update (may take
40 mins) or Press EXIT to ignore
and you can update when TV is in standby
Invalid operation - Please check settings
and connections.
Invalid system time. Please exit !
Invalid system time, Timer Programming
will not work.
Please press TV button on remote control
and check time display on Banner
Max. number of timers already set !
New channels found!
Press OK to update channel list.
Press EXIT to ignore.
No channel found.
Please check aerial or local signal availability.
Press OK to start Auto Setup.
No module inserted
No recording - Already recording
No recording - Check media
No recording - Playing
No recording - Unknown reason
No service
No signal
Overcurrent error on USB device occurred.
Please remove the USB device, and switch
off the TV by mains power switch.
102
●
Once you unregister the USB HDD, all the recorded programme will be
erased.
●
"Shipping Condition" will erase all tuning data (p. 51).
●
Confirm correct operation.
●
Confirm correct operation.
●
The signal is weak. Check the aerial is plugged in properly. It may be
necessary to have an aerial installer check the signal and aerial alignment.
●
Reset channels. (p. 40 and p. 41)
●
Up to 8 USB HDDs can be registered with this TV.
●
The selected channel is locked in Child Lock (p. 54). You must enter the
PIN number before the channel will be displayed.
●
The satellite cable might be short-circuited or there might be connection
problems of the cable. Check the cable and connection and then turn the
TV Off with the Mains power On / Off switch, and turn it On again.
●
If the message still persists, it may be necessary to have a dish installer
check the dish and cable.
●
It is not possible to record from COMPONENT or HDMI. Connect the
recorder to the TV using a fully wired SCART cable for recording from the
TV tuner.
●
Confirm Q-Link or VIERA Link settings (p. 84 - 87).
●
The selected feature on VIERA TOOLS is not available. Press the OK
button to view the demonstration to explain how to use it.
∗∗∗
.
●
There is a new software available.
●
Check the Q-Link or VIERA Link connection and setting (p. 84 - 87).
●
Cannot get the time information and cannot edit Timer Programming
screen. Check the connection of the RF cable.
●
Cannot get the time information. If there is no time displayed on the
Information banner, check the connection of the RF cable.
●
The maximum number of timer programming events is 15.
●
There may be new channels available.
●
This message will appear each time a change is made by the
broadcasters. This message can be deactivated by setting "New Channel
Message" to Off in "DVB Tuning Menu".
Selecting OK will perform "Update Channel List".
●
Follow the on screen instructions.
●
Please also refer to p. 99.
●
If channels are still not found, consult your local Panasonic dealer.
●
Check the CI module is inserted completely (p. 57).
●
The equipment may already be recording.
●
The tape or disc may be "write protected", full, missing or damaged.
●
The equipment may be playing the tape or disc.
●
The recording may not be performed. Check the equipment.
●
The broadcaster has stopped the service. Check the channel in the TV
Guide. (p. 20)
●
The TV cannot detect the signal. Check the connection of the RF cable.
●
The connected USB device might cause overcurrent error. Follow the on
screen instructions.
●
Check if foreign objects are inside the USB port.
Meaning / Action