Brother LK3-B434E MKII Instruction Manual
  1. Manuals
  2. Brands
  3. Brother Manuals
  4. Sewing Machine
  5. LK3-B434E
  6. Instruction manual
Brother LK3-B434E MKII Instruction Manual

Brother LK3-B434E MKII Instruction Manual

Electronic lockstitch pattern tacker
Hide thumbs Also See for LK3-B434E MKII:
Table of Contents

Advertisement

Quick Links

LK3-B434E
INSTRUCTION MANUAL
Please read this manual before using the machine.
Please keep this manual within easy reach for quick reference.
ELECTRONIC LOCKSTITCH PATTERN TACKER

Advertisement

Table of Contents
loading

Related Manuals for Brother LK3-B434E MKII

Summary of Contents for Brother LK3-B434E MKII

  • Page 1 LK3-B434E INSTRUCTION MANUAL Please read this manual before using the machine. Please keep this manual within easy reach for quick reference. ELECTRONIC LOCKSTITCH PATTERN TACKER...

  • Page 2: Safety Instructions

    Thank you very much for buying a BROTHER sewing machine. Before using your new machine, please read the safety instruc- tions below and the explanations given in the instruction manual. With industrial sewing machines, it is normal to carry out work while positioned directly in front of moving parts such as the needle and thread take-up lever, and consequently there is always a danger of injury that can be caused by these parts.
  • Page 3 2. Notes on safety DANGER Wait at least 5 minutes after turning off the power switch and disconnecting the power cord from the wall outlet before opening the face plate of the control box. Touching areas where high voltages are present can result in severe injury. CAUTION Environmental requirements The ambient temperature should be within the range...
  • Page 4 CAUTION Sewing This sewing machine should only be used by opera- If using a work table which has casters, the casters tors who have received the necessary training in safe should be secured in such a way so that they cannot use beforehand.

  • Page 5: Warning Labels

    3. Warning labels The following warning labels appear on the sewing machine. Please follow the instructions on the labels at all times when using the machine. If the labels have been removed or are difficult to read, please contact your nearest Brother dealer. Hazardous voltage Hochspannung Un voltage non adapté...

  • Page 6: Table Of Contents

    CONTENTS 9-2. Lubrication ..........33 1. NAME OF EACH PART ....... 01 9-3. Draining the oil ........34 2. SPECIFICATIONS ......... 02 9-4. Cleaning the control box air inlet port ............34 2-1. Specifications ........2 9-5. Cleaning the eye guard ....... 34 2-2.

  • Page 7: Name Of Each Part

    1. NAME OF EACH PART 1. NAME OF EACH PART Specifications with inner clamping device [LK3-B434E Mark II/Solenoid specifications] [LK3-B434E Mark II/Pneumatic specifications] Safety devices; q Power switch ! 2 Finger guard w Control box !3 Eye guard e Operation panel !4 Thread take-up cover r Foot switch !5 Belt cover...

  • Page 8: Specifications

    2. SPECIFICATIONS 2. SPECIFICATIONS 2-1. Specifications BROTHER INDUSTRIES, LTD. Medium materials LK3-B434EX-3 Heavy materials MADE IN JAPAN Stitch formation Single needle lock stitch Maximum sewing speed 2,500 rpm (Pitch 3 mm) Maximum pattern size 60 mm max. Feed mechanism R- intermittent feed mechanism (pulse-motor driven mechanism) Stitch length 0.1 - 10.0 mm Number of stitches...

  • Page 9: Examples Of Sewing Patterns

    2. SPECIFICATIONS 2-2. Examples of sewing patterns The following are examples of possible patterns with the LK3-B434E Mark II. Sewing patterns Uses Decorative tacking Triangular chain tacking Rectangular decorative tacking Number of stitches Sewing patterns Uses Cross tacking Open cross tacking Buckle stitching Number of stitches Sewing...

  • Page 10: Installation

    3. INSTALLATION 3. INSTALLATION CAUTION Machine installation should only be carried All cords should be secured at least 25 mm out by a qualified technician. away from any moving parts. Furthermore, do not excessively bend the cable or se- Contact your Brother dealer or a qualified cure it too firmly staples, otherwise there is electrician for any electrical work that may the danger that fire or electric shocks could...

  • Page 11: Installing The Motor

    3. INSTALLATION 3-2. Installing the motor Install the motor u to the work table with the four ac- cessory bolts q, cushions w, cushion collars e, flat washers r, spring washers t and nuts y. At that time, fix by setting bolts q a little to the right of oval hole on motor.

  • Page 12: Installing The Control Box

    3. INSTALLATION 3-4. Installing the control box Table Cushions Cushion collars 3 mm Rubber collers Flat washers Nuts 1. Remove the 12 screws q, and then open the covers (panel mounting assembly w and main P.C. board mounting plate e). NOTE: When opening the cover, hold it securely so that it does not fall down.

  • Page 13: Installing The Rubber Cushions

    3. INSTALLATION 3-5. Installing the rubber cushions Install the rubber cushions q with the nails w. 3-6. Installing the oil pan 1. Insert the tabs of the oil pan w into the holes for the cushions q, and then secure it in place with the five nails e so that the oil pan w is not at an angle.

  • Page 14: Installing The Machine Head

    3. INSTALLATION 3-8. Installing the machine head 1. Insert the head hinges q into the machine head so that they are parallel, and then secure them with the two set screws w. 2. Place the machine head gently on top of the rubber cushions e and cushions r. NOTE: Pull the cords t out as shown in the illustration above in order to prevent them from being clamped by the machine head.

  • Page 15: Installing The Operation Panel

    3. INSTALLATION 3-11. Installing the operation panel The operation panel can be installed to either the top or bottom of the work table. Top of work table Bottom of work table Table Table 1. Install the rear frame q to the work table (top or bottom) with the four wood screws w. 2.

  • Page 16: Connecting The Cords

    3. INSTALLATION 3-13. Connecting the cords 1. Gently tilt back the machine head. NOTE: After tilting back the machine head, do not push the face side or the pulley side from above. 2. Pass the cords q through the hole w in the work table. 3.
  • Page 17 3. INSTALLATION 90˚ 90˚ R E S E T 11. Replace PROM control assembly with one which contains sewing data. 1) Use the special tool to remove the PROM control assembly !4 from the PROM socket !5 . * Store the removed PROM control assembly in the special case provided. 2) Bend the pins of the PROM control assembly which contains sewing data ! 6 so that they are at an angle of approximately 90˚.

  • Page 18: Piping (For Pneumatic)

    3. INSTALLATION 3-14. Piping (for pneumatic) Pneumatic work clamp Upper knob Lower knob Switch Cylinder R Cylinder L Reversal Reverse work clamp cylinder Connect air tubes in accordance with the identified numbers in the figure. At this time, pass the air tubes through the hole q and then pass it through the work table hole.
  • Page 19 3. INSTALLATION 3-14-1. Installing the air unit Make sure that the air unit does not touch the control box or the work table leg. 50 mm 120 mm When installing to the underside of the work table 1. Remove the two screws q and the valve setting plate w. 2.

  • Page 20: Installing The V-Belt

    3. INSTALLATION 3-15. Installing the V-belt 1. Gently tilt back the machine head, and then place the V-belt q into the V grooves on the machine head pulley w and the motor pulley e. NOTE: After tilting back the machine head, do not push the face plate side or the pulley side from above.

  • Page 21: Installing The Belt Cover

    3. INSTALLATION 3-16. Installing the belt cover 1. Loosen the two screws w of the upper cover q and the two screws r of bed cover Le. 2. Insert the belt cover t in the direction of the arrow, and then secure it with the two screws w, the two screws r and the screw y.

  • Page 22: Installing The Motor Cover

    3. INSTALLATION 3-18. Installing the motor cover 1. Install the motor cover q to the motor back cover w with the screws e and the flat washers r. 2. Pass the motor shaft through the notch in the mo- tor back cover w, and then tighten the screws y and the washers u so that the clearance between the motor pulley t and the motor cover q is uniform.

  • Page 23: Installing The Needle Sub Plate

    3. INSTALLATION 3-20. Installing the needle sub plate 1. Install the four needle sub plate supports q with the four screws w. 2. Insert the needle sub plate e from the front of the machine so that it is level. NOTE: Insert the needle sub plate e so that the X feed lever cap r sits on top of the needle sub plate e.

  • Page 24: Installing The Eye Guard

    3. INSTALLATION 3-21. Installing the eye guard CAUTION Attach all safety devices before using the sewing machine. If the machine is used without these devices attached, injury may result. Install the eye guard assy w to the face plate q with the two screws e.

  • Page 25: Lubrication

    4. LUBRICATION 4. LUBRICATION CAUTION Turn off the power switch before starting lubricating, otherwise the machine may operate if the foot switch is depressed by mistake, which could result in injury. Be sure to wear protective goggles and gloves when handling the lubricating oil and grease, so that they do not get into your eyes or onto your skin, otherwise inflammation can result.

  • Page 26: Operation

    5. OPERATION 5. OPERATION 5-1. Name and function of each operation panel item B430E Series PROGRAM NO. POWER X - SCALE R E S E T Y - SCALE SPEED T E S T COUNTER S E L E C T BOBBIN.WIND q POWER indicator ....
  • Page 27 5. OPERATION B430E Series PROGRAM NO. POWER X - SCALE R E S E T Y - SCALE SPEED T E S T COUNTER S E L E C T BOBBIN.WIND i X-SCALE indicator ....Illuminates when the SELECT switch y is pressed to shown the X-scale set- ting.

  • Page 28: Operating Procedure

    5. OPERATION 5-2. Operating procedure Preparation Factory default Variable range Turn on the power switch. Program No. 100 - * (The POWER indicator q will illuminate and the pro- gram number will flash in the display window !4 . ) X-scale (%) 20 - 200 Y-scale (%)

  • Page 29: Operating The Foot Switch

    5. OPERATION 5-3. Operating the foot switch Single-pedal foot switch (two steps) When the foot switch is depressed to step 1, the work clamp is lowered, and when it is depressed to step 2, sewing starts. 1st step 2nd step Two-pedal foot switch (one step + one step) When the work clamp switch (left side) is depressed, the work clamp is lowered, and when the start switch...

  • Page 30: Operating The Emergency Stop Switch

    5. OPERATION 5-4. Operating the emergency stop switch If the emergency stop switch is pressed while normal sewing or test sewing is being carried out, the sewing machine will immediately stop operating. Canceling an emergency stop 1. Turn the emergency stop switch q clockwise and then pull it out to release the lock.

  • Page 31: Checking The Sewing Pattern

    6. CHECKING THE SEWING PATTERN 6. CHECKING THE SEWING PATTERN When checking by operating only the feed mechanism 1. Turn on the power switch. (The POWER indicator will illuminate and the program number will flash in the display window.) 2. Press the TEST switch. (The TEST indicator will illuminate.) T E S T 3.

  • Page 32: Correct Use

    7. CORRECT USE 7. CORRECT USE 7-1. Selecting the needle and thread Needle Thread Main application Different needles and threads are used for different 5 #14 #80 - #50 Medium materials sewing applications. 17NY #19 #50 - #20 Heavy materials Refer to the table at right for details on which needle and thread to select.

  • Page 33: Winding The Lower Thread

    7. CORRECT USE 7-4. Winding the lower thread CAUTION Do not touch or place anything against any of the moving parts while winding the lower thread, otherwise personal injury or damage to the machine may result. 1. Place the bobbin all the way onto the shaft. 2.

  • Page 34: Replacing The Bobbin Case And Threading The Thread

    7. CORRECT USE 7-5. Replacing the bobbin case and threading the thread CAUTION Turn off the power switch before removing and replacing the bobbin case, otherwise the machine may operate if the foot switch is depressed by mistake and serious injury could result. 30 mm Pull the shuttle race cover q toward Insert a new bobbin into the bobbin...
  • Page 35 7. CORRECT USE 7-6-1. Guide to maximum sewing speed <Standard hook> NOTE: Max. sewing speed (rpm) The thread may break due to heat under some sewing conditions. If this happens, reduce the sewing speed, or 8 layers of denim 2,500 use the liquid cooling tank (option).
  • Page 36 7. CORRECT USE 7-6-4. Thread take-up spring height 7-6-5. Thread take-up spring tension Lower Higher Stronger Weaker Loosen the set screw q and turn the tensioner body Turn the tension stud q with a s c rewd r iver. to adjust the thread take-up spring height. 7-6-6.

  • Page 37: Sewing

    8. SEWING 8. SEWING CAUTION Turn off the power switch at the following times, otherwise the machine may operate if the foot switch is depressed by mistake, which could result in injury. • Threading • When replacing the needle • When not using the machine and when leaving the machine unattended. Do not touch any of the moving parts or press any objects against the machine while sewing, as this may result in personal injury or damage to the machine.

  • Page 38: Maintenance And Inspection

    9. MAINTENANCE AND INSPECTION 9. MAINTENANCE AND INSPECTION CAUTION Turn off the power switch before carrying out cleaning, otherwise the machine may operate if the foot switch is pressed by mistake, which could result in injury. Be sure to wear protective goggles and gloves when handling the lubricating oil and grease, so that they do not get into your eyes or onto your skin, otherwise inflammation can result.

  • Page 39: Lubrication

    9. MAINTENANCE AND INSPECTION 9-2. Lubrication NOTE1: Fill the machine with oil when the oil level is down to about one-third full in the oil sight glass. If oil is not added and the oil drops below this level, there is the danger that the machine may seize during operation.

  • Page 40: Draining The Oil

    9. MAINTENANCE AND INSPECTION 9-3. Draining the oil 1. Remove and empty the waste oil container q whenever it is full. 2. After emptying the waste oil container q, screw it back into its original position. 9-4. Cleaning the control box air inlet port Use a vacuum cleaner to clean the filter in the air inlet port w of the control box q at least once a month.

  • Page 41: Standard Adjustments

    10. STANDARD ADJUSTMENTS 10. STANDARD ADJUSTMENTS CAUTION Maintenance and inspection of the sewing Hold the machine head with both hands machine should only be carried out by a quali- when tilting it back or returning it to its origi- fied technician. nal position.

  • Page 42: Adjusting The Driver Needle Guard

    10. STANDARD ADJUSTMENTS 10-3. Adjusting the driver needle guard Needle center line Turn the machine pulley to align the tip of the rotary hook with the needle center line. Then loosen the set screw w and turn the eccentric shaft e to adjust so that the driver needle guard q contacts the needle. If the needle contact pressure is too great, skipped stitches may occur.

  • Page 43: Adjusting The Thread Take-Up Amount

    10. STANDARD ADJUSTMENTS 10-6. Adjusting the thread take-up amount Thread take-up amount (stroke) Become less Become greater At the time of shipment from the factory, the thread take-up amount (stroke) of the thread take-up lever q is set to the standard setting of 5 mm. You may need to adjust this setting depending on the sewing conditions to prevent the thread from pulling out at the sewing start.
  • Page 44 10. STANDARD ADJUSTMENTS 10-7-1. Replacing the movable knife and fixed knife 1. Open the large shuttle hook cover, remove the bolts q and the feed plate w. 2. Remove the two screws e and the two screws r, and then remove the needle plate t. 3.
  • Page 45 10. STANDARD ADJUSTMENTS 10-7-2. Adjusting the engagement of the movable knife and fixed knife Fig. 1 Movable knife Cutting Fix knife edge Cutting edge Cutting edge Cutting edge A. After the movable knife and fixed knife are properly engaged, tighten the screw as shown in Fig.1. B.

  • Page 46: Adjusting The Work Clamp Lift Amount

    10. STANDARD ADJUSTMENTS 10-8. Adjusting the work clamp lift amount The maximum work clamp lift amount is 17 mm (25 Medium Heavy Uses mm for pneumatic, 17 mm for machines with inner materials materials clamping device) from the top of the needle plate. Lift amount The lift amount is adjusted as shown in the table at the time of shipment.

  • Page 47: Work Clamp Interchangeability

    10. STANDARD ADJUSTMENTS 10-9. Work clamp interchangeability The BAS-311E work clamp can also be used with the B434E Mark ll. Replace the feed bar guide cover q with the feed bar guide cover assembly, LL w (optional). Then, change the installation position for the presser arm assembly e from the standard installation posi- tion A to installation position B.

  • Page 48: 10-11.Adjusting The Thread Wiper

    10. STANDARD ADJUSTMENTS 10-11. Adjusting the thread wiper [Solenoid type] 0.5 mm Approx. 20 mm 1. Loosen the set screw w and move the wiper arm support e up or down to adjust so that the clearance between the top of the thread wiper and the needle point q is 2 0.5 mm when the thread wiper is aligned with the center of the needle.

  • Page 49: 10-12.Checking The Input Sensor And Dip Switch Input

    10. STANDARD ADJUSTMENTS 10-12. Checking the input sensor and DIP switch input B430E Series PROGRAM NO. POWER X - SCALE R E S E T Y - SCALE SPEED T E S T COUNTER BOBBIN.WIND S E L E C T 1.

  • Page 50: 10-13.Checking The Input Voltage

    10. STANDARD ADJUSTMENTS 10-13. Checking the input voltage B430E Series PROGRAM NO. POWER X - SCALE R E S E T Y - SCALE SPEED T E S T COUNTER BOBBIN.WIND S E L E C T Specifications Display Notes 200V [090 - 110] 220V...

  • Page 51: 10-15.Moving Stitch Patterns

    10. STANDARD ADJUSTMENTS 10-15. Moving stitch patterns • Programs which have already been programmed can be moved up, down and to the left and right. (How- ever, such patterns will be reset if the power supply is turned off or the program number is changed.) •...

  • Page 52: 10-16.Adjustment Of Air Pressure (For Pneumatic)

    10. STANDARD ADJUSTMENTS 10-16. Adjustment of air pressure (for pneumatic) 1. Air pressure should be 0.5 Mpa. Increase pressure The air pressure can be adjusted by pulling up and turning the control knob w on the integrator q. After adjustment is complete, push the control Increase pressure knob w downward to lock it.

  • Page 53: Using The Counters

    11. USING THE COUNTERS 11. USING THE COUNTERS 11-1. Using the bobbin thread counter If you use the bobbin thread counter to set the number of articles which can be sewn with the amount of bobbin thread available, you can stop the bobbin thread running out in the middle of sewing a pattern. 1.

  • Page 54: Changing Functions Using The Dip Switches

    12. CHANGING FUNCTIONS USING THE DIP SWITCHES 12. CHANGING FUNCTIONS USING THE DIP SWITCHES 12-1. Operation panel DIP switches The functions shown in the table below can be changed by means of these DIP switches q. * All DIP switches are set to OFF at the time of ship- ment.

  • Page 55: Dip Switches Inside The Control Box

    12. CHANGING FUNCTIONS USING THE DIP SWITCHES 12-2. DIP switches inside the control box DANGER Wait at least 5 minutes after turning off the power switch and disconnecting the power cord from the wall outlet before opening the face plate of the control box. Touching areas where high volt- ages are present can result in severe injury.

  • Page 56: Using User Programs

    12. CHANGING FUNCTIONS USING THE DIP SWITCHES 12-3. Using user programs User program ... It can store sixteen different programs which can include details such as the program number, X scale, Y scale and sewing speed. If you are sewing certain patterns over and over again, it is useful to record the settings for these patterns into a user program.
  • Page 57 12. CHANGING FUNCTIONS USING THE DIP SWITCHES Using a user program 1. Press the DISPLAY SET switches !0 to select the speed program number for the user program that you would like to use. *The user program numbers P1 to P4 can also be selected using the user program switches !1 . 2.

  • Page 58: Changing Special Functions Using The Memory Switches

    13. CHANGING SPECIAL FUNCTIONS USING THE MEMORY SWITCHES 13. CHANGING SPECIAL FUNCTIONS USING THE MEMORY SWITCHES The functions of the switches on the operation panel q can be changed to carry out special functions. NOTE: After changing the memory switch settings, press the power switch to turn the power off and then back on again. 1.
  • Page 59 13. CHANGING SPECIAL FUNCTIONS USING THE MEMORY SWITCHES Memory switches 10 - 1F Initial value Switch Motion when set to ON Solenoid Pneumatic memo-10 – memo-11 Pneumatic wiper can be used. (Pneumatic wiper is available by special memo-12 order.) The inner clamping device moves forward at the 1/4-way mark and returns memo-13 at the 3/4-way mark for the pattern being sewn.
  • Page 60 13. CHANGING SPECIAL FUNCTIONS USING THE MEMORY SWITCHES Memory switches 30 - 4F 30 to 4F are set by entering two-digit values. These values are incremented using the P2 switch, and decremented using the P4 switch. Switch Possible setting range Units Initial value Explanation...

  • Page 61: Using The Cycle Sewing Function

    13. CHANGING SPECIAL FUNCTIONS USING THE MEMORY SWITCHES 13-1. Using the cycle sewing function What is the cycle sewing function? The cycle sewing function lets you program up to four patterns for cycle sewing of patterns in a predeter mined order. Recording a cycle sewing program 1.
  • Page 62 13. CHANGING SPECIAL FUNCTIONS USING THE MEMORY SWITCHES Using a cycle sewing program 1. When “c1-1” is flashing in the display window !0 , press the foot switch to the second step. 2. Start sewing. 3. “c1-1”, “c1-2”, “c1-3” are sewn in order for each article, and when the last-recorded pattern has been sewn, the display returns to “c1-1".

  • Page 63: Setting The Work Clamp Mode

    14. SETTING THE WORK CLAMP MODE 14. SETTING THE WORK CLAMP MODE 14-1. Setting solenoid work clamp mode Through the combination of DIP switches A-1 and A-2 on the operation panel, presser motions can be set as follows: DIPA-1 DIPA-2 Pedal specifications Raising the presser at the sewing end –...

  • Page 64: Light Work Clamp

    14. SETTING THE WORK CLAMP MODE 14-3. Light work clamp For pneumatic specifications, the hose connections can be changed so that the pressers are made to lower gently when the presser pedal is depressed to the 1st step, and firmly when the presser pedal is depressed to the 2nd step.

  • Page 65: Setting Reverse Work Clamp Mode

    14. SETTING THE WORK CLAMP MODE 14-4. Setting reverse work clamp mode Basic setting 1. If installing the inner clamping device as a later option, set the memory switches as follows. (This will complete inner clamping specification settings.) • Set the memo-07 switch to ON. •...

  • Page 66: Table Of Error Codes

    15. TABLE OF ERROR CODES 15. TABLE OF ERROR CODES DANGER Wait at least 5 minutes after turning off the power switch and disconnecting the power cord from the wall outlet before opening the face plate of the control box. Touching areas where high volt- ages are present can result in severe injury.
  • Page 67 15. TABLE OF ERROR CODES Code Cause Remedy E-80 Motor PROM is not correctly inserted. Turn off the power and check. Foot switch was depressed when the E-81 Turn off the power and check. power was turned on. An operation panel switch was depressed Turn off the power and check the operation panel.

  • Page 68: Gauge Parts List According To Subclasses

    16. GAUGE PARTS LIST ACCORDING TO SUBCLASSES 16. GAUGE PARTS LIST ACCORDING TO SUBCLASSES The following are standard gauge parts according to each specification. (In the following table, parts marked with are common with the LK3-B430E; parts with are common with the BAS-311E.) With inner clamping Extra heavy...
  • Page 69 16. GAUGE PARTS LIST ACCORDING TO SUBCLASSES With inner clamping Extra heavy Specification Medium materials Heavy materials Part name device materials Thread guide, needle S41222-101 B 152890-001 A S41222-101 B S02439-001 B Needle assy 107415-414 S37928-419 145646-414 145646-425 Needle 5 #14 17 NY #19 17 #14 17 #25...
  • Page 70 16. GAUGE PARTS LIST ACCORDING TO SUBCLASSES 156082-001 (L) 156088-001 (S) 156083-001 (L) 156089-001 (S) Work clamp 156084-001 (L) 156090-001 (S) Feed plate • Gauge assy, 434E MK2 S54984-001 Home position standard plate • Needle hole plate S10211-001 S51449-001 S41013-001 S29997-001 S10212-101 S30925-001...

  • Page 71: Troubleshooting

    17. TROUBLESHOOTING 17. TROUBLESHOOTING Problem Cause Check Remedy Page Sliding part of the Grease the sliging Work clamp work clamp part of the work operation is sluggish. lubrication clamp. Distance between Adjust the height of Work clamp lift work clamp and top the work clamp to amount is too great.
  • Page 72 17. TROUBLESHOOTING Problem Cause Check Remedy Page Upper thread tension Adjust the upper Upper thread tension is too strong. thread tension. Install the needle so Needle is installed Needle direction that the groove is incorrectly. facing forward. Thread is too thick for Use the correct Thread and needle the needle.
  • Page 73 17. TROUBLESHOOTING Problem Cause Check Remedy Page Sharpen or replace Fixed knife is blunt. Fixed knife blade the fixed knife. Adjust the position of Shuttle race thread the shuttle race guide position Movable knife does thread guide. not pick up the thread.

  • Page 74: Optional Parts

    18. OPTIONAL PARTS 18. OPTIONAL PARTS Two-pedal foot switch ........The presser switch and the start switch have been separated, giving the operator more flexibility to select the best method of working. Two-step foot switch ......... This is a pedal-type foot switch. Liquid cooling tank ..........

  • Page 75: Instruction Manual

    INSTRUCTION MANUAL BROTHER INDUSTRIES, LTD. 15-1, Naeshiro-cho, Mizuho-ku, Nagoya 467-8561, Japan. Phone: 81-52-824-2177 Printed in Japan 118-V34 S91V34-002 2000.06. B (1)

This manual is also suitable for:

Lk3-b434e mark ii

Table of Contents