Audio Setup
You can flexibly customize the unit to suit your own preference and
usage. From the AUDIO SETUP menu, Audio Setting can be modified.
Use steps 1 to 5 to select one of the setting modes to modify.
See the applicable section below for details about the
selected setting item.
1
Press and hold AUDIOSETUP for at least 2 seconds to
activate the SETUP mode.
2
Turn the Rotary encoder to select AUDIO, and then press
ENTER.
AUDIO GENERAL DISPLAY TUNER iPod
3
Turn the Rotary encoder to select the desired sound
setting menu, and then press ENTER.
(e.g. Select SUBWOOFER)
*1/*2
LOUDNESS
FACTORY EQ
*1
HPF
SUBWOOFER SUBW LPF
*4
POWER IC
SUBW SYS
*1 Adjustment cannot be performed when DEFEAT is set to ON.
*2 The FACTORY EQ's setting value and 3BAND EQ's setting
value are linkage.
*3 The FACTORY EQ's setting value and 3BAND EQ's setting
value are linkage. In step 3, three sound adjustment items (Bass,
Mid and Treble) can be selected in 3BAND EQ mode, turn the
Rotary encoder to select the desired item, and then press
ENTER to continue to step 4.
*4 These functions are inoperable when Subwoofer is set to OFF.
4
Turn the Rotary encoder to change the setting, and then
press ENTER.
(e.g. Select SUBW ON or SUBW OFF)
5
Press and hold AUDIOSETUP for at least 2 seconds to
return to normal mode.
Notes
• Pressing returns to the previous Sound menu mode.
• Pressing and holding for at least 2 seconds will return to normal
mode.
• If no operation is performed for 60 seconds, Sound menu mode is
canceled.
Equalizer Presets (F-EQ)
10 typical equalizer settings are preset at the factory for a variety of
musical source material.
Setting item: FACTORY EQ
Setting contents:
USER / FLAT (Initial setting) / POPS / ROCK / NEWS / JAZZ /
ELEC DANCE / HIP HOP / EASY LIS / COUNTRY / CLASSICAL
*1
*1/*3
3BAND EQ
VOL LV ADJ
*4
*4
SUBW PHASE
Turning Loudness On/Off
Loudness introduces a special low-and high-frequency emphasis at low
listening levels. This compensates for the ear's decreased sensitivity to
bass and treble sound.
Setting item: LOUDNESS
Setting contents:
OFF (Initial setting) / ON
Adjusting the Parametric Equalizer Curve
(3BAND EQ)
You can modify the Equalizer settings to create a response curve more
appealing to your personal taste. The setting of Bass, Mid and Treble can
be adjusted in this mode.
Setting item: 3BAND EQ
Further setting items: BASS / MID / TREBLE
Setting the Bass Control
1
After selecting BASS from the 3BAND EQ adjustment
mode, turn the Rotary encoder to select the desired item,
and then press ENTER.
WIDTH (Q) CENTER FRQ LEVEL
2
Turn the Rotary encoder to select the desired setting
value, and then press ENTER.
3
Press to return to the previous step.
Setting the Bass Bandwidth (WIDTH (Q))
Turn the Rotary encoder to select the desired bass
bandwidth.
WIDE 0.50 MEDIUM 1.00 MEDIUM 1.50 NARROW 2.00
Change the boosted bass bandwidth to wide or narrow. A wider setting
will boost a wide range of frequencies above and below the center
frequency. A narrower setting will boost only frequencies near the
center frequency.
Setting the Bass Center Frequency (CENTER FRQ)
Turn the Rotary encoder to select the desired bass center
frequency.
60 (Hz) 80 (Hz) 100 (Hz) 120 (Hz)
Emphasize the displayed bass frequency ranges.
15
-EN