Page of 6

HP Z600 - Workstation - 6 GB RAM Installation Manual

Broadcom netxtreme gigabit ethernet plus network interface card installation.
Hide thumbs
   
Broadcom NetXtreme Gigabit Ethernet
Plus Network Interface Card installation
Introduction
This document describes how to install a Broadcom NetXtreme Gigabit Ethernet Plus Network
Interface Card (NIC) into a PCI Express (PCIe) slot on your computer.
Broadcom NetXtreme Gigabit Ethernet Plus NIC
USB cable
Broadcom NetXtreme driver and application CD
Warranty information
Installation instructions
To view QuickSpecs and determine the compatibility of this product with your HP workstation, see
http://www.hp.com/go/productbulletin.
The Broadcom NetXtreme Gigabit Ethernet Plus NIC is enabled with Desktop and mobile Architecture
for System Hardware (DASH), a new remote IT management tool for desktop and mobile computers.
In some workstations, the functionality of the DASH feature might be mutually exclusive with some
internal USB accessories, like the HP Media Reader. Systems unable to accommodate both the
Media Reader and the DASH component of this NIC include HP Z600 and HP Z800 Workstations.
ENWW
© 2009, 2010 Hewlett-Packard Development Company, L.P. Printed in the U.S.
Introduction
1

Advertising

   Related Manuals for HP Z600 - Workstation - 6 GB RAM

   Summary of Contents for HP Z600 - Workstation - 6 GB RAM

  • Page 1: Kit Contents, Before You Begin

    USB accessories, like the HP Media Reader. Systems unable to accommodate both the Media Reader and the DASH component of this NIC include HP Z600 and HP Z800 Workstations. © 2009, 2010 Hewlett-Packard Development Company, L.P. Printed in the U.S. ENWW...

  • Page 2: Warnings And Cautions

    Warnings and cautions WARNING! Any surface or area of the equipment marked with this symbol indicates the presence of a hot surface or hot component. If this surface is contacted, the potential for injury exists. To reduce the risk of injury from a hot component, enable the surface to cool before touching. WARNING! Any surface or area of the equipment marked with this symbol indicates the presence of an electrical shock hazard.

  • Page 3: Accessing The Internal Components Of The Computer, Removing Components

    Step 1—Preparing for component installation NOTE: Computer models vary. All illustrations are examples only. Download and install updates Check for available system BIOS updates specified for your HP computer model and operating system at http://www.hp.com/support. Install the system BIOS updates, if available. Accessing the internal components of the computer If you need help preparing the computer for this installation, consult the removal and replacement procedures in the service guide for your computer at...

  • Page 4

    Step 2—Installing the PCIe NIC hardware To install the NIC in the selected PCIe slot: Verify the keyed components of the card align with the socket (1). Close the PCI levers (2). Figure 2 Installing the NIC For workstations that support DASH, attach the USB cable provided to the USB connector on the NIC (3), and then to the DASH-enabled USB dual (10–pin) header on the system board (4).

  • Page 5

    Step 3—Reassembling the workstation Reinstall the card support, if applicable. Reinstall the side access panel. Reconnect power to the workstation and all external devices. Restore power to the workstation and all external devices. Step 4—Installing NIC software For instructions on installing NIC software, see the driver CD supplied with this installation kit. NOTE: At the time of component installation, look for device software, firmware, and driver updates, designated for your workstation model and operating system.

  • Page 6

    Japanese 日本語 This document is available in Japanese. See http://www.hp.com/support/manuals, then select your product and select Japanese from the drop down Manual Language menu. このドキュメントは日本語版が用意されています。http://www.hp.com/support/manuals にアクセス し、ご使用のワークステーション製品を選択し、Manual Language ドロップダウン メニューから Japanese を選択してください。 Broadcom NetXtreme Gigabit Ethernet Plus Network Interface Card installation ENWW...

Comments to this Manuals

Symbols: 0
Latest comments: