Regarding this manual This manual explains how to install Print Client KM and how to use it. Print Client KM can be used with Microsoft Windows 2000 and Windows XP. The intended user of this manual is whom already is aware of Windows 2000 and Windows XP basic operation of “start button”, “task bar”, “mouse”, and “keyboard”.
Configuration PC Hardware requirement to install Print Client KM is as follows. OS (Operation System) Operation guaranteed models, which are equivalent to IBM PC-AT (DOS/V machine), such as Microsoft Windows 2000 and Microsoft Windows XP. Celeron 400 MHz or faster is recommended. System Memory 256 MB or more is recommended.
Installation Method Install KM-4800w Printer Driver prior to install Print Client KM. Installation Procedure of Print Client KM 1. Insert Installation Disk in CD-ROM driver. Double click ”Print Client KM.exe”, which is included in the following shown directory of the disk, and then installation starts.
Page 6
5. Select Unit, and then click [Next]. 6. Select the folder to be installed, and then click [Next].
Page 7
7. Select Program Folder, and then click [Next]. Click [Finish], and finish the installation. “Print Client KM” Icon is created on Desk Top. Installation of Print Client KM is completed.
Page 8
To update the Print Client KM, uninstall the Print Client KM by “Uninstall Print Client KM”, and install the update version of Print Client KM. * Note If you install Print Client KM to a PC which has already installed one, Install Shield Wizard will attempt to uninstall the existing Print Client KM, and will not setup the new one.
Basic output procedure from Print Client KM 4.1. STEP 1: Selection of Output printer Select output printer from Plotter List, which is located on left top of the screen. 4.2. STEP 2: Output Setting Set the output condition using Default Settings, which is located on right side of screen. (Output conditions are output size, output paper and the output quantity.) Output is available without changing anything, normally.
Selected files are registered in the following column. 4.4. STEP 4: Print starts Click the Print button on the right bottom of the screen when all the necessary files have been registered. Files are printed out from the printer. Above shown is the brief operation procedure until it is output.
Operating Print Client KM 5.1. Explanation of Main Window • Contents of the Menu Bar <File> Exit : Print Client KM is finished. <View> View Selected Image : The image of the selected file is displayed in the Viewer. Refresh : The latest information of files and folders is displayed.
Page 15
<Option> Printer Registration : Register printer to use Print Client KM. Reload Sent Jobs : Refer to 20 jobs which have been done already, and can reload any of them. Default Value Setting : Specifies the default Pen Width and Gray for HPGL and Calcomp.
Page 16
: Version information of Print Client KM can be referred. • Selecting Files <Plotter> Decide which plotter the output job is sent. It is possible to output to only KM-4800w printer. <File Type> Specify the displayed file type. All (*.*) Supported Files (*.plt, *.906, *.907, *.tif, *.cal, *.bmp)
Page 17
<Select All> If you click on “Select All”, you can register all of currently displayed files to the output job. <All Clear> If you click on “All Clear”, you can delete all of currently displayed files from the output job. Select files to be printed out.
Page 18
<File Setting> If you wish to check or change the setting information of each registered output file in the “File Name” list, select your required file, then click on “File Setting”. The following “File Setting Dialog Box” appears showing the setting information of that file. At first this dialog box shows the same setting values with “Default Settings”...
Page 19
<Delete All> Click on “Delete All” to delete all of registered output files from the “File Name” list. <Load> Click on “Load” to load the output job that has been registered already. <Save> Click on “Save” to save the output job. <Last Job>...
Page 20
• About Default Settings <Output Size> Select any of the following output sizes from the pull-down menu. (1) Original The output size is as large as output file’s original size. Default setting is “Original”. (2) Percent Both “X : 100.00%” and “X,Y Separate” are validated. If you decide the percentage for “X%”, output file’s original size is enlarged or reduced depending on your percentage setting.
Page 21
<Edit> To change the registered “Custom Size”, click on “Edit” to pop up the “Custom Size Dialog Box”. If you select other output size than “Custom”, “Edit” is invalid. <Delete> To delete the registered “Custom Size”, click on “Delete”. If you select other output size than “Custom”, “Edit” is invalid. <Media Type>...
Page 22
<Count> Decide how many sheets each file is printed out. Setting range is from 1 to 999. <Format Cut> Select either “Standard Cut” or “Synchronous Cut”. If “Standard Cut” is checked, you select the “Standard Cut” and the printing media is cut in some standard size.
Page 23
<Image Placement> The following “Image Placement Dialog Box” appears. As for the detail, refer to “Explanation of Image Placement Dialog Box”.
Page 24
<HPGL Settings> The following “HPGL Setting Dialog Box” appears. As for the detail, refer to “Explanation of HPGL Setting Dialog Box”.
Page 25
<Calcomp Settings> The following “Calcomp Setting Dialog Box” appears. As for the detail, refer to “Explanation of Calcomp Setting Dialog Box”.
Page 26
• About Job Settings <Job Count> Decide how many times a job is outputted. Setting range is from 1 to 999. <Collate> When “Collate” is checked (ON), collation is done. When it is not checked (OFF), collation is not done. Default setting is “Collate ON”. Example : Files A, B and C are printed out 3 jobs for each one.
Page 27
<Output Job> Print: Ordinal printing. Job is sent to Wait Queue. Pause: Job is sent to Pause Queue.
5.2. Explanation of Custom Size Dialog Box <Name> Give a name for your “Custom Size”. You cannot give the name “Custom”. <Width> Input your required width of the output size. Default value is 297.0mm. <Length> Input your required length of the output size. Default value is 210.0mm.
5.3. Explanation of Stamp Setting Dialog Box Click [Stamp] in Default Settings region to pop up “Stamp Settings”. <Stamp Setting> Enter the name to save the new stamp setting. If you click on , you can select any of existent stamp settings from the pull-down menu. <Save>...
Page 30
<Merge Type> If Stamp Image and output image overlaps with each other, the following process is done according to your selection. Opaque Transparent (This function is not valid at raster file) <Gray> Decide the density of the Stamp Image. From 1% to 100% Default value is 100%. <Rotation>...
Page 31
Page Number Page number is printed when multiple pages are filed. Computer Name The name of outputting computer is stamped. <Image> It becomes possible to print the image of selected file as the Stamp Image. <Placement> Decide where to place the image against the text. Left of Text The image is placed to the left of the text.
5.4. Explanation of Image Placement Dialog Box Click [Image Placement] in Default Setting region to pop up “Image Placement” window. <Image Placement> Select any of 9 positions of the output image on the printing media. <Offset> After deciding “Image Placement”, adjust the position more precisely. X : To increase the setting value, the output image is moved to the right.
5.5. Explanation of HPGL Setting Dialog Box Click [HPGL Settings] in Default Settings region to pop up “HPGL Settings” window. <Setting> Input the name here if you will save the new HPGL setting. If you click on, you can select any of existent HPGL settings from the pull-down menu. <Save>...
Page 34
<Gray> Use file setting : To use the gray ratio setting decided in the file. Use custom setting : To use the gray ratio setting decided by “Custom Setting”. Setting range of “Gray” is from 1% to 100% in 1% increment. Default value is 100%.
5.6. Explanation of Calcomp Setting Dialog Box Click [Calcomp Settings] in Default Settings region to pop up “Calcomp Settings” window. <Setting> Input the name here if you will save the new Calcomp setting. If you click on , you can select any of existent Calcomp settings from the pull-down menu. <Save>...
Page 36
<Width> Use file setting : To use the pen width setting decided in the file. Use custom setting : To use the pen width setting decided by “Custom Setting”. Setting range of “Width” is from 0.04mm to 10.00mm in 0.01mm increment. Default value is 0.25mm.
5.7. Explanation of Header Setting Dialog Box Click [Header] in Job Settings region to pop up “Header Settings” window. <Placement> Leading Left Header is printed at the left.(4mm from the leading edge) Leading Right Header is printed at the right.(4mm from the leading edge) Trailing Left Header is printed at the left.(4mm from the trailing edge) Trailing Right...
Page 38
Print Client KM User’s Manual 2008. 7 Rev. 1.0 The Copyright Act protects this manual. It is prohibited to copy or duplicate all or a part of this manual without permission.