Page of 11

HP 3020 - Cisco Catalyst Blade Switch Getting Started Manual

Cisco catalyst blade switch 3020 for hp getting started guide.
Hide thumbs
Cisco Catalyst Blade Switch 3020 for HP Getting Started Guide [Cisco Catalyst Blade Switch 3000 Series] - Cisco Systems
Home
|
Skip to Content
|
Skip to Search
|
Skip to Navigation
|
Skip to Footer
Worldwide [change]
Log In |Register |About Cisco
Guest
Search
Search
Solutions
Products & Services
Hierarchical Navigation
HOME
SUPPORT
PRODUCT SUPPORT
SWITCHES
CISCO CATALYST BLADE SWITCH 3000
SERIES
INSTALL AND UPGRADE
INSTALL AND UPGRADE
GUIDES
Cisco Catalyst Blade
Switch 3020 for HP
Getting Started Guide
Feedback: Help us help you
Please rate this document.
Excellent
Good
Average
Fair
Poor
This document solved my
problem.
Yes
No
Just
Browsing
Suggestions to improve this
document.
(512 character limit)
If you have provided a
suggestion, please enter your
full name and e-mail
address. This information is
optional and allows us to
contact you if necessary.
Name:
E-mail:
Submit
http://www.cisco.com/en/US/products/ps6748/products_getting_started_guide09186a00806c38a8.html (1 of 11)4/19/2007 10:27:47 AM
|
Ordering
Cisco Catalyst Blade Switch 3000 Series
Cisco Catalyst Blade Switch 3020 for HP Getting Started Guide
Table Of Contents
Cisco Catalyst Blade Switch 3020 for HP
Getting Started Guide
Introduction
Taking Out What You Need
Cisco Gigabit Ethernet Switch Module Description
HP c-Class BladeSystem Architecture
Installing the Switch Module in the Blade Server
Information You Need to Run Express Setup
Using Express Setup to Assign a VLAN 1 IP Address to the Switch Module
Using the Onboard Administrator to Assign an IP Address to the Switch Module fa0 Interface
Completing the Express Setup Fields
Managing the Switch Module
Command-Line Interface
Onboard Administrator Command-Line Interface
Troubleshooting Express Setup
Accessing Help Online
Cisco.com
Cisco Technical Support & Documentation Website
Cisco 90-Day Limited Hardware Warranty Terms
HP Hardware Warranty Terms
Getting Started Guide
Cisco Catalyst Blade Switch 3020 for HP
Getting Started Guide
INCLUDING LICENSE AND WARRANTY
1 Introduction
This guide provides instructions on how to install your Cisco Catalyst Blade Switch 3020 for HP—hereafter referred to as the switch module—in the HP c-Class BladeSystem and to set up and configure your switch module. The HP c-Class BladeSystem—hereafter referred to as the blade server—
supports up to eight Ethernet switch modules, which are installed in the interconnect bays of the blade server.
This guide also covers management options and troubleshooting help for the switch module.
For details on the numbers, types, and the location of the blade server bays, for additional information on the blade server system, and for detailed port mapping information, see the HP BladeSystem enclosure installation poster or the HP BladeSystem enclosure setup and installation guide at
www.hp.com/go/bladesystem/documentation.
For additional installation and configuration information about the switch module, see the Cisco Catalyst Blade Switch 3020 for HP documentation on Cisco.com. For system requirements, important notes, limitations, open and resolved caveats, and last-minute documentation updates about the switch
module, see the release notes, also on Cisco.com.
When using the online publications, refer to the documents that match the Cisco IOS software version that is running on the switch module. See the "Obtaining Documentation" section on page 1-24 for more information about the switch module publications.
For translations of the warnings that appear in this publication and all safety and handling warnings for this product, see the Regulatory Compliance and Safety Information for the Cisco Catalyst Blade Switch 3020 for HP that accompanies this guide.
Before proceeding, read the release notes for the blade server. The release notes are available on the HP support website at
2 Taking Out What You Need
These items ship with your switch module:
Console cable
Cisco Catalyst Blade Switch 3020 for HP Getting Started Guide (this book)
Regulatory Compliance and Safety Information for the Cisco Catalyst Blade Switch 3020 for HP
Registration card
Follow these steps:
1.
Unpack and remove the switch module and the accessory kit from the shipping box.
2.
Return the packing material to the shipping container, and save it for future use.
If the switch modules are ordered with the blade server, the switch modules are already installed. The unpacking procedure for the switch module applies only if one is ordered separately. See the blade server documentation for the unpacking procedure for the HP equipment.
Cisco Gigabit Ethernet Switch Module Description
The Cisco Catalyst Blade Switch 3020 for HP is a 24 Gigabit Ethernet port, Layer 2+ switch module. Sixteen of the Gigabit Ethernet ports are internal 1000BASE-X downlink ports that connect to the blade server. The other eight Gigabit Ethernet ports are external uplink ports that provide connections to
other switches or routers. Uplink ports operate at 10/100/1000 Mbps if used as RJ-45 ports and operate at 1000 Mbps if small form-factor pluggable (SFP) fiber-optic modules are installed. See
Figure 1
shows the switch module.
Support
Training & Events
www.support.hp.com.
Partner Central
Table 1
for more detailed descriptions of the switch module ports.
Downloads
Cisco Catalyst Blade Switch
3020 for HP Getting Started
Guide
http://

Advertising

   Related Manuals for HP 3020 - Cisco Catalyst Blade Switch

   Summary of Contents for HP 3020 - Cisco Catalyst Blade Switch

  • Page 1

    Cisco Catalyst Blade Switch 3020 for HP Getting Started Guide [Cisco Catalyst Blade Switch 3000 Series] - Cisco Systems Home Skip to Content Skip to Search Skip to Navigation Skip to Footer Worldwide [change] Log In |Register |About Cisco Guest Search Search Solutions...

  • Page 2

    Cisco Catalyst Blade Switch 3020 for HP Getting Started Guide [Cisco Catalyst Blade Switch 3000 Series] - Cisco Systems Figure 1 The Catalyst Blade Switch 3020 for HP Switch module Health LED Release latch SFP module port LEDs for ports 17 to 20 System status LEDs SFP module ports 17 to 20 Mode button...

  • Page 3

    Cisco Catalyst Blade Switch 3020 for HP Getting Started Guide [Cisco Catalyst Blade Switch 3000 Series] - Cisco Systems • See the HP c-Class documentation for information on the port mapping between blade servers and the switch modules. 4 Installing the Switch Module in the Blade Server Before you install the switch module in the blade server, consider these points: •...

  • Page 4: Switch Module Ip Addresses, Running Express Setup

    Cisco Catalyst Blade Switch 3020 for HP Getting Started Guide [Cisco Catalyst Blade Switch 3000 Series] - Cisco Systems Switch Module IP Addresses IP addresses can be assigned to two of the switch module interfaces: • The fa0 Ethernet interface. This Layer 3 Ethernet interface is connected to the Onboard Administrator through which you can manage the switch module. It is used only for switch module management traffic, not for data traffic. •...

  • Page 5

    Cisco Catalyst Blade Switch 3020 for HP Getting Started Guide [Cisco Catalyst Blade Switch 3000 Series] - Cisco Systems Caution Do not connect the switch module to any device other than the PC or workstation being used to configure it. Step 7 Connect the other end of the cable to the Ethernet port on the PC or workstation.

  • Page 6

    Cisco Catalyst Blade Switch 3020 for HP Getting Started Guide [Cisco Catalyst Blade Switch 3000 Series] - Cisco Systems Note See the Onboard Administrator user guide at http://www.hp.com/go/bladesystem/documentation for more information about configuring and using the Onboard Administrator. After you install the switch module in the interconnect module bay, after approximately 2 minutes, the switch module automatically obtains an IP address for its fa0 interface through the Onboard Administrator. This method of obtaining an IP address occurs if a DCHP server is configured on the same network, or if the Onboard Administrator is configured as a DHCP server.

  • Page 7: Refreshing The Pc Ip Address, Using The Device Manager

    Cisco Catalyst Blade Switch 3020 for HP Getting Started Guide [Cisco Catalyst Blade Switch 3000 Series] - Cisco Systems Step 8 Go to "Completing the Express Setup Fields" section to finish setting up the switch module using the Express Setup screen of the Device Manager. Completing the Express Setup Fields Follow these steps to finish setting up the switch module: Step 1 Enter this information in the Network Settings fields:...

  • Page 8: Other Management Options, In Case Of Difficulty, Resetting The Switch Module, For More Information

    Cisco Catalyst Blade Switch 3020 for HP Getting Started Guide [Cisco Catalyst Blade Switch 3000 Series] - Cisco Systems For more advanced configuration, download and run the Cisco Network Assistant, which is described in the next section. Command-Line Interface You can enter Cisco IOS commands and parameters through the CLI. Access the CLI either by connecting your PC directly to the switch module console port or through a Telnet session from a remote PC or workstation. Follow these steps: Connect the supplied RJ-45-to DB-9 adapter cable to the standard 9-pin serial port on the PC.

  • Page 9: Obtaining Documentation, Product Documentation Dvd, Ordering Documentation, Documentation Feedback, Cisco Product Security Overview

    Cisco Catalyst Blade Switch 3020 for HP Getting Started Guide [Cisco Catalyst Blade Switch 3000 Series] - Cisco Systems 8 Obtaining Documentation Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain technical assistance and other technical resources. These sections explain how to obtain technical information from Cisco Systems. Cisco.com You can access the most current Cisco documentation at this URL: http://www.cisco.com/techsupport...

  • Page 10: Definitions Of Service Request Severity, Obtaining Additional Publications And Information, Hardware Warranty Terms

    Cisco Catalyst Blade Switch 3020 for HP Getting Started Guide [Cisco Catalyst Blade Switch 3000 Series] - Cisco Systems To open a service request by telephone, use one of the following numbers: Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227) EMEA: +32 2 704 55 55 USA: 1 800 553-2447 For a complete list of Cisco TAC contacts, go to this URL:...

  • Page 11

    Hewlett-Packard Company shall not be liable for technical or editorial errors or omissions contained herein. The information in this document is provided "as is" without warranty of any kind and is subject to change without notice.

Comments to this Manuals

Symbols: 0
Latest comments: