Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Alliance Laundry Systems Drying Tumblers 50 Pound Capacity 75 Pound Capacity Model Identification Part No. 70400301R3
Summary of Contents for Alliance Laundry Systems Drying Tumblers 50 Pound Capacity 75 Pound Capacity Model Identification Part No. 70400301R3
- Page 1 Drying Tumblers Refer to Page 3 for Model Identification Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) 50 Pound Capacity 75 Pound Capacity www.comlaundry.com Part No. 70400301R3 August 2007...
- Page 3 These instructions must be posted in a prominent location. Step-by-step instructions of the above safety information must be posted in a prominent location near the tumbler for customer use. 70400301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT MISE EN GARDE POUR VOTRE SÉCURITÉ, les informations de ce guide doivent être respectées afin de...
-
Page 4: Table Of Contents
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Introduction... -
Page 5: Introduction
3V – DX4 vended 3X – DX4 prep for coin CD – rotary coin drop CX – prep for coin DO – DMP OPL 70400301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Introduction Steam/Thermal Oil BT050T BU050T CHD50S2-CT050S... -
Page 6: Customer Service
Refer to Figure 1. Serial Plate Figure 1 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Wiring Diagram The wiring diagram is located in the junction or contactor box. -
Page 7: Safety Information
70400301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Safety Information IMPORTANT: Warranty is void unless tumbler is installed according to instructions in the Installation Manual. -
Page 8: Important Safety Instructions
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 14. The interior of the tumbler and the exhaust duct should be cleaned periodically by qualified service personnel. - Page 9 28. DO NOT operate the tumbler if it is smoking, grinding, has missing or broken parts. 70400301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 29. DO NOT bypass any safety devices. 30. Solvent vapors from dry-cleaning machines create acids when drawn through the heater of the drying unit.
-
Page 10: Operating Instructions
NOTE: Activation of the emergency stop button stops all machine control circuit functions, but DOES NOT remove all electrical power from machine. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT WARNING Operating Instructions Step 1: Clean Lint Screen/Compartment Remove any accumulated lint from the lint screen and compartment. -
Page 11: Control Instructions
3. Press the PUSH TO START button and hold it for approximately three (3) seconds. 70400301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT SELECT TEMPERATURE TEMP... -
Page 12: Manual Timer Control
5. Press the PUSH TO START button in and hold it in for approximately three seconds. This starts the tumbler cycle. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT REVERSING MODELS HEAT TEMPERATURE... -
Page 13: Dual Digital Timer Control
70400301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT REVERSING MODELS TMB2136N TMB2136N... -
Page 14: To Program A Short Test Cycle
AF - 1 started Airflow switch failed to close after AF - 2 cycle started © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT WARNING Definition Check thermistor. Replace if inoperative. ● Check wiring diagram between control and ●... -
Page 15: Single Drop Control
5 seconds, with a cycle in process, the control will enter Start Mode once power is restored. 70400301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Figure 7 If the dry time dipswitch settings have not changed from the factory default, the IN USE LED will flash two to five times, depending on model. -
Page 16: Temperature Selector Switch
Airflow switch opened/closed 5 or AF (flashing) more times in a running cycle. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Temperature Selector Switch For five minutes after the control is powered up, there is a diagnostic feature that allows the temperature selector switches to be tested. -
Page 17: Diagnostic Microprocessor Control
● Monitors the thermistor for operation ● 70400301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Cool Time (Min.) Table 1 The minimum drying time is 0 minutes, and the minimum cooling time is 2 minutes. The maximum drying or cooling time is 60 minutes. -
Page 18: Dmp Coin
COOLING LED. Illuminated when in the cooling cycle or when the display is currently showing the time for the cooling cycle. START. Starts or resumes the current program or cycle Temperature Select. This button toggles through the three temperature selections. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT MINUTES HIGH MEDIUM TEMP PERM. - Page 19 2. An LED will be on to indicate which parameter is flashing on the display. 70400301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operating Instructions 3. The hidden front panel increment and decrement keys are used to change the value.
-
Page 20: Dmp Opl Models
COOLING LED. Illuminated when in the cooling cycle, or when the display is currently showing the time for the cooling cycle. TEMPERATURE LED. Illuminated when the display is showing the temperature setting. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT DRYING COOLING... -
Page 21: Dip Switch Settings
“ON” indicates that the buzzer will sound continuously until the STOP button is pressed or the loading door is opened. 70400301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Coin Table 2 7. Safety Tumble (OPL) or Coin count/Pay (Coin): If DIP switch #1 is set for OPL, then DIP switch #7 in the ON position enables the safety tumble. -
Page 22: Reversing Operation
13. Toggle between reversing REV (illuminated) or nonreversing REV (not illuminated). (Only for tumblers with the reversing option.) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 14. To cancel this temporary programming mode push the STOP button once to stop the current cycle and once more to cancel the modified program settings. - Page 23 70400301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operating Instructions Operational Check for the Board Diagnostics 1. “dor” indicates that the loading or lint door is open.
-
Page 24: Ignition Control Operation
The ignition control will remain in Run Mode until 24VAC is removed from terminals TH and GND on the control. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Termination of Flame The flame will go out when power is removed from ignition control. -
Page 25: Gas Valve
Diagnostic (DGN) LED Figure 10 70400301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Diagnostic LED (DGN LED) / Error Codes The Diagnostic LED or DGN LED is located by the power connector on the ignition control. Refer to Figure 10. -
Page 26: Maintenance
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Maintenance WARNING e. Carefully wipe any accumulated lint off of the cabinet high limit thermostat and thermistor. -
Page 27: Monthly
4. Check flow of combustion and ventilation air. 5. Check belt tension and condition. Replace worn or cracked belts. 70400301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT WARNING Bi-Annually 1. Check mounting hardware for any loose nuts, bolts or screws. -
Page 28: Daily Maintenance
Lint buildup will act as an insulator, causing machine to overheat. Clean lint and debris buildup from blower to maintain proper airflow, to avoid overheating and prevent possible vibration. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT WARNING W002 70400301... -
Page 29: Quarterly Maintenance
Check cylinder and front panel seals. Inspect cabinet and inner panels for any damage, replace or repair as needed. Clean burner tubes of any lint buildup. 70400301 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT WARNING Maintenance W002... -
Page 30: Copyright, Alliance Laundry Systems Llc – Do Not Copy Or Transmit
For technical assistance, call (920) 748-3121. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Possible Reason – Corrective Actions Insert correct coin(s) or valid card if applicable.
Need help?
Do you have a question about the Drying Tumblers 50 Pound Capacity 75 Pound Capacity Model Identification Part No. 70400301R3 and is the answer not in the manual?
Questions and answers