Table of Contents
Advertisement
Quick Links
ULTRA FLAME
INSTALLATION AND OPERATING INSTRUCTIONS
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND
LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.
Manufactured by :
DROLET STOVES & FIREPLACES INC.
1700, Leon-Harmel
Quebec, Qc (Canada)
G1N 4R9
FIREPLACE GAS INSERT
FOR YOUR SAFETY
FOR YOUR SAFETY
IF YOU SMELL GAS :
1. OPEN WINDOWS
2. TURN OFF MAIN GAS SUPPLY
3. DON'T TOUCH ELECTRICAL SWITCHES
4. EXTINGUISH ANY OPEN FLAME
5. IMMEDIATELY CALL YOUR GAS SUPPLIER
Tested by :
WARNOCK HERSEY
Rev. 07/96 45028A
Advertisement
Table of Contents
Related Manuals for Drolet 36C03U TYPE 139
Summary of Contents for Drolet 36C03U TYPE 139
- Page 1 2. TURN OFF MAIN GAS SUPPLY 3. DON’T TOUCH ELECTRICAL SWITCHES 4. EXTINGUISH ANY OPEN FLAME 5. IMMEDIATELY CALL YOUR GAS SUPPLIER Manufactured by : DROLET STOVES & FIREPLACES INC. 1700, Leon-Harmel Quebec, Qc (Canada) G1N 4R9 FIREPLACE GAS INSERT...
-
Page 2: Table Of Contents
GENERAL INFORMATION :... WARNING :... SPECIFICATIONS :... TOP, SIDE AND FRONT VIEWS :... INSTALLATION :... GLASS FRONT REMOVAL CLEANING AND INSTALLATION :... 11 BURNER REMOVAL AND INSTALLATION :... 12 LOG INSTALLATION :... FACE PLATE ASSEMBLY AND INSTALLATION :... 14-15 REFRACTORY PANELS INSTALLATION :... 16 EMBERS KIT INSTALLATION :... -
Page 3: General Information
GENERAL INFORMATION : The ULTRA FLAME is a high efficiency fireplace gas insert with an input rating of 30 000 Btu/h with natural gas and 26 000 Btu/h with propane. It features a millivolt valve with a constant pilot. This lets you choose between a wall mounted switch, a wireless remote control to turn on or off the main flame at will. -
Page 4: Warning
WARNING * INSTALLATION SHOULD BE DONE BY A QUALIFIED INSTALLER. * DO NOT BURN WOOD OR ANY OTHER MATERIAL IN THE GAS INSERT. * HOT WHEN IN OPERATION. KEEP, FURNITURE, CLOTHING AND FLAMMABLE MATERIAL AWAY FROM THE APPLIANCE. * ADVISE ADULTS AND CHILDREN TO THE HAZARD OF HIGH SURFACE TEMPERATURES AND THAT THEY SHOULD STAY AWAY TO AVOID BURNS OR CLOTHING IGNITION. -
Page 5: Specifications
Min inlet pressure : Max inlet pressure : Vent size : 4” Diam. listed gas liner Valve : Natural gas White Rogers Model 36C03U TYPE 139 Millivolt operated Nova model Millivolt operated Blower : Variable speed, 140 CFM Thermo-switch :... -
Page 6: Top, Side And Front Views
TOP, SIDE AND FRONT VIEWS :... - Page 7 INSTALLATION : When the masonry fireplace that will receive the ULTRA FLAME gas insert is thoroughly cold, remove all ashes and vacuum clean. Remove the glass front from the gas insert following page 11 instructions. Remove the burner and firebox bottom plate from the gas insert following page 12 instructions.
- Page 8 Secure the liner to the 4” connector on the top of the ULTRA FLAME with three metal screws. Push the ULTRA FLAME back in the fireplace while pulling the draft hood in place. To do so, fix two ropes to the draft hood sliders. Make sure the draft hood front lip is squeezed under the steel angle to prevent any motion.
- Page 9 Install a 1/8” NPT plugged tapping for test gauge connection immediately upstream of the gas supply connection to the appliance. Install a shutoff valve to the gas line. Tighten securely using a pipe joint compound. Install a 3/8” flex connector to connect the shutoff valve to the gas valve on the fireplace.
- Page 10 - Install the wall switch in a convenient location. Route a proper sized wire from the switch or the thermostat to the gas valve. Distance between valve and switch 8’ 12’ 20’ 32’ 50’ - Connect the wires in serial with the face plate flame switch ( green wires ). NOTE : DO NOT CONNECT THE WALL SWITCH WIRE OR THE VALVE TO 120 VOLTS POWER SUPPLY LINE.
-
Page 11: Installation
Install the firebox bottom plate and burner following page 12 instructions. Install the 4 logs on the burner as shown on page 13. If so desired, install the embers kits as shown on page 16. Install the glass front following page 11 instructions. Install the face plate according to page 14 instructions. -
Page 12: Glass Front Removal Cleaning And Installation
GLASS FRONT REMOVAL CLEANING AND INSTALLATION : * To remove the glass front, unscrew the six screws holding it in place as shown. CAUTION : Hold the glass while unscrewing to prevent it from falling. * Clean the glass only with liquid cleaners or soaps and water, do not use abrasive cleaners which could remove the coating on the glass. -
Page 13: Burner Removal And Installation
BURNER REMOVAL AND INSTALLATION : REMOVAL : Slide the burner to the left and pull toward you. To gain access to the fan, also remove the firebox bottom plate. INSTALLATION : Put the bottom plate back in place. Put the burner assembly back in the firebox and push to the right until it touches the firebox side. -
Page 14: Log Installation
LOG INSTALLATION : Remove the glass front as described on page 11. Install the longer log in back of the firebox with locating grooves on top. Install the 14” log in the front of the firebox and to the right. Make sure the log is pushed against the metal retainer on the burner face. -
Page 15: Face Plate Assembly And Installation
FACE PLATE ASSEMBLY AND INSTALLATION : ASSEMBLY : Bolt the face plate top piece to the left piece using two #10-24 x 1/2 bolts and nuts (B). Place both louver assemblies in position with their pivot rod inserted through the face plate side pieces holes (C). - Page 16 INSTALLATIONS : Screw the air deflector on the unit as shown using three #10 x 1/2 metal screws. Bring the face plate in position on the gas insert taking care to slip the air deflector between the top louver and the bottom of the top piece. Secure using four #10 x 1/2 metal screws (D).
-
Page 17: Refractory Panels Installation
REFRACTORY PANELS INSTALLATIONS : Remove the front glass as described on page 11. Remove the logs from the firebox. Install the two sides refractory panels and pull them forward as mush as possible to help insertion of the back panel. Place the back refractory against the back of the firebox. -
Page 18: Operating Instructions
OPERATING INSTRUCTIONS LIGHTING INSTRUCTIONS : Open the bottom louvers of the face plate to reach the control. Turn the gas valve knob to the “OFF” position and wait 5 minutes. Note : You have to depress the gas valve knob to turn from “PILOT” to “OFF” or from “OFF”... -
Page 19: Maintenance Instructions
MAINTENANCE INSTRUCTIONS : TURN OFF THE GAS WITH THE SHUTDOWN VALVE AND THE ELECTRICAL POWER BEFORE SERVICING THE APPLIANCE. * The venting system and the gas insert should be inspected at least once a year. * Remove the glass front and the logs clean them if necessary. * The control compartment, air circulating passages, firebox, logs and burner should be cleaned at least once a year by vacuuming or brushing. -
Page 20: Optional Parts
OPTIONAL PARTS ITEM DESCRIPTION Face plate, silver gray enamel Face plate, black enamel Face plate, gold Face plate, charcoal painted Face plate, black painted Wall switch Remote control Decorative refractory kit REPLACEMENT PARTS ITEM DESCRIPTION Log kit Back log only Front log only Top log, small only Top log, holed only... -
Page 21: Limited 5 Years Warranty
All other costs related to dismantling the structure, decoration, venting system, etc. are the responsibilities of the fireplace gas insert owner. During the second to the fifth year of the limited warranty, DROLET STOVES AND FIREPLACES INC. will replace defective parts free of charge except the VALVE,...