Page 1 Ram Truck 2 0 1 0 O W N E R ’ S M A N U A L C H A S S I S...
Page 2 VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents.
Page 3: Introduction
TABLE OF CONTENTS SECTION ............3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 5: Table Of Contents
CONTENTS A Message From Chrysler Group LLC ..4 How To Use This Manual ....5 Warnings And Cautions .
Page 6: A Message From Chrysler Group Llc
4 INTRODUCTION A MESSAGE FROM CHRYSLER GROUP LLC Chrysler Group LLC and Cummins welcome you as a Cummins turbocharged diesel-powered truck owner. Your diesel truck will sound, feel, drive, and operate differently from a gasoline-powered truck. It is important that you read and understand this manual. Almost 100% of the heavy duty trucks in the United States and Canada are diesel-powered because of the fuel economy, rugged durability, and high torque which per-...
Page 7: How To Use This Manual
This information cannot be erased and will stay in the system’s memory even if the modification is removed. This information can be retrieved by Chrysler Group LLC, and service and repair facilities, when servicing your vehicle. This information may be used to determine if repair will be covered by warranty.
Page 8 6 INTRODUCTION...
Page 9: Van Conversions/Campers
WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against op- erating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information.
Page 10: Vehicle Identification Number
8 INTRODUCTION VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is found on the left front corner of the instrument panel, visible through the windshield. This number also appears on the Auto- mobile Information Disclosure Label affixed to a window on your vehicle, the vehicle registration and title.
Page 11: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Ignition Key Removal ....12 Locking Doors With A Key .
Page 12 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Using The Panic Alarm ....21 Programming Additional Transmitters ..21 General Information .
Page 13 Airbag Deployment Sensors And Controls . . . 48 Event Data Recorder (EDR) ....56 Child Restraint ..... . . 58 Engine Break-In Recommendations .
Page 14: Things To Know Before Starting Your Vehicle 9
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The authorized dealer that sold you your vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your authorized dealer.
Page 15: Locking Doors With A Key
NOTE: • If you try to remove the key before you place the shift lever in PARK, the key may become trapped tempo- rarily in the ignition cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described.
Page 16: Steering Wheel Lock - If Equipped
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE STEERING WHEEL LOCK — IF EQUIPPED Your vehicle may be equipped with a passive steering wheel lock. This lock prevents steering the vehicle with- out the key fob. If the steering wheel is moved approxi- mately a half turn in either direction and the key fob is not in the ignition switch, the steering wheel will lock.
Page 17: Replacement Keys
During normal operation, after turning on the ignition switch, the Vehicle Security Light will turn on for three seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics.
Page 18: Customer Key Programming
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE dealer or by following the customer key programming procedure. This procedure consists of programming a blank key to the vehicle electronics. A blank key is one that has never been programmed. NOTE: When having the Sentry Key System serviced, bring all vehicle keys with you to an authorized dealer.
Page 19: General Information
Repeat this procedure to program up to eight keys. If you do not have a programmed Sentry Key , contact your authorized dealer for details. NOTE: If a programmed key is lost, see your authorized dealer to have all remaining keys erased from the sys- tem’s memory.
Page 20: To Set The Alarm
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Set the Alarm The Vehicle Security Alarm will set when you use the power door locks, or use the Remote Keyless Entry (RKE) transmitter to lock the doors. After all the doors are locked and closed, the Vehicle Security Light in the instrument cluster will flash rapidly to signal that the Vehicle Security Alarm is arming.
Page 21: Illuminated Entry - If Equipped
ILLUMINATED ENTRY — IF EQUIPPED The courtesy lights will turn on when you use the Remote Keyless Entry (RKE) transmitter or open the doors. This feature is only available if you have Remote Keyless Entry. The lights will fade to off after approximately 30 seconds, or they will immediately fade to off once the ignition switch is turned ON.
Page 22: To Unlock The Doors
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Unlock the Doors Press and release the UNLOCK button on the RKE transmitter once to unlock only the driver’s door or twice to unlock all the doors. When the UNLOCK button is pressed, the illuminated entry will initiate, the parking lights will flash on twice and, if installed, the cargo lamp will turn on for 30 seconds.
Page 23: Using The Panic Alarm
3. Continue to hold the LOCK button, wait at least 4 seconds, but no longer than 10 seconds, then press and hold the PANIC button. Release both buttons at the same time. 4. To reactivate this feature, repeat the above steps. This vehicle is shipped from the assembly plant with the park lamp flash feature activated.
Page 24: General Information
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2.
Page 25: Remote Starting System - If Equipped
2. Remove and replace the battery. When replacing the battery, match the + sign on battery to the + sign on the inside of the battery clip, located on back cover. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration.
Page 26 24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Ignition key removed from ignition switch • Battery at an acceptable charge level • RKE PANIC button not pressed WARNING! • Do not start or run an engine in a closed garage or confined area.
Page 27: Door Locks
Remote start will also cancel if any of the following occur: • The engine stalls or RPM exceeds 2500 • Any engine warning lamps come on • The hood is opened • The hazard switch is pressed • The transmission is moved out of PARK •...
Page 28: Power Door Locks - If Equipped
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The ignition key will unlock all the locks on your vehicle. WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors when you drive as well as when you park and leave the vehicle.
Page 29 Automatic Door Locks – If Equipped If this feature is enabled, your door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). Automatic Door Lock Programming This feature is enabled when your vehicle is shipped from the assembly plant and can be disabled by using the following procedure: 1.
Page 30: Child Protection Door Lock - Quad Cab Only
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Fasten your seat belt. (Fastening the seat belt will cancel any chimes that may be confusing during this programming procedure.) 3. Insert the key into the ignition. 4. Within 15 seconds, cycle the key from the LOCK position to the ON/RUN position a minimum of four times, ending in the ON/RUN position.
Page 31 To use the system, open each rear door, slide the lever UP to engage the locks and DOWN to disengage the child protection door locks. When the system on a door is engaged, that door can only be opened by using the outside door handle even, if the inside door LOCK is in the UNLOCKED position.
Page 32: Windows
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOWS Power Windows – If Equipped Power Window Switches The control on the left front door panel has up-down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window control and on the rear doors of Quad Cab windows will operate when the ignition switch is turned...
Page 33: Wind Buffeting
Auto-Down (Driver’s Side Only) The driver’s window switch has an Auto-Down feature. Press the window switch past the detent, release, and the window will go down automatically. Window Lockout Switch (4-Door Models Only) The window lockout switch on the driver’s door allows you to disable the window control on the other doors.
Page 34: Occupant Restraints
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems: •...
Page 35: Lap/Shoulder Belts
Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision.
Page 36 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision best. Wearing your belt in the wrong place could make your injuries in a collision much worse.
Page 37 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 Latch Plate To Buckle 1 — Latch Plate 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.”...
Page 38 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal inju- ries. Always buckle your belt into the buckle nearest you.
Page 39 Removing Slack From Belt THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen.
Page 40 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system.
Page 41 panel and insert it into the black keyed buckle until there is an audible “click”. For proper seatbelt usage, refer “Lap/Shoulder Belt Operating Instructions” in this section. WARNING! • If the black latch and black buckle are not prop- erly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in a collision.
Page 42: Adjustable Upper Shoulder Belt Anchorage
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In Use Position WARNING! • If the black latch and black buckle are not prop- erly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in a collision.
Page 43: Automatic Locking Restraint (Alr) Mode - If Equipped
away from your neck. Press the button located on the upper belt guide, and then move it up or down to the position that fits you best. Adjusting Upper Shoulder Belt As a guide, if you are shorter than average you will prefer a lower position, and if you are taller than average THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 you will prefer a higher position.
Page 44: Center Lap Belts
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Grasp the shoulder portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the Automatic Locking Mode.
Page 45: Seat Belts And Pregnant Women
BeltAlert will be reactivated if the driver’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h). BeltAlert can be enabled or disabled by your authorized dealer or by following these steps: NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or START position.
Page 46: Seat Belt Extender
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Extender If a seat belt is too short even when fully extended, your authorized dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long enough.
Page 47: Advanced Front Airbag Features
NOTE: These airbags are certified to the new Federal regulations for Advanced Airbags. The Advanced Front Airbags have a multistage inflator design. This allows the airbag to have different rates of inflation based on the severity and type of collision. This vehicle may also be equipped without a passenger’s front airbag.
Page 48 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the second stage determines whether the output force is low, medium, or high. If a low output is sufficient to meet the need, the remaining gas in the inflator is expended. WARNING! •...
Page 49 WARNING! Infants in rear-facing child restraints must NEVER- ride in the front seat of a vehicle with a passenger front airbag unless the airbag is turned off (Regular Cab Vehicles Only). An airbag deployment can cause severe injury or death to infants in that position. Refer to the “Passenger Airbag On/Off Switch (if equipped)”...
Page 50: Airbag Deployment Sensors And Controls
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center. Phone numbers are provided under If You Need Assistance in Section 9 of this manual. WARNING! •...
Page 51 type of collision. Advanced Front Airbags are not ex- pected to reduce the risk of injury in rear, or side collisions. The Advanced Front Airbags will not deploy in all frontal collisions, including some that may produce substantial vehicle damage — for example, some pole collisions, truck underrides, and angle offset collisions.
Page 52 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE It also includes diagnostics that will illuminate the instru- ment cluster Airbag Warning Light if a malfunction is noted. The diagnostics also record the nature of the malfunction. WARNING! Ignoring the Airbag Warning Light in your instru- ment panel could mean you won’t have the airbags to protect you in a collision.
Page 53 The passenger front airbag is to be turned off only if the passenger: • is an infant (less than one year old) who must ride in the front seat because there is no rear seat, because the rear seat is too small for a rear-facing infant restraint or because the infant has a medical condition which makes it necessary for the driver to be able to see the infant,...
Page 54 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Turn On the Passenger Airbag (Regular Cab Vehicles Only) – If Equipped Place the ignition key in the Passenger Airbag On/Off Switch (If Equipped), push the key in and turn counter- clockwise, and remove the key from the switch.
Page 55 Enhanced Accident Response System In the event of an impact causing airbag deployment, if the communication network remains intact, and the power remains intact, depending on the nature of the event the ORC will determine whether to have the Enhanced Accident Response System perform the follow- ing functions: •...
Page 56 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • As the airbags deflate, you may see some smoke-like particles. The particles are a normal by-product of the process that generates the non-toxic gas used for airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat.
Page 57 Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
Page 58: Event Data Recorder (Edr)
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Warning Light You will want to have the airbags ready to inflate for your protection in a collision. While the airbag system is designed to be mainte- nance free, if any of the following occurs, have an authorized dealer service the system immediately.
Page 59 2. Under certain circumstances, EDR data may not be recorded (e.g., loss of battery power). In conjunction with other data gathered during a com- plete accident investigation, the electronic data may be used by Chrysler Group LLC and others to learn more about the possible causes of crashes and associated injuries in order to assess and improve vehicle perfor- mance.
Page 60: Child Restraint
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Requested by police under a legal warrant. 4. Otherwise required by law. Data parameters that are recorded: • Diagnostic trouble code(s) and warning light status for electronically-controlled safety systems, including the airbag system •...
Page 61 Infants and Small Children There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Use the restraint that is correct for your child. • Safety experts recommend that children ride rearward- facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg).
Page 62 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE cannot sit with knees bent over the vehicle’s seat cushion while the child’s back is against the seat back, they should use a belt-positioning booster seat. The child and booster seat are held in the vehicle by the lap/shoulder belt.
Page 63 • The restraint must be appropriate for your child’s weight and height. Check the label on the restraint for weight and height limits. • Carefully follow the instructions that come with the restraint. If you install the restraint improperly, it may not work when you need it.
Page 64 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Buckle the child into the seat according to the child restraint manufacturer’s directions. • When your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle. Do not leave it loose in the vehicle.
Page 65 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 Regular Cab Passenger Seat Quad Cab Rear Outboard Seats...
Page 66 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seat back tether anchorage have been available for some time.
Page 67 Installing the Child Restraint System WARNING! Do not install child restraint systems equipped with LATCH attachments in the center position of a Quad Cab model rear seat. The LATCH anchorages in this seat are designed for the two outboard seating posi- tions only.
Page 68 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
Page 69 2. Lift the cover (if so equipped), and attach the hook to the square opening in the sheet metal. 3. Install the child restraint and remove the slack in the tether strap according to the manufacturer’s instructions. Regular Cab with Any Bench Seat 1 —...
Page 70 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. Place a child restraint on the center rear seat and adjust the tether strap so that it will reach under the head restraint to the tether anchor directly behind the seat and to the anchor directly behind the right seat.
Page 71 Tether Anchorage Points at All Three Seating Positions 1. Place the child restraint on the seat and adjust the tether strap so that it will reach over the seat back under the head restraint to the tether anchor directly behind the seat.
Page 72: Engine Break-In Recommendations
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children Too Large for Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seat back should use the lap/shoulder belt in a rear seat.
Page 73: Safety Tips
• Warm up the engine before placing it under load. • Do not operate the engine at idle for prolonged periods. • Use the appropriate transmission gear to prevent engine lugging. • Observe vehicle oil pressure and temperature indica- tors. •...
Page 74: Exhaust Gas
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow these safety tips: Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or...
Page 75: Safety Checks You Should Make Inside The Vehicle
Safety Checks You Should Make Inside the Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision.
Page 76: Periodic Safety Checks You Should Make Outside The Vehicle
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Periodic Safety Checks You Should Make Outside the Vehicle Tires Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect the tread and sidewall for cuts and cracks.
Page 77 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors ......79 Inside Day/Night Mirror ....79 Automatic Dimming Mirror —...
Page 78 76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Recognition (VR) System — If Equipped ......111 Voice Recognition (VR) System Operation .
Page 79 Windshield Wipers And Washers ..131 Intermittent Wiper System ....131 Windshield Washers ....132 Tilt Steering Column .
Page 80 78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage ......152 Center Storage Compartment (40–20–40 Seat) —...
Page 81: Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 MIRRORS Inside Day/Night Mirror Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle). The mirror should be adjusted while set in the day position (toward the windshield).
Page 82: Automatic Dimming Mirror - If Equipped
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light next to the button will illuminate to indicate when the dimming feature is activated.
Page 83: Outside Mirrors Folding Feature
WARNING! Vehicles and other objects seen in a passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger side convex mirror.
Page 84: Heated Mirrors - If Equipped
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Select the left or right mirror using the top switch, then press one of the four arrows on the bottom switch to adjust the mirror. Once the mirror is adjusted, set the top switch to the center (off) position to prevent accidentally moving a mirror.
Page 85: Uconnect™ Phone - If Equipped
Trailer Towing Position NOTE: Fold the trailer towing mirrors rearward prior to entering an automated car wash. A small blindspot mirror is integrated onto the main mirror surface. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 Blindspot Mirror uconnect™ phone — IF EQUIPPED uconnect™...
Page 86 0.96 or higher. See the uconnect™ website for supported phones. For uconnect™ customer support, visit the following websites: • www.chrysler.com/uconnect • www.dodge.com/uconnect • www.jeep.com/uconnect • or call 1–877–855–8400 uconnect™ phone allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle and enables you to mute the system’s...
Page 87: Operation
WARNING! Any voice commanded system should be used only in safe driving conditions following local laws and phone use. All attention should be kept on the roadway ahead. Failure to do so may result in an accident causing serious injury or death. Phone Button Depending on the vehicle options, either the radio or the mirror will contain the two control...
Page 88 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE menu structure. Voice commands are required after most uconnect™ phone prompts. You will be prompted for a specific command and then guided through the available options. • Prior to giving a voice command, one must wait for the beep, which follows the Ready prompt or another prompt.
Page 89 Cancel Command At any prompt, after the beep, you can say Cancel and you will be returned to the main menu. However, in a few instances the system will take you back to the previous menu. Pair (Link) uconnect™ phone to a Cellular Phone To begin using your uconnect™...
Page 90 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE phone to use if multiple cellular phones are in the vehicle at the same time. For example, if priority three and priority five phones are present in the vehicle, the uconnect™ phone will use the priority three cellular phone when you make a call.
Page 91 • The uconnect™ system will confirm the name and then dial the corresponding phone number, which may appear in the display of certain radios. Add Names to Your uconnect™ Phonebook NOTE: Adding names to the uconnect™ phonebook is recommended when the vehicle is not in motion. •...
Page 92 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phonebook Download – Automatic Phonebook Transfer From Cellular Phone If equipped and specifically supported by your phone, uconnect™ phone automatically downloads names (text names) and number entries from the cellular phone’s phonebook. Specific Bluetooth Phones with Phone Book Access Profile may support this feature.
Page 93 Phonebook Download — Single Entry If equipped and supported by your phone, uconnect™ phone allows the user to download entries from their phone via Bluetooth . To use this feature, press the button and say “Phonebook Download.” The system prompts, “Ready to accept “V” card entry via Bluetooth …”...
Page 94 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You will then be asked for the name of the phonebook entry that you wish to edit. • Next, choose the number designation (home, work, cellular, or pager) that you wish to edit. •...
Page 95 • After you enter the name, the uconnect™ phone will ask you which designation you wish to delete: home, work, cellular, pager, or all. Say the designation you wish to delete. • Note that only the phonebook entry in the current language is deleted.
Page 96: Phone Call Features
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The uconnect™ phone will then prompt you as to the number designation you wish to call. • The selected number will be dialed. Phone Call Features The following features can be accessed through the uconnect™...
Page 97 progress. To go back to the first call, refer to Toggling Between Calls in this section. To combine two calls, refer to Conference Call in this section. Place/Retrieve a Call From Hold To put a call on hold, press the a single beep.
Page 98: Uconnect™ Phone Features
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the Ready prompt and the following beep, say Redial. • The uconnect™ phone will call the last number that was dialed from your cellular phone. NOTE: This may not be the last number dialed from the uconnect™...
Page 99 After selecting one of the languages, all prompts and voice commands will be in that language. NOTE: After every uconnect™ phone language change operation, only the language-specific 32-name phone- book is usable. The paired phone name is not language- specific and usable across all languages. Emergency Assistance If you are in an emergency and the cellular phone is reachable:...
Page 100 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Your phone must be turned on and paired to the uconnect™ phone to allow use of this vehicle feature in emergency situations, when the cellular phone has network coverage and stays paired to the uconnect™ phone.
Page 101 Working with Automated Systems This method is used in instances where one generally has to press numbers on the cellular phone keypad while navigating through an automated telephone system. You can use your uconnect™ phone to access a voice mail system or an automated service, such as a paging service or automated customer service line.
Page 102 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Barge In - Overriding Prompts The “Voice Recognition” button can be used when you wish to skip part of a prompt and issue your voice recognition command immediately. For example, if a prompt is asking Would you like to pair a phone, clear a..., you could press the button and say, Pair a Phone to select that option without having to listen to...
Page 103: Advanced Phone Connectivity
NOTE: Certain brands of cellular phones do not send the dial ring to the uconnect™ phone to play it on the vehicle audio system, so you will not hear it. Under this situation, after successfully dialing a number the user may feel that the call did not go through even though the call is in progress.
Page 104 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE List Paired Cellular Phone Names • Press the button to begin. • After the “Ready” prompt and the following beep, say “Setup Phone Pairing.” • When prompted, say List Phones. • The uconnect™ phone will play the phone names of all paired cellular phones in order from the highest to the lowest priority.
Page 105: Things You Should Know About Your Uconnect™ Phone
• You can also press the button at any time while the list is being played, and then choose the phone you wish to delete. Things You Should Know About Your uconnect™ phone uconnect™ phone Tutorial To hear a brief tutorial of the system features, press the button and say “uconnect™...
Page 106 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Always wait for the beep before speaking. • Speak normally, without pausing, just as you would speak to a person sitting a few feet/meters away from you. • Make sure that no one other than you is speaking during a voice recognition period.
Page 107 • Even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported. • In a convertible vehicle, system performance may be compromised with the convertible top down. Phone Far End Audio Performance •...
Page 108 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 109 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107...
Page 110 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 111 Voice Commands Primary Alternate(s) zero three four five seven eight nine star (*) plus (+) pound (#) add location UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Voice Commands Primary Alternate(s) call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol...
Page 112 110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Primary Alternate(s) language list names list phones mobile mute mute off new entry pager pair a phone phone pairing pairing phonebook phone book previous record again redial Voice Commands Primary Alternate(s) return to main menu return or main menu select phone...
Page 113: General Information
General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Page 114 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Any voice commanded system should be used only in safe driving conditions following local laws and phone use. All attention should be kept on the roadway ahead. Failure to do so may result in an accident causing serious injury or death.
Page 115: Commands
At any point, if the system does not recognize one of your commands, you will be prompted to repeat it. To hear the first available Menu, press the and say “Help” or “Main Menu”. Commands The Voice Recognition (VR) system understands two types of commands.
Page 116 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • “Radio Menu” (to switch to the radio menu) • “Main Menu” (to switch to the main menu) Radio FM To switch to the FM band, say “FM” or “Radio FM”. In this mode, you may say the following commands: •...
Page 117 Disc To switch to the disc mode, say “Disc”. In this mode, you may say the following commands: • “Track” (#) (to change the track) • “Next Track” (to play the next track) • “Previous Track” (to play the previous track) •...
Page 118: Voice Training
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • “Language Dutch” • “Language Italian” • “Language English” • “Language French” • “Language Spanish” • “Tutorial” • “Voice Training” NOTE: Keep in mind that you have to press the button first and wait for the beep before speaking the “Barge In”...
Page 119: Manual Seat Adjuster - If Equipped
WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
Page 120: Reclining Seats
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Only adjust a seat while the vehicle is parked.
Page 121: Adjustable Head Restraints
WARNING! You can be seriously, even fatally, injured riding in a seat with the seatback reclined. Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. If you ride in this position, the shoulder harness will no longer be restraining you.
Page 122: Manual Rotary Lumbar Support Adjustment - If Equipped
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Rotary Lumbar Support Adjustment — If Equipped Rotating the lumbar control knob on the left-side of the driver’s seatback and on the right side of the passenger’s seatback increases or decreases the lumbar (lower back) support.
Page 123 CAUTION! DO NOT place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path.
Page 124: Heated Seats - If Equipped
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The angle, or tilting, of the seat cushion can be adjusted using the two toggle switches. Use the forward switch to raise or lower the front seat cushion. Use the rear switch to raise or lower the rear of the seat cushion. Tilt Adjustment Heated Seats —...
Page 125 switch indicate the level of heat in use. Two indicator lights will illuminate for High, one for Low, and none for Off. Press the switch once to select High-level heat- ing. Press the switch a second time to select Low-level heating. Press the switch a third time to shut the heating elements Off.
Page 126: To Open And Close The Hood
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. 1. Pull the hood release lever located below the steering wheel at the base of the instrument panel. Hood Release Lever 2.
Page 127: Lights
CAUTION! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage. WARNING! Be sure the hood is fully latched before driving your vehicle.
Page 128: Interior Lights
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Lights Courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the switch) is rotated to the upward detent position, or if equipped, when the UN- LOCK button is pressed on the Remote Keyless Entry (RKE) transmitter.
Page 129: Battery Saver
Battery Saver To protect the life of your vehicle’s battery, load shedding is provided for both the interior and exterior lights. If the ignition is OFF and any door is left ajar for 10 minutes or the dimmer control is rotated upwards for 10 minutes, the interior lights will automatically turn off.
Page 130: Headlights, Parking Lights And Panel Lights
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights, Parking Lights and Panel Lights When the headlight switch is rotated to the first position, the parking lights, tail lights, side marker lights, license plate light and instrument panel lights are all turned on. The headlights will turn on when the switch is rotated to the second position.
Page 131: Lights-On Reminder
brake is applied the Daytime Running Lights (DRL) will turn OFF. Also, if a turn signal is activated, the DRL lamp on the same side of the vehicle will turn off for the duration of the turn signal activation. Once the turn signal is no longer active, the DRL lamp will illuminate.
Page 132 130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE You can signal a lane change by moving the lever partially up or down. Turn Signal Lever Lane Change Assist Tap the lever up or down once and the turn signal (left or right) will flash three times then automatically turn off.
Page 133: Windshield Wipers And Washers
High Beam/Low Beam WINDSHIELD WIPERS AND WASHERS The wipers and washers are operated by a switch in the multifunction lever. Turn the end of the handle to select the desired wiper speed. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Windshield Wiper/Washer Switch Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle,...
Page 134: Windshield Washers
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The delay interval decreases as you rotate the knob until it enters the low continual speed position. The delay can be regulated from a maximum of about 15 seconds between cycles, to a cycle every two seconds. The delay intervals will double in duration when the vehicle speed is 10 mph (16 km/h) or less.
Page 135 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your ve- hicle.
Page 136: Electronic Speed Control - If Equipped
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, Electronic Speed Control takes over accel- erator operation at speeds greater than 25 mph (40 km/h). The controls are mounted on the steering wheel. Electronic Speed Control Buttons 1 —...
Page 137: To Deactivate
To Deactivate A soft tap on the brake pedal, normal braking, clutch pressure while slowing the vehicle, or pressing the CAN- CEL button will deactivate the Electronic Speed Control without erasing the memory. Pushing the ON/OFF but- ton to the OFF position or turning off the ignition erases the memory.
Page 138: To Accelerate For Passing
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate for Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. NOTE: When driving uphill, at elevations above 2,000 ft (610 m), or when the vehicle is heavily loaded (especially when towing) the vehicle may slow below the SET speed.
Page 139: Overhead Console With Electronic Vehicle Information Center (Evic)
OVERHEAD CONSOLE WITH ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) The overhead console contains dome/reading lights, and an Electronic Vehicle Information Center (EVIC). Dome/Reading Lights Located in the overhead console are two dome/reading lights. The dome/reading lights illuminate when a door is opened or when the interior lights are turned on by rotating the dimmer control located on the headlight switch.
Page 140: Electronic Vehicle Information Center (Evic) - If Equipped
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electronic Vehicle Information Center (EVIC) — If Equipped Overhead Console With EVIC Pressing the MENU button will change the display to one of the following features: Trip Functions Pressing the STEP button allows you to scroll through one of the following Trip Function features: •...
Page 141 • AVG. MPG – Shows the average fuel economy since the last reset. When the fuel economy is reset, the display will show dashes for two seconds. Then the history information will be erased, and the averaging will continue from the last fuel average reading before the reset.
Page 142 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • PERSONAL SETTINGS NOT AVAILABLE – Vehicle not in PARK or Vehicle in Motion (Manual Transmis- sion Only) • LEFT/RIGHT FRONT DOOR AJAR (one or more, with a single chime if speed is above 1 mph (1.6 km/h) •...
Page 143 scheduled oil change interval. The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style. NOTE: When prompted by the Engine Oil Change Indicator System, the engine oil and filter must be changed.
Page 144 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cooler, and cleaning of the EGR Valve. The procedure for clearing and resetting the “Perform Service” indicator message is located in the appropriate service informa- tion. Refer to the “Maintenance Schedule” in Section 8 for the proper emission maintenance intervals.
Page 145 • “RKE UNLOCK DRV DR 1st” – When DRV DR 1st is selected, only the driver’s door will unlock on the first press of the remote keyless entry UNLOCK button. When Driver Door 1st Press is selected, you must press the remote keyless entry UNLOCK button twice to unlock the passenger’s doors.
Page 146 144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • “KEY OFF POWER DELAY > OFF” – When this feature is selected, the power window switches, radio, hands–free system (if equipped), and power outlets will remain active for up to 10 minutes after the ignition switch is turned OFF.
Page 147: Compass/Temperature Button
Compass/Temperature Button Pressing the Compass/Temperature button will return the display to the normal compass/ temperature display. NOTE: Temperature accuracy can be affected from heat soak. For best accuracy, the vehicle should be driven at a speed greater than 25 mph (40 km/h) for several min- utes.
Page 148 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Compass Variance Compass Variance is the difference between magnetic North and Geographic North. In some areas of the country, the difference between magnetic and geographic North is great enough to cause the compass to give false readings.
Page 149: Electrical Power Outlets
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 4. Press and release RESET button until the proper variance zone is selected according to the map. 5. Press and release the Compass button to exit. ELECTRICAL POWER OUTLETS The auxiliary electrical power outlet can provide power for in-cab accessories designed for use with the standard “cigar lighter”...
Page 150 148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE There is also a power outlet located on the rear of the center console (if equipped with bucket seats). Rear Power Outlet The power outlet(s) has/have a fused direct feed from the battery so it/they receive power whether the ignition is ON or OFF.
Page 151 WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle.
Page 152: Cigar Lighter And Ash Receiver
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CIGAR LIGHTER AND ASH RECEIVER The removable ash receiver is located in the instrument panel cupholder tray. The cigar lighter is located on the instrument panel, above and to the left of the ash receiver. As a child safety precaution, the lighter only operates with the ignition switch ON.
Page 153 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 door handle, on the front surface. Each opening in the cupholder is adjustable and will hold cups and mugs of various sizes. To secure the cup, place the cup to be held into one of the cup wells and then push the cupholder arm toward the cup until it is held stable.
Page 154: Front Instrument Panel Cupholders (Bucket Seats)
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Instrument Panel Cupholders (Bucket Seats) If your vehicle is equipped with bucket seats there are three cupholders located on the front of the center console. Cupholders Bucket Seat Rear Cupholder (Quad Cab ) — If Equipped Quad Cab vehicles may be equipped with a rear cup- holder that consists of two cupwells for rear passenger convenience.
Page 155 Center Storage Compartment UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 WARNING! • This armrest is not a seat. Anyone seated on the armrest could be seriously injured during vehicle operation, or an accident. Only use the center seating position when the armrest is fully upright. •...
Page 156: Center Storage Compartment (Bucket Seats) - If Equipped
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
Page 157 Center Storage Compartment UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 WARNING! • This armrest is not a seat. Anyone seated on the armrest could be seriously injured during vehicle operation, or an accident. Only use the center seating position when the armrest is fully upright. •...
Page 158: Storage And Seats (Quad Cab Models)
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
Page 159: Center Storage Compartment Plastic Grocery Bag Retainers
Plastic Grocery Bag Retainers Retainer hooks which will hold plastic grocery bag handles are built into the back panel of the cab, behind the rear seat. Grocery Bag Hooks UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 FOLD FLAT LOAD FLOOR — IF EQUIPPED Quad Cab models with a 60/40 rear seat may be equipped with a folding load floor.
Page 160 158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Unfolding the Load Floor 1. Lift the 60/40 seat cushion(s) to the upward position. Load Floor In Open Position 3. Reverse the procedure to store the load floor. Unfolding The Load Floor 2. Grasp the knob on the load floor and lift the knob until the load floor unfolds into position.
Page 161 Positioning the Load Floor for Storage Access Under the Seat 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Unsnap the securing snap located at either side of the load floor. 3. Lift the load floor up to access storage under the load floor.
Page 163: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....163 Instrument Cluster ....164 6.7L Diesel Engine .
Page 164 162 UNDERSTANDING YOUR INSTRUMENT PANEL uconnect™ studios (Satellite Radio) — If Equipped ......186 System Activation ....186 Electronic Serial Number/Sirius Identification Number (ESN/SID) .
Page 165: Instrument Panel Features
INSTRUMENT PANEL FEATURES 1 — Headlight Switch 6 — Passenger Airbag* 2 — Air Outlets 7 — Glove Box 3 — Instrument Cluster 8 — Passenger Airbag On/Off Switch* 4 — Climate Controls 9 — Power Outlet 5 — Radio 10 —...
Page 166: Instrument Cluster
164 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER 6.7L Diesel Engine...
Page 167: Instrument Cluster Description
INSTRUMENT CLUSTER DESCRIPTION 1. Check Gages Warning Light This light will illuminate when the voltmeter, engine oil pressure, or engine coolant temperature gauge indicates a reading either too high or too low. Examine the gauges carefully, and follow the instructions contained below for each indicated problem.
Page 168 166 UNDERSTANDING YOUR INSTRUMENT PANEL • The cycling action will cause temporary dimming of the headlights, interior lights, and also a noticeable reduction in blower motor speed. 3. Turn Signal Indicator Light The arrows will flash with the exterior turn signals when the turn signal lever is operated.
Page 169 8. Speedometer The speedometer shows the vehicle speed in miles per hour (mph) and/or kilometers per hour (km/h). 9. Oil Pressure Gauge The pointer should always indicate some oil pres- sure when the engine is running. A continuous high or low reading, under normal driving conditions, may indicate a lubrication system malfunction.
Page 170 168 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Do not leave your vehicle unattended with the en- gine running, as you would not be able to react to the temperature indicator if the engine overheats. NOTE: • Engine idle speed will automatically increase to 1,000 RPM at elevated coolant temperatures to improve engine cooling.
Page 171 cannot do so, then the odometer must be set at zero, and a sticker must be placed in the door jamb stating what the mileage was before the repair or service. It is a good idea for you to make a record of the odometer reading before the repair/service, so that you can be sure that it is properly reset, or that the door jamb sticker is accurate if the odometer must be reset at zero.
Page 172 170 UNDERSTANDING YOUR INSTRUMENT PANEL service is required. Refer to “Overhead Console with Electronic Vehicle Information Center (EVIC)” in Sec- tion 3 for more information. 16. Front Fog Light Indicator Light — If Equipped This indicator will illuminate when the front fog lights are on.
Page 173 WARNING! A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants or wood or cardboard, etc. This could result in death or serious injury to the driver, occu- pants or others.
Page 174 172 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The light may flash momentarily during sharp cornering maneuvers, which change fluid level condi- tions. The vehicle should have service performed, and the brake fluid level checked. If brake failure is indicated, immediate repair is neces- sary.
Page 175 19. Anti-Lock Brake (ABS) Warning Light This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If the “ABS Warning Light” remains on or turns on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required.
Page 176 174 UNDERSTANDING YOUR INSTRUMENT PANEL 22. SERV 4WD Indicator Light The “4WD” indicator will be illuminated whenever the four-wheel drive mode is en- gaged on either the manual or electric shift four-wheel drive systems. The “SERV 4WD Indicator Light” monitors the electronic shift four-wheel drive system.
Page 177 overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale.
Page 178 176 UNDERSTANDING YOUR INSTRUMENT PANEL Tire Light Load Inflation Switch – If Equipped The tire light load inflation switch allows you to choose between “Light Load” vehicle conditions and “Max Load” vehicle conditions, tire pressures, and related TPMS warning levels. The switch is located on the instrument panel, below the climate control panel.
Page 179: Electronic Digital Clock
engine starting procedure for proper engine starting and operating. Wait until the “Wait To Start Light” turns OFF, then start the vehicle. NOTE: The “Wait To Start Light” may not illuminate if the intake manifold temperature is warm enough. 27. Odometer/Trip Odometer Button Press this button to toggle between the odometer and the trip odometer display.
Page 180: Clock Setting Procedure
178 UNDERSTANDING YOUR INSTRUMENT PANEL When the ignition switch is in the OFF position, or when the radio frequency is being displayed, time keeping is accurately maintained. On the RAQ radio the time button alternates the location of the time and frequency on the display. On the REF only one of the two, time or frequency, is displayed at a time.
Page 181: Operating Instructions - Radio Mode
Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOL control to turn the radio ON. Push the ON/VOL a second time to turn OFF the radio. Electronic Volume Control The electronic volume control turns continuously (360–...
Page 182 180 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: In Hands-Free Phone (if equipped) mode, the MUTE button mutes the microphone. SCAN Button (Radio Mode) Pressing the SCAN button causes the tuner to search for the next listenable station in either, AM, FM, or Satellite (if equipped) frequencies, pausing for five seconds at each listenable station before continuing to the next.
Page 183 TUNE Control (Radio Mode) Turn the rotary TUNE control clockwise to increase or counterclockwise to decrease the frequency. AM/FM Button (Radio Mode) Press the button to select AM or FM modes. Setting the Tone, Balance, and Fade Press the rotary TUNE control, and “BASS” will display. Turn the TUNE control to the right or left to increase or decrease the Bass tones.
Page 184: Operating Instructions - Cd Mode
182 UNDERSTANDING YOUR INSTRUMENT PANEL selected within five seconds after pressing the SET but- ton, the station will continue to play but will not be stored into pushbutton memory. You may add a second station to each pushbutton by repeating the above procedure with this exception: Press the SET button twice and “SET 2”...
Page 185 • If you insert a disc with the ignition ON and the radio OFF, the CD will automatically be pulled into the CD player. • This radio does not play discs with MP3 tracks. SEEK Button (CD Mode) Press the right side of the SEEK button for the next track on the CD.
Page 186: Operating Instructions - Auxiliary Mode
184 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the FF button to fast forward through the tracks. Release the FF button to stop the fast forward feature. If the RW button is pressed, the current track will reverse to the beginning of the track and begin playing. RND/SET Button (Random Play Button) (CD Mode) Press this button while the CD is playing to activate...
Page 187: Operating Instructions - Uconnect™ Phone - If Equipped
second time and the sound from the speakers will return. Rotating the volume control or turning the ignition OFF/ON will also return the sound from the speakers. SCAN Button (Auxiliary Mode) No function. EJECT Button (Auxiliary Mode) No function. PSCAN Button (Auxiliary Mode) No function.
Page 188: System Activation
186 UNDERSTANDING YOUR INSTRUMENT PANEL uconnect™ studios (SATELLITE RADIO) — IF EQUIPPED Satellite radio uses direct satellite to receiver broadcast- ing technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius Satellite Radio. This service offers over 130 channels of music, sports, news, entertainment, and programming for chil- dren, directly from its satellites and broadcasting studios.
Page 189: Selecting Uconnect™ Studios (Satellite) Mode
UP button until all 12 ESN/SID digits display. The SEEK DOWN will page down until the first four digits display. The radio will exit the ESN/SID mode when any other button is pushed, the ignition is turned OFF, or five minutes have passed since any button was pushed.
Page 190: Using The Pty (Program Type) Button - If Equipped
188 UNDERSTANDING YOUR INSTRUMENT PANEL Using The PTY (Program Type) Button — If Equipped Follow the PTY button instructions that apply to your radio. PTY Button SCAN When the desired program type is obtained, press the SCAN button within five seconds. The radio will play seven seconds of the selected channel before moving to the next channel of the selected program type.
Page 191: Reception Quality
Reception Quality Satellite reception may be interrupted due to one of the following reasons: • The vehicle is parked in an underground parking structure or under a physical obstacle. • Dense tree coverage may interrupt reception. • Driving under wide bridges or along tall buildings can cause intermittent reception.
Page 192: Radio Operation
190 UNDERSTANDING YOUR INSTRUMENT PANEL The left-hand control is a rocker type switch with a push button in the center. The function of the left-hand control is different, depending on which mode you are in. The following describes the left-hand control operation in each mode.
Page 193: Radio Operation And Cellular Phones
6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may become too high. NOTE: If you experience difficulty in playing a particu- lar disc, it may be damaged (i.e., scratched, reflective coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding.
Page 194: Heater Only - If Equipped
192 UNDERSTANDING YOUR INSTRUMENT PANEL Heater Only — If Equipped Manual Heating Controls The mode control (at the right of the control panel) can be set in any of the following positions: NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes.
Page 195 Recirculation Modes (Panel or Bi-Level) Select the recirculation modes when the outside air contains smoke or odors. This feature allows for recircu- lation of interior air only. Air flows through the panel outlets in this mode. Air flows through the panel only or through both the panel and floor vents depending on the selected mode (panel vs bi-level).
Page 196: Air Conditioning And Heating - If Equipped
194 UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control The rotary knob at the center of the control panel controls the temperature of the interior air. You can choose your degree of comfort by rotating the knob. The coldest temperature setting is to the extreme left (blue region) and the warmest setting is to the extreme right (red region) of the rotation.
Page 197 Air Conditioning Operation To turn on the air conditioning, set the fan control at any speed and press the snowflake button located at the right of the control panel. Conditioned air will be directed through the outlets selected by the mode control. A light in the snowflake button shows that the air conditioning is on.
Page 198 196 UNDERSTANDING YOUR INSTRUMENT PANEL both the panel and floor vents depending on the selected mode (panel vs bi-level). NOTE: Selecting a “Recirculation Mode” mode does not necessarily consume more fuel than normal A/C mode. Panel Outside air flows through the outlets located in the instrument panel.
Page 199 Temperature Control The rotary knob at the center of the control panel controls the temperature of the interior air. You can choose your degree of comfort by rotating the knob. The coldest temperature setting is to the extreme left (blue region) and the warmest setting is to the extreme right (red region) of the rotation.
Page 200: Operating Tips
198 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips Fast Cooldown For a fast cooldown, turn the blower fan rotary knob to the extreme right position, turn the mode control to the panel fresh position, press the snowflake button to turn on the air conditioning, and drive with the windows open for the first few minutes.
Page 201 Regular cleaning of the inside of the windows with a non-filming cleaning solution (vinegar and water works very well) will help prevent contaminates (cigarette smoke, perfumes, etc.) from sticking to the windows. Contaminates increase the rate of window fogging. Summer Operation Air conditioned vehicles must be protected with a high quality antifreeze coolant during summer to provide proper corrosion protection and to raise the boiling point...
Page 202: Operating Tips Chart
200 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips Chart...
Page 203: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ....205 Manual Transmission – If Equipped ..205 Automatic Transmission –...
Page 204 202 STARTING AND OPERATING Engine Block Heater — If Equipped ..218 Block Heater Usage ....218 Diesel Exhaust Brake (Engine Braking) .
Page 205 Power Steering ..... . . 241 Power Steering Fluid Check ... . . 242 Parking Brake .
Page 206 204 STARTING AND OPERATING Adding Fuel ......272 Fuel Filler Cap (Gas Cap) ....272 Avoid Using Contaminated Fuel .
Page 207: Starting Procedures
STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. The starter should not be operated for more than 15- second intervals. Waiting a few minutes between such intervals will protect the starter from overheating. WARNING! Do not leave children or animals inside parked vehicles in hot weather.
Page 208: Normal Starting Procedure - Engine Manifold Air Temperature Above 66°F (19°C)
206 STARTING AND OPERATING • A 12 Volt heater built into the fuel filter housing aids in preventing fuel gelling. It is controlled by a built-in thermostat. • A heated intake air system both improves engine starting and reduces the amount of white smoke generated by a warming engine.
Page 209: Starting Procedure - Engine Manifold Air
6. Check to see that there is oil pressure. 7. Release the parking brake. Starting Procedure – Engine Manifold Air Temperature Below 66°F (19°C) NOTE: The temperature displayed on the overhead console (if equipped) does not necessarily reflect the engine manifold air temperature. When engine tempera- tures fall below 66°F (19°C) the “Wait To Start Light”...
Page 210: Starting Procedure - Engine Manifold Air Temperature Below 0°F (-18°C)
208 STARTING AND OPERATING 3. After engine start-up, check to see that there is oil pressure. 4. Allow the engine to idle about three minutes until the manifold heaters have completed the post-heat cycle. 5. Release the parking brake and drive. NOTE: •...
Page 211 NOTE: Excessive white smoke and poor engine perfor- mance will result if manifold heaters are not recycled. 2. Heat generated by the manifold heaters dissipates rapidly in a cold engine. If more than two minutes pass between the time the “Wait To Start Light” turns off and the engine is started, recycle the manifold heaters by turning the ignition OFF for at least five seconds and then back ON.
Page 212: Starting Fluids
210 STARTING AND OPERATING Starting Fluids WARNING! Starting fluids or flammable liquids are never to be used in the Cummins diesel engine (see Warning label). Never pour diesel fuel, flammable liquid, starting fluids (ether) into the air cleaner canister, air intake piping, or turbocharger inlet in an attempt to start the vehicle.
Page 213: Cold Weather Precautions
engine control module. Post-heat operation can run for several minutes, and then the electrical system and voltmeter needle will stabilize. • The cycling action will cause temporary dimming of the headlamps, interior lamps, and also a noticeable reduction in blower motor speed. Cold Weather Precautions Operation in ambient temperature below 32°F (0°C) may require special considerations.
Page 214 212 STARTING AND OPERATING • The engine requires the use of “Ultra Low Sulfur Diesel Fuel”. Use of incorrect fuel could result in engine and exhaust system damage. Refer to” Starting and Operating/Fuel Requirements” in this manual for more information. Engine Oil Usage Refer to “Maintaining Your Vehicle/Maintenance Proce- dures”...
Page 215: Engine Idling
Your vehicle is equipped with a turbo speed limiter, this feature limits the engine speed to 1,200 RPM when engine coolant temperatures are below 70°F (21°C). This feature is designed to protect the turbo charger from damage and will only operate in PARK or NEUTRAL. If temperatures are below 32°F (0°C), operate the engine at moderate speeds for five minutes before full loads are applied.
Page 216: Stopping The Engine
214 STARTING AND OPERATING NOTE: For EVIC messages related to the vehicle’s exhaust system, refer to “Maintaining Your Vehicle/ Maintenance Procedures/Intervention Strategy — EVIC Message Process Flow” in this manual. Idle-Up Feature — Automatic Transmission Only The optional driver-controlled high idle speed will help increase cylinder temperatures and provide additional cab heat, however, may still cause the exhaust aftertreat- ment system to not properly regenerate.
Page 217 NOTE: • During engine shut down on vehicles equipped with manual transmissions, it is normal for the diesel engine to resonate heavily for a moment during engine shut off. When the engine is connected to a manual transmission, this resonance causes load gear rattle from the transmission.
Page 218: Engine Speed Control
216 STARTING AND OPERATING Engine Speed Control CAUTION! Prevent overspeeding the engine going downhill. When descending steep grades, use a combination of gears and service brakes to control vehicle/engine speed. Overspeed can cause severe engine damage. Operating Precautions Avoid Overheating The Engine The temperature of the engine coolant (antifreeze) (a mixture of 50% ethylene-glycol and 50% water) must not exceed the normal range of the temperature gauge 240°F...
Page 219 • Up Steep Hills — Select a lower transmission gear, but try and keep the torque converter clutch engaged. • Air Conditioning — Turn it off temporarily. Do Not Operate The Engine With Low Oil Pressure When the engine is at normal operating temperature, the minimum oil pressures required are: Idle 700 to 800 RPM .
Page 220: Block Heater Usage
218 STARTING AND OPERATING ENGINE BLOCK HEATER — IF EQUIPPED The engine block heater warms engine coolant and permits quicker starts in cold weather. Connect the heater cord to a ground-fault interrupter protected 110–115 Volt AC electrical outlet with a grounded, three-wire exten- sion cord.
Page 221 Exhaust Brake Switch Once the switch is in the ON position and the vehicle is moving faster than 5 mph (8 km/h); the exhaust brake will automatically operate when the driver removes pressure from the accelerator pedal. Exhaust braking is most effective when the engine RPM is higher.
Page 222: Automatic Transmission - If Equipped
220 STARTING AND OPERATING The purpose of the exhaust brake (engine braking) fea- ture is to supply negative (braking) torque to the engine. Typically, the engine braking is used for, but not limited to, vehicle towing applications where vehicle braking can be achieved by the internal engine power, thereby spar- ing the mechanical brakes of the vehicle.
Page 223: Automatic Transmission (Six-Speed As68Rc)
CAUTION! (Continued) • Before shifting into any gear, make sure your foot is firmly on the brake pedal. WARNING! It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed.
Page 224 222 STARTING AND OPERATING then place the shift lever in PARK position. On four- wheel drive vehicles be sure that the transfer case is in a drive position! WARNING! • Never use the PARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage.
Page 225 DRIVE This position provides all forward gears, including fourth gear direct and fifth or sixth (if equipped) gear overdrive (refer to Overdrive Operation in this section). Use this range for most city and highway driving. THIRD Use this position for driving in slight heavy city traffic or on mountain roads where more precise speed control is desirable.
Page 226 224 STARTING AND OPERATING • the engine coolant has reached normal operating tem- perature; • vehicle speed is above approximately 38 mph (61 km/h) for fifth gear and 50 mph (80 km/h) for sixth gear; • the “TOW HAUL O/D OFF” switch has not been activated;...
Page 227 When To Use “TOW HAUL” and “O/D OFF” Modes When driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting oc- curs, press the “TOW HAUL O/D OFF” switch once to select TOW HAUL. This will improve performance and reduce the potential for transmission overheating or failure due to excessive shifting.
Page 228 226 STARTING AND OPERATING WARNING! Do not use the TOW HAUL feature when driving in icy or slippery conditions as the increased engine braking can cause the rear wheels to slide and the vehicle to swing around with the possible loss of vehicle control, which may cause an accident possi- bly resulting in personal injury or death.
Page 229: Manual Transmission - If Equipped
• If the vehicle has not been driven in several days, the first few seconds of operation after shifting the trans- mission into gear may seem sluggish. This is due to the fluid partially draining from the torque converter into the transmission.
Page 230: Shifting
228 STARTING AND OPERATING Shifting Shift Pattern Truck models with manual transmission are equipped with a clutch interlocking ignition system. The clutch pedal must be fully pressed to start the vehicle. Fully press the clutch pedal before shifting gears. As you release the clutch pedal, lightly press the accelerator pedal.
Page 231: Downshifting
vehicle speeds listed for acceleration. When heavily loaded or pulling a trailer these recommended up-shift speeds may not apply. Maximum Recommended Up-shift Speeds Gear Selec- L to 2 2 to 3 3 to 4 tion Maxi- 7 mph 15 mph 25 mph Speed km/h)
Page 232: Reverse Shifting
230 STARTING AND OPERATING Maximum Recommended Downshift Speeds CAUTION! Failure to follow the recommended downshifting speeds may cause the engine to overspeed and/or damage the clutch disc even if the clutch pedal is pressed. Maximum Recommended Downshifting Speeds Gear Selec- 6 to 5 5 to 4 4 to 3...
Page 233: Four-Wheel Drive Operation - If Equipped
FOUR-WHEEL DRIVE OPERATION — IF EQUIPPED Manually Shifted Transfer Case Operating Information/Precautions The transfer case provides four mode positions. • Two-wheel drive high range (2H) • Four-wheel drive high range (4H) • Neutral (N) • Four-wheel drive low range (4L) This transfer case is intended to be driven in the 2H position for normal street and highway conditions such as dry, hard surfaced roads.
Page 234 232 STARTING AND OPERATING Proper operation of four-wheel drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference will adversely affect shifting and can cause damage to the transfer case. NOTE: Do not attempt to make a shift while only the front or rear wheels are spinning.
Page 235: Shifting Procedure - Manually Shifted Transfer Case
Four-Wheel Drive High Range - This range locks the front and rear driveshafts together forcing the front and rear wheels to rotate at the same speed. Additional traction for loose, slippery road surfaces only. Neutral - This range disengages the front and rear driveshafts from the powertrain.
Page 236: Transfer Case Position Indicator Light
234 STARTING AND OPERATING vehicle in motion, the transfer case will engage/ disengage faster if you momentarily release the accelera- tor pedal after completing the shift. Apply a constant force when shifting the transfer case lever. 2H or 4H ⇔ 4L With the vehicle rolling at 2 to 3 mph (3 to 5 km/h), shift the transmission into NEUTRAL.
Page 237: Stationary Mode
allow for an aftermarket upfit with a transmission driven PTO (power take off). The customer will have the ability to operate the PTO in either a “stationary” or “mobile” mode. The vehicles will be factory set to the “stationary” mode. In order to select the “mobile” mode an authorized dealership is required to modify the vehicle’s settings using their proprietary authorized dealer service tool.
Page 238: Mobile Mode
236 STARTING AND OPERATING To operate the PTO via a remote switch the customer must make sure the above conditions are met. It is vital for proper operation that the PTO and remote have been installed correctly, paying special attention to ensure the vehicle provided wiring has been connected properly.
Page 239: Power Take Off - Aftermarket Installation
PTO and pump requirements and additional vehicle information (wiring schematics, preset idle values, en- gine speed limits, and vehicle hardware and software requirements) please refer to the Dodge Body Builders Guide by accessing “www.dodge.com/bodybuilder” and choosing the appropriate links.
Page 240: Driving On Slippery Surfaces
238 STARTING AND OPERATING WARNING! On vehicles equipped with a limited-slip differential never run the engine with one rear wheel off the ground since the vehicle may drive through the rear wheel remaining on the ground. You could lose control of the vehicle. Care should be taken to avoid sudden accelerations when both rear wheels are on a slippery surface.
Page 241: Flowing/Rising Water
Flowing/Rising Water WARNING! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off). Flow- ing water can wear away the road or path’s surface and cause your vehicle to sink into deeper water. Furthermore, flowing and/or rising water can carry your vehicle away swiftly.
Page 242 240 STARTING AND OPERATING CAUTION! (Continued) • Driving through standing water may cause dam- age to your vehicle’s drivetrain components. Al- ways inspect your vehicle’s fluids (i.e., engine oil, transmission/transaxle, axle, etc.) for signs of con- tamination (i.e., fluid that is milky or foamy in appearance) after driving through standing water.
Page 243: Power Steering
POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible to steer your vehicle.
Page 244: Power Steering Fluid Check
242 STARTING AND OPERATING Power Steering Fluid Check Checking the power steering fluid level at a defined service interval is not required. The fluid should only be checked if a leak is suspected, abnormal noises are apparent, and/or the system is not functioning as antici- pated.
Page 245 NOTE: The “Brake Warning Light” will come on and flash to indicate that the parking brake is applied. You must be sure that the parking brake is fully applied before leaving the vehicle. Parking Brake Be sure the parking brake is firmly set when parked and the shift lever is in the PARK position.
Page 246: Brake System
244 STARTING AND OPERATING WARNING! (Continued) • Be sure the parking brake is fully disengaged before driving, failure to do so can lead to brake problems due to excessive heating of the rear brakes. When parking on a hill, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.
Page 247 WARNING! (Continued) • ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that af- forded by the condition of the vehicle brakes and tires or the traction afforded. •...
Page 248: Tire Safety Information
246 STARTING AND OPERATING ABS Warning Light The ABS includes an amber warning light, located in the instrument cluster. When the light is illuminated, the ABS is not functioning. The system reverts to standard non- anti-lock brakes. WARNING! Pumping of the anti-lock brakes will diminish their effectiveness and may lead to an accident.
Page 249 NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards.
Page 250 248 STARTING AND OPERATING Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm)
Page 251 Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
Page 252: Tire Identification Number (Tin)
250 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.
Page 253: Tire Loading And Tire Pressure
Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. Tire and Loading Information Placard Tire and Loading Information Placard STARTING AND OPERATING 251 This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry...
Page 254 252 STARTING AND OPERATING NOTE: Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded. For further information on GAWRs, vehicle loading, and trailer towing, refer to “Vehicle Loading” in this section. To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or...
Page 255 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle.
Page 256 254 STARTING AND OPERATING...
Page 257: Tires - General Information
WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 258: Tire Inflation Pressures
256 STARTING AND OPERATING WARNING! (Continued) • Unequal tire pressures from one side of the ve- hicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recom- mended cold tire inflation pressure.
Page 259 CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.”...
Page 260 258 STARTING AND OPERATING Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) during operation. DO NOT reduce this normal pressure build up or your tire pressure will be too low. Tire Inflation Pressure — 4500/5500 with Steel Carcass Ply Tires This type of tire utilizes steel cords in the sidewall.
Page 261 STARTING AND OPERATING 259 4500/5500 Tire Inflation...
Page 262 260 STARTING AND OPERATING When adjusting inflation pressure to a tire and wheel assembly mounted on a vehicle, use a Remote Mount Automatic Inflation Kit or see your authorized dealer. NOTE: Never attempt to re-inflate a tire and wheel assembly which has been run flat or is extremely under- inflated without first removing the tire from the wheel assembly for inspection.
Page 263: Radial Ply Tires
Radial Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident result- ing in serious injury or death. Always use radial ply tires in sets of four (or six, in case of trucks with dual rear wheels).
Page 264: Tread Wear Indicators
262 STARTING AND OPERATING Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. 1 — Worn Tire 2 — New Tire These indicators are molded into the bottom of the tread grooves.
Page 265: Replacement Tires
WARNING! Tires and spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have an accident resulting in serious injury or death. Keep dismounted tires in a cool, dry place with as little exposure to light as possible.
Page 266 264 STARTING AND OPERATING WARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle.
Page 267: Supplemental Tire Pressure Information - If Equipped
CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer read- ings. SUPPLEMENTAL TIRE PRESSURE INFORMATION — IF EQUIPPED A light load vehicle condition is defined as two passen- gers [150 lbs (68 kg) each] plus 200 lbs (91 kg) of cargo. Cold tire inflation pressures for a lightly loaded vehicle will be found on the face of the driver’s door.
Page 268 266 STARTING AND OPERATING CAUTION! (Continued) • Do not drive for a prolonged period on dry pave- ment. • Observe the tire chain manufacturer’s instructions on method of installation, operating speed, and conditions for usage. Always use the lower sug- gested operating speed of the chain manufacturer if different than the speed recommended by the manufacturer.
Page 269: Snow Tires
SNOW TIRES Snow tires should be of the same size and type construc- tion as the front tires. Consult the manufacturer of the snow tire to determine any maximum vehicle speed requirement associated with the tire. These tires should always be operated at the vehicle maximum capacity inflation pressures under any load condition.
Page 270: Dual Rear Wheels
268 STARTING AND OPERATING Refer to the “Maintenance Schedule” in Section 8 of this manual for the proper maintenance intervals. More fre- quent rotation is permissible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being performed.
Page 271 The tires used on dual wheel assemblies should be matched for wear to prevent overloading one tire in a set. To check if tires are even, lay a straight edge across all four tires. The straight edge should touch all the tires. CAUTION! 4500/5500 Dual Rear Tires have only one approved direction of rotation.
Page 272: Engine Runaway
270 STARTING AND OPERATING ENGINE RUNAWAY WARNING! In case of engine runaway due to flammable fumes from gasoline spills or turbocharger oil leaks being sucked into the engine, do the following to help avoid personal injury and/or vehicle damage: 1. Shut off engine ignition switch. 2.
Page 273: Fuel Specifications
WARNING! Do not use alcohol or gasoline as a fuel blending agent. They can be unstable under certain conditions and hazardous or explosive when mixed with diesel fuel. Diesel fuel is seldom completely free of water. To prevent fuel system trouble, drain the accumulated water from the fuel/water separator using the fuel/water separator drain provided.
Page 274: Fuel Filler Cap (Gas Cap)
272 STARTING AND OPERATING ADDING FUEL CAUTION! To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling. NOTE: • When the fuel nozzle “clicks” or shuts off, the fuel tank is full. • Tighten the gas cap until you hear a “clicking” sound. This is an indication that the gas cap is properly tightened.
Page 275: Avoid Using Contaminated Fuel
WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • Never add fuel to the vehicle when the engine is running. Avoid Using Contaminated Fuel Fuel that is contaminated by water or dirt can cause severe damage to the engine fuel system.
Page 276: Vehicle Loading
274 STARTING AND OPERATING VEHICLE LOADING Certification Label As required by National Highway Traffic Safety Admin- istration regulations, your vehicle has a certification label affixed to the driver’s side door or pillar. This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), Gross Axle Weight Rating (GAWR) front and rear, and Vehicle Identification Number (VIN).
Page 277 Tire Size The tire size on the Label represents the actual tire size on your vehicle. Replacement tires must be equal to the load capacity of this tire size. Rim Size This is the rim size that is appropriate for the tire size listed.
Page 278: Trailer Towing
276 STARTING AND OPERATING Improper weight distributions can have an adverse effect on the way your vehicle steers and handles and the way the brakes operate. CAUTION! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles.
Page 279 measure GTW is to put your fully loaded trailer on a vehicle scale. The entire weight of the trailer must be supported by the scale. Gross Combination Weight Rating (GCWR) The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination.
Page 280 278 STARTING AND OPERATING Trailer Sway Control The trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.
Page 281: Trailer Hitch Classification
Weight-distributing systems may not be compatible with surge brake couplers. Consult with your hitch and trailer manufacturer or an authorized recreational vehicle dealer for additional information. Fifth-Wheel Hitch The fifth-wheel hitch is a special high platform with a coupling that mounts over the rear axle of the tow vehicle in the truck bed.
Page 282: Trailer Towing Weights (Maximum Trailer Weight Ratings)
NOTE: For additional trailer towing information (maxi- mum trailer weight ratings) refer to the following website addresses: • http:// www.dodge.com/towing. • http:// www.dodge.ca (Canada). Trailer and Tongue Weight (4540 kg) Always load a trailer with 60% to 65% of the weight in the front of the trailer.
Page 283: Towing Requirements
Never exceed the maximum tongue weight stamped on your bumper or trailer hitch. Consider the following items when computing the weight on the rear axle of the vehicle: • The tongue weight of the trailer. • The weight of any other type of cargo or equipment put in or on your vehicle.
Page 284 282 STARTING AND OPERATING CAUTION! (Continued) • During the first 500 miles (805 km) of trailer towing, limit your speed to 50 mph (80 km/h). Perform the maintenance listed in Section 8 of this manual. When towing a trailer, never exceed the GAWR, or GCWR, ratings.
Page 285 WARNING! (Continued) • Vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle automatic transmission in PARK. With four-wheel drive ve- hicles, make sure the transfer case is not in NEU- TRAL.
Page 286 284 STARTING AND OPERATING − When replacing tires, refer to “Tires – General Infor- mation” in this section. Replacing tires with a higher load carrying capacity will not increase the vehicle’s GVWR and GAWR limits. Towing Requirements – Trailer Brakes −...
Page 287 If done improperly it may cause damage to the electrical system wiring and could result in serious or fatal injury. The following chart identifies the maximum electrical loads that the trailer tow output circuits are capable of supporting. “www.dodge.com/...
Page 288: Towing Tips
286 STARTING AND OPERATING Trailer Tow Additional Lamp Loads Output Maximum Additional Bulbs Al- Functions Current lowed. Example Only. Other bulb combinations can be used as long as maximum current is not Stop/Turn 2 #3157 bulbs for stop/ Left turn Stop/Turn 2 #3157 bulbs for stop/ Right...
Page 289: Snowplow
Tow/Haul – If Equipped To reduce potential for automatic transmission overheat- ing, turn the “TOW HAUL OD/OFF” feature ON when driving in hilly areas or shift the transmission to Drive position 2 on more severe grades. Electronic Speed Control – If Equipped −...
Page 290: Before Plowing
288 STARTING AND OPERATING Dodge Body Builders Guide. See your authorized dealer, installer or snowplow manufacturer for this information. There are unique electrical systems that must be con- nected to properly assure operator safety and prevent overloading vehicle systems. WARNING!
Page 291: Over The Road Operation With Snowplow
2. The total GVWR or the Front GAWR or the Rear GAWR should never be exceeded. 3. The snowplow prep packages are not available with the Sport Package. 4. Cargo capacity will be reduced by the addition of options or passengers, etc. The loaded vehicle weight, including the snowplow system, all aftermarket accessories, driver, passengers, options, and cargo, must not exceed either the Gross...
Page 292: Operating Tips
290 STARTING AND OPERATING Operating Tips Under ideal snow plowing conditions, 20 mph (32 km/h) should be maximum operating speed. The operator should be familiar with the area and surface to be cleaned. Reduce speed and use extreme caution when plowing unfamiliar areas or under poor visibility.
Page 293: Recreational Towing (Behind Motorhome, Etc.)
RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) CAUTION! Front or rear wheel lifts should not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when recreational towing. Recreational Towing – Two-Wheel Drive Models Recreational towing of two-wheel drive models is not allowed.
Page 294 292 STARTING AND OPERATING Recreational Towing Procedure — Manual Shift Transfer Case — If Equipped Use the following procedure to prepare your vehicle for recreational towing: CAUTION! It is necessary to follow these steps to be certain that the transfer case is fully in NEUTRAL before recre- ational towing to prevent damage to internal parts.
Page 295 CAUTION! Damage to the transmission may occur if the trans- mission is shifted into PARK with the transfer case in NEUTRAL and the engine running. With the transfer case in NEUTRAL ensure that the engine is OFF prior to shifting the transmission into PARK. Returning to Normal Operation —...
Page 296 294 STARTING AND OPERATING WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the NEUTRAL position without first fully engaging the parking brake. The transfer case NEUTRAL position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move, regardless of the transmission position.
Page 297: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....296 Jacking And Tire Changing ....297 3500 Models —...
Page 298: Hazard Warning Flasher
296 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The Hazard Warning flasher switch is mounted on the top of the steering column. Hazard Warning Flasher Switch Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.
Page 299: Jacking And Tire Changing
JACKING AND TIRE CHANGING WARNING! • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack.
Page 300: Preparations For Jacking
298 WHAT TO DO IN EMERGENCIES WARNING! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience abrupt stopping, rapid accelera- tion, or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury.
Page 301: Jacking Instructions
6. Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. NOTE: Passengers should not remain in the vehicle when the vehicle is being jacked. Jacking Instructions Instructions WARNING!
Page 302 300 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • If working on or near a roadway, be extremely careful of motor traffic. • To assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground.
Page 303 Front Jacking Locations When changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Securely place the jack under the sway bar bracket (unless both tires are flat on one side, then place jack under shock bracket) facing forward in vehicle.
Page 304 302 WHAT TO DO IN EMERGENCIES 4. By rotating the wheel wrench clockwise, raise the vehicle until the wheel just clears the surface. WARNING! Raising the vehicle higher than necessary can make the vehicle unstable and cause an accident. It could slip off the jack and hurt someone near it.
Page 305 8. Lower the jack to its fully closed position. If the jack will not lower by turning the dial (thumbwheel) by hand, it may be necessary to use the jack drive tube in order to lower the jack. Stow the replaced tire, jack, and tools as previously described.
Page 306 304 WHAT TO DO IN EMERGENCIES You must use the flat end of the lug wrench to pry off the wheel skins. Insert the flat tip completely and using a back and forth motion, loosen the wheel skin. Repeat this procedure around the tire until the skin pops off.
Page 307 WHAT TO DO IN EMERGENCIES 305 Dual wheel models require a special heavy-duty lug nut These dual rear wheels should be tightened as follows: tightening adapter (included with the vehicle) to cor- rectly tighten the lug nuts. Also, when it is necessary to remove and install dual rear wheels, use a proper vehicle lifting device.
Page 308 306 WHAT TO DO IN EMERGENCIES Tightening Pattern (10 Studs) 1. Tighten the wheel nuts in the numbered sequence to a snug fit. 2. Retighten the wheel nuts in the same sequence to the torques listed in the table. Go through the sequence a second time to verify that specific torque has been achieved.
Page 309: Hoisting
Disc Wheels Type Nut Cone Flanged To Stow The Flat Or Spare — If Equipped Refer to Upfitters Body Builders Guide for information on stowing your spare tire (if equipped). HOISTING A conventional floor jack may be used at the jacking locations.
Page 310 308 WHAT TO DO IN EMERGENCIES NOTE: Replacement batteries should both be of equal size to prevent damage to the vehicle’s charging system. Your vehicle is equipped with two 12-Volt batteries. If it becomes necessary to use a booster battery with jumper cables to start a vehicle’s engine because its batteries are discharged, the following procedure should be used: Set the parking brake and place an automatic transmis-...
Page 311 Attaching Booster Cables 1 — Discharged Battery 2 — Booster Battery 2. Connect one end of the other jumper cable to negative (-) post of booster battery. Connect the other end of the jumper cable to a good ground on the engine block of the WHAT TO DO IN EMERGENCIES 309 vehicle with the discharged battery.
Page 312: With Portable Starting Unit
310 WHAT TO DO IN EMERGENCIES 4. After the engine is started or if the engine fails to start, cables must be disconnected in the following order: a. Disconnect the negative cable at the engine ground. b. Disconnect the negative cable at the negative post on booster battery.
Page 313: Freeing A Stuck Vehicle
FREEING A STUCK VEHICLE If the vehicle becomes stuck in snow, sand, or mud, it can often be moved by a rocking motion. Move the shift lever rhythmically between DRIVE and REVERSE while ap- plying slight pressure to the accelerator. In general, the least amount of accelerator pedal pressure to maintain the rocking motion without spinning the wheels or racing the engine, is most effective.
Page 314: Towing A Disabled Vehicle
312 WHAT TO DO IN EMERGENCIES WARNING! • Chains are not recommended for freeing a stuck vehicle. Chains may break, causing serious injury or death. • Stand clear of vehicles when pulling with tow hooks. Tow straps and chains may break, causing serious injury.
Page 315: Two-Wheel Drive Vehicles
The manufacturer recommends towing with all wheels OFF the ground. Acceptable methods are to tow the vehicle on a flatbed or with one end of vehicle raised and the opposite end on a towing dolly. Two-Wheel Drive Vehicles Provided that the transmission is operable, tow with the transmission in NEUTRAL and the ignition key in the OFF position along with the front wheels raised and the rear wheels on the ground.
Page 317: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS Engine Compartment — 6.7L Diesel ..317 Replacement Parts ..... 318 Dealer Service .
Page 318 316 MAINTAINING YOUR VEHICLE Automatic Transmission – If Equipped ..342 Noise Control System Required Maintenance & Warranty ....344 Appearance Care And Protection From Corrosion .
Page 319: Engine Compartment - 6.7L Diesel
ENGINE COMPARTMENT — 6.7L DIESEL 1 — Battery 2 — Engine Oil Fill 3 — Engine Oil Dipstick 4 — Automatic Transmission Dipstick 5 — Brake Fluid Reservoir 6 — Clutch Master Cylinder (Manual Transmission Only) 7 — Battery MAINTAINING YOUR VEHICLE 317 8 —...
Page 320: Replacement Parts
318 MAINTAINING YOUR VEHICLE REPLACEMENT PARTS Use of genuine MOPAR parts for normal/scheduled maintenance and repairs is highly recommended to en- sure the designed performance. Damage or failures caused by the use of non-MOPAR parts for maintenance and repairs will not be covered by the manufacturer’s warranty.
Page 321: Maintenance Procedures
MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides those maintenance items specified in the fixed maintenance schedule, there are other components which may require servicing or replacement in the future. CAUTION! •...
Page 322 320 MAINTAINING YOUR VEHICLE parked overnight. When checking oil after operating the engine, first ensure the engine is at full operating tem- perature, then wait for 30 minutes after engine shutdown to check the oil. 1 — ADD Range 2 — Full Mark 3 —...
Page 323 Engine Oil Selection For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends engine oils that are API CJ-4 certified and meet the requirements of Chrysler Group LLC. Use MOPAR or an equivalent oil meeting Chrysler Material Standard MS-10902.
Page 324 322 MAINTAINING YOUR VEHICLE Engine Oil Viscosity (SAE Grade) Use SAE 15W-40 engine oil that meets Chrysler Materials Standard MS-10902 and the API CJ-4 engine oil category. In ambient temperatures below 0°F (-18°C), SAE 5W-40 synthetic engine oil that meets Chrysler Materials Stan- dard MS-10902 and the API CJ-4 engine oil category is required.
Page 325: Engine Air Cleaner Filter
Synthetic Engine Oils You may use synthetic engine oils provided the recom- mended oil quality requirements are met, and the recom- mended maintenance intervals for oil and filter changes are followed. Materials Added to Engine Oil The manufacturer strongly recommends against the ad- dition of any additives (other than leak detection dyes or lube odorants) to the engine oil.
Page 326 324 MAINTAINING YOUR VEHICLE The condition of the air cleaner filter is monitored by the Engine Control Module. The “SERVICE AIR FILTER” message will display in the Electronic Vehicle Informa- tion Center (EVIC) when service is required. Refer to “Electronic Vehicle Information Center” in this manual. Do not remove the top of the air filter housing to inspect the filter element on your diesel engine under normal operating conditions.
Page 327: Draining Fuel/Water Separator Filter
exhaust aftertreatment damage. This includes the use of non-approved air filters. Use only MOPAR approved air filters or equivalent. A visual inspection of the air cleaner filter element is never recommended under normal circumstances. A badly restricted element may appear clean while a soiled element may be quite effective in filtering particles without restricting air flow.
Page 328 326 MAINTAINING YOUR VEHICLE CAUTION! If the “Water In Fuel Indicator Light” remains on, DO NOT START the engine before you drain water from the fuel filter to avoid engine damage. If the “Water In Fuel Indicator Light” comes on and a single chime is heard while you are driving, or with the ignition switch in the ON position, there may be a problem with your water separator wiring or sensor.
Page 329 MAINTAINING YOUR VEHICLE 327 NOTE: The fuel/water separator drain valve is located on the bottom of the fuel filter housing. If more than a couple ounces/milliliters of fuel have been drained, follow the directions for “Priming If The Engine Has Run Out Of Fuel.” Fuel Filter Replacement Using a fuel filter that does not meet the NOTE:...
Page 330 328 MAINTAINING YOUR VEHICLE CAUTION! (Continued) • Do not prefill the fuel filter when installing a new fuel filter. There is a possibility debris could be introduced into the fuel filter during this action. It is best to install the filter dry and allow the in-tank lift pump to prime the fuel system.
Page 331: Priming If The Engine Has Run Out Of Fuel
Priming If The Engine Has Run Out Of Fuel WARNING! Do not open the high pressure fuel system with the engine running. Engine operation causes high fuel pressure. High pressure fuel spray can cause serious injury or death. 1. Add a substantial amount of fuel to the tank, approxi- mately 5 to 10 gal (19L to 38L).
Page 332: Intervention Regeneration Strategy - Evic Message Process Flow
330 MAINTAINING YOUR VEHICLE CAUTION! Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system. NOTE: • A maximum blend of 5% biodiesel, meeting ASTM specification D-6751 may be used with your Cum- mins diesel engine.
Page 333 Refer to the following messages that may be displayed on your Electronic Vehicle Information Center (EVIC): WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system.
Page 334 332 MAINTAINING YOUR VEHICLE By simply driving your vehicle at highway speeds for as little as 45 minutes, you can remedy the condition in the particulate filter system and allow your Cummins diesel engine and exhaust after-treatment system to remove the trapped PM and restore the system to normal operating condition.
Page 335: Maintenance-Free Batteries
CAUTION! See your authorized dealer, as damage to the exhaust system could occur soon with continued operation. Maintenance-Free Batteries The top of the maintenance-free batteries are perma- nently sealed. You will never have to add water, nor is periodic maintenance required. NOTE: Replacement batteries should both be of equal capacity to prevent damage to the vehicle’s charging system.
Page 336: Cooling System
334 MAINTAINING YOUR VEHICLE Battery Blanket Usage A battery loses 60% of its cranking power as the battery temperature decreases to 0°F (-18°). For the same de- crease in temperature, the engine requires twice as much power to crank at the same RPM. The use of 120 Volt AC powered battery blankets will greatly increase starting capability at low temperatures.
Page 337 If the cap is sealing properly, the engine coolant (anti- freeze) will begin to drain from the coolant recovery bottle. DO NOT REMOVE THE COOLANT PRESSURE CAP WHEN THE COOLING SYSTEM IS HOT. Cooling System – Drain, Flush and Refill Refer to the “Maintenance Schedule”...
Page 338 336 MAINTAINING YOUR VEHICLE Adding Coolant Your vehicle has been built with an improved engine coolant (antifreeze) that allows extended maintenance intervals. This engine coolant (antifreeze) can be used up to 5 Years or 105,000 miles (168 000 km) before replace- ment.
Page 339 Cooling System Pressure Cap The cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that engine coolant (antifreeze) will return to the radiator from the coolant recovery bottle. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces.
Page 340 338 MAINTAINING YOUR VEHICLE engine cold, the level of the engine coolant (antifreeze) in the coolant recovery bottle should be between the ranges indicated on the bottle. The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for engine coolant (antifreeze) freeze point or replacing en- gine coolant (antifreeze).
Page 341: Charge Air Cooler - Inter-Cooler
• Maintain engine coolant (antifreeze) concentration at 50% HOAT engine coolant (antifreeze) (minimum) and distilled water for proper corrosion protection of your engine, which contains aluminum components. • Make sure that the radiator and coolant recovery bottle overflow hoses are not kinked or obstructed. •...
Page 342: Brake System
340 MAINTAINING YOUR VEHICLE Brake System Brake Master Cylinder – Brake Fluid Level Check The fluid level of the master cylinder should be checked when performing under the hood service, or immedi- ately if the “Brake System Warning Light” indicates system failure.
Page 343: Clutch Hydraulic System
WARNING! (Continued) • To avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point.
Page 344: Manual Transmission - If Equipped
342 MAINTAINING YOUR VEHICLE Fluid Level Check This fluid level can be checked by removing the filler plug. The fluid level should be to the bottom edge of the filler plug hole with the vehicle in a level position. Manual Transmission – If Equipped Lubricant Selection Refer to “Fluids, Lubricants, and Genuine Parts”...
Page 345 4. Place the shift lever momentarily into each gear posi- tion ending with the shift lever in PARK. Make sure the engine is running at idle speed. 5. Remove the dipstick and determine if the fluid is hot or cold. Hot fluid is approximately 160°F to 175°F (70°C to 82°C).
Page 346: Noise Control System Required Maintenance & Warranty
344 MAINTAINING YOUR VEHICLE CAUTION! Be aware that if the fluid level is below 50°F (10°C), it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce a accurate reading. 8. Check for leaks. Release the parking brake. NOTE: To prevent dirt and water from entering the transmission after checking or adding fluid, make sure that the dipstick cap is properly reseated.
Page 347 Required Maintenance For Noise Control Systems The following maintenance services must be performed every six months or 7,500 miles (12 000 km) whichever comes first, to assure proper operation of the noise control systems. In addition, inspection and service should be performed anytime a malfunction is observed or suspected.
Page 348 346 MAINTAINING YOUR VEHICLE replacement, of any device or element of design incorpo- rated into any new vehicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use, or (2) the use of the vehicle after such device or element of design has been removed or rendered inoperative by any person.
Page 349 Maintenance Log and Service Chart (Diesel Engines) Noise Systems Maintenance Chart and Service Log — Insert Month, Day, Year under column mileage closest to the mileage at which service was performed. MILES 7,500 KILOMETERS 12 000 Exhaust system-inspect Air cleaner assembly-inspect ODOMETER READING PERFORMED BY...
Page 350: Appearance Care And Protection From Corrosion
348 MAINTAINING YOUR VEHICLE Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.
Page 351 Washing • Wash your vehicle regularly. Always wash your ve- hicle in the shade using MOPAR Car Wash or equiva- lent, or a mild car wash soap and rinse the panels completely with clear water. • If insects, tar or other similar deposits have accumu- lated on your vehicle, use MOPAR Super Kleen Bug and Tar Remover or equivalent to remove.
Page 352 350 MAINTAINING YOUR VEHICLE • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating, have your vehicle repaired as soon as pos- sible. The cost of such repairs is considered the respon- sibility of the owner.
Page 353 • For tough stains, apply MOPAR equivalent, or a mild soap solution to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • For grease stains, apply MOPAR Cleaner or equivalent to a clean, damp cloth and remove stain.
Page 354 352 MAINTAINING YOUR VEHICLE Cleaning Headlights Your vehicle is equipped with plastic headlights and fog lights (if equipped) that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed.
Page 355: Fuses
If the belts need cleaning, use a mild soap solution or lukewarm water. Do not remove the belts from the car to wash them. Replace the belts if they appear frayed or worn or if the buckles do not work properly. Dry with a soft tissue.
Page 356 354 MAINTAINING YOUR VEHICLE Cav- Cartridge Mini Fuse Fuse — — 15 Amp Aisin Transmission Blue Controls (Diesel Only) 20 Amp Power Sunroof Yellow 10 Amp Vistronic Fan/Wastegate Solenoid — — 10 Amp Heated Mirrors 30 Amp Off Road Module Power Pink 5 Amp Trx-Off Rd Pkg Sen (Gas...
Page 357 Cav- Cartridge Mini Fuse Fuse 15 Amp Park Lights Right Blue — — 40 Amp ABS Pump Green 30 Amp Trailer Tow Battery Feed Pink 10 Amp Occupant Restraints Controller (ORC) 2 10 Amp Occupant Restraints/ Pass Disable Switch 2 Amp IGN Switch Feed Gray 10 Amp...
Page 358 356 MAINTAINING YOUR VEHICLE Cav- Cartridge Mini Fuse Fuse 15 Amp Power Run/Start-ABS/ Blue RWAL/Smart Bar/YAW Sensor/Universal Exhaust Gas Oxygen (Uego) Sensor Controller 10 Amp PCM (Gas)/TCM (Diesel 58RFE) 10 Amp Power Ignition Run — Adjustable Pedals LED 10 Amp Power-IGN Run —...
Page 359: Vehicle Storage
CAUTION! • When installing the Integrated Power Module cover, it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in a electrical system failure.
Page 360: Replacement Bulbs
358 MAINTAINING YOUR VEHICLE NOTE: • When reinstalling the IOD fuse push firmly until fully seated; the gauges in the instrument cluster will do a full sweep when the ignition switch is turned to the RUN position. This is a normal condition. •...
Page 361: Bulb Replacement
BULB REPLACEMENT Front Headlamp (Halogen)/Park and Turn Signal Lamps CAUTION! This is a halogen bulb. Avoid touching the glass with your fingers. Reduced bulb life will result. 1. Open the hood. 2. Remove the two bolts from the front of the headlamp housing.
Page 362 360 MAINTAINING YOUR VEHICLE 3. Remove the plug from the inner fender well. 4. Remove the nut through the access hole. 5. Pull the housing out from the fender to allow room to disconnect the electrical connectors. NOTE: For easier removal, pull the headlamp assembly straight forward, applying the greatest amount of force to the outer edge of the headlamp assembly.
Page 363 6. Unlock and pull connector straight from the base of the headlamp halogen bulb. MAINTAINING YOUR VEHICLE 361 7. Twist connector on the side marker/turn signal/park lamp bulb ⁄ turn and remove connector and bulb from housing. 8. Remove housing from vehicle with headlamp halogen bulb in housing.
Page 364: Fog Lamps
362 MAINTAINING YOUR VEHICLE 9. Twist the headlamp bulb ⁄ turn and remove the headlamp bulb from the housing. 10. Replace headlamp or side marker/turn signal/park lamp bulb. Do not touch the headlamp bulb. 11. Reverse procedure for installation of bulbs and housing.
Page 365: Cab Top Clearance Lamps - If Equipped
3. Reverse procedure for installation of bulbs and housing. MAINTAINING YOUR VEHICLE 363 Cab Top Clearance Lamps — If Equipped 1. Remove the two screws from the top of the lamp.
Page 366 364 MAINTAINING YOUR VEHICLE 2. Rotate the socket ⁄ turn and pull it from the lamp 3. Pull the bulb straight from its socket and replace. assembly.
Page 367: Fluid Capacities
FLUID CAPACITIES Fuel (Approximate) Standard Rear Tank Optional Midship Tank Engine Oil with Filter 6.7L Turbo Diesel Engine Cooling System 6.7L Turbo Diesel Engine (MOPAR Antifreeze/ Coolant 5 Year/100,000 Mile Formula) or equivalent. MAINTAINING YOUR VEHICLE 365 U.S. Metric 52 Gallons 197 Liters 22 Gallons 83 Liters...
Page 368: Fluids, Lubricants And Genuine Parts
366 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Engine Fuel Filter Fluid, Lubricant, or Genuine Part MOPAR Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. In ambient temperatures below 0°F (-18°C), 5W-40 synthetic engine oil that meets Chrysler Materials Standard MS-10902 and the API CJ-4 engine oil category is required.
Page 369 Component Crankcase Ventilation Filter Fuel Selection Fluid, Lubricant, or Genuine Part MOPAR CCV Filter or equivalent. Use good quality diesel fuel from a reputable supplier in your vehicle. Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.
Page 370: Chassis
368 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission (6-Speed AS68RC) – If Equipped Manual Transmission (G-56) – If Equipped Clutch Linkage Transfer Case Front and Rear Axle (4500/5500 Models) Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part MOPAR AS68RC Automatic Transmission Fluid or equivalent.
Page 371: Maintenance Schedules
MAINTENANCE SCHEDULES CONTENTS Maintenance Schedule ....370 Oil Change Indicator System ... . 371 Perform Service Indicator .
Page 372 370 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE CAUTION! Failure to perform the required maintenance items may result in damage to the vehicle. At Each Stop for Fuel • Check the engine oil level about 30 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accuracy of the oil level reading.
Page 373 Oil Change Indicator System Ram Truck Chassis Cab (3500, 4500, and 5500 Models) Replace the engine oil and oil filter every 7,500 miles (12 000 km) or six months, or sooner if prompted by the oil change indicator system (if equipped). Under no circumstances should oil change intervals exceed 7,500 miles (12 000 km) or six months, whichever comes first.
Page 374 372 MAINTENANCE SCHEDULES 7,500 Miles (12,000 km) or 6 Months Maintenance Service Schedule ❏ When prompted by the Engine Oil Indicator System, the engine oil and filter must be changed. If not prompted by the Engine Oil Indicator System within 7,500 miles (12 000 km) or six months since the last oil and filter change, change the engine oil and engine oil filter.
Page 375 15,000 Miles (24,000 km) or 12 Months Maintenance Service Schedule ❏ When prompted by the Engine Oil Indicator System, the engine oil and filter must be changed. If not prompted by the Engine Oil Indicator System within 7,500 miles (12 000 km) or six months since the last oil and filter change, change the engine oil and engine oil filter.
Page 376 374 MAINTENANCE SCHEDULES 22,500 Miles (36,000 km) or 18 Months Maintenance Service Schedule ❏ When prompted by the Engine Oil Indicator System, the engine oil and filter must be changed. If not prompted by the Engine Oil Indicator System within 7,500 miles (12 000 km) or six months since the last oil and filter change, change the engine oil and engine oil filter.
Page 377 30,000 Miles (48,000 km) or 24 Months Maintenance Service Schedule ❏ When prompted by the Engine Oil Indicator System, the engine oil and filter must be changed. If not prompted by the Engine Oil Indicator System within 7,500 miles (12 000 km) or six months since the last oil and filter change, change the engine oil and engine oil filter. Under no circumstances should oil change intervals exceed 7,500 miles (12 000 km) or six months, whichever comes first.
Page 378 376 MAINTENANCE SCHEDULES 37,500 Miles (60,000 km) or 30 Months Maintenance Service Schedule ❏ When prompted by the Engine Oil Indicator System, the engine oil and filter must be changed. If not prompted by the Engine Oil Indicator System within 7,500 miles (12 000 km) or six months since the last oil and filter change, change the engine oil and engine oil filter.
Page 379 45,000 Miles (72,000 km) or 36 Months Maintenance Service Schedule ❏ When prompted by the Engine Oil Indicator System, the engine oil and filter must be changed. If not prompted by the Engine Oil Indicator System within 7,500 miles (12 000 km) or six months since the last oil and filter change, change the engine oil and engine oil filter. Under no circumstances should oil change intervals exceed 7,500 miles (12 000 km) or six months, whichever comes first.
Page 380 378 MAINTENANCE SCHEDULES 52,500 Miles (84,000 km) or 42 Months Maintenance Service Schedule ❏ When prompted by the Engine Oil Indicator System, the engine oil and filter must be changed. If not prompted by the Engine Oil Indicator System within 7,500 miles (12 000 km) or six months since the last oil and filter change, change the engine oil and engine oil filter.
Page 381 60,000 Miles (96,000 km) or 48 Months Maintenance Service Schedule ❏ When prompted by the Engine Oil Indicator System, the engine oil and filter must be changed. If not prompted by the Engine Oil Indicator System within 7,500 miles (12 000 km) or six months since the last oil and filter change, change the engine oil and engine oil filter. Under no circumstances should oil change intervals exceed 7,500 miles (12 000 km) or six months, whichever comes first.
Page 382 380 MAINTENANCE SCHEDULES 67,500 Miles (108,000 km) or 54 Months Maintenance Service Schedule ❏ When prompted by the Engine Oil Indicator System, the engine oil and filter must be changed. If not prompted by the Engine Oil Indicator System within 7,500 miles (12 000 km) or six months since the last oil and filter change, change the engine oil and engine oil filter.
Page 383 75,000 Miles (120,000 km) or 60 Months Maintenance Service Schedule ❏ When prompted by the Engine Oil Indicator System, the engine oil and filter must be changed. If not prompted by the Engine Oil Indicator System within 7,500 miles (12 000 km) or six months since the last oil and filter change, change the engine oil and engine oil filter. Under no circumstances should oil change intervals exceed 7,500 miles (12 000 km) or six months, whichever comes first.
Page 384 382 MAINTENANCE SCHEDULES 82,500 Miles (132,000 km) or 66 Months Maintenance Service Schedule ❏ When prompted by the Engine Oil Indicator System, the engine oil and filter must be changed. If not prompted by the Engine Oil Indicator System within 7,500 miles (12 000 km) or six months since the last oil and filter change, change the engine oil and engine oil filter.
Page 385 90,000 Miles (144,000 km) or 72 Months Maintenance Service Schedule ❏ When prompted by the Engine Oil Indicator System, the engine oil and filter must be changed. If not prompted by the Engine Oil Indicator System within 7,500 miles (12 000 km) or six months since the last oil and filter change, change the engine oil and engine oil filter. Under no circumstances should oil change intervals exceed 7,500 miles (12 000 km) or six months, whichever comes first.
Page 386 384 MAINTENANCE SCHEDULES 97,500 Miles (156,000 km) or 78 Months Maintenance Service Schedule ❏ When prompted by the Engine Oil Indicator System, the engine oil and filter must be changed. If not prompted by the Engine Oil Indicator System within 7,500 miles (12 000 km) or six months since the last oil and filter change, change the engine oil and engine oil filter.
Page 387 105,000 Miles (168,000 km) or 84 Months Maintenance Service Schedule ❏ When prompted by the Engine Oil Indicator System, the engine oil and filter must be changed. If not prompted by the Engine Oil Indicator System within 7,500 miles (12 000 km) or six months since the last oil and filter change, change the engine oil and engine oil filter. Under no circumstances should oil change intervals exceed 7,500 miles (12 000 km) or six months, whichever comes first.
Page 388 386 MAINTENANCE SCHEDULES 112,500 Miles (180,000 km) or 90 Months Maintenance Service Schedule ❏ When prompted by the Engine Oil Indicator System, the engine oil and filter must be changed. If not prompted by the Engine Oil Indicator System within 7,500 miles (12 000 km) or six months since the last oil and filter change, change the engine oil and engine oil filter.
Page 389 120,000 Miles (192,000 km) or 96 Months Maintenance Service Schedule ❏ When prompted by the Engine Oil Indicator System, the engine oil and filter must be changed. If not prompted by the Engine Oil Indicator System within 7,500 miles (12 000 km) or six months since the last oil and filter change, change the engine oil and engine oil filter. Under no circumstances should oil change intervals exceed 7,500 miles (12 000 km) or six months, whichever comes first.
Page 390 388 MAINTENANCE SCHEDULES 127,500 Miles (204,000 km) or 102 Months Maintenance Service Schedule ❏ When prompted by the Engine Oil Indicator System, the engine oil and filter must be changed. If not prompted by the Engine Oil Indicator System within 7,500 miles (12 000 km) or six months since the last oil and filter change, change the engine oil and engine oil filter.
Page 391 135,000 Miles (216,000 km) or 108 Months Maintenance Service Schedule ❏ When prompted by the Engine Oil Indicator System, the engine oil and filter must be changed. If not prompted by the Engine Oil Indicator System within 7,500 miles (12 000 km) or six months since the last oil and filter change, change the engine oil and engine oil filter. Under no circumstances should oil change intervals exceed 7,500 miles (12 000 km) or six months, whichever comes first.
Page 392 390 MAINTENANCE SCHEDULES 142,500 Miles (228,000 km) or 114 Months Maintenance Service Schedule ❏ When prompted by the Engine Oil Indicator System, the engine oil and filter must be changed. If not prompted by the Engine Oil Indicator System within 7,500 miles (12 000 km) or six months since the last oil and filter change, change the engine oil and engine oil filter.
Page 393 150,000 Miles (240,000 km) or 120 Months Maintenance Service Schedule ❏ When prompted by the Engine Oil Indicator System, the engine oil and filter must be changed. If not prompted by the Engine Oil Indicator System within 7,500 miles (12 000 km) or six months since the last oil and filter change, change the engine oil and engine oil filter. Under no circumstances should oil change intervals exceed 7,500 miles (12 000 km) or six months, whichever comes first.
Page 394 392 MAINTENANCE SCHEDULES Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all receipts. * This maintenance is not required if belt was previously replaced. **The EGR Valve and EGR Cooler maintenance will be covered by the manufacturer only at this maintenance interval, for vehicles in California, Maine, Massachusetts, New York, Vermont, Connecticut, Oregon, Rhode Island.
Page 395: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle......395 Prepare For The Appointment .
Page 396 394 IF YOU NEED CONSUMER ASSISTANCE Publication Order Forms ....399 Department Of Transportation Uniform Tire Quality Grades ......401 Treadwear .
Page 397: Suggestions For Obtaining Service For Your Vehicle
SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty.
Page 398: Chrysler Group Llc Customer Center
396 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- ship.
Page 399: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommuni- cation Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
Page 400: Warranty Information (U.s. Vehicles Only)
398 IF YOU NEED CONSUMER ASSISTANCE We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience.
Page 401: In Canada
If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your authorized dealer, and the manufacturer.
Page 402 400 IF YOU NEED CONSUMER ASSISTANCE • Service Manuals These comprehensive Service Manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing, and repairing Chrysler Group LLC vehicles. A complete working knowledge of the vehicle, system, and/or components is written in straightforward language with illustrations, diagrams, and charts.
Page 403: Traction Grades
DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle.
Page 404 402 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.
Page 405 INDEX...
Page 406 404 INDEX Adding Fuel ......272 Air Cleaner, Engine (Engine Air Cleaner Filter) ....323,345 Air Conditioning System .
Page 407 Emergency Starting ..... 307 Saving Feature (Protection) ....127 Belts, Seat .
Page 408 406 INDEX Child Seat ......59,65 Cigar Lighter ......150 Cleaning Wheels .
Page 409 Dipsticks ......319 Power Steering ......242 Disposal .
Page 410 408 INDEX Runaway ......270 Temperature Gauge ....167 Enhanced Accident Response Feature .
Page 411 Tank Capacity ......365 Fuses ....... . 353 Gauges .
Page 412 410 INDEX Hood Release ......124 Hub Caps ......303 Idle Up Feature .
Page 413 Latches ....... . 74 Leaks, Fluid ......74 Life of Tires .
Page 414 412 INDEX Tires ....... 251 Locks ....... . . 25 Child Protection .
Page 415 Occupant Restraints ....32,48,53 Occupant Restraints (Sedan) ....48 Odometer .
Page 416 414 INDEX Seats ....... 120 Steering ......241,242 Take-Off Adapter .
Page 417 Safety Checks Inside Vehicle ....73 Safety Checks Outside Vehicle ....74 Safety Defects, Reporting .
Page 418 416 INDEX Shifting ....... 220 Manual Transmission ....227 Transfer Case .
Page 419 Tachometer ......166 Tether Anchor, Child Restraint ... . . 62,66 Tilt Steering Column .
Page 420 418 INDEX Recreational ......291 Weight ......280 Towing Assistance .
Page 421 Vehicle Storage ......357 Viscosity, Engine Oil ..... . 322 Voice Recognition System (VR) .
Page 422 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
Page 423 Chrysler Group LLC 10DD43-126-AA First Edition Printed in U.S.A.

This manual is also suitable for:

Ram truck 2010

Dodge 2010 Ram Truck Chassis Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Maintaining Your Vehicle

If You Need Consumer Assistance

Quick Links

Chapters

Related Manuals for Dodge 2010 Ram Truck Chassis

Summary of Contents for Dodge 2010 Ram Truck Chassis