Page 1: Introduction
TABLE OF CONTENTS SECTION PAGE ............3 INTRODUCTION .
Page 3: Table Of Contents
INTRODUCTION CONTENTS Introduction ......4 Van Conversions/Campers ....6 How To Use This Manual .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION When it comes to service, remember that your authorized Congratulations on selecting your new Chrysler Group dealer knows your vehicle best, has factory-trained tech- LLC vehicle. Be assured that it represents precision nicians and genuine Mopar parts, and cares about your workmanship, distinctive styling, and high quality - all satisfaction.
Page 5 INTRODUCTION 5...
Page 6: Van Conversions/Campers
6 INTRODUCTION WARNINGS AND CAUTIONS Operating instructions for the special equipment in- This Owner’s Manual contains WARNINGS against op- stalled by the conversion/camper manufacturer should erating procedures that could result in an accident or also be supplied with your vehicle. If these instructions bodily injury.
Page 7: Vehicle Identification Number
INTRODUCTION 7 VEHICLE IDENTIFICATION NUMBER NOTE: It is illegal to remove or alter the VIN. The Vehicle Identification Number (VIN) is found on the VEHICLE MODIFICATIONS/ALTERATIONS left front corner of the instrument panel, visible through the windshield. This number also appears on the Auto- WARNING! mobile Information Disclosure Label affixed to a window on your vehicle, the vehicle registration and title.
Page 9: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS ▫ General Information ....17 A Word About Your Keys ....12 ▫...
Page 10 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Remote Down Window Feature — ▫ Power Windows – If Equipped ... . 34 If Equipped ......23 ▫...
Page 11 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Driver And Right Front Passenger Engine Break-In Recommendations ..79 Supplemental Restraint System (SRS) – Safety Tips ......79 Airbag .
Page 12: A Word About Your Keys
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Wireless Ignition Node (WIN) — If Equipped The Wireless Ignition Node (WIN) operates similar to an Key Fob with Remote Keyless Entry (RKE) — If ignition switch. It has four operating positions, three with Equipped detents and one that is spring-loaded.
Page 13: Key Fob
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key Fob The Key Fob operates the ignition switch. It also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the RKE transmitter go dead.
Page 14: Removing Key Fob From Ignition
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To remove the emergency key from the Key Fob, slide the Removing Key Fob From Ignition mechanical latch at the top of the Key Fob sideways with Place the shift lever in PARK. Turn the Key Fob to the your thumb and then pull the key out with your other OFF position and then remove the Key Fob.
Page 15: Key-In-Ignition Reminder
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 Refer to “Key Off Power Delay,” under “Customer- Key-In-Ignition Reminder Programmable Features (SETUP)” in the “Electronic Opening the driver’s door when the Key Fob is in the Vehicle Information Center (EVIC),” in Section 4. ignition and the ignition switch position is OFF or ACC, sounds a signal to remind you to remove the Key Fob.
Page 16: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The system uses Key Fob with factory-mated Remote If the Vehicle Security Light turns on during normal Keyless Entry (RKE) transmitter and Wireless Ignition vehicle operation (vehicle running for longer than 10 sec- Node (WIN) to prevent unauthorized vehicle operation.
Page 17: Customer Key Programming
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 • If a programmed Key Fob is lost, see your authorized CAUTION! dealer to have all remaining Key Fobs erased from the system’s memory. This will prevent the lost Key Fobs Always remove the Sentry Keys from the vehicle from starting your vehicle.
Page 18: Vehicle Security Alarm - If Equipped
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE VEHICLE SECURITY ALARM — IF EQUIPPED To Set the Alarm The Vehicle Security Alarm monitors the vehicle doors The Vehicle Security Alarm will set when you use the and ignition for unauthorized operation. When the Ve- power door locks, or use the Remote Keyless Entry (RKE) hicle Security Alarm is activated, the system provides transmitter to lock the doors.
Page 19: Illuminated Entry System - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 The Vehicle Security Alarm will also disarm if the vehicle ILLUMINATED ENTRY SYSTEM — IF EQUIPPED is started with a programmed Sentry Key . If an unpro- The courtesy lights will turn on when you use the grammed Sentry Key is used to start a vehicle, the Remote Keyless Entry (RKE) transmitter or open the engine will run for two seconds and then the alarm will...
Page 20: Remote Keyless Entry (Rke) - If Equipped
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE KEYLESS ENTRY (RKE) — IF EQUIPPED The RKE system allows you to lock or unlock the doors and activate the Panic Alarm from distances up to approximately 66 ft (20 m) using a hand-held radio transmitter with integrated key.
Page 21 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Remote Key Unlock, Driver Door/All Doors First 3. Test the feature while outside of the vehicle by press- This feature lets you program the system to unlock either ing the LOCK/UNLOCK buttons on the RKE transmitter the driver’s door or all doors on the first press of the with the ignition switch in the OFF position and the key UNLOCK button on the RKE transmitter.
Page 22: To Lock The Doors
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Flash Lamps with Remote Key Lock 3. Test the feature while outside of the vehicle by press- This feature will cause the turn signal lights to flash when ing the LOCK/UNLOCK buttons on the RKE transmitter the doors are locked or unlocked with the RKE transmit- with the ignition switch in the OFF position and the key ter.
Page 23: Remote Down Window Feature
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 Sound Horn with Remote Key Lock 3. Test the feature while outside of the vehicle by press- This feature will cause the horn to chirp when the doors ing the LOCK button on the RKE transmitter with the are locked with the RKE transmitter.
Page 24: Using The Panic Alarm
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • You may need to be less than 35 ft (11 m) from the Using the Panic Alarm To turn the Panic Alarm feature ON or OFF, press and vehicle when using the RKE transmitter to turn off the hold the PANIC button on the RKE transmitter for at Panic Alarm due to the radio frequency noises emitted least one second and release.
Page 25: General Information
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 1. With the RKE transmitter buttons facing down, use a NOTE: Changes or modifications not expressly ap- flat blade to pry the two halves of the RKE transmitter proved by the party responsible for compliance could apart.
Page 26: How To Use Remote Start
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Use Remote Start WARNING! All of the following conditions must be met before the • Do not start or run an engine in a closed garage or engine will remote start: confined area.
Page 27 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 • Remote Start Aborted - Hood Ajar • For security, power window and power sunroof op- eration (if equipped) are disabled when the vehicle is • Remote Start Aborted - Fuel Low in the Remote Start mode.
Page 28: Door Locks
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Exit Remote Start Mode and Drive the Vehicle turn on in cold weather. In warm weather, the driver Before the end of the 15-minute cycle, press and release vented seat feature will automatically turn on when the the UNLOCK button on the RKE transmitter to unlock remote start is activated.
Page 29: Power Door Locks - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 Front doors may be opened with the inside door handle Power Door Locks — If Equipped without lifting the lock plunger. A power door LOCK switch is on each front door trim panel.
Page 30 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with the EVIC, perform the If you press the power door LOCK switch while the Key Fob is in the ignition, and any front door is open, the following procedure: power locks will not operate.
Page 31 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 • For vehicles not equipped with the EVIC, perform the 8. If a chime is not heard, program mode was canceled before the feature could be disabled. If necessary, repeat following procedure: the above procedure.
Page 32: Child Protection Door Lock
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 7. Repeat the above steps to alternate the availability of this feature. 8. If a chime is not heard, the program mode was canceled before the feature could be changed. If neces- sary, repeat the above procedure.
Page 33 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 a door is engaged, that door can only be opened by using WARNING! the outside door handle even if the inside door lock is in the unlocked position. Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged.
Page 34: Windows
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOWS The control on the left front door panel has UP-DOWN switches that give you fingertip control of all power Power Windows – If Equipped windows. There is a single opening and closing switch on the front passenger door for passenger window control and on the rear doors of Quad Cab , Mega Cab and Crew Cab models.
Page 35: Auto Down
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 To open the window part way, press to the first detent WARNING! and release it when you want the window to stop. Never leave children alone in a vehicle. Leaving Auto-Up Feature with Anti-Pinch Protection unattended children in a vehicle is dangerous for a (4-Door Models Driver’s and Front Passenger Door number of reasons.
Page 36 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE rough road conditions may trigger the auto reverse press the window LOCK button into the latched or down function unexpectedly during auto closure. If this position. To enable the window controls, press the win- happens, pull the switch lightly to the first detent and dow LOCK button again and return the switch to the hold to close the window manually.
Page 37: Wind Buffeting
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 • Supplemental Side Airbag Inflatable Curtains (SABIC) Wind Buffeting Wind buffeting can be described as the perception of — if equipped pressure on the ears or a helicopter-type sound in the • An energy-absorbing steering column and steering ears.
Page 38: Lap/Shoulder Belts
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Please pay close attention to the information in this Research has shown that seat belts save lives, and they section. It tells you how to use your restraint system can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown properly, to keep you and your passengers as safe as possible.
Page 39 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 WARNING! WARNING! (Continued) • Wearing a seat belt incorrectly is dangerous. Seat • It is extremely dangerous to ride in a cargo area, belts are designed to go around the large bones of inside or outside of a vehicle.
Page 40 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt.
Page 41 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 3. When the belt is long enough to fit, insert the latch WARNING! plate into the buckle until you hear a “click.” • A belt buckled into the wrong buckle will not protect you properly.
Page 42 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • A shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt.
Page 43 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 WARNING! WARNING! • A lap belt worn too high can increase the risk of A frayed or torn belt could rip apart in a collision and internal injury in a collision. The belt forces won’t be leave you with no protection.
Page 44 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE belt tongue is pressed into the buckle. Allow the retractor panel and insert it into the black keyed buckle until there to take up the surplus webbing, and the buckles will is an audible “click”. For proper seatbelt usage, refer hang vertically from the cab back exit bezel, thus freeing “Lap/Shoulder Belt Operating Instructions”...
Page 45 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 Inserting Latch Plate In Use Position...
Page 46: Adjustable Upper Shoulder Belt Anchorage
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE away from your neck. Press the button located on the WARNING! upper belt guide, and then move it up or down to the • If the black latch and black buckle are not prop- position that fits you best.
Page 47: Center Lap Belts
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 you will prefer a higher position. When you release the WARNING! (Continued) anchorage, try to move it up or down to make sure that • A belt that is too loose or too high will apply crash it is locked in position.
Page 48: Seat Belt Pretensioners - If Equipped
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Use The Automatic Locking Mode seat belt by assuring that the belt is tight about the occupant early in a collision. Pretensioners work for all 1. Buckle the combination lap/shoulder belt. size occupants, including those in child restraints.
Page 49: Seat Belts And Pregnant Women
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 Once the warning is triggered, the BeltAlert will con- 3. Within 60 seconds of starting the vehicle, unbuckle tinue to chime and flash the Seat Belt Reminder Light for and then re-buckle the driver’s seat belt at least three 96 seconds or until the driver’s seat belt is buckled.
Page 50: Seat Belt Extender
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Keep the belt low so that it does not come across the Driver and Right Front Passenger Supplemental abdomen. That way the strong bones of the hips will take Restraint System (SRS) – Airbag the force if there is a collision.
Page 51: Airbag System Components
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 The Advanced Front Airbags have a multistage inflator design. This allows the airbag to have different rates of inflation based on the severity and type of collision. This vehicle may also be equipped with Supplemental Side Airbag Inflatable Curtains (SABIC) to protect the driver, front, and rear passengers sitting next to a win- dow.
Page 52: Advanced Front Airbag Features
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Front Passenger Airbag The first stage inflator is triggered immediately during an impact that requires airbag deployment. The timing of • Front and Side Impact Sensors — if equipped the second stage determines whether the output force is •...
Page 53 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 WARNING! (Continued) • Do not mount any accessories to the knee bolster such as alarm lights, stereos, citizen band radios, etc. Supplemental Side Airbag Inflatable Curtain (SABIC) — If Equipped SABIC airbags offer side-impact protection to front and rear seat outboard occupants in addition to that provided by the body structure.
Page 54 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Knee Impact Bolsters WARNING! The Knee Impact Bolsters help protect the knees of the • If your vehicle is equipped with left and right Side driver and the front passenger, and position everyone for the best interaction with the Advanced Front airbag.
Page 55 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Children that are not big enough to wear the vehicle seat The driver and front passenger seats should be moved belt properly (see Section on Child Restraints) should be back as far as practical to allow the Advanced Front secured in the rear seat in child restraints or belt- Airbags room to inflate.
Page 56: Airbag Deployment Sensors And Controls
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Deployment Sensors and Controls WARNING! Occupant Restraint Controller (ORC) • Relying on the airbags alone could lead to more The ORC is part of a Federally regulated safety system severe injuries in a collision. The airbags work required for this vehicle.
Page 57 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 The Advanced Front Airbags will not deploy in all frontal The ORC monitors the readiness of the electronic parts of collisions, including some that may produce substantial the system whenever the ignition switch is in the START vehicle damage —...
Page 58 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE It also includes diagnostics that will illuminate the instru- the Advanced Front Airbags. Different airbag inflation ment cluster Airbag Warning Light if a malfunction is rates are possible, based on the collision type and sever- noted.
Page 59 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 deploy the SABIC Airbags, depending on severity and Front and Side Impact Sensors — If Equipped type of collision. In these events, the ORC will deploy the In front and side impacts, impact sensors aid the ORC in SABIC only on the impact side of the vehicle.
Page 60 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Turn on the interior lights, which remain on as long as floor. They are not caused by contact with chemicals. the battery has power or until the ignition key is They are not permanent and normally heal quickly. removed.
Page 61 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Do not drive your vehicle after the airbags have de- Maintaining Your Airbag System ployed. If you are involved in another collision, the WARNING! airbags will not be in place to protect you. •...
Page 62 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Warning Light WARNING! (Continued) You will want to have the airbags ready to • Do not attempt to modify any part of your ad- inflate for your protection in a collision. While vanced airbag system.
Page 63: Event Data Recorder (Edr)
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 located on the inside of the fuse block cover for the 2. Under certain circumstances, EDR data may not be proper airbag fuses. See your authorized dealer if the recorded (e.g., loss of battery power). fuse is good.
Page 64: Child Restraint
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE accessing the electronic data stored, unless ordered to 4. Otherwise required by law. download data by a court with legal jurisdiction (i.e., Data parameters that are recorded: pursuant to a warrant). A copy of the data will be •...
Page 65 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 small children ride in proper restraint systems. This is the Infants and Small Children law, and you can be prosecuted for ignoring it. There are different sizes and types of restraints for children from newborn size to the child almost large Children 12 years and younger should ride properly enough for an adult safety belt.
Page 66 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE infant carriers do, so they can be used rearward-facing cushion while the child’s back is against the seat back, by children who weigh more than 20 lbs (9 kg) but are they should use a belt-positioning booster seat. The less than one year old.
Page 67 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 Here are some tips for getting the most out of your child from the buckle and twist the short buckle-end belt restraint: several times to shorten it. Insert the latch plate into the buckle with the release button facing out.
Page 68 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
Page 69 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 some time. In fact, many child restraint manufacturers of reach of children. It is recommended that before will provide add-on tether strap kits for some of their installing the child restraint, buckle the seat belt so the older products.
Page 70 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing the Child Restraint System We urge you to carefully follow the directions of the manufacturer when installing your child restraint. Many, WARNING! but not all, restraint systems will be equipped with separate straps on each side, with each having a hook or Do not install child restraint systems equipped with connector, and a means for adjusting the tension in the...
Page 71 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 then allow the belt to retract into the retractor. For WARNING! additional information on ALR, refer to “Automatic Locking Mode” in this section. Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or To install a child restraint, first, pull enough of the seat child restraint.
Page 72 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraint Tether Anchor WARNING! Child restraints having tether straps and hooks for con- nection to tether anchors have been available for some An incorrectly anchored tether strap could lead to time. In fact, many child restraint manufacturers will seat failure and injury to the child.
Page 73 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Tether Anchorage Points at the Right and Center Front Seat (Regular Cab - All Seats) 1. Place the child restraint on the seat and adjust the tether strap so that it will reach over the seat back under the head restraint to the tether anchor directly behind the seat.
Page 74 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Multiple Child Restraint Installation Sequence (Quad Cab /Crew Cab/Mega Cab - Rear Seats) Quad Cab /Mega Cab 1. Obtain tether straps by raising the head restraints and reaching between the rear glass and rear seat. The tether strap may be retained with an elastic band.
Page 75 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 2. Place a child restraint on each outboard rear seat and 5. Place a child restraint on the center rear seat and adjust the tether strap so that it will reach under the head adjust the tether strap so that it will reach under the head restraint to the tether anchor directly behind the seat and restraint to the tether anchor directly behind the seat and...
Page 76 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Multiple Child Restraint Quad Cab /Mega Cab 1 — Inner Anchor Strap Ring(s) 4 — Passenger’s Side Rear Child Seat 2 — Snap Hook 5 — Rear Center Child Seat 3 — Tether Strap 6 —...
Page 77 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Crew Cab 1. The tether straps loops are located between the rear glass and the rear seat. There is a tether strap loop located behind each seating position. You can gain access to the center seating position tether strap loop by raising the head restraint and reaching between the rear glass and rear seat.
Page 78 78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Pass each tether strap hook under the head restraint over the front of the seat when their back is against the and through the loop of webbing behind the child seat. seat back should use the lap/shoulder belt in a rear seat.
Page 79: Engine Break-In Recommendations
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 ENGINE BREAK-IN RECOMMENDATIONS A new engine may consume some oil during its first few A long break-in period is not required for the engine in thousand miles (kilometers) of operation. This should be your vehicle.
Page 80: Exhaust Gas
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Do not run the engine in a closed garage or in confined WARNING! (Continued) areas any longer than needed to move your vehicle in or • Do not allow people to ride in any area of your out of the area.
Page 81: Safety Checks You Should Make Inside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 damaged, have a competent mechanic inspect the com- Airbag Warning Light plete exhaust system and adjacent body areas for broken, The light should come on and remain on for six to eight damaged, deteriorated, or mispositioned parts.
Page 82: Periodic Safety Checks You Should Make Outside The Vehicle
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Periodic Safety Checks You Should Make Outside Door Latches the Vehicle Check for positive closing, latching, and locking. Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear Check area under vehicle after overnight parking for fuel, patterns.
Page 83: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS ▫ Illuminated Vanity Mirror — If Equipped ..93 Mirrors ......89 ▫...
Page 84 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Adjustable Head Restraints ....98 ▫ Driver Easy Exit And Easy Entry Control . . . 113 ▫ Eight-Way Power Seats — If Equipped ..101 To Open And Close The Hood .
Page 85 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 ▫ Daytime Running Lights (DRL) (Canada ▫ To Set a Desired Speed ....129 Only And Fleet Vehicles) ....121 ▫...
Page 86 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Security ......150 Parkview Rear Back Up Camera — If Equipped .
Page 87 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 ▫ Center Storage Compartment — Electrical Power Outlets ....154 If Equipped ......166 Cigar Lighter And Ash Receiver —...
Page 88 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Manual Sliding Rear Window — Slide-In Campers ..... . 189 If Equipped ......172 ▫...
Page 89: Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 MIRRORS Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare Inside Day/Night Mirror from vehicles behind you. You can turn the feature on or Headlight glare can be reduced by moving the small off by pressing the power button at the base of the mirror.
Page 90: Outside Mirrors
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! To avoid damage to the mirror during cleaning, never Vehicles and other objects seen in a passenger side spray any cleaning solution directly onto the mirror. convex mirror will look smaller and farther away Apply the solution onto a clean cloth and wipe the than they really are.
Page 91: Power Mirrors - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 Power Mirrors — If Equipped The controls for the power mirrors are located on the driver’s door trim panel. Folding Mirror CAUTION! Power Mirror Controls It is recommended to fold the mirrors into the full rearward position to resist damage when entering a car wash or a narrow location.
Page 92 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The power mirror controls consist of mirror select but- To adjust a mirror, press the mirror select button for the tons and a four-way mirror control switch. mirror that you want to adjust. Using the mirror control switch, press on any of the four arrows for the direction that you want the mirror to move.
Page 93: Heated Mirrors - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster. Refer to “Rear Window Features” in this section, for further information. Driver’s Automatic Dimming Mirror —...
Page 94: Trailer Towing Mirrors - If Equipped
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To use the “Slide-On-Rod” feature, rotate the sun visor Trailer Towing Mirrors — If Equipped downward and unclip it. Pull the sun visor along the These mirrors are designed with an adjustable mirror “Slide-On-Rod”...
Page 95: Uconnect™ Phone - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 NOTE: Fold the trailer towing mirrors rearward prior to uconnect™ phone — IF EQUIPPED entering an automated car wash. Refer to “uconnect™ phone” in the uconnect™ User A small blindspot mirror is located next to main mirror Manual located on the DVD for further details.
Page 96: Manual Seat Adjuster - If Equipped
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE seat. Pull up on the handle and slide the seat forward or WARNING! backward to move the seat into the most comfortable • It is extremely dangerous to ride in a cargo area, position.
Page 97: Manual Reclining Seats - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.
Page 98: Adjustable Head Restraints
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) • You can be seriously, even fatally, injured riding in • Actuating the recliner handle will allow the seat- a seat with the seatback reclined. Do not ride with back to swing (dump) forward on manual recliner the seatback reclined so that the shoulder belt is seats.
Page 99 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 To raise the head restraint, pull upward on the head To remove the head restraint, pull upward on the head restraint. To lower the head restraint, press the large restraint to it’s highest position, push in both buttons at button, located on the base of the head restraint, and the base of each head restraint rod, and simultaneously push downward on the head restraint.
Page 100 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To install the head restraint, insert the head restraint rods Rear Head Restraints into each guide, apply pressure down on the headrest The outboard head restraints can be adjusted. To raise the until the head restraint reaches the first lock position, head restraint, pull upward on the head restraint.
Page 101: Eight-Way Power Seats - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 NOTE: The rear center head restraint (Crew Cab only) is fixed and cannot be adjusted. Eight-Way Power Seats — If Equipped The power seat controls are on the outboard side of the front seat cushions. The power seat switch can be moved forward and backward as well as up and down to control the position of the seat.
Page 102: Power Lumbar - If Equipped
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.
Page 103: Heated Seats - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 Press the switch once to select High- WARNING! level heating. Press the switch a sec- ond time to select Low-level heating. Adjusting a seat while the vehicle is moving is Press the switch a third time to shut dangerous.
Page 104: Ventilated Seats - If Equipped
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The drivers heated seat can be programmed to Ventilated Seats — If Equipped come on during a remote start. Refer to “Remote Starting Located in the seat cushion and seatback are small fans System —...
Page 105: 40-20-40 Front Bench Seat - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 NOTE: Mega Cab Rear Seat Features • The engine must be running for the ventilated seats to Reclining Rear Seats — If Equipped operate. The recliner handle is located on the outside of the seat •...
Page 106 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked.
Page 107 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 2. Fold the seatback forward. Folding Rear Seat — If Equipped Both the left and right rear seats will drop and move forward when the seatback is folded flat. WARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.
Page 108 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To fold either rear seat flat: 1. Lift the handle, located on the outboard side of either of the rear seats. Rear Passenger Fold Flat Seats 3. Lift the seatback, to return the seat to the upright position.
Page 109: Driver Memory Seat - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 WARNING! Be certain that the seatback is securely locked into position. If the seatback in not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury.
Page 110: Setting Memory Positions And Linking Rke
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Keyless Entry (RKE) transmitters can also be pro- 2. Adjust the driver’s seat, recliner, and both sideview grammed to recall the same positions when the UN- mirrors to the desired positions. LOCK button is pressed. NOTE: Not all motors may be moved at one time.
Page 111: Memory Position Recall
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 8. Turn the ignition OFF and remove the key. To recall the memory settings for driver one, press MEMORY button number 1 on the driver’s seat or the 9. Press and release the LOCK button on one of the RKE UNLOCK button on the RKE transmitter linked to transmitters.
Page 112: To Disable A Rke Transmitter Linked To Memory
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: A chime sound may be heard if setting memory vehicles equipped with the Electronic vehicle Informa- was inhibited for any reason. tion Center (EVIC), refer to “Customer-Programmable Features (SETUP)” under “Electronic Vehicle Information To Disable a RKE Transmitter Linked to Memory Center (EVIC) –...
Page 113: Driver Easy Exit And Easy Entry Control
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Driver Easy Exit and Easy Entry Control TO OPEN AND CLOSE THE HOOD This additional feature provides automatic driver’s seat To open the hood, two latches must be released. positioning which will enhance driver mobility into and 1.
Page 114: Lights
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Reach into the opening beneath the center of the hood CAUTION! and push the safety latch lever from right to left to release it, before raising the hood. To prevent possible damage, do not slam the hood to close it.
Page 115: Headlights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing. CAUTION! Do not use abrasive cleaning components, solvents, steel wool or other abrasive materials to clean the lenses.
Page 116: Automatic Headlights - If Equipped
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Headlights — If Equipped 90 seconds after you turn the ignition switch to the OFF This system automatically turns the headlights on or off position. To turn the automatic headlights off, turn the according to ambient light levels.
Page 117: Headlight Delay
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 To Activate NOTE: Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause 1. To enable the Automatic High Beams, refer to headlights to remain on longer (closer to the vehicle). Customer-Programmable Features (SETUP) under Elec- Also, dirt, film and other obstructions (sticker, toll box, tronic Vehicle Information Center (EVIC) —...
Page 118: Parking Lights And Panel Lights
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Parking Lights and Panel Lights To turn on the parking lights and instrument panel lights, rotate the headlight switch clockwise to the parking light symbol. To turn off the parking lights, rotate the headlight switch back to the O (Off) position. Fog Lights —...
Page 119: Interior Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 Interior Lights to the right until you hear a click. This feature is termed Courtesy and dome lights are turned on when the front the “Parade” mode and is useful when headlights are doors are opened, when the dimmer control (rotating required during the day.
Page 120: Cargo Light
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Light Lights-on Reminder The cargo lights are turned on by pressing on the cargo If the headlights, parking lights, or cargo lights are left on button. after the ignition is turned OFF, a chime will sound when the driver’s door is opened.
Page 121: Daytime Running Lights (Drl) (Canada Only And Fleet Vehicles)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Daytime Running Lights (DRL) (Canada Only and Turn Signals Fleet Vehicles) Move the multifunction lever up or down and the arrows The headlights on your vehicle will illuminate when the on each side of the instrument cluster flash to show engine is started and the transmission is in any gear proper operation of the front and rear turn signal lights.
Page 122 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE light bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is defective. Lane Change Assist Tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off.
Page 123: Windshield Wipers And Washers
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 WINDSHIELD WIPERS AND WASHERS Intermittent Wiper System The intermittent feature of this system was designed for Windshield Wipers use when weather conditions make a single wiping cycle, The wipers and washers are operated by a switch in the with a variable pause between cycles, desirable.
Page 124: Mist Feature
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE knob is depressed while in the delay range, the wiper will WARNING! operate for several seconds after the washer knob is released. It will then resume the intermittent interval Sudden loss of visibility through the windshield previously selected.
Page 125: Heating Steering Wheel - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Pull the lever toward the steering wheel to unlock the WARNING! steering column. With one hand firmly on the steering wheel, move the steering column up or down, as desired. Tilting the steering column while the vehicle is Release the lever to lock the steering column firmly in moving is dangerous.
Page 126 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the switch to turn on the heated WARNING! steering wheel. The light on the switch • Persons who are unable to feel pain to the skin will illuminate to indicate the steering wheel heater is on.
Page 127: Driver Adjustable Pedals - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 DRIVER ADJUSTABLE PEDALS — IF EQUIPPED The power adjustable accelerator and brake pedals allow the driver to establish a comfortable position relative to the steering wheel and pedals. Adjustment 1. Position the driver’s seat so that you are at least 10 in (25.4 cm) away from the airbag, located in the center of the steering wheel.
Page 128: Electronic Speed Control - If Equipped
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become lim- ited if movement is stopped by an obstruction in the adjustable pedal’s path.
Page 129: To Activate
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 To Activate To Set a Desired Speed Push the ON/OFF button (located in the end of the lever) When the vehicle has reached the desired speed, press once and the cruise indicator light (located in the mes- the SET lever downward and then release.
Page 130: Varying The Speed Setting
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Varying The Speed Setting increments until the lever is released. Release the lever When the Electronic Speed Control is set, you can in- when the desired speed is reached, and the new set speed crease speed by pushing up and holding the RESUME will be established.
Page 131: Parksense Rear Park Assist - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 On steep hills a greater speed loss or gain may occur so limitations of this system and recommendations. it may be preferable to drive without Electronic Speed ParkSense will remember the last system state (enabled Control.
Page 132: Parksense Warning Display
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The sensors can detect obstacles from approximately 12 in (30 cm) up to 79 in (200 cm) from the rear bumper in the horizontal direction, depending on the location, type and orientation of the obstacle. ParkSense Warning Display The ParkSense Warning screen will only be displayed if Sound and Display is selected from the Customer-...
Page 133 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Rear Park Assist On Rear Park Assist Disabled...
Page 134 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense will indicate a detected obstacle by showing three solid arcs and will produce a ⁄ second tone. As the vehicle moves closer to the object the EVIC display will show fewer arcs and the sound tone will change from slow, to fast, to continuous.
Page 135 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 Continuous Tone The vehicle is close to the obstacle when the EVIC display shows one flashing arc and sounds a continuous tone.
Page 136 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING DISPLAY DISTANCES DISPLAY MESSAGE OBSTACLE DISTANCE FROM: ARC’s AUDIBLE SIG- REAR CORNERS REAR CENTER Park Assist ON None None Warning Object Detected 78.7 in (200 cm) 3 Solid Yes, 1/2 second Warning Object Detected 39.3 in (100 cm) 3 Flashing Slow Tone...
Page 137: Enable/Disable Parksense
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 Enable/Disable ParkSense ParkSense can be enabled and disabled with a switch located in the switch bank of the instrument panel or through the Customer-Programmable Features section of the EVIC. The available choices are: OFF, Sound Only, or Sound and Display.
Page 138: Service Parksense
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The switch LED will be ON when ParkSense is disabled Cleaning ParkSense or defective. The switch LED will be OFF when Park- Clean the ParkSense sensors with water, car wash soap Sense is enabled. and a soft cloth.
Page 139 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 • When you move the shift lever to the REVERSE • Clean the ParkSense sensors regularly, taking care position and ParkSense is turned off, the instrument not to scratch or damage them. The sensors must not cluster will display “PARK ASSIST DISABLED”...
Page 140 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! • The ParkSense Rear Park Assist system is only a • Drivers must be careful when backing up even parking aid and it is unable to recognize every when using the ParkSense Rear Park Assist sys- obstacle, including small obstacles.
Page 141: Understanding The Features Of Your Vehicle Parkview Rear Back Up Camera - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 PARKVIEW REAR BACK UP CAMERA — IF WARNING! (Continued) EQUIPPED • Before using the ParkSense Rear Park Assist Your vehicle may be equipped with the ParkView Rear system, it is strongly recommended that the ball Back Up Camera that allows you to see an on-screen mount and hitch ball assembly is disconnected image of the rear of your vehicle whenever the shift lever...
Page 142: Turning Parkview On Or Off - With Navigation Radio
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! (Continued) • To avoid vehicle damage, the vehicle must be Drivers must be careful when backing up even when driven slowly when using ParkView to be able to using the ParkView Rear Back Up Camera. Always stop in time when an obstacle is seen.
Page 143: Turning Parkview On Or Off - Without Navigation Radio
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 4. Enable or disable the rear camera feature by selecting 4. When the vehicle is shifted into REVERSE, an image of enable rear camera in reverse soft key. the rear of the vehicle will appear with a caution note to check entire surroundings displayed across the top of 5.
Page 144: Courtesy/Reading Lights
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Universal Garage Door Opener — If Equipped UNLOCK button is pressed on the Remote Keyless Entry (RKE) transmitter, if equipped. These lights are also operated individually as reading lights by pressing on the corresponding lens.
Page 145: Garage Door Opener - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 NOTE: The courtesy/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. If the interior lights are left on after the ignition is turned OFF, they will extinguish after 15 minutes.
Page 146 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The HomeLink buttons are located in the overhead WARNING! console, and contain one, two or three dots/lines desig- • Your motorized door or gate will open and close nating the different HomeLink channels. while you are training the Universal Transceiver.
Page 147: Programming Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 Programming HomeLink 2. Place the handheld transmitter 1 to 3 in (3 to 8 cm) from the HomeLink buttons while keeping the EVIC Before You Begin display in view. If you have not trained any of the HomeLink buttons, erase all channels before you begin training.
Page 148 148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Some gate operators and garage door openers This can usually be found where the hanging antenna may require you to replace Step 3 with procedures noted wire is attached to the garage door opener motor (it is in the “Gate Operator/Canadian Programming”...
Page 149: Gate Operator/Canadian Programming
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 6. Firmly press and release the LEARN or TRAINING Gate Operator/Canadian Programming button. The name and color of the button may vary by Canadian radio-frequency laws require transmitter sig- manufacturer. nals to “time-out” (or quit) after several seconds of transmission –...
Page 150: Using Homelink
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE successfully accepted the frequency signal. The EVIC 2. Press and hold the desired HomeLink button for display will change from “CHANNEL # TRAINING” to 20 seconds until the EVIC display states “CHANNEL # “CHANNEL # TRAINED.”...
Page 151: Troubleshooting Tips
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Troubleshooting Tips 2. This device must accept any interference that may be If you are having trouble programming HomeLink , here received including interference that may cause undesired are some of the most common solutions: operation.
Page 152: Power Sunroof - If Equipped
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED WARNING! The power sunroof switch is located on the overhead • Never leave children alone in a vehicle. Leaving console between the courtesy/reading lights. unattended children in a vehicle is dangerous for a number of reasons.
Page 153: Open Sunroof - Express Mode
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Open Sunroof — Express Mode sunroof will automatically retract. Remove the obstruc- Momentarily pressing the switch rearward will activate tion if this occurs. Next, press the switch forward and the Express Open Feature, causing the sunroof to open release to Express Close.
Page 154: Sunshade Operation
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunshade Operation Sunroof Maintenance The sunshade can be opened manually. However, the Use only a non-abrasive cleaner and a soft cloth to clean sunshade will open automatically as the sunroof opens. the glass panel. NOTE: The sunshade cannot be closed if the sunroof is Sunroof Fully Closed open.
Page 155 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 NOTE: • To ensure proper operation a MOPAR knob and element must be used. • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. The auxiliary power outlets can be found in the following locations: •...
Page 156 156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Inside the upper lid of the center storage compartment — if equipped. Power Outlet — Rear Center Console The key symbol indicates that this outlet can supply power when the key is in the ON/RUN or ACC posi- Power Outlet —...
Page 157 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 WARNING! CAUTION! • Many accessories that can be plugged in draw To avoid serious injury or death: • Only devices designed for use in this type of power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
Page 158: Cigar Lighter And Ash Receiver - If Equipped
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CIGAR LIGHTER AND ASH RECEIVER — IF EQUIPPED A removable ash receiver and cigar lighter are available. For vehicles with a bench seat the cupholder tray can be used to hold the ash receiver. Ash Receiver and Cigar Lighter (Bench Seat) 1 —...
Page 159: Power Inverter - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 For vehicles equipped with an optional floor shifter. POWER INVERTER — IF EQUIPPED A 115 Volt (150 Watts Maximum) outlet is located on the center stack of the instrument panel, to the right of the radio.
Page 160 160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The power inverter is designed with built-in overload protection. If the power rating of 150 Watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet the inverter should automatically reset.
Page 161: Cupholders
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 NOTE: CUPHOLDERS • When the power inverter switch is pressed, there will Front Instrument Panel Cupholders — (40–20–40 be a delay of approximately one second before the Seats) power inverter status indicator turns on. The status The cupholders are located in the pull-out tray at the indicator of the AC power inverter indicates whether bottom of the center stack.
Page 162: Front Instrument Panel Cupholders - Floor Mounted Shifter
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Instrument Panel Cupholders — Floor Rear Cupholder — Quad Cab Mounted Shifter Quad Cab vehicles may be equipped with a rear cup- For vehicles equipped with bucket seats and a floor holder that consists of two cup wells for rear passenger mounted shifter there are two cupholders located in the convenience.
Page 163: Rear Cupholder - Crew Cab
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 Rear Cupholder — Crew Cab STORAGE Crew Cab vehicles are equipped with rear cupholders Glove Box Storage located in the center armrest. The glove box is located on the passenger side of the instrument panel and features both an upper and lower storage area.
Page 164 164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To open the upper glove box push upward on the handle To open the lower glove box, pull on the handle to release release. The glove box door will automatically open. the latch and lower the door. Upper Glove Box Lower Glove Box...
Page 165: Door Storage
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 Door Storage Rear Door Storage — Crew Cab Storage compartments are located in both the driver and Front Door Storage — If Equipped passenger door trim panels. Storage areas and bottle holders (drivers side only) are located in the door trim panels.
Page 166: Center Storage Compartment - If Equipped
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Center Storage Compartment — If Equipped WARNING! The center storage compartment is located between the • This armrest is not a seat. Anyone seated on the driver and passenger seats. The storage compartment provides an armrest and contains both and upper and armrest could be seriously injured during vehicle lower storage area.
Page 167 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 Upper Storage Compartment Lower Storage Bin With the upper lid closed, pull on the lower handle to open the lower storage bin.
Page 168: Second Row In-Floor Storage Bin - If Equipped
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Second Row In-Floor Storage Bin — If Equipped To open in-floor storage bin, lift upward on the handle of In-floor storage bins are located in front of the second the latch and open the lid. row seats and can be used for extra storage.
Page 169: Seatback Storage
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 Seatback Storage Storage (Regular Cab) Located in the back of both the driver and passenger The storage bin is located behind the front seats and runs front seats are pockets that can be used for storage. the length of the cab.
Page 170: Storage And Seats (Crew Cab)
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage and Seats (Crew Cab) CAUTION! The Crew Cab models provide additional storage under the rear seats. Lift the seats to access the storage com- Always lift the storage compartment lids by using partment.
Page 171: Rear Window Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 when the rear window defroster is on. The rear window defroster automatically turns off after approximately 10 minutes. For an additional five minutes of operation, press the button a second time. NOTE: To prevent excessive battery drain, use the rear window defroster only when the engine is operating.
Page 172: Power Sliding Rear Window - If Equipped
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) • Do not use scrapers, sharp instruments, or abra- sive window cleaners on the interior surface of the window. • Keep all objects a safe distance from the window. Power Sliding Rear Window — If Equipped The switch for the power sliding rear window is located on the overhead console.
Page 173: Fold Flat Load Floor - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 FOLD FLAT LOAD FLOOR — IF EQUIPPED Unfolding the Load Floor Quad Cab models with a 60/40 rear seat may be 1. Lift the 60/40 seat cushion(s) to the upward position. equipped with a folding load floor. WARNING! Do not operate the vehicle with loose items stored on the load floor.
Page 174 174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Grasp the knob on the load floor and lift the knob until Positioning the Load Floor for Storage Access Under the load floor unfolds into position. the Seat 1. Lift the 60/40 seat cushion(s) to the upward position. 2.
Page 175: Pickup Box
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 PICKUP BOX RamBox™ — If Equipped The RamBox™ system is an integrated pickup box stor- age and cargo management system consisting of three features: • Integrated box side storage bins • Cargo extender/divider •...
Page 176 176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE RamBox™ Integrated Box Side Storage Bins CAUTION! Cargo storage bins are located on both sides of the pickup box. The cargo storage bins provide watertight, lockable, Failure to follow the following items could cause illuminated storage for up to 150 lbs (68 kg) of evenly damage to the vehicle: distributed cargo.
Page 177 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 To open a storage bin, press and release the pushbutton The interior of the RamBox™ will automatically illumi- located on the lid. The RamBox™ lid will open upward to nate when the lid is opened. In addition to the automatic allow hand access.
Page 178 178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! CAUTION! (Continued) • Loads applied to the top of the bin lid should be Leaving the lid open for extended periods of time minimized to prevent damage to the lid and could cause the vehicle battery to discharge. If the lid latching/hinging mechanisms.
Page 179: Rambox™ Safety Warning
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 RamBox™ Safety Warning RamBox™ Storage Bin Cover Emergency Release Carefully follow these warnings to help prevent personal Lever — If Equipped injury or damage to your vehicle: As a security measure, a Storage Bin Cover Emergency Release is built into the storage bin cover latching mecha- WARNING! nism.
Page 180: Bed Extender - If Equipped
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In the event of an individual being locked inside 1. Make sure the center handle is unlocked using the the storage bin, the storage bin cover can be opened from vehicle key and rotate the center handle vertically to inside of the bin by pulling on the glow-in-the-dark lever release the extender side gates.
Page 181 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 2. With the side gates open, position the extender fully 3. Rotate the side gates closed allowing the outboard forward in the bed against the front panel. ends to be positioned in front of the cargo tie down loops. Storage Position Cargo Tie Down Loop...
Page 182 182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Rotate the center handle horizontally to secure the side Divider Position gates in the closed position. The divider position is intended for managing your cargo and assisting in keeping cargo from moving around the bed.
Page 183 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 Center Handle and Lock Aligning Gate To Slots 3. Rotate the side gates closed so that the outboard ends 1 — Center Handle Lock 2 — Handle are secured into the intended slots of the bed. 2.
Page 184 184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Rotate the center handle horizontally to secure the side Extender Position gates in the closed position. The extender position allows you to load the bed of the truck beyond the tail gate. The bed extender will add an additional 15 in (38 cm) in the back of the truck when additional cargo room is needed.
Page 185 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 To install the bed extender into the extender position perform the following: 1. Lower the tailgate. 2. Make sure the center handle is unlocked and rotate the center handle vertically in order to release the extender side gates.
Page 186 186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Rotate the handles to the horizontal position to secure WARNING! into place. To reduce the risk of potential injury or property damage: • Cargo must be secured. • Do not exceed cargo load rating of your vehicle. •...
Page 187: Bed Rail Tie-Down System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 Bed Rail Tie-Down System CAUTION! The maximum load per cleat should not exceed 250 lbs (113 kg) and the angle of the load on each cleat should not exceed 60 degrees above horizontal, or damage to the cleat or cleat rail may occur.
Page 188 188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE out on the cleat and slide it to the detent nearest the To remove the cleats from the utility rail, remove the end desired location. Make sure the cleat is seated in the cap by pushing up on the locking tab, located on the detent and tighten the nut.
Page 189: Slide-In Campers
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 SLIDE-IN CAMPERS Disconnecting the Rear Camera — If Equipped Camper Applications 1. Open the tailgate to access the rear camera connector Certain truck models are not recommended for slide-in bracket located on the rear sill. campers.
Page 190: Removing The Tailgate
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Remove the connector bracket from the sill by press- 4. Connect the chassis plug and bracket (provided in the ing inward in the locking tab. glove box) to the chassis wiring harness and insert the bracket back into the sill.
Page 191: Locking Tailgate - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 2. Unlatch the tailgate and remove the support cables by 5. Remove the tailgate from the vehicle. releasing the lock tang from the pivot. NOTE: Do not carry the tailgate loose in the truck pickup box.
Page 193: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS ▫ EVIC Displays ..... . 222 Instrument Panel Features ....197 ▫...
Page 194 194 UNDERSTANDING YOUR INSTRUMENT PANEL Sales Code (RER/REN) — AM/FM/CD/DVD Sales Code RES/RSC — AM/FM Stereo Radio Radio – If Equipped ....238 With CD Player (MP3 AUX Jack) And Sirius Radio.
Page 195 UNDERSTANDING YOUR INSTRUMENT PANEL 195 ▫ Play Mode ......263 ▫ Operating Instructions - uconnect™ phone (If Equipped) .
Page 196 196 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Automatic Temperature Control (ATC) — ▫ Window Fogging And Frosting ..285 If Equipped ......279 ▫...
Page 197: Instrument Panel Features
UNDERSTANDING YOUR INSTRUMENT PANEL 197 INSTRUMENT PANEL FEATURES 1 — Headlight Switch 7 — 115v Power Inverter Outlet 13 — Transfer Case Position Switch 2 — Instrument Cluster 8 — Power Outlet 14 — Ignition Switch 3 — Radio 9 — Lower Switch Bank 15 —...
Page 198: Switch Bank Button Description
198 UNDERSTANDING YOUR INSTRUMENT PANEL SWITCH BANK BUTTON DESCRIPTION 1. TOW/HAUL Refer to Section 5 for more information. Upper Switch Bank 2. ESP OFF The upper switch bank is located on the center of the Refer to Section 5 for more information. instrument panel.
Page 199: Lower Switch Bank
UNDERSTANDING YOUR INSTRUMENT PANEL 199 Lower Switch Bank 1. HEATED SEATS Refer to Section 3 for more information. The lower switch bank is located on the center of the instrument panel. 2. VENTILATED SEATS Refer to Section 3 for more information. 3.
Page 200: Instrument Cluster - Base
200 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — BASE...
Page 201: Instrument Cluster - Premium
UNDERSTANDING YOUR INSTRUMENT PANEL 201 INSTRUMENT CLUSTER — PREMIUM...
Page 202: Instrument Cluster Description
202 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION NOTE: • A continuous chime will sound if the vehicle is driven 1. Tachometer more than 1 mile (1.6 km) with either turn signal on. The Tachometer indicates engine speed in revolutions per •...
Page 203 UNDERSTANDING YOUR INSTRUMENT PANEL 203 The gauge pointer will likely indicate a higher tempera- WARNING! ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to A hot engine cooling system is dangerous. You or exceed the upper limits of the normal operating range.
Page 204 204 UNDERSTANDING YOUR INSTRUMENT PANEL 6. 4 LOW If a problem is detected, the light will come on while the This light alerts the driver that the vehicle is in engine is running. Cycle the ignition key when the the four-wheel drive LOW mode. The front and vehicle has completely stopped and the shift lever is rear driveshafts are mechanically locked to- placed in the PARK position, the light should turn off.
Page 205 UNDERSTANDING YOUR INSTRUMENT PANEL 205 8. 4WD Indicator Center (EVIC). Refer to ”Electronic Vehicle Information This light indicates the vehicle is in four-wheel Center (EVIC) — If Equipped” in this section for more drive and 4LOCK. 4WD allows all four wheels information.
Page 206 206 UNDERSTANDING YOUR INSTRUMENT PANEL 13. Vehicle Security Light — If Equipped 16. Odometer / Electronic Vehicle Information Center This light will flash at a fast rate for approxi- (EVIC) Display Area — If Equipped mately 15 seconds, when the vehicle security Odometer alarm is arming, and then will flash slowly The odometer shows the total distance the vehicle has...
Page 207 UNDERSTANDING YOUR INSTRUMENT PANEL 207 The two trip odometers show individual trip mileage. To NOTE: There is also an engine hour function. This switch from odometer to trip odometers, press and indicates the total number of hours the engine has been release the TRIP ODOMETER button.
Page 208 208 UNDERSTANDING YOUR INSTRUMENT PANEL driving habits in order to increase fuel economy. The noFUSE ECO display will toggle on and off depending on driving If the vehicle diagnostic system determines that the habits and vehicle usage. Ignition Off Draw (IOD) fuse is improperly installed, or damaged, a “noFUSE”...
Page 209 UNDERSTANDING YOUR INSTRUMENT PANEL 209 Unless reset, this message will continue to display each 17. Engine Temperature Warning Light time you turn the ignition switch to the ON position. To This light warns of an overheated engine condi- turn off the message temporarily, press and release the tion.
Page 210 210 UNDERSTANDING YOUR INSTRUMENT PANEL For vehicles equipped with a premium cluster this indi- 19. Low Fuel Light cator will display in the Electronic Vehicle Information When the fuel level reaches approximately 3.0 gal Center (EVIC). Refer to ”Electronic Vehicle Information (11.0 L) this light will turn on, and remain on until Center (EVIC) —...
Page 211 UNDERSTANDING YOUR INSTRUMENT PANEL 211 moves to either extreme left or right and remains there 23. Brake Warning Light during normal driving, the electrical system should be This light monitors various brake functions, serviced. including brake fluid level and parking brake application.
Page 212 212 UNDERSTANDING YOUR INSTRUMENT PANEL The dual brake system provides a reserve braking capac- WARNING! ity in the event of a failure to a portion of the hydraulic system. A leak in either half of the dual brake system is Driving a vehicle with the red brake light on is indicated by the Brake Warning Light, which will turn on dangerous.
Page 213 UNDERSTANDING YOUR INSTRUMENT PANEL 213 The light also will turn on when the parking brake is Center (EVIC). Refer to ”Electronic Vehicle Information applied with the ignition switch in the ON position. Center (EVIC) — If Equipped” in this section for more information.
Page 214 214 UNDERSTANDING YOUR INSTRUMENT PANEL Accordingly, when the low tire pressure telltale illumi- illuminated. This sequence will continue upon subse- nates, you should stop and check your tires as soon as quent vehicle start-ups as long as the malfunction exists. possible, and inflate them to the proper pressure.
Page 215 UNDERSTANDING YOUR INSTRUMENT PANEL 215 26. Malfunction Indicator Light (MIL) CAUTION! The Malfunction Indicator Light (MIL) is part of an onboard diagnostic (OBDII) system which The TPMS has been optimized for the original monitors the emissions and engine control sys- equipment tires and wheels.
Page 216 216 UNDERSTANDING YOUR INSTRUMENT PANEL Although your vehicle will usually be drivable and not WARNING! need towing, see your authorized dealer for service as soon as possible. A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal CAUTION! operating conditions.
Page 217 UNDERSTANDING YOUR INSTRUMENT PANEL 217 28. Front Fog Light Indicator — If Equipped 30. Transmission Temperature Light This indicator will illuminate when the front fog This light indicates that there is excessive trans- lights are on. mission fluid temperature that might occur with severe usage such as trailer towing.
Page 218 218 UNDERSTANDING YOUR INSTRUMENT PANEL remain on continuously. Refer to Enhanced Seat Belt Use WARNING! Reminder System (BeltAlert ) in the Occupant Re- straints section for more information. In some circumstances a Transmission Temperature Indicator, under continued operation, could cause the 32.
Page 219 UNDERSTANDING YOUR INSTRUMENT PANEL 219 For vehicles equipped with a premium cluster this indi- For vehicles equipped with a premium cluster this indi- cator will display in the Electronic Vehicle Information cator will display in the Electronic Vehicle Information Center (EVIC). Refer to ”Electronic Vehicle Information Center (EVIC).
Page 220: Electronic Vehicle Information Center (Evic) - If Equipped
220 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC VEHICLE INFORMATION CENTER NOTE: The compass on your vehicle is self-calibrating, (EVIC) — IF EQUIPPED eliminating the need to manually calibrate the compass. The Electronic Vehicle Information Center (EVIC) fea- This system conveniently allows the driver to select a tures a driver-interactive display that is located in the variety of useful information by pressing the switches instrument cluster.
Page 221 UNDERSTANDING YOUR INSTRUMENT PANEL 221 • Audio Modes display Steering wheel EVIC control button as it appears on the right side of the Steering wheel EVIC control button, as steering wheel. it appears on the left side of the steer- ing wheel.
Page 222: Evic Displays
222 UNDERSTANDING YOUR INSTRUMENT PANEL • Right Front Turn Signal Light Out EVIC Displays When the appropriate conditions exist, the EVIC displays • Right Rear Turn Signal Light Out the following messages: • Park Assist Disabled • ECO (Fuel Saver Indicator) — If Equipped •...
Page 223 UNDERSTANDING YOUR INSTRUMENT PANEL 223 vehicle and shut off the engine as soon as possible. A If jump starting is required, refer to “Jump Starting chime will sound for four minutes when this light turns Procedures” in section 6 of this manual. •...
Page 224 224 UNDERSTANDING YOUR INSTRUMENT PANEL If the light remains lit with the engine running your shift the transmission into NEUTRAL and idle the ve- vehicle, will usually be drivable, however, see an autho- hicle. If the temperature reading does not return to rized dealer for service as soon as possible.
Page 225 UNDERSTANDING YOUR INSTRUMENT PANEL 225 with the engine running. If the ESP/BAS Warning Light CAUTION! comes on continuously with the engine running, a mal- function has been detected in either the ESP or the BAS Continuous driving with the Transmission Tempera- system.
Page 226 226 UNDERSTANDING YOUR INSTRUMENT PANEL • Loose Gascap Message indicator system is duty-cycle based, which means the If the vehicle diagnostic system determines engine oil change interval may fluctuate dependent upon that the fuel filler cap is loose, improperly your personal driving style. installed, or damaged, a loose gascap icon will Unless reset, this message will continue to display each display in the telltale display area.
Page 227: Distance To Empty (Dte)
UNDERSTANDING YOUR INSTRUMENT PANEL 227 Distance To Empty (DTE) to a text display of LOW FUEL. This display will continue until the vehicle runs out of fuel. Adding a Shows the estimated distance that can be traveled with significant amount of fuel to the vehicle will turn off the the fuel remaining in the tank.
Page 228: Trip Functions
228 UNDERSTANDING YOUR INSTRUMENT PANEL The FUEL SAVER MODE message will display above the This feature allows you to monitor when you are driving average fuel economy in the EVIC display. This message in a fuel efficient manner, and it can be used to modify will appear whenever MDS (if equipped) allows the driving habits in order to increase fuel economy.
Page 229: System (Customer Information Features)
UNDERSTANDING YOUR INSTRUMENT PANEL 229 The Trip Functions mode displays the following informa- being displayed. To reset all resettable functions, press tion. and release the ODOMETER/TRIP ODOMETER button a second time within three seconds of resetting the • Trip A currently-displayed function.
Page 230: Compass Display
230 UNDERSTANDING YOUR INSTRUMENT PANEL • Trans Temperature NOTE: A good calibration requires a level surface and Displays the actual transmission temperature. an environment free from large metallic objects such as buildings, bridges, underground cables, railroad tracks, • Engine Hours etc.
Page 231 UNDERSTANDING YOUR INSTRUMENT PANEL 231 5. Complete one or more 360–degree turns (in an area free from large metal or metallic objects) until the “CAL” indicator turns off. The compass will now function normally. Compass Variance Compass Variance is the difference between Magnetic North and Geographic North.
Page 232: Customer-Programmable Features (Setup)
232 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Press the DOWN button until the “Compass Variance” Select Language message is displayed in the EVIC, then press the SELECT When in this display you may select one of five lan- button. The last variance zone number displays in the guages for all display nomenclature, including the trip EVIC.
Page 233 UNDERSTANDING YOUR INSTRUMENT PANEL 233 Enable/Disable the Rear Park Assist System feature showing the system has been activated, or the The Rear Park Assist system will scan for objects behind check-mark is removed showing the system has been the vehicle when the transmission is in the REVERSE and deactivated.
Page 234 234 UNDERSTANDING YOUR INSTRUMENT PANEL 1st Press is selected, all of the doors will unlock on the Remote Start Comfort Sys. first press of the RKE transmitter UNLOCK button. To When this feature is selected and the remote start is make your selection, press and release the SELECT activated, the heated steering wheel and driver heated button until “Driver Door 1st Press”...
Page 235 UNDERSTANDING YOUR INSTRUMENT PANEL 235 feature showing the system has been activated or the button until a check-mark appears next to the feature check-mark is removed, showing the system has been showing the system has been activated or the check-mark deactivated.
Page 236 236 UNDERSTANDING YOUR INSTRUMENT PANEL system has been activated or the check-mark is removed, Easy Exit Seat — If Equipped showing the system has been deactivated. When this feature is selected it provides automatic driver seat positioning to enhance driver mobility when enter- Automatic High Beams —...
Page 237 UNDERSTANDING YOUR INSTRUMENT PANEL 237 objects in close proximity to the rear of the vehicle. To unlocked with the RKE transmitter. To make your selec- make your selection, press and release the SELECT tion, press and release the SELECT button until “OFF,” button until a check-mark appears next to the feature “30 sec.,”...
Page 238: Sales Code (Rer/Ren) - Am/Fm/Cd/Dvd Radio - If Equipped
238 UNDERSTANDING YOUR INSTRUMENT PANEL Display Units of Measure In The REN and RER radios contain a CD/DVD player, USB The EVIC, odometer, and navigation system (if port, and a 30-gigabyte hard drive (HDD). Sirius Satellite equipped) can be changed between English and Metric Radio is optional.
Page 239: Clock Setting Procedure
UNDERSTANDING YOUR INSTRUMENT PANEL 239 Clock Setting Procedure 4. To move the hour forward, touch the screen where the word “Hour” with the arrow pointing upward is dis- uconnect™ gps — RER only played. To move the hour backward, touch the screen The GPS receiver used in this system is synchronized to where the word “Hour”...
Page 240 240 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Touch the screen where the time is displayed. The Changing the Time Zone clock setting menu will appear on the screen. 1. Turn on the radio. 3. When this feature is on, a check mark will appear in 2.
Page 241: Sales Code Res - Am/Fm Stereo Radio With Cd Player (Mp3 Aux Jack)
UNDERSTANDING YOUR INSTRUMENT PANEL 241 SALES CODE RES — AM/FM STEREO RADIO Operating Instructions — Radio Mode WITH CD PLAYER (MP3 AUX JACK) NOTE: The ignition switch must be in the ON or ACC NOTE: The radio sales code is located on the lower right position to operate the radio.
Page 242 242 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons 4. Adjust the minutes using the right side TUNE/ Press and release the SEEK buttons to search for the next SCROLL control knob. Press the TUNE/SCROLL control listenable station in AM/FM mode. Press the right switch knob to save time change.
Page 243 UNDERSTANDING YOUR INSTRUMENT PANEL 243 Push the rotary TUNE/SCROLL control knob a second Push the rotary TUNE/SCROLL control knob again to time and MID will display. Turn the TUNE/SCROLL exit setting tone, balance, and fade. control knob to the right or left to increase or decrease the AM/FM Button mid-range tones.
Page 244: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
244 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each pushbutton by Operation Instructions — CD MODE For CD And repeating the above procedure with this exception: Press MP3 Audio Play the SET/RND button twice and SET 2 will show in the NOTE: display window.
Page 245 UNDERSTANDING YOUR INSTRUMENT PANEL 245 If you insert a disc with the ignition ON and the radio EJECT Button - Ejecting a CD ON, the unit will switch from radio to CD mode and Press the EJECT button to eject the CD. begin to play when you insert the disc.
Page 246: Notes On Playing Mp3 Files
246 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button Press the RND button a second time to stop Random Press this button to change the display from a large CD Play. playing time display to a small CD playing time display. Notes on Playing MP3 Files RW/FF The radio can play MP3 files;...
Page 247 UNDERSTANDING YOUR INSTRUMENT PANEL 247 The radio uses the following limits for file systems: Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal • Maximum number of folder levels: 8 CD audio tracks and computer files (including MP3 files). •...
Page 248 248 UNDERSTANDING YOUR INSTRUMENT PANEL rates (VBR) are also supported. The majority of MP3 files Playback of MP3 Files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or When a medium containing MP3 data is loaded, the VBR bit rate.
Page 249: Operation Instructions - Auxiliary Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 249 Operation Instructions - Auxiliary Mode SALES CODE RES/RSC — AM/FM STEREO The auxiliary (AUX) jack is an audio input jack, which RADIO WITH CD PLAYER (MP3 AUX JACK) AND allows the user to plug in a portable device, such as an SIRIUS RADIO MP3 player, or cassette player, and utilize the vehicle’s NOTE: The radio sales code is located on the lower right...
Page 250: Operating Instructions - Radio Mode
250 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Radio Mode to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make NOTE: The ignition switch must be in the ON or ACC another selection.
Page 251 UNDERSTANDING YOUR INSTRUMENT PANEL 251 Phone Button uconnect™ phone — If Equipped 3. After adjusting the hours, press the right side TUNE/ Press this button to operate the uconnect™ phone feature SCROLL control knob to set the minutes. The minutes (if equipped).
Page 252 252 UNDERSTANDING YOUR INSTRUMENT PANEL INFO Button Push the rotary TUNE/SCROLL control knob a second Press the INFO button for an RDS station (one with call time and MID will display. Turn the TUNE/SCROLL letters displayed). The radio will return a Radio Text control knob to the right or left to increase or decrease the message broadcast from an FM station (FM mode only).
Page 253 UNDERSTANDING YOUR INSTRUMENT PANEL 253 Push the rotary TUNE/SCROLL control knob again to 16-Digit Character Program Type exit setting tone, balance, and fade. Display Classic Rock Cls Rock MUSIC TYPE Button College College Pressing this button once will turn on the Music Type mode for five seconds.
Page 254 254 UNDERSTANDING YOUR INSTRUMENT PANEL SETUP Button 16-Digit Character Program Type Pressing the SETUP button allows you to select between Display the following items: Soft Soft • Set Clock — Pressing the SELECT button will allow Soft Rock Soft Rck you to set the clock.
Page 255: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
UNDERSTANDING YOUR INSTRUMENT PANEL 255 window. Select the button (1–6) you wish to lock onto this Buttons 1 - 6 station and press and release that button. If a button is These buttons tune the radio to the stations that you not selected within five seconds after pressing the SET/ commit to pushbutton memory (12 AM and 12 FM RND button, the station will continue to play but will not...
Page 256 256 UNDERSTANDING YOUR INSTRUMENT PANEL Inserting Compact Disc(s) CAUTION! (Continued) Gently insert one CD into the CD player with the CD • Do not use adhesive labels. These labels can peel label facing up. The CD will automatically be pulled into away and jam the player mechanism.
Page 257: Notes On Playing Mp3 Files
UNDERSTANDING YOUR INSTRUMENT PANEL 257 NOTE: Ejecting with the ignition OFF is not allowed on AM/FM Button convertible or soft-top models (if equipped). Press the button to select either AM or FM mode. SEEK Button SET/RND Button (Random Play Button) Press the right SEEK button for the next selection on the Press this button while the CD is playing to activate CD.
Page 258 258 UNDERSTANDING YOUR INSTRUMENT PANEL Supported Media (Disc Types) a number instead. With a maximum number of files, The MP3 file recording media supported by the radio are exceeding 20 folders will result in this display. With CDDA, CD-R, CD-RW, MP3, and CDDA+MP3. 200 files, exceeding 50 folders will result in this display.) Supported Medium Formats (File Systems)
Page 259 UNDERSTANDING YOUR INSTRUMENT PANEL 259 Supported MP3 File Formats MPEG Sampling Bit Rate (kbps) The radio will recognize only files with the *.MP3 exten- Specification Frequency (kHz) sion as MP3 files. Non-MP3 files named with the *.MP3 160, 128, 144, extension may cause playback problems.
Page 260: List Button (Cd Mode For Mp3 Play)
260 UNDERSTANDING YOUR INSTRUMENT PANEL Loading times for playback of MP3 files may be affected begin playing the files contained in that folder (or the by the following: next folder in sequence if the selection does not contain playable files). •...
Page 261: Universal Consumer Interface (Uci) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 261 Operation Instructions - Auxiliary Mode Operating Instructions - uconnect™ phone (If The auxiliary (AUX) jack is an audio input jack which Equipped) allows the user to plug in a portable device such as an Refer to “uconnect™ phone” in the uconnect™ User MP3 player or cassette player and utilize the vehicle’s Manual located on the DVD for further details.
Page 262: Connecting The Ipod
262 UNDERSTANDING YOUR INSTRUMENT PANEL This feature allows you to plug an iPod into the Connecting The iPod vehicle’s sound system through a 16–pin connector, using Use the provided connection cable to connect an iPod to the provided interface cable. the vehicle’s 16–pin connector port (which is located in the glove compartment on some vehicles).
Page 263: Using This Feature
UNDERSTANDING YOUR INSTRUMENT PANEL 263 Using This Feature Play Mode By using the provided connection cable to connect an When switched to UCI mode, the iPod automatically iPod to the vehicle’s UCI 16–pin connector port: starts Play mode. In Play mode, you may use the following buttons on the radio faceplate to control the •...
Page 264 264 UNDERSTANDING YOUR INSTRUMENT PANEL • Jump backward in the current track by pressing and • While a track is playing, press the INFO button to see holding the << RW button. Holding the << RW the associated metadata (artist, track title, album, etc.) button long enough will take you to the beginning for that track.
Page 265: List Or Browse Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 265 • RND button (available on sales code RES radio only): knob fast will scroll through the list faster. During Pressing this button toggles between Shuffle ON and fast scroll, you may notice a slight delay in updating Shuffle OFF modes for the iPod .
Page 266 266 UNDERSTANDING YOUR INSTRUMENT PANEL • Pressing a PRESET button will display the current CAUTION! list on the top line and the first item in that list on • Leaving the iPod (or any supported device) any- the second line. where in the vehicle in extreme heat or cold can •...
Page 267: Uconnect™ Studios (Satellite Radio) - If Equipped (Ren/Rer/Rbz/Res Radios Only)
UNDERSTANDING YOUR INSTRUMENT PANEL 267 uconnect™ studios (SATELLITE RADIO) — IF information, call the toll-free number 888-539-7474, or EQUIPPED (REN/RER/RBZ/RES RADIOS ONLY) visit the Sirius web site at www.sirius.com, or at www- Satellite radio uses direct satellite-to-receiver broadcast- .siriuscanada.ca for Canadian residents. ing technology to provide clear digital sound, coast to Electronic Serial Number/Sirius Identification coast.
Page 268: Selecting Uconnect™ Studios (Satellite) Mode
268 UNDERSTANDING YOUR INSTRUMENT PANEL Sirius ID number will display. The Sirius ID number bikes should be placed as far rearward as possible, within display will time out in two minutes. Press any button on the loading design of the rack. Do not place items directly the radio to exit this screen.
Page 269: Operating Instructions - Uconnect™ Studios (Satellite) Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 269 Operating Instructions - uconnect™ studios INFO Button (Satellite) Mode Pressing the INFO button will cycle the display informa- tion between Artist, Song Title, and Composer (if avail- NOTE: The ignition switch must be in the ON or ACC able).
Page 270 270 UNDERSTANDING YOUR INSTRUMENT PANEL MUSIC TYPE Button SETUP Button Pressing this button once will turn on the Music Type Pressing the SETUP button allows you to select the mode for five seconds. Pressing the MUSIC TYPE button following items: or turning the TUNE/SCROLL control knob within five •...
Page 271: Operating Instructions - Uconnect™ Phone (If Equipped)
UNDERSTANDING YOUR INSTRUMENT PANEL 271 You may add a second channel to each pushbutton by VIDEO ENTERTAINMENT SYSTEM (VES)™ — IF repeating the above procedure with this exception: Press EQUIPPED the SET button twice and SET 2 will show in the display The optional Video Entertainment System (VES)™...
Page 272 272 UNDERSTANDING YOUR INSTRUMENT PANEL The LCD screen is located in the overhead compartment console. VES™ Remote Control Location NOTE: Refer to your VES™ User’s Manual for detailed operating instructions. Overhead Video Screen NOTE: Refer to the “uconnect™ studios” section of uconnect™...
Page 273: Remote Sound System Controls - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 273 REMOTE SOUND SYSTEM CONTROLS — IF The right hand control is a rocker type switch with a EQUIPPED pushbutton in the center. Pressing the top of the switch The remote sound system controls are located on the rear will increase the volume, and pressing the bottom of the surface of the steering wheel.
Page 274: Cd Player
274 UNDERSTANDING YOUR INSTRUMENT PANEL The button located in the center of the left hand control 1. Handle the disc by its edge; avoid touching the will tune to the next pre-set station that you have surface. programmed in the radio pre-set pushbuttons. 2.
Page 275: Radio Operation And Cellular Phones
UNDERSTANDING YOUR INSTRUMENT PANEL 275 oversized, or have protection encoding. Try a known Manual Heating and Air Conditioning System good disc before considering disc player service. The controls for the manual heating and air conditioning system in this vehicle consist of a series of outer rotary RADIO OPERATION AND CELLULAR PHONES dials and inner push knobs.
Page 276 276 UNDERSTANDING YOUR INSTRUMENT PANEL Front Blower Control temperatures. Rotating the knob clockwise, into the red There are four blower speeds. Use this area, indicates warmer temperatures. control to regulate the amount of air NOTE: If your air conditioning performance seems forced through the system in any lower than expected, check the front of the A/C con- mode you select.
Page 277 UNDERSTANDING YOUR INSTRUMENT PANEL 277 Panel Mode Mix Mode Air is directed through the outlets in the instrument Air is directed through the floor, defrost and side panel. These outlets can be adjusted to direct airflow. window demist outlets. This setting works best in cold or snowy conditions that require extra heat at Bi-Level Mode the windshield.
Page 278 278 UNDERSTANDING YOUR INSTRUMENT PANEL • In cold or damp weather, the use of the Recirculation Recirculation Control Press this button to choose between mode will cause windows to fog on the inside because outside air intake or recirculation of of moisture buildup inside the vehicle.
Page 279: Automatic Temperature Control (Atc)
UNDERSTANDING YOUR INSTRUMENT PANEL 279 Economy Mode MAX A/C If ECONOMY mode is desired, press the A/C button to For maximum cooling, when MAX turn off the LED indicator and the A/C compressor. A/C is selected the A/C is turned on Rotate the temperature control knob to the desired automatically and the air is recircu- temperature.
Page 280 280 UNDERSTANDING YOUR INSTRUMENT PANEL knobs on the control unit and a comfort temperature setting by using the temperature up and down but- tons. • The system provides set-and-forget operation for op- timum comfort and convenience. • The system can be controlled manually, if desired. •...
Page 281 UNDERSTANDING YOUR INSTRUMENT PANEL 281 Automatic Operation NOTE: • It is not necessary to move the temperature settings for 1. Position the MODE control knob to the Auto position cold or hot vehicles. The system automatically adjusts on the Automatic Temperature Control (ATC) Panel. the temperature, mode and fan speed to provide 2.
Page 282 282 UNDERSTANDING YOUR INSTRUMENT PANEL Manual Operation selected. This allows the front occupants to control the This system offers a full complement of manual override volume of air circulated in the vehicle and cancel the features. Auto mode. NOTE: Each of these features operate independently The operator can also select the direction of the airflow from each other.
Page 283 UNDERSTANDING YOUR INSTRUMENT PANEL 283 Floor Mode The Air Conditioning (A/C) button allows the Air comes from the floor outlets. A slight amount of operator to manually activate or deactivate the air air is directed through the defrost and side window conditioning system.
Page 284: Summer Operation
284 UNDERSTANDING YOUR INSTRUMENT PANEL Recirculation mode should only be used temporarily. The Winter Operation recirculation LED will illuminate on the blower control To ensure the best possible heater and defroster perfor- knob when this button is selected. Push the button a mance, make sure the engine cooling system is function- second time to turn off the Recirculation mode LED and ing properly and the proper amount, type, and concen-...
Page 285: Window Fogging And Frosting
UNDERSTANDING YOUR INSTRUMENT PANEL 285 Window Fogging and Frosting Outside Air Intake Vehicle windows tend to fog on the inside of the glass in Make sure the air intake, located directly in front of the mild, rainy and/or humid weather. Windows may frost windshield, is free of obstructions such as leaves.
Page 286: Operating Tips
286 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips...
Page 287: Starting And Operating
STARTING AND OPERATING CONTENTS ▫ Brake/Transmission Interlock Manual Starting Procedures ....293 Override ......297 ▫...
Page 288 288 STARTING AND OPERATING ▫ Transfer Case Position Indicator Light ..314 ▫ Crossing Obstacles (Rocks And Other High Points) ......333 ▫...
Page 289 STARTING AND OPERATING 289 Winch Usage (Power Wagon Only) — Electronic Brake Control System ... 377 If Equipped ......351 ▫...
Page 290 290 STARTING AND OPERATING ▫ Tire Inflation Pressures ....399 ▫ Dual Rear Wheels ....409 ▫...
Page 291 STARTING AND OPERATING 291 ▫ MMT In Gasoline ....422 ▫ Maintenance ......428 ▫...
Page 292 292 STARTING AND OPERATING ▫ Recreational Towing – Four-Wheel Drive Snowplow ......449 Models ......451 Recreational Towing (Behind Motorhome, Etc.) .
Page 293: Starting Procedures
STARTING AND OPERATING 293 STARTING PROCEDURES Normal Starting Before starting your vehicle, adjust your seat, adjust both Normal starting of either a warm or cold engine is inside and outside mirrors, and fasten your seat belt. obtained without pumping or depressing the accelerator pedal.
Page 294: If Engine Fails To Start
294 STARTING AND OPERATING Tip Start Feature WARNING! Do not press the accelerator. Turn the ignition switch • Never pour fuel or other flammable liquids into briefly to the START position and release it. The starter motor will continue to run but will automatically disen- the throttle body air inlet opening in an attempt to gage when the engine is running.
Page 295: After Starting
STARTING AND OPERATING 295 If the engine has been flooded, it may start to run, but not 1500 Models have enough power to continue running when the key The engine block heater cord is routed under the hood on fob is released. If this occurs, continue cranking with the the passenger side of the vehicle near the right head lamp accelerator pedal pushed all the way to the floor.
Page 296: Automatic Transmission
296 STARTING AND OPERATING WARNING! CAUTION! (Continued) • Do not shift from REVERSE, PARK, or NEUTRAL Remember to disconnect the cord before driving. into any forward gear when the engine is above Damage to the 110-115 Volt electrical cord could cause idle speed.
Page 297: Key Ignition Park Interlock
STARTING AND OPERATING 297 Key Ignition Park Interlock Brake/Transmission Interlock Manual Override This vehicle is equipped with a Key Ignition Park Inter- Column Shifter — If Equipped lock which requires the shift lever to be placed in PARK There is an override for the BTSI that allows you to move prior to turning the key fob to the LOCK position.
Page 298 298 STARTING AND OPERATING 5. Using the screwdriver, press and hold the override tab Center Console Shifter — If Equipped through the access port (ringed circle) on the bottom of There is an override for the BTSI that allows you to move the steering column.
Page 299: Four-Speed Automatic Transmission - If Equipped
STARTING AND OPERATING 299 Four–Speed Automatic Transmission — If Equipped NOTE: Under extremely cold temperatures (-6°F (-21°C) and when in DRIVE, transmission operation may be briefly limited to only second gear operation. Normal operation will resume once the transmission temperature has risen to a suitable level.
Page 300 300 STARTING AND OPERATING Never use PARK while the vehicle is in motion. Apply REVERSE the parking brake when leaving the vehicle in this range. This range is for moving the vehicle rearward. Use this Always apply the parking brake first, then place the shift range only after the vehicle has come to a complete stop.
Page 301 STARTING AND OPERATING 301 • vehicle speed is above approximately 30 mph 2 (Second) (48 km/h) This range is for moderate grades and to assist braking on dry pavement or in mud and snow. Begins at a stop in • the TOW/HAUL switch has not been activated low gear with automatic upshift to second gear.
Page 302 302 STARTING AND OPERATING The transmission will downshift from OVERDRIVE to DRIVE if the accelerator pedal is fully pressed at vehicle speeds above approximately 35 mph (56 km/h). When To Use TOW/HAUL Mode When driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting oc- curs, press the TOW/HAUL switch.
Page 303 STARTING AND OPERATING 303 Transmission Limp Home Mode If the problem is no longer detected, the transmission will Transmission function is monitored for abnormal condi- return to normal operation. If the problem persists, tions. If a condition is detected that could result in PARK, REVERSE, and NEUTRAL will continue to oper- transmission damage, the Transmission Limp Home ate.
Page 304: Five-Speed Automatic Transmission - If Equipped
304 STARTING AND OPERATING Five–Speed Automatic Transmission — If into 3 (third gear), the transmission will never shift above Equipped third gear, but can shift down to 2 (second gear) or 1 (first The shift lever display located in the instrument panel gear), when needed.
Page 305 STARTING AND OPERATING 305 through third gear are underdrive gears, and fourth gear is direct drive. ERS fifth gear (Overdrive) is the same as the normal fourth gear. When in the DRIVE position in first through fourth gear, the first tap down (-), will display the ERS designation for the current gear (the transmission will not downshift).
Page 306 306 STARTING AND OPERATING Gear Ranges WARNING! Do not race the engine when shifting from PARK or NEUTRAL position into another gear range. Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their PARK grip and the vehicle could skid.
Page 307 STARTING AND OPERATING 307 REVERSE WARNING! (Continued) This range is for moving the vehicle rearward. Use this • Your vehicle could move and injure you and others range only after the vehicle has come to a complete stop. if it is not completely in PARK. Check by trying to NEUTRAL move the shift lever back and forth without first This range is for when the vehicle is standing for pro-...
Page 308 308 STARTING AND OPERATING Overdrive Operation operation at this temperature. Normal operation will The Overdrive automatic transmission contains an elec- resume when the transmission fluid temperature has tronically controlled fourth and fifth gear (Overdrive). risen to a suitable level. The transmission will automatically shift from DRIVE to If the transmission temperature gets extremely hot, the Overdrive if the following conditions are present: transmission will automatically select the most desirable...
Page 309 STARTING AND OPERATING 309 performance and reduce the potential for transmission closed-throttle downshifts to third gear are performed overheating or failure due to excessive shifting. When (for improved braking) when driving conditions warrant. operating in the TOW/HAUL mode, fifth gear is dis- The “TOW/HAUL Indicator Light”...
Page 310: Four-Wheel Drive Operation - If Equipped
310 STARTING AND OPERATING NOTE: FOUR-WHEEL DRIVE OPERATION — IF • The torque converter clutch will not engage until the EQUIPPED transmission fluid and engine coolant (antifreeze) are Four-wheel drive trucks are equipped with either a warm [usually after 1 to 3 miles (1.6 to 4.8 km) of manually shifted transfer case or an electronically shifted driving].
Page 311 STARTING AND OPERATING 311 When additional traction is required, the 4H and 4L When operating your vehicle in 4L, the engine speed is positions can be used to lock the front and rear drive- approximately three times that of the 2H or 4H positions shafts together and force the front and rear wheels to at a given road speed.
Page 312 312 STARTING AND OPERATING NOTE: Delayed shifts out of four-wheel drive may be For additional information on the appropriate use of each experienced due to uneven tire wear, low or uneven tire transfer case mode position see the information below: pressures, excessive vehicle loading, or cold tempera- tures.
Page 313: Shifting Procedure - Manually Shifted Transfer Case
STARTING AND OPERATING 313 2H or 4H ⇔ 4L Four-Wheel Drive Low Range - This range locks the front With the vehicle rolling at 2 to 3 mph (3 to 5 km/h), shift and rear driveshafts together forcing the front and rear the transmission into NEUTRAL.
Page 314: Transfer Case Position Indicator Light
314 STARTING AND OPERATING method is with the vehicle rolling 2 to 3 mph (3 to 5 km/h). Avoid attempting to engage or disengage 4L with the vehicle moving faster than 2 to 3 mph (3 to 5 km/h). • Do not attempt to shift into or from 4L while the transmission is in gear.
Page 315 STARTING AND OPERATING 315 This electronically shifted transfer case is designed to be hand corner of the 4WD Control Switch. The transfer case driven in the two-wheel drive position (2WD) for normal NEUTRAL position is to be used for recreational towing street and highway conditions on dry, hard surfaced only.
Page 316 316 STARTING AND OPERATING If one or more shift conditions are not met: WARNING! 1. The indicator light for the current position will remain Always engage the parking brake when powering down the vehicle if the “SVC 4WD Warning Light” is 2.
Page 317 STARTING AND OPERATING 317 Proper operation of four-wheel drive vehicles depends For additional information on the appropriate use of each on tires of equal size, type and circumference on each transfer case mode position, see the information below: wheel. Any difference in tire size can cause damage to the transfer case.
Page 318: Shifting Procedure
318 STARTING AND OPERATING • If all the requirements to select a new transfer case Neutral - This range disengages both the front and rear position have been met, the current position indicator driveshafts from the powertrain. To be used for flat light will turn OFF, the selected position indicator light towing behind another vehicle.
Page 319 STARTING AND OPERATING 319 NOTE: The four-wheel drive system will not allow 2. Shift the transmission into NEUTRAL. shifts between 2WD/4WD LOCK if the front and/or rear 3. While still rolling, rotate the transfer case control wheels are spinning (no traction). In this situation, the switch to the desired position.
Page 320: Electronically Shifted Transfer Case (Five-Position Switch) - If Equipped
320 STARTING AND OPERATING NOTE: • If Steps 1 or 2 of either the Preferred or Alternate Procedure are not satisfied prior to attempting the shift, then the desired position indicator light will flash continuously while the original position indicator light is ON, until all requirements have been met.
Page 321 STARTING AND OPERATING 321 • Four-wheel drive low range (4WD LOW) When additional traction is required, the transfer case 4WD LOCK and 4WD LOW positions can be used to lock • Neutral (NEUTRAL) the front and rear driveshafts together forcing the front This electronically shifted transfer case is designed to be and rear wheels to rotate at the same speed.
Page 322 322 STARTING AND OPERATING Transfer Case Position Indicator Lights 2. The newly selected position indicator light will con- The Transfer Case Position Indicator Lights (4WD, tinue to flash. 4LOW, and 4WD AUTO) are located on the instrument 3. The transfer case will not shift. cluster and indicate the current and desired transfer case selection.
Page 323 STARTING AND OPERATING 323 Proper operation of four-wheel drive vehicles depends WARNING! on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the Always engage the parking brake when powering transfer case.
Page 324: Shifting Procedure
324 STARTING AND OPERATING For additional information on the appropriate use of each 4WD LOW transfer case mode position see the information below: Four-Wheel Drive Low Range - This range provides low speed four-wheel drive. Locks the front and rear drive- shafts together forcing the front and rear wheels to rotate Rear-Wheel Drive High Range - This range is for normal at the same speed.
Page 325 STARTING AND OPERATING 325 position indicator light will continue to flash until all disengage faster if you momentarily release the accelera- the requirements for the selected position have been tor pedal after turning the control switch. If the vehicle is met.
Page 326: Axle Locker System (2500 Models Only) - If Equipped
326 STARTING AND OPERATING 3. While still rolling, rotate the transfer case control in process, the desired position indicator light will flash switch to the desired position. continuously while the original position indicator light is ON, until all requirements have been met. 4.
Page 327 STARTING AND OPERATING 327 the ground. It is not recommended to drive the vehicle The locking axles are controlled by the axle locker switch. with the differentials locked on pavement due to the The switch has three positions, AXLE UNLOCK, REAR reduced ability to turn and speed limitations.
Page 328 328 STARTING AND OPERATING To lock the rear axle, place the vehicle in 4LO. Refer to To lock the front axle; move the axle locker switch to “Four Wheel Drive Operation” in this section of the FRONT/REAR LOCK while traveling less than 3 mph manual.
Page 329: Safe Off-Road Driving - Power Wagon Only
STARTING AND OPERATING 329 To unlock the rear axle; move the axle locker switch to Skid Plates And Underbody Protection AXLE UNLOCK. The REAR LOCK indicator light will go Steel skid plates protect the major driveline components out when the rear axle is unlocked. of the truck including the fuel tank, transfer case and steering damper.
Page 330 330 STARTING AND OPERATING Water Fording Characteristics vehicle from jerking or lurching. This technique is also used when you need to stop and restart a vehicle on a Water fording characteristic is the vehicle’s ability to cross steep incline. a body of still water, where the powertrain and drivetrain are safe from water ingestion.
Page 331: Driving In Snow, Mud And Sand
STARTING AND OPERATING 331 use 4L (Low Range) in rain, ice, snow, mud, sand, to get CAUTION! heavy loads rolling, improve traction, or whenever 4H (High Range) traction will not do the job. Never park your vehicle over dry grass or other combustible materials.
Page 332 332 STARTING AND OPERATING no more than a ⁄ turn quickly back and forth, while hole, get out and determine how deep it is, if there are still applying throttle. This will allow the tires to get a any hidden obstacles and if the vehicle can be safely fresh bite and help maintain your momentum.
Page 333: Crossing Obstacles (Rocks And Other High Points)
STARTING AND OPERATING 333 forward until it makes contact with the object. Apply the CAUTION! throttle lightly while holding a light brake pressure and ease the vehicle up and over the object. Reduced tire pressures may cause tire unseating and total loss of air pressure.
Page 334 334 STARTING AND OPERATING Crossing Large Rocks vehicle’s mobility. Approach these obstacles at a 45- When approaching large rocks, choose a path which degree angle and let each tire go through the obstacle ensures you drive over the largest with your tires. This independently.
Page 335: Hill Climbing
STARTING AND OPERATING 335 Crossing Logs and place a few rocks under the tires so the weight is off To cross a log, approach it at a slight angle (approxi- of the high point when you let the vehicle down. You can mately 10 to 15 degrees).
Page 336 336 STARTING AND OPERATING • Before Climbing A Steep Hill – As you approach a all four tires back on the ground. As you approach the hill consider its grade or steepness. Determine if it is crest of the hill ease off the throttle and slowly proceed too steep.
Page 337 STARTING AND OPERATING 337 • Driving Down Hill – Before driving down a steep hill WARNING! you need to determine if it is too steep for a safe descent. What is the surface traction? Is the grade too Do not descend a steep grade in NEUTRAL. Use steep to maintain a slow controlled descent? Are there vehicle brakes in conjunction with engine braking.
Page 338: Driving Through Water
338 STARTING AND OPERATING WARNING! WARNING! Driving across an incline increases the risk of a If the engine stalls or you lose headway or cannot rollover, which may result in severe injury. make it to the top of a steep hill or grade, never attempt to turn around.
Page 339 STARTING AND OPERATING 339 your vehicle’s abilities and be able to recover it if CAUTION! something goes wrong. You should never stop or shut a vehicle off when crossing deep water unless you ingested Water ingestion into the axles, transmission, transfer water into the engine air intake.
Page 340 340 STARTING AND OPERATING crossing is the water depth, current and bottom con- CAUTION! ditions. On soft bottoms the vehicle will sink in, effectively increasing the water level on the vehicle. Be Muddy waters can reduce the cooling system effec- sure to consider this when determining the depth and tiveness by depositing debris onto the radiator.
Page 341: Airing Down For Off-Road Driving
STARTING AND OPERATING 341 downstream out of control if the water is deep enough form to the ground contour. Different terrain, tires, and to push on the large surface area of the vehicle’s body. vehicles require different tire pressure. Hard surfaces like Before you proceed determine the speed of the current, rock and heavier vehicles require higher pressures than the water’s depth, approach angle, bottom condition...
Page 342: Vehicle Recovery
342 STARTING AND OPERATING Vehicle Recovery vehicle impingement on the surroundings, then using a If you drive off-road, you may encounter a situation tow strap to the vehicle tow hooks would be fast and where you will need to recover your vehicle. Vehicle easy.
Page 343 STARTING AND OPERATING 343 • Rock Cycling Your Vehicle – Rock cycling your ve- CAUTION! hicle is one of the easiest, fastest and most commonly used methods. This simply involves shifting your Damage can occur when spinning your tires at an vehicle from DRIVE to REVERSE, while applying excessive high speed.
Page 344 344 STARTING AND OPERATING straps together using a 1 ⁄ inch hard wood dowel. WARNING! This will keep the straps from becoming knotted and is safer than using a clevis pin if the strap breaks. Next Never use tow straps with end hooks or link two have the tow vehicle backup, leaving two to three feet straps with a clevis pin.
Page 345 STARTING AND OPERATING 345 out of the situation in a slow controlled manner. This the vehicle in first gear and apply a very light throttle control works well for avoiding further vehicle dam- as you power the winch in. Be careful not to allow age.
Page 346: After Driving Off-Road
346 STARTING AND OPERATING • After extended operation in mud, sand, water, or After Driving Off-Road Off-road operation puts more stress on your vehicle than similar dirty conditions, have brake drums and rotors, does most on-road driving. After driving off-road, it is brake linings, and axle yokes inspected and cleaned as always a good idea to check for damage.
Page 347: Limited-Slip Differential - If Equipped
STARTING AND OPERATING 347 LIMITED-SLIP DIFFERENTIAL – IF EQUIPPED WARNING! The limited-slip differential provides additional traction on snow, ice, mud, sand and gravel, particularly when On vehicles equipped with a limited-slip differential there is a difference between the traction characteristics never run the engine with one rear wheel off the of the surface under the right and left rear wheels.
Page 348: Driving On Slippery Surfaces
348 STARTING AND OPERATING DRIVING ON SLIPPERY SURFACES DRIVING THROUGH WATER When driving on wet or slushy roads, it is possible for a Driving through water more than a few inches/ wedge of water to build up between the tire and road centimeters deep will require extra caution to ensure surface.
Page 349: Shallow Standing Water
STARTING AND OPERATING 349 Shallow Standing Water CAUTION! (Continued) Although your vehicle is capable of driving through • Driving through standing water may cause dam- shallow standing water, consider the following Caution age to your vehicle’s drivetrain components. Al- and Warning before doing so. ways inspect your vehicle’s fluids (i.e., engine oil, transmission/transaxle, axle, etc.) for signs of con- CAUTION!
Page 350: Driving Off-Road
350 STARTING AND OPERATING DRIVING OFF-ROAD WARNING! Care should be taken when attempting to climb steep • Driving through standing water limits your vehi- hills or driving diagonally across a hill or slope. If natural obstacles force you to travel diagonally up or down a hill, cle’s traction capabilities.
Page 351: Winch Usage (Power Wagon Only) - If Equipped
STARTING AND OPERATING 351 NOTE: After off-road usage, particularly in sand or WINCH USAGE (POWER WAGON ONLY) — IF mud, inspect the underside of the vehicle for accumu- EQUIPPED lated dirt at the propeller shaft, axles, U-joints, brake Things To Know Before Using Your Winch rotors and calipers.
Page 352 352 STARTING AND OPERATING 2. Attach the hook to a suitable anchor point. Low Voltage Interrupt Your winch is equipped with a device that will interrupt CAUTION! winch function if the vehicle charging system voltage drops to a low level. The winch will not power-in or out Be certain the anchor will withstand the load re- for 30 seconds if this device is tripped.
Page 353: Understanding The Features Of Your Winch
STARTING AND OPERATING 353 Understanding The Features Of Your Winch Winch Components...
Page 354 354 STARTING AND OPERATING 1. Motor: The winch motor is powered by the vehicle 6. Clutch Lever: The clutch lever allows the winch drum charging system and features a thermal protection switch to be disconnected from the winch motor to allow the that automatically stops motor function in the power-in wire rope to be pulled from the winch by hand.
Page 355: Winch Accessories
STARTING AND OPERATING 355 Winch Accessories Snatch/Block Pulley: Used properly, the multi-purpose The following accessories are necessary to attach the snatch block allows you to (1) winch to anchors, change direction of pull, and for safe increase the winch’s pulling winching.
Page 356: Operating Your Winch
356 STARTING AND OPERATING Clevis/D-Shackles: Operating Your Winch D-Shackle is a safe means of WARNING! connecting the looped ends of cables, straps and snatch • Always use supplied hook strap to hold the hook blocks. The shackle’s pin is when spooling wire rope in or out. threaded to allow easy re- •...
Page 357 STARTING AND OPERATING 357 WARNING! (Continued) WARNING! (Continued) • Always keep hands and clothing clear of the wire • Never winch when there are less than five wraps rope, hook and fairlead opening during operation of wire rope around the winch drum. •...
Page 358 358 STARTING AND OPERATING General Information Vehicle Recovery Using the Winch Practice using your winch before you get stuck. Some key CAUTION! points to remember when using your winch are: • Always Know Your Winch: Take the time to fully 1.
Page 359 STARTING AND OPERATING 359 CAUTION! (Continued) • Always keep remote control lead clear of the drum, wire rope and rigging. • Inspect for cracks, pinches, frayed wires, or loose connections. Replace if damaged. • Be careful not to pull the Winch Cable Collar through the rollers.
Page 360 360 STARTING AND OPERATING 3. Disengage the clutch to allow free spooling of the winch drum, rotate the clutch lever on the winch to disengage. Freespooling conserves battery power. Hook Strap 5. Pull the wire to the anchor point. Pull out enough wire rope to reach your anchor point.
Page 361 STARTING AND OPERATING 361 6. Secure to the anchor point. Once you have established Tree Trunk Protector your anchor point, secure the tree-trunk protector or CAUTION! choker-chain around the object. Always be certain the anchor you select will with- stand the load.
Page 362 362 STARTING AND OPERATING NOTE: How to choose an anchor point: A secure anchor is critical to winching operations. An anchor must be strong enough to hold while winching. Natural an- chors include trees, stumps and rocks. Hook the cable as low as possible.
Page 363 STARTING AND OPERATING 363 9. Connect the remote control to the winch control box, 10. Put wire rope under tension. Using the remote con- located behind the front bumper. Be careful not to let the trol switch, slowly wind the wire rope until no slack remote control cord dangle in front of the winch.
Page 364 364 STARTING AND OPERATING 12. Check wire rope. The wire rope should be neatly 13. In certain situations you wound around the spooling drum. Improper winding may decide to throw a heavy can cause damage to the wire rope. blanket or similar object over the wire rope.
Page 365 STARTING AND OPERATING 365 the vehicle and never near the wire rope or snatch For additional assistance, the winched vehicle can be block. Your situation may have other no people zones. slowly driven while being pulled by the winch. Continue pulling until the vehicle is on stable ground.
Page 366 366 STARTING AND OPERATING NOTE: So, line up pulls as straight ahead as possible and stop • Avoid overheating the winch motor. For extended winching if the wire rope comes close to the tie rods or winching, stop at reasonable intervals to allow the mounting plate.
Page 367 STARTING AND OPERATING 367 NOTE: How to spool under no load: Arrange the remote control lead so it cannot be caught in the winch. Arrange the wire rope so it will not kink or tangle when spooled. Be sure any wire rope already on the spooling drum is wound tightly and evenly layered.
Page 368: Rigging Techniques
368 STARTING AND OPERATING 19. Store the hook on the most outboard loop of the tow NOTE: Always store the remote control in a protected, hook. clean, dry area. Rigging Techniques Various winching situations will require application of other winching techniques. These could range from too little distance to achieve maximum pull using straight line rigging, simply increasing pulling power, or main- taining a straight-line pulling situation.
Page 369 STARTING AND OPERATING 369 How to Change the Pulling Direction All winching operations should have a straight line from the winch to the object being pulled. This minimizes the wire rope collecting on one side of the drum affecting pulling efficiency and damaging wire rope. A snatch block, secured to a point directly in front of the vehicle will enable you to change your pulling direction while still allowing the wire rope to be at 90°...
Page 370: Power Steering
370 STARTING AND OPERATING Double Line vehicle’s frame/tow hook and run the wire rope through a snatch block. Disengage the clutch and, using the snatch block, pull out enough wire to reach your anchor point. Do not attach the hook to the mounting kit. Secure to the anchor point with a tree trunk protector or choker chain.
Page 371: Power Steering Fluid Check
STARTING AND OPERATING 371 NOTE: CAUTION! • Increased noise levels at the end of the steering wheel travel are considered normal and do not indicate that Prolonged operation of the steering system at the end there is a problem with the power steering system. of the steering wheel travel will increase the steering fluid temperature and it should be avoided when •...
Page 372: Parking Brake
372 STARTING AND OPERATING If necessary, add fluid to restore to the proper indicated CAUTION! level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to “Fluids, Lubricants, and Genuine Do not use chemical flushes in your power steering Parts”...
Page 373 STARTING AND OPERATING 373 WARNING! • Always fully apply the parking brake when leav- ing your vehicle or it may roll and cause damage or injury. Also be certain to leave the transmission in PARK. Failure to do so may allow the vehicle to roll and cause damage or injury.
Page 374: Brake System
374 STARTING AND OPERATING When parking on a hill, turn the front wheels toward the 3500 Dual Rear Wheel Models Only curb on a downhill grade and away from the curb on an The brake system power assist is provided by a hydro- uphill grade.
Page 375: Four-Wheel Anti-Lock Brake System
STARTING AND OPERATING 375 Four-Wheel Anti-Lock Brake System The system’s pump motor runs during an ABS stop to provide regulated hydraulic pressure. The pump motor WARNING! makes a low humming noise during operation. This is normal. The Four-Wheel Anti-Lock Brake System contains The ABS conducts a low-speed selftest at about 10 mph sophisticated electronic equipment.
Page 376 376 STARTING AND OPERATING ABS Warning Light WARNING! (Continued) The ABS includes an amber warning light. When the light • The ABS cannot prevent accidents, including is illuminated, the ABS is not functioning. The system those resulting from excessive speed in turns, reverts to standard, non-anti-lock brakes.
Page 377: Electronic Brake Control System
STARTING AND OPERATING 377 ELECTRONIC BRAKE CONTROL SYSTEM WARNING! Your vehicle is equipped with an advanced electronic • ABS cannot prevent the natural laws of physics brake control system that includes Anti-Lock Brake Sys- tem (ABS), Traction Control System (TCS), Brake Assist from acting on the vehicle, nor can it increase System (BAS), Hill Start Assist (HSA), Electronic Stability braking or steering efficiency beyond that af-...
Page 378: Traction Control System (Tcs)
378 STARTING AND OPERATING Traction Control System (TCS) Brake Assist System (BAS) The TCS monitors the amount of wheel spin of each of The BAS is designed to optimize the vehicle’s braking the driven wheels. If wheel spin is detected, brake capability during emergency braking maneuvers.
Page 379: Hill Start Assist (Hsa)
STARTING AND OPERATING 379 Hill Start Assist (HSA) WARNING! The HSA system is designed to assist the driver in • The BAS cannot prevent the natural laws of phys- launching a vehicle on an incline. HSA will maintain the level of brake pressure the driver inputs for a short ics from acting on the vehicle, nor can it increase duration once the driver takes his foot off of the brake braking efficiency beyond that afforded by the...
Page 380 380 STARTING AND OPERATING HSA Activation Criteria The system will only work if the intended direction of the The following criteria must be met in order for HSA to vehicle and vehicle gear match. For example, if the activate: intended direction is forward up a hill and the vehicle is in DRIVE and the activation criteria are met, HSA will •...
Page 381 STARTING AND OPERATING 381 TOW/HAUL switch is activated and compensates by WARNING! (Continued) releasing brake pressure at a slower rate while throttle is • HSA is not a parking brake. If you stop the vehicle applied in order to prevent the vehicle from rolling down on a hill without putting the transmission in the hill.
Page 382: Electronic Stability Program (Esp)
382 STARTING AND OPERATING 3. With the engine running and the brake applied, rotate EVIC Equipped Vehicles the steering wheel 180° counterclockwise from center. HSA is a Customer Programmable Feature on a EVIC equipped vehicle. If you wish to turn off the HSA feature, 4.
Page 383 STARTING AND OPERATING 383 • Oversteer - when the vehicle is turning more than appropriate for the steering wheel position. • Understeer - when the vehicle is turning less than appropriate for the steering wheel position. ESP/TCS Indicator Light The “ESP/TCS Indicator Light” located in the instrument cluster, starts to flash as soon as the tires lose traction and the ESP system becomes active.
Page 384 384 STARTING AND OPERATING (2WD/4WD AUTO/4WD LOCK/4WD LOW/ WARNING! NEUTRAL) transfer case. If you have a four-wheel drive • ESP cannot prevent the natural laws of physics vehicle, and want to determine which transfer case is on your vehicle and how to operate it, refer to the “Four from acting on the vehicle, nor can it increase the Wheel Drive Operation”...
Page 385 STARTING AND OPERATING 385 ESP Partial Off overcome, turn ESP back on by momentarily pressing the This mode is entered by momentarily depressing the ESP ESP OFF switch. This may be done while the vehicle is in OFF switch. When in Partial Off mode, the TCS portion motion.
Page 386 386 STARTING AND OPERATING the ESP OFF switch for five seconds when the vehicle is mode, described above. When the vehicle speed drops stopped and the engine is running. After five seconds, the below 35 mph (56 km/h) the ESP system shuts off. ESP is “ESP/TCS Indicator Light”...
Page 387 STARTING AND OPERATING 387 this light remains on after several ignition cycles and the WARNING! vehicle has been driven several miles/kilometers at speeds greater than 30 mph (48 km/h), see your autho- With the ESP switched off, the enhanced vehicle rized dealer as soon as possible to have the problem stability offered by ESP is unavailable.
Page 388: Trailer Sway Control (Tsc)
388 STARTING AND OPERATING Trailer Sway Control (TSC) TSC is only active in the default “ESP On” mode. TSC can The TSC system uses sensors in the vehicle to recognize be disabled by pressing the ESP OFF switch and entering an excessively swaying trailer and will take the appro- “ESP Partial Off”...
Page 389: Tire Safety Information
STARTING AND OPERATING 389 TIRE SAFETY INFORMATION NOTE: • P (Passenger) - Metric tire sizing is based on U.S. Tire Markings design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. •...
Page 390 390 STARTING AND OPERATING • Temporary spare tires are high-pressure compact • High flotation tire sizing is based on U.S. design spares designed for temporary emergency use only. standards and it begins with the tire diameter molded Tires designed to this standard have the letter “T” into the sidewall.
Page 391 STARTING AND OPERATING 391 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ..blank..= Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm)
Page 392 392 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
Page 393: Tire Identification Number (Tin)
STARTING AND OPERATING 393 Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall The TIN may be found on one or both sides of the tire, tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side.
Page 394: Tire Loading And Tire Pressure
394 STARTING AND OPERATING Tire Loading and Tire Pressure This placard tells you important information about the: Tire Placard Location 1) number of people that can be carried in the vehicle NOTE: The proper cold tire inflation pressure is listed 2) total weight your vehicle can carry on the driver’s side B-Pillar.
Page 395 STARTING AND OPERATING 395 NOTE: Under a maximum loaded vehicle condition, Steps for Determining Correct Load Limit gross axle weight ratings (GAWRs) for the front and rear 1. Locate the statement “The combined weight of occu- axles must not be exceeded. For further information on pants and cargo should never exceed XXX lbs or XXX kg”...
Page 396 396 STARTING AND OPERATING 5. Determine the combined weight of luggage and cargo NOTE: • The following table shows examples on how to calcu- being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity late total load, cargo/luggage, and towing capacities calculated in Step 4.
Page 397 STARTING AND OPERATING 397...
Page 398: Tires - General Information
398 STARTING AND OPERATING Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause accidents. recommended load capacity for your vehicle.
Page 399: Tire Inflation Pressures
STARTING AND OPERATING 399 Tire Inflation Pressures WARNING! (Continued) The proper cold tire inflation pressure is listed on the • Unequal tire pressures from one side of the ve- driver’s side “B” Pillar. hicle to the other can cause the vehicle to drift to Some vehicles may have Supplemental Tire Pressure the right or left.
Page 400 400 STARTING AND OPERATING Tire pressures change by approximately 1 psi (7 kPa) per CAUTION! 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in After inspecting or adjusting the tire pressure, al- the Winter.
Page 401: Tire Pressures For High Speed Operation
STARTING AND OPERATING 401 Tire Pressures for High Speed Operation Radial Ply Tires The manufacturer advocates driving at safe speeds WARNING! within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle...
Page 402: Tire Spinning
402 STARTING AND OPERATING original equipped tire on the front or rear axle of your Tire Spinning vehicle, but it is not. Installation of this limited-use spare When stuck in mud, sand, snow, or ice conditions, do not tire affects vehicle handling. Since it is not the same tire, spin your vehicle’s wheels faster than 30 mph (48 km/h) replace (or repair) the original tire and reinstall on the or for longer than 30 seconds continuously without...
Page 403: Tread Wear Indicators
STARTING AND OPERATING 403 Tread Wear Indicators becomes 1/16 in (2 mm). When the tread is worn to the Tread wear indicators are in the original equipment tires tread wear indicators, the tire should be replaced. to help you in determining when your tires should be Life of Tire replaced.
Page 404: Replacement Tires
404 STARTING AND OPERATING Keep dismounted tires in a cool, dry place with as little WARNING! exposure to light as possible. Protect tires from contact • Do not use a tire, wheel size or rating other than with oil, grease, and gasoline. that specified for your vehicle.
Page 405: Supplemental Tire Pressure Information - If Equipped
STARTING AND OPERATING 405 SUPPLEMENTAL TIRE PRESSURE INFORMATION WARNING! (Continued) — IF EQUIPPED • Failure to equip your vehicle with tires having A light load vehicle condition is defined as two passen- adequate speed capability can result in sudden tire gers [150 lbs (68 kg) each] plus 200 lbs (91 kg) of cargo.
Page 406 406 STARTING AND OPERATING CAUTION! CAUTION! (Continued) • Do not drive for a prolonged period on dry pave- To avoid damage to your vehicle, tires or chains, ment. observe the following precautions: • Observe the tire chain manufacturer’s instructions • Because of limited chain clearance between tires on method of installation, operating speed, and and other suspension components, it is important conditions for usage.
Page 407 STARTING AND OPERATING 407 NOTE: CAUTION! • The use of class “S” chains is permitted with P245/ 70R17 tires only. Do not use tire chains on 4x4 model trucks equipped with P265/70R17, LT275/70R17, P275/60R20, tires. • The use of class “U” chains is permitted on the front There may not be adequate clearance for the chains and rear of 4X4, 2500 model trucks with LT245/ and you are risking structural or body damage to...
Page 408: Snow Tires
408 STARTING AND OPERATING SNOW TIRES These effects can be reduced by timely rotation of tires. Snow tires should be of the same size and type construc- The benefits of rotation are especially worthwhile with tion as the front tires. Consult the manufacturer of the aggressive tread designs such as those on all season type snow tire to determine any maximum vehicle speed tires.
Page 409: Dual Rear Wheels
STARTING AND OPERATING 409 Dual Rear Wheels Tire Rotation Tire Rotation The tires used on dual wheel assemblies should be matched for wear to prevent overloading one tire in a set. To check if tires are even, lay a straight edge across all four tires.
Page 410: Tire Pressure Monitor System (Tpms)
410 STARTING AND OPERATING TIRE PRESSURE MONITOR SYSTEM (TPMS) CAUTION! The Tire Pressure Monitoring System (TPMS) will warn the driver of a low tire pressure based on the vehicle 3500 Dual Rear Tires have only one approved direc- recommended cold tire inflation placard pressure. The tion of rotation.
Page 411 STARTING AND OPERATING 411 pressure will also increase as the vehicle is driven - this is have been received. The vehicle may need to be driven normal and there should be no adjustment for this for up to 20 minutes above 15 mph (25 km/h) to receive increased pressure.
Page 412 412 STARTING AND OPERATING NOTE: CAUTION! • The TPMS is not intended to replace normal tire care • The TPMS has been optimized for the original and maintenance, nor to provide warning of a tire failure or condition. equipment tires and wheels. TPMS pressures have been established for the tire size equipped on your •...
Page 413: Tire Pressure Monitor System Components
STARTING AND OPERATING 413 • Seasonal temperature changes will affect tire pressure, Tire Pressure Monitoring Low Pressure Warnings and the TPMS will monitor the actual tire pressure in The Tire Pressure Monitoring Telltale Lamp will the tire. illuminate in the instrument cluster, and an au- dible chime will be activated when one or more of Tire Pressure Monitor System Components the four active road tire pressures are low.
Page 414 414 STARTING AND OPERATING Check TPMS Warnings 6. Loss of communication with the tire pressure moni- The “Tire Pressure Monitoring Telltale Light” located in toring sensors. the instrument cluster will flash on and off for 75 seconds NOTE: Your vehicle is equipped with a non-matching and will remain on solid when a system fault is detected.
Page 415: Tire Pressure Monitor System (Tpms) Tire Light Load Inflation Switch Description (2500 Models) - If Equipped
STARTING AND OPERATING 415 4. For each subsequent ignition key cycle, a chime will Tire Pressure Monitor System (TPMS) Tire Light sound and the “TPM Telltale Light” will flash on and off Load Inflation Switch Description (2500 Models) – for 75 seconds and then remain on solid. If Equipped 5.
Page 416 416 STARTING AND OPERATING The TPMS tire light load inflation switch will allow the driver to switch between the max load inflation pressure (cold) low pressure warning threshold and the light load inflation pressure (cold) low pressure warning threshold depending on the vehicle’s load condition. The Tire and Loading Information label defines the recommended front and rear cold tire inflation pressures for the vehicle when operating in the Max Load condition.
Page 417 STARTING AND OPERATING 417 also equipped to be driven with tire pressures appro- priate to either a Light Load condition or the vehicle Max Load condition. • The tire light load inflation switch will allow the driver to change between the max load inflation pressure (cold) low pressure warning threshold and the light load inflation pressure (cold) low pressure warning threshold depending on the vehicle’s load condition.
Page 418 418 STARTING AND OPERATING Tire Pressure Information label. The Supplemental Tire the rear face of the driver door. Using an accurate tire Pressure Information label is located on the rear face of pressure gauge, re-check the tire pressures for the light the driver door.
Page 419: General Information
STARTING AND OPERATING 419 • This device may not cause harmful interference. the max load inflation pressure (cold) values to switch the TPMS system to the max load inflation pressure • This device must accept any interference received, (cold) low pressure warning threshold. If after pressing including interference that may cause undesired the tire light load inflation switch, and tire pressures are operation.
Page 420: 5.7L Engine
420 STARTING AND OPERATING gasoline is not recommended, as it will not provide any as hard starting, stalling, and hesitations. If you experi- benefit over regular gasoline in these engines. ence these symptoms, try another brand of gasoline before considering service for the vehicle. 5.7L Engine The 5.7L engine is designed to meet all Over 40 auto manufacturers worldwide have issued and...
Page 421: Gasoline/Oxygenate Blends
STARTING AND OPERATING 421 The manufacturer supports the use of reformulated gaso- Problems that result from using methanol/gasoline lines. Properly blended reformulated gasolines will pro- blends are not the responsibility of the manufacturer. vide excellent performance and durability for the engine While MTBE is an oxygenate made from Methanol, it and fuel system components.
Page 422: Mmt In Gasoline
422 STARTING AND OPERATING To fix a Non-FFV vehicle inadvertently fueled once with life and reduces emissions system performance in some E-85 perform the following: vehicles. The manufacturer recommends that gasoline without MMT be used in your vehicle. The MMT content •...
Page 423: Fuel System Cautions
STARTING AND OPERATING 423 Fuel System Cautions CAUTION! (Continued) • The use of fuel additives, which are now being CAUTION! sold as octane enhancers are not recommended. Follow these guidelines to maintain your vehicle’s Most of these products contain high concentra- performance: tions of methanol.
Page 424: Carbon Monoxide Warnings
424 STARTING AND OPERATING Carbon Monoxide Warnings WARNING! (Continued) • Guard against carbon monoxide with proper WARNING! maintenance. Have the exhaust system inspected Carbon monoxide (CO) in exhaust gases is deadly. every time the vehicle is raised. Have any abnor- Follow the precautions below to prevent carbon mal conditions repaired promptly.
Page 425: Ethanol Fuel (E-85)
STARTING AND OPERATING 425 E-85 Fuel Cap E-85 Badge Ethanol Fuel (E-85) CAUTION! E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. Only vehicles with the E-85 fuel filler door label can operate on E-85.
Page 426: Fuel Requirements
426 STARTING AND OPERATING • you drive the vehicle immediately after refueling for at WARNING! least 5 miles (8 km) Ethanol vapors are extremely flammable and could Observing these precautions will avoid possible hard cause serious personal injury. Never have any smok- starting and/or significant deterioration in driveability ing materials lit in or near the vehicle when remov- during warm up.
Page 427: Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles
STARTING AND OPERATING 427 Selection Of Engine Oil For Flexible Fuel Vehicles NOTE: Use of the engine block heater (if equipped) is (E-85) and Gasoline Vehicles beneficial for E-85 startability when the ambient tempera- FFV vehicles operated on E-85 require specially formu- ture is less than 32°F (0°C).
Page 428: Maintenance
428 STARTING AND OPERATING CAUTION! Replacing fuel system components with non-ethanol compatible components can damage your vehicle. Maintenance If you operate the vehicle using E-85 fuel, follow the maintenance schedule section of this manual. CAUTION! Do not use ethanol mixture greater than 85% in your vehicle.
Page 429 STARTING AND OPERATING 429 CAUTION! WARNING! (Continued) • Never add fuel to the vehicle when the engine is • Damage to the fuel system or emissions control running. system could result from using an improper fuel • A fire may result if gasoline is pumped into a tank filler tube cap (gas cap).
Page 430: Loose Fuel Filler Cap Message
430 STARTING AND OPERATING Loose Fuel Filler Cap Message This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), Gross Axle Weight If the vehicles diagnostic system determines that the fuel Rating (GAWR) front and rear, and Vehicle Identification filler cap in loose, improperly installed, or damaged, a Number (VIN).
Page 431 STARTING AND OPERATING 431 Gross Axle Weight Rating (GAWR) Rim Size The GAWR is the maximum permissible load on the front This is the rim size that is appropriate for the tire size and rear axles. The load must be distributed in the cargo listed.
Page 432: Trailer Towing
432 STARTING AND OPERATING Loading Improper weight distributions can have an adverse effect The actual total weight and the weight of the front and on the way your vehicle steers and handles and the way rear of your vehicle at the ground can best be determined the brakes operate.
Page 433: Common Towing Definitions
STARTING AND OPERATING 433 To maintain warranty coverage, follow the requirements measure GTW is to put your fully loaded trailer on a and recommendations in this manual concerning ve- vehicle scale. The entire weight of the trailer must be hicles used for trailer towing. supported by the scale.
Page 434 434 STARTING AND OPERATING that typically provides adjustable friction associated with WARNING! the telescoping motion to dampen any unwanted trailer swaying motions while traveling. It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition Weight-Carrying Hitch can result if either rating is exceeded.
Page 435 STARTING AND OPERATING 435 safety. The addition of a friction/hydraulic sway control also dampens sway caused by traffic and crosswinds and contributes positively to tow vehicle and trailer stability. Trailer sway control and a weight distributing (load equalizing) hitch are recommended for heavier Tongue Weights (TW) and may be required depending on vehicle and trailer configuration/loading to comply with GAWR requirements.
Page 436 436 STARTING AND OPERATING EXAMPLE — With Weight-Distributing Hitch (Correct) EXAMPLE — Improper Adjustment of Weight- Distributing Hitch (Incorrect) Fifth-Wheel Hitch The fifth-wheel hitch is a special high platform with a coupling that mounts over the rear axle of the tow vehicle in the truck bed.
Page 437: Trailer Hitch Classification
STARTING AND OPERATING 437 Gooseneck Hitch Weight Ratings)” for the website address that contains The gooseneck hitch employs a pivoted coupling arm the necessary information for your specific drivetrain. which attaches to a ball mounted in the bed of a pickup Trailer Hitch Classification Definitions truck.
Page 438: Trailer Towing Weights (Maximum Trailer Weight Ratings)
• http:// www.dodge.com. • http:// www.dodge.ca (Canada). Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the GTW Consider the following items when computing the on the tow hitch of your vehicle.
Page 439: Towing Requirements
STARTING AND OPERATING 439 • The weight of any other type of cargo or equipment CAUTION! put in or on your vehicle • Avoid towing a trailer for the first 500 miles • The weight of the driver and all passengers. (805 km) of vehicle operation.
Page 440 440 STARTING AND OPERATING Vehicles with trailers should not be parked on a grade. WARNING! (Continued) When parking, apply the parking brake on the tow • Make certain that the load is secured in the trailer vehicle. Put the tow vehicle transmission in PARK. With and will not shift during travel.
Page 441 STARTING AND OPERATING 441 • When replacing tires, refer to “Tires–General Informa- 4. Tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve the tion” for proper tire replacement procedures. Replac- 10% to 15% range of tongue weight as a percentage of ing tires with a higher load carrying capacity will not total trailer weight).
Page 442 442 STARTING AND OPERATING CAUTION! WARNING! (Continued) • Towing any trailer will increase your stopping If the trailer weighs more than 1,000 lbs (454 kg) distance. When towing you should allow for addi- loaded, it should have its own brakes and they tional space between your vehicle and the vehicle should be of adequate capacity.
Page 443 STARTING AND OPERATING 443 This display may also be used to display diagnostic information, if needed. • SC — Short Circuit to Ground • Sb — Short to Battery • CF — Controller Fault – If this message appears on the display, see your authorized dealer.
Page 444 444 STARTING AND OPERATING The trailer and the vehicle’s brake lamps will come on GAIN setting can be increased to a maximum of 10 or when either vehicle braking or manual trailer brakes are decreased to a minimum of 0 (no trailer braking). applied.
Page 445 STARTING AND OPERATING 445 3. When a trailer with electric brakes is plugged in, the EVIC Display Messages GAIN setting will illuminate. The trailer brake control interacts with the Electronic Vehicle Information Center (EVIC). Display messages, 4. Use the GAIN adjustment (+/-) buttons to increase or along with a single chime, will be displayed when a decrease the GAIN setting to the desired starting point.
Page 446 446 STARTING AND OPERATING The Trailer Tow Package will include a four and seven- WARNING! pin wiring harness. Use a factory approved trailer har- ness and connector. Connecting a trailer that is not compatible with the ITBM system may result in reduced or complete loss NOTE: Do not cut or splice wiring into the vehicle’s of trailer braking.
Page 447 STARTING AND OPERATING 447 Four-Pin Connector Seven-Pin Connector 1 — Female Pins 4 — Park 1 — Battery 5 — Ground 2 — Male Pin 5 — Left Stop/Turn 2 — Backup Lamps 6 — Left Stop/Turn 3 — Ground 6 —...
Page 448: Towing Tips
448 STARTING AND OPERATING NOTE: Using “TOW/HAUL” mode or a lower gear WARNING! range while operating the vehicle under heavy operating conditions will improve performance and extend trans- Any work done to the vehicle’s electrical system or mission life by reducing excessive shifting and heat build wiring should be performed by a qualified automo- up.
Page 449: Snowplow
STARTING AND OPERATING 449 Electronic Speed Control — If Equipped − Air Conditioning Turn off temporarily. − Do not use in hilly terrain or with heavy loads. SNOWPLOW − When using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until NOTE: Do not use this model vehicle for snowplow you can get back to cruising speed.
Page 450: Recreational Towing (Behind Motorhome, Etc.)
450 STARTING AND OPERATING RECREATIONAL TOWING (BEHIND CAUTION! MOTORHOME, ETC.) Using this vehicle for snowplow applications can CAUTION! cause damage to the vehicle. Front or rear wheel lifts should not be used. Internal WARNING! damage to the transmission or transfer case will occur if a front or rear wheel lift is used when recreational Attaching a snowplow to this vehicle could adversely towing.
Page 451: Models
STARTING AND OPERATING 451 Recreational Towing – Four-Wheel Drive Models WARNING! CAUTION! You or others could be injured if you leave the vehicle unattended with the transfer case in the Failure to follow these requirements can cause severe NEUTRAL position without first fully engaging the damage to the transmission and/or transfer case.
Page 452 452 STARTING AND OPERATING 1. Bring the vehicle to a complete stop. 13. Attach the vehicle to the tow vehicle with the tow bar. 2. Shut OFF the engine. 14. Release the parking brake. 3. Press the brake pedal. CAUTION! 4.
Page 453 STARTING AND OPERATING 453 4. Press the brake pedal. CAUTION! 5. Shift the transmission into NEUTRAL. • Do not use a bumper-mounted clamp-on tow bar 6. Shift the transfer case lever into desired position. on your vehicle. The bumper face bar will be damaged.
Page 454 454 STARTING AND OPERATING Recreational Towing Procedure — Electronic Shift CAUTION! Transfer Case — If Equipped Use the following procedure to prepare your vehicle for It is necessary to follow these steps to be certain that recreational towing: the transfer case is fully in NEUTRAL before recre- ational towing to prevent damage to internal parts.
Page 455 STARTING AND OPERATING 455 7. After the shift is completed and the NEUTRAL light NOTE: • Steps 1 through 5 are requirements that must be met comes on, release the NEUTRAL button. prior to pressing the NEUTRAL button, and must 8.
Page 456 456 STARTING AND OPERATING 5. Shift the transmission into NEUTRAL. CAUTION! 6. Press the transfer case switch NEUTRAL button for Damage to the transmission may occur if the trans- one second. mission is shifted into PARK with the transfer case in 7.
Page 457 STARTING AND OPERATING 457 requirements (with the exception of step 3 - key ON) WARNING! are not met prior to pressing the NEUTRAL button, or are no longer met during the one second time, then all You or others could be injured if you leave the of the mode position indicator lights will flash con- vehicle unattended with the transfer case in the tinuously until all requirements are met or until the...
Page 458: Equipment Identification Plate
458 STARTING AND OPERATING EQUIPMENT IDENTIFICATION PLATE CAUTION! The equipment Identification Plate is located on the hood • Do not use a bumper-mounted clamp-on tow bar inner surface. on your vehicle. The bumper face bar will be The following information about your vehicle is dis- damaged.
Page 459: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....460 Hoisting ......480 Jacking And Tire Changing .
Page 460: Hazard Warning Flasher
460 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER JACKING AND TIRE CHANGING The Hazard Warning flasher switch is located on the WARNING! upper switch bank just below the radio. • Being under a jacked-up vehicle is dangerous. The Press the switch to turn on the Hazard Warning flasher.
Page 461: Jack Location
WHAT TO DO IN EMERGENCIES 461 Jack Location The jack and jack tools are stored under the front passenger seat. Removal To access the jack and jack tools you must remove the plastic access cover, located on the side of the seat. To remove the cover, pull the front part of the cover (closest to the front of the seat) toward you to release a locking tab.
Page 462 462 WHAT TO DO IN EMERGENCIES Remove the jack and tools by removing the wing bolt and sliding the assembly from under the seat. Jack and Tools (2500/3500 Series) Jack and Tools (1500 Series)
Page 463 WHAT TO DO IN EMERGENCIES 463 WARNING! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience abrupt stopping, rapid accelera- tion or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury.
Page 464 464 WHAT TO DO IN EMERGENCIES 3. Fold the flap and roll the jack tool kit into a cylindrical package (in direction of arrows) and tie to the jack using the tie straps. Tying Bag to Jack with Straps Folding Flap and Rolling Bag...
Page 465 WHAT TO DO IN EMERGENCIES 465 4. Place the jack and tools in the storage position holding the jack by the jack turn-screw, slip the jack and tools under the seat so that the bottom slot engages into the fastener on the floor, and then secure to the floor pan using the wing bolt.
Page 466: Removing The Spare Tire
466 WHAT TO DO IN EMERGENCIES mechanism tube. Rotate the wheel wrench handle coun- terclockwise until the spare tire is on the ground with enough cable slack to allow you to pull it out from under the vehicle. When the spare is clear, tilt the retainer at the end of the cable and pull it through the center of the wheel.
Page 467: Preparations
WHAT TO DO IN EMERGENCIES 467 NOTE: The winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch. Preparations 1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas.
Page 468: Instructions
468 WHAT TO DO IN EMERGENCIES 4. Turn the ignition OFF. Instructions 5. Turn on the Hazard Warning flasher. WARNING! 6. Block both the front and rear of the Carefully follow these tire changing warnings to wheel diagonally opposite the jacking help prevent personal injury or damage to your position.
Page 469 WHAT TO DO IN EMERGENCIES 469 WARNING! (Continued) • Do not let anyone sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack. • Only use the jack in the positions indicated and Jack Warning Label for lifting this vehicle during a tire change.
Page 470 470 WHAT TO DO IN EMERGENCIES 3. Placement of the jack: • 1500 Series Trucks When changing a front wheel, place the scissors jack under the rear portion of the lower control arm as shown below. 4X4 Jacking Location Operate the jack using the jack drive tube and the wheel wrench.
Page 471 WHAT TO DO IN EMERGENCIES 471 For 4x2 and 4x4 trucks, when changing a rear wheel, Connect the jack tube extension and wheel wrench. assemble the jack drive tube to the jack and connect the CAUTION! drive tube to the extension tube. Place the jack under the axle between the wheel and the shock bracket with the Before raising the wheel off the ground, make sure drive tubes extending to the rear.
Page 472 472 WHAT TO DO IN EMERGENCIES • 2500/3500 Series Trucks Operate the jack using the jack drive tube and the wheel For 2500/3500 4x2 series trucks, when changing a front wrench. The tube extension, may be used, but is not wheel, place the bottle jack under the frame rail behind required.
Page 473 WHAT TO DO IN EMERGENCIES 473 4x4 Jacking Location Rear Jacking Location (All) For 4x2 and 4x4 trucks, when changing a rear wheel, Connect the jack tube extension and wheel wrench. assemble the jack drive tube to the jack and connect the drive tube to the extension tube.
Page 474 474 WHAT TO DO IN EMERGENCIES 5. Remove the wheel nuts and pull the wheel off. On CAUTION! single rear-wheel (SRW) trucks, install the spare wheel and wheel nuts with the cone shaped end of the wheel Before raising the wheel off the ground, make sure nuts toward the wheel.
Page 475: Hub Caps/Wheel Covers - If Equipped
WHAT TO DO IN EMERGENCIES 475 NOTE: Do not oil wheel studs. For chrome wheels, do WARNING! not substitute with chrome plated wheel nuts. A loose tire or jack thrown forward in a collision or Hub Caps/Wheel Covers — If Equipped hard stop could injure someone in the vehicle.
Page 476: Wheel Nuts
476 WHAT TO DO IN EMERGENCIES nut bolt circle and strike the high side down with a CAUTION! rubber mallet. Be sure that the hub caps and wheel skins • Use a back-and-forth motion to remove the hub are firmly seated around the wheel. cap.
Page 477 WHAT TO DO IN EMERGENCIES 477 Disc Type Nut Stud Size Torque Torque Wheels Ft. Lbs. Newton Meters Cone 9/16-18 120-150 160-200 Flanged 9/16-18 130-160 190-220 8-Stud — Dual Rear Wheels Dual wheels are flat-mounted and center-piloted. The lug nuts are a two-piece assembly. When the tires are being rotated or replaced, clean these lug nuts and add two drops of oil at the interface between the hex and the washer.
Page 478 478 WHAT TO DO IN EMERGENCIES Dual wheel models require a special heavy-duty lug nut These dual rear wheels should be tightened as follows: tightening adapter (included with the vehicle) to cor- rectly tighten the lug nuts. Also, when it is necessary to remove and install dual rear wheels, use a proper vehicle lifting device.
Page 479: To Stow The Flat Or Spare
WHAT TO DO IN EMERGENCIES 479 second time to verify that specific torque has been WARNING! achieved. Retighten to specifications at 100 miles (160 km) and after 500 miles (800 km). A loose tire thrown forward in a collision or hard stop could injure the occupants in the vehicle.
Page 480: Hoisting
480 WHAT TO DO IN EMERGENCIES HOISTING can be dangerous if done improperly, so follow this A conventional floor jack may be used at the jacking procedure carefully. locations. Refer to the graphics that show jacking loca- WARNING! tions. However, a floor jack or frame hoist must never be used on any other parts or the underbody.
Page 481 WHAT TO DO IN EMERGENCIES 481 3. Turn off the heater, radio, and all unnecessary electri- WARNING! (Continued) cal loads. • A battery generates hydrogen gas which is flam- 4. Connect one end of a jumper cable to the positive mable and explosive.
Page 482: With Portable Starting Unit
482 WHAT TO DO IN EMERGENCIES WARNING! WARNING! • Do not connect the cable to the negative post of the Any procedure other than above could result in: • Personal injury caused by electrolyte squirting out discharged battery. The resulting electrical spark could cause the battery to explode and could result the battery vent.
Page 483: Freeing A Stuck Vehicle
WHAT TO DO IN EMERGENCIES 483 Allow the engine to idle with the transmission shift lever CAUTION! in NEUTRAL for at least one minute after every five rocking-motion cycles. This will minimize overheating It is very important that the starting unit operating and reduce the risk of transmission failure during pro- voltage does not exceed 12-Volts DC or damage to the longed efforts to free a stuck vehicle.
Page 484: Emergency Tow Hooks - If Equipped
484 WHAT TO DO IN EMERGENCIES WARNING! WARNING! • Chains are not recommended for freeing a stuck Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause damage, or vehicle. Chains may break, causing serious injury even failure, of the axle and tires.
Page 485: Towing A Disabled Vehicle
WHAT TO DO IN EMERGENCIES 485 TOWING A DISABLED VEHICLE The manufacturer recommends towing with all wheels Proper towing or lifting equipment is required to prevent OFF the ground. Acceptable methods are to tow the damage to your vehicle. Use only tow bars and other vehicle on a flatbed or with one end of vehicle raised and equipment designed for the purpose, following equip- the opposite end on a towing dolly.
Page 486 486 WHAT TO DO IN EMERGENCIES If the vehicle is to be towed faster than 30 mph (50 km/h) CAUTION! or more than 15 miles (25 km) the vehicle must be towed with the rear wheels raised and the front wheels on the Towing faster than 30 mph (50 km/h) or for more than ground.
Page 487 MAINTAINING YOUR VEHICLE CONTENTS Engine Compartment — 3.7L ... . . 490 Maintenance Procedures ....496 ▫...
Page 488 488 MAINTAINING YOUR VEHICLE ▫ Windshield Wiper Blades ....504 Vehicle Storage ..... . . 529 ▫...
Page 489 MAINTAINING YOUR VEHICLE 489 ▫ Engine ......543 Fluids And Capacities ....541 ▫...
Page 490: Engine Compartment - 3.7L
490 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 3.7L 1 — Air Cleaner Filter 7 — Washer Fluid Reservoir 2 — Automatic Transmission Dipstick (If Equipped) 8 — Power Steering Fluid Reservoir 3 — Engine Oil Dipstick 9 — Engine Oil Fill 4 —...
Page 491: Engine Compartment - 4.7L
MAINTAINING YOUR VEHICLE 491 ENGINE COMPARTMENT — 4.7L 1 — Air Cleaner Filter 7 — Washer Fluid Reservoir 2 — Automatic Transmission Dipstick 8 — Power Steering Fluid Reservoir 3 — Engine Oil Dipstick 9 — Engine Oil Fill 4 — Brake Fluid Reservoir 10 —...
Page 492: Engine Compartment - 5.7L
492 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 5.7L 1 — Air Cleaner Filter 7 — Washer Fluid Reservoir 2 — Automatic Transmission Dipstick 8 — Integrated Power Module 3 — Engine Oil Fill 9 — Power Steering Fluid Reservoir 4 — Engine Oil Dipstick 10 —...
Page 493: Onboard Diagnostic System (Obd Ii)
MAINTAINING YOUR VEHICLE 493 ONBOARD DIAGNOSTIC SYSTEM (OBD II) CAUTION! Your vehicle is equipped with a sophisticated onboard diagnostic system called OBDII. This system monitors Prolonged driving with the MIL on could cause the performance of the emissions, engine, and automatic further damage to the emission control system.
Page 494: Emissions Inspection And Maintenance Programs
494 MAINTAINING YOUR VEHICLE will appear the next time the vehicle is started. This serviced, recently had a dead battery or a battery replace- might indicate a damaged cap. If the problem is detected ment. If the OBD II system should be determined not twice in a row, the system will turn on the MIL.
Page 495: Replacement Parts
MAINTAINING YOUR VEHICLE 495 5. Approximately 15 seconds later, one of two things will Regardless of whether your vehicle’s OBD II system is happen: ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced a.
Page 496: Maintenance Procedures
496 MAINTAINING YOUR VEHICLE your vehicle. Refer to these manuals before attempting Besides those maintenance items specified in the fixed any procedure yourself. maintenance schedule, there are other components which may require servicing or replacement in the future. NOTE: Intentional tampering with emissions control systems may void your warranty and could result in civil CAUTION! penalties being assessed against you.
Page 497: Engine Oil
MAINTAINING YOUR VEHICLE 497 The best time to check the engine oil level is about five CAUTION! (Continued) minutes after a fully warmed up engine is shut off. • Your vehicle has been built with improved fluids Checking the oil while the vehicle is on level ground will that protect the performance and durability of improve the accuracy of the oil level readings.
Page 498 498 MAINTAINING YOUR VEHICLE Change Engine Oil American Petroleum Institute (API) Engine Oil The oil change indicator system will remind you that it is Identification Symbol time to take your vehicle in for scheduled maintenance. This symbol means that the oil has Refer to the “Maintenance Schedule”...
Page 499 MAINTAINING YOUR VEHICLE 499 Engine Oil Viscosity (SAE Grade) NOTE: For 2500/3500 trucks with a 5.7L engine oper- SAE 5W-20 engine oil is recommended for all operating ating under a gross combined weight rating of 14,000 lbs temperatures. This engine oil improves low temperature (6 350 kg) or greater, SAE 5W-30 engine oil is recom- starting and vehicle fuel economy.
Page 500: Engine Oil Filter
500 MAINTAINING YOUR VEHICLE indiscriminately discarded, can present a problem to the WARNING! environment. Contact your authorized dealer, service station or governmental agency for advice on how and The air induction system (air cleaner, hoses, etc.) can where used oil and oil filters can be safely discarded in provide a measure of protection in the case of engine your area.
Page 501: Maintenance-Free Battery
MAINTAINING YOUR VEHICLE 501 Maintenance-Free Battery WARNING! (Continued) The top of the maintenance-free battery is permanently • Battery posts, terminals and related accessories sealed. You will never have to add water or is periodic contain lead and lead compounds. Wash hands maintenance required.
Page 502: Air Conditioner Maintenance
502 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance WARNING! For best possible performance, your air conditioner • Use only refrigerants and compressor lubricants should be checked and serviced by an authorized dealer at the start of each warm season. This service should approved by the manufacturer for your air condi- include cleaning of the condenser fins and a performance tioning system.
Page 503: Front Prop Shaft Lubrication - 2500/3500
MAINTAINING YOUR VEHICLE 503 NOTE: Use only manufacturer approved A/C System Body Lubrication Sealers, Stop Leak Products, Seal Conditioners, Compres- Locks and all body pivot points, including such items as sor Oil, or Refrigerants. seat tracks, door hinge pivot points and rollers, liftgate, tailgate, sliding doors and hood hinges, should be lubri- Refrigerant Recovery and Recycling cated periodically with a lithium based grease, such as...
Page 504: Windshield Wiper Blades
504 MAINTAINING YOUR VEHICLE amount of a high quality lubricant, such as MOPAR performance of blades may be present with chattering, Lock Cylinder Lubricant or equivalent directly into the marks, water lines or wet spots. If any condition is lock cylinder. present please proceed to clean wiper blades with humid cloth removing any debris that may be affecting its Windshield Wiper Blades...
Page 505: Exhaust System
MAINTAINING YOUR VEHICLE 505 The washer fluid reservoir will hold a full gallon of fluid Exhaust System when the Low Washer Fluid Light illuminates. The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust WARNING! system.
Page 506 506 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- WARNING! verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure Exhaust gases can injure or kill. They contain carbon proper catalyst operation and prevent possible catalyst monoxide (CO) which is colorless and odorless.
Page 507 MAINTAINING YOUR VEHICLE 507 NOTE: Intentional tampering with emissions control To minimize the possibility of catalyst damage: systems can result in civil penalties being assessed • Do not shut off the engine or interrupt the ignition against you. when the transmission is in gear and the vehicle is in motion.
Page 508: Cooling System
508 MAINTAINING YOUR VEHICLE Cooling System Check the coolant recovery bottle tubing for brittle rub- ber, cracking, tears, cuts and tightness of the connection WARNING! at the bottle and radiator. Inspect the entire system for leaks. You or others can be badly burned by hot coolant or With the engine at normal operating temperature (but steam from your radiator.
Page 509 MAINTAINING YOUR VEHICLE 509 Refer to the “Maintenance Schedule” in Section 8 for CAUTION! (Continued) proper maintenance intervals. • Do not use water alone or alcohol-based engine Selection Of Coolant coolant (antifreeze) products. Do not use addi- Use only the manufacturer’s recommended engine cool- tional rust inhibitors or antirust products, as they ant (antifreeze).
Page 510 510 MAINTAINING YOUR VEHICLE Please review these recommendations for using Hybrid Please note that it is the owner’s responsibility to main- Organic Additive Technology (HOAT) engine coolant tain the proper level of protection against freezing ac- (antifreeze). cording to the temperatures occurring in the area where the vehicle is operated.
Page 511 MAINTAINING YOUR VEHICLE 511 rules for your community. To prevent ingestion by ani- WARNING! mals or children do not store ethylene glycol-based • The warning words “DO NOT OPEN HOT” on engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground.
Page 512 512 MAINTAINING YOUR VEHICLE When additional engine coolant (antifreeze) is needed to coolant (antifreeze) needs to be added, contents of maintain the proper level, it should be added to the coolant recovery bottle must also be protected against coolant bottle. Do not overfill. freezing.
Page 513: Brake System
MAINTAINING YOUR VEHICLE 513 • Do not change the thermostat for Summer or Winter Brake Fluid Level Check operation. If replacement is ever necessary, install The fluid level of the master cylinder should be checked ONLY the correct type thermostat. Other designs may when performing under the hood service or immediately result in unsatisfactory engine coolant (antifreeze) per- if the brake system warning lamp indicates system...
Page 514 514 MAINTAINING YOUR VEHICLE WARNING! WARNING! (Continued) • To avoid contamination from foreign matter or • Use only manufacturer’s recommended brake moisture, use only new brake fluid or fluid that fluid. Refer to “Fluids, Lubricants, and Genuine has been in a tightly closed container. Keep the Parts”...
Page 515: Rear Axle And 4X4 Front Driving Axle Fluid Level
MAINTAINING YOUR VEHICLE 515 For all 2500/3500 Model axles, the fluid level should be WARNING! (Continued) 1/4” ± 1/4 in (6.4 mm ± 6.4 mm) below the fill hole on • Do not allow petroleum based fluid to contami- the 9.25 in front and 3/4 in ± 1/4 in (19 mm ± 6.4 mm) on nate the brake fluid.
Page 516: Transfer Case
516 MAINTAINING YOUR VEHICLE Limited-Slip Differentials This vehicle requires that Fluid Level Check 4 oz. (118 ml) MOPAR Limited Slip Additive or equiva- This fluid level can be checked by removing the filler lent be added to the gear lubricant. Refer to “Fluids, plug.
Page 517 MAINTAINING YOUR VEHICLE 517 the proper tools to ensure that the fluid level is set CAUTION! properly. The fluid level should be checked when the • Do not use chemical flushes in your transmission engine is fully warmed up and the fluid in the transmis- sion is at normal operating temperature.
Page 518 518 MAINTAINING YOUR VEHICLE 2. The vehicle must be on level ground. NOTE: If it is necessary to check the transmission below the operating temperature, the fluid level should be 3. Fully apply the parking brake and press the brake between the two “COLD”...
Page 519: Appearance Care And Protection From Corrosion
MAINTAINING YOUR VEHICLE 519 To prevent dirt and water from entering the transmission Special Additives after checking or replenishing fluid, make certain that the Automatic Transmission Fluid (ATF) is an engineered dipstick cap is properly reseated. It is normal for the product and its performance may be impaired by supple- dipstick cap to spring back slightly from its fully seated mental additives.
Page 520 520 MAINTAINING YOUR VEHICLE hot or cold weather and other extreme conditions will Washing have an adverse affect on paint, metal trim, and under- • Wash your vehicle regularly. Always wash your ve- body protection. hicle in the shade using MOPAR Car Wash or equiva- The following maintenance recommendations will enable lent, or a mild car wash soap and rinse the panels you to obtain maximum benefit from the corrosion...
Page 521 MAINTAINING YOUR VEHICLE 521 • If your vehicle is damaged due to an accident or CAUTION! similar cause which destroys the paint and protective coating, have your vehicle repaired as soon as pos- Do not use abrasive or strong cleaning materials such sible.
Page 522 522 MAINTAINING YOUR VEHICLE • For tough stains, apply MOPAR heavy soil and/or excessive brake dust, use MOPAR Total Clean or Wheel Cleaner or equivalent or select a nonabrasive, equivalent, or a mild soap solution to a clean, damp non-acidic cleaner. Do not use scouring pads, steel wool, cloth and remove stain.
Page 523 MAINTAINING YOUR VEHICLE 523 Your leather upholstery can be best preserved by regular Cleaning Headlights cleaning with a damp soft cloth. Small particles of dirt Your vehicle is equipped with plastic headlights and fog can act as an abrasive and damage the leather upholstery lights (if equipped) that are lighter and less susceptible to and should be removed promptly with a damp cloth.
Page 524: Fuses
524 MAINTAINING YOUR VEHICLE cleaner. Use caution when cleaning the inside rear win- Seat Belt Maintenance dow equipped with electric defrosters or the right rear Do not bleach, dye or clean the belts with chemical quarter window equipped with the radio antenna. Do solvents or abrasive cleaners.
Page 525 MAINTAINING YOUR VEHICLE 525 cover, otherwise the cavity number of each fuse is Cavity Cartridge Mini Description stamped on the inside cover that corresponds to the Fuse Fuse following chart. 30 Amp Bat — Presafe #1 Pink 30 Amp Bat — Trailer Tow Pink Main 25 Amp...
Page 526 526 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Description Cavity Cartridge Mini Description Fuse Fuse Fuse Fuse 30 Amp Bat — DTCM/Axle 40 Amp Frt HVAC Motor Pink Locks Green 30 Amp Bat — Plg/Electric 25 Amp Bat — Sunroof/ Pink Brake Natural Skylight...
Page 527 MAINTAINING YOUR VEHICLE 527 Cavity Cartridge Mini Description Cavity Cartridge Mini Description Fuse Fuse Fuse Fuse 20 Amp Bat — Trlr Tow BUX/ 20 Amp Fr/Rr Washer Yellow Yellow 10 Amp Bat — J1962 Diag/ 15 Amp Bat — NGC/EATX/ Mirrors Blue 10 Amp...
Page 528 528 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Description Cavity Cartridge Mini Description Fuse Fuse Fuse Fuse 25 Amp Rear Wiper 10 Amp IGN R-H/Lamp Natural Wash/HVAC/Park Assist/Ir Sns 15 Amp IOD-SDARS/VES Blue 2–3/DVD/HFM/ 20 Amp IGN R/ACC-Pwr UGDO/Vanity Lamp Yellow Outlet #2 10 Amp IOD-HVAC, U/Hood...
Page 529: Vehicle Storage
MAINTAINING YOUR VEHICLE 529 Cavity Cartridge Mini Description CAUTION! (Continued) Fuse Fuse • When replacing a blown fuse, it is important to 20 Amp IOD — Spare use only a fuse having the correct amperage rating. Yellow The use of a fuse with a rating other than indicated may result in a dangerous electrical system over- CAUTION! load.
Page 530: Replacement Bulbs
530 MAINTAINING YOUR VEHICLE • The electronic shift transfer case should be placed in • When the vehicle is shipped from the factory, the IOD the 4HI mode and kept in this position to minimize the fuse is in the up or extracted position. If the radio, battery drain.
Page 531: Bulb Replacement
MAINTAINING YOUR VEHICLE 531 BULB REPLACEMENT LIGHT BULBS — Exterior Bulb No. Backup ....... . 921 Dual or Quad Headlamp/Front Park and Turn Center High Mounted Stop Lamp (CHMSL) .
Page 532 532 MAINTAINING YOUR VEHICLE 6. Remove the two headlamp assembly attachment 8. Reach through the access hole of the wheel house screws. splash shield and lift the slide lock upward far enough to disengage it from the lock post on the back of the front lamp unit housing.
Page 533: Fog Lamps
MAINTAINING YOUR VEHICLE 533 10. Disconnect the wiring harness connectors from the Fog Lamps bulb socket. 1. Reach under and behind the front bumper to access 11. Replace bulb(s) as necessary. the back of the front fog lamp housing. 2. Disconnect the fog lamp wiring harness connector CAUTION! from the fog lamp bulb.
Page 534: Rear Tail/Stop, Turn Signal And Backup Lamps
534 MAINTAINING YOUR VEHICLE Rear Tail/Stop, Turn Signal and Backup Lamps 1. Remove the two screws that pass through the bed sheetmetal. 3. Disconnect the wiring harness connectors from the bulb socket. 4. Rotate the bulb socket counterclockwise 1/4 turn to unlock it from the housing.
Page 535: Center High-Mounted Stoplamp (Chmsl) With Cargo Lamp
MAINTAINING YOUR VEHICLE 535 CAUTION! Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. 6. Reverse the procedure to install the bulb and housing. Center High-Mounted Stoplamp (CHMSL) With Cargo Lamp 1.
Page 536 536 MAINTAINING YOUR VEHICLE 2. Separate the connector holding the housing and wir- ing harness to the body. CAUTION! Do not contaminate the bulb glass by touching it 3. Turn the desired bulb socket ⁄ turn and remove the with your fingers or by allowing it to contact other socket and bulb from housing.
Page 537: Cab Top Clearance Lamps - If Equipped
MAINTAINING YOUR VEHICLE 537 • Outside Bulbs: Cargo Lamps • Inside Bulb: Center High-Mounted Stop Lamp 5. Reverse the procedure for installation of bulbs and housing. Cab Top Clearance Lamps — If Equipped 1. Remove the two screws from the top of the lamp.
Page 538 538 MAINTAINING YOUR VEHICLE 2. Rotate the socket ⁄ turn and pull it from the lamp 3. Pull the bulb straight from it’s socket and replace. assembly.
Page 539: Rear Lamp Bar Id Marker (Dual Rear Wheels) - If Equipped
MAINTAINING YOUR VEHICLE 539 Rear Lamp Bar ID Marker (Dual Rear Wheels) — If 2. Turn the socket ⁄ turn counterclockwise to access the Equipped bulb. 1. Loosen the two screws and the housing to gain access 3. Pull the bulb straight out from the socket. to the bulb sockets.
Page 540: Side Marker Lamps (Dual Rear Wheels) - If Equipped
540 MAINTAINING YOUR VEHICLE Side Marker Lamps (Dual Rear Wheels) — If 1. Push rearward on the side marker lamp assembly. Equipped 2. Pull the entire assembly from the fender. 3. Turn the socket ⁄ turn counterclockwise and remove from assembly to access the bulb. 4.
Page 541: Fluids And Capacities
MAINTAINING YOUR VEHICLE 541 FLUIDS AND CAPACITIES U.S. Metric Fuel (Approximate) 1500 Regular Cab Shortbed/Crew Quad Cab Models 26 Gallons 98 Liters 1500 Regular Cab Longbed/Crew Quad Cab Models 32 Gallons 121 Liters (Optional) 2500/3500 Shortbed Models 34 Gallons 129 Liters 2500/3500 Longbed Models 35 Gallons 132 Liters...
Page 542 542 MAINTAINING YOUR VEHICLE U.S. Metric Cooling System 3.7L Engine (MOPAR Antifreeze/Coolant 5 14 Quarts 13 Liters Year/100,000 Mile Formula or equivalent) 4.7L Engine (MOPAR Antifreeze/Coolant 5 14 Quarts 13 Liters Year/100,000 Mile Formula or equivalent) 5.7L Engine — 1500 Models (MOPAR Antifreeze/ 16 Quarts 15 Liters Coolant 5 Year/100,000 Mile Formula or equivalent)
Page 543: Engine
MAINTAINING YOUR VEHICLE 543 FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant MOPAR Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. Engine Oil Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395.
Page 544: Chassis
544 MAINTAINING YOUR VEHICLE Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission MOPAR ATF+4 Automatic Transmission Fluid or equivalent. Transfer Case MOPAR ATF+4 Automatic Transmission Fluid or equivalent. Transfer Case — NVG 246 Only MOPAR NVG 246 Automatic Transmission Fluid or equivalent. Front Axle —...
Page 545 MAINTENANCE SCHEDULES CONTENTS ▫ Required Maintenance Intervals ..548 Emissions Control System Maintenance ..546 Maintenance Schedule ....546...
Page 546 546 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE MAINTENANCE SCHEDULE The Scheduled Maintenance services listed in bold type The oil change indicator system will remind you that it is must be done at the times or mileages specified to ensure time to take your vehicle in for scheduled maintenance. the continued proper functioning of the emissions control On Electronic Vehicle Information Center (EVIC) system.
Page 547 MAINTENANCE SCHEDULES 547 NOTE: At Each Stop for Fuel • The oil change indicator message will not monitor the • Check the engine oil level about five minutes after a time since the last oil change. Change your vehicle’s fully warmed engine is shut off. Checking the oil level oil if it has been six months since your last oil change while the vehicle is on level ground will improve the even if the oil change indicator message is NOT...
Page 548 548 MAINTENANCE SCHEDULES • Check all lights and other electrical items for correct Required Maintenance Intervals operation. NOTE: ** Vehicle’s built with the 4.7L engine are At Each Oil Change equipped with sixteen spark plugs. One set is located on the top of the engine under the coils and the second set is •...
Page 549 MAINTENANCE SCHEDULES 549 6,000 Miles (10,000 km) or 12,000 Miles (20,000 km) or 12 Months Maintenance Service 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. Schedule ❏ Rotate the tires. ❏ Change the engine oil and engine oil ❏...
Page 550: Service Schedule
550 MAINTENANCE SCHEDULES 18,000 Miles (30,000 km) or 24,000 Miles (40,000 km) or 24 Months Maintenance Service 18 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires. ❏ Change the engine oil and engine oil ❏...
Page 551 MAINTENANCE SCHEDULES 551 30,000 Miles (50,000 km) or 36,000 Miles (60,000 km) or 36 Months Maintenance Service 30 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires. ❏ Change the engine oil and engine oil ❏...
Page 552 552 MAINTENANCE SCHEDULES 42,000 Miles (70,000 km) or 48,000 Miles (80,000 km) or 48 Months Maintenance Service 42 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires. ❏ Change the engine oil and engine oil ❏...
Page 553 MAINTENANCE SCHEDULES 553 54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires. ❏ Lube the front drive shaft fitting (2500/3500 (4x4) models only). ❏ Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
Page 554 554 MAINTENANCE SCHEDULES 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires. ❏ Replace the engine air cleaner filter. ❏ Replace the ignition cables (3.7L Engine). ❏...
Page 555 MAINTENANCE SCHEDULES 555 66,000 Miles (110,000 km) or 72,000 Miles (120,000 km) or 72 Months Maintenance Service 66 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires. ❏ Change the engine oil and engine oil ❏...
Page 556 556 MAINTENANCE SCHEDULES 78,000 Miles (130,000 km) or 84,000 Miles (140,000 km) or 84 Months Maintenance Service 78 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires. ❏ Change the engine oil and engine oil ❏...
Page 557 MAINTENANCE SCHEDULES 557 90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires. ❏ Replace the engine air cleaner filter. ❏ Replace the spark plugs (3.7L and 5.7L Engines). ❏...
Page 558 558 MAINTENANCE SCHEDULES 96,000 Miles (160,000 km) or 96 Months Maintenance Service 102,000 Miles (170,000 km) or Schedule 102 Months Maintenance ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires. ❏ Change the engine oil and engine oil ❏...
Page 559 MAINTENANCE SCHEDULES 559 108,000 Miles (180,000 km) or 108 Months Maintenance Service 114,000 Miles (190,000 km) or Schedule 114 Months Maintenance ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires. ❏ Change the engine oil and engine oil ❏...
Page 560 560 MAINTENANCE SCHEDULES 120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires. ❏ Replace the engine air cleaner filter. ❏ Replace the ignition cables (3.7L Engine). ❏...
Page 561 MAINTENANCE SCHEDULES 561 126,000 Miles (210,000 km) or 132,000 Miles (220,000 km) or 132 Months Maintenance Service 126 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires. ❏ Change the engine oil and engine oil ❏...
Page 562 562 MAINTENANCE SCHEDULES 138,000 Miles (230,000 km) or 144,000 Miles (240,000 km) or 144 Months Maintenance Service 138 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires. ❏ Change the engine oil and engine oil ❏...
Page 563 MAINTENANCE SCHEDULES 563 † This maintenance is recommended by the manufacturer 150,000 Miles (250,000 km) or to the owner, but is not required to maintain emissions 150 Months Maintenance Service warranty. Schedule ❏ Change the engine oil and engine oil filter. ❏...
Page 565: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS ▫ Customer Assistance For The Hearing Or Suggestions For Obtaining Service For Your Vehicle......567 Speech Impaired (TDD/TTY) .
Page 566 566 IF YOU NEED CONSUMER ASSISTANCE ▫ Traction Grades ..... 573 Publication Order Forms ....571 ▫...
Page 567: Suggestions For Obtaining Service For Your Vehicle
IF YOU NEED CONSUMER ASSISTANCE 567 SUGGESTIONS FOR OBTAINING SERVICE FOR the service advisor and list the items in order of priority. YOUR VEHICLE At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the...
Page 568: Chrysler Group Llc Customer Center
568 IF YOU NEED CONSUMER ASSISTANCE • Vehicle delivery date and mileage This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- Chrysler Group LLC Customer Center solved with this process. P.O.
Page 569: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
IF YOU NEED CONSUMER ASSISTANCE 569 Customer Assistance For The Hearing Or Speech the manufacturer’s service contracts. If you purchased a Impaired (TDD/TTY) manufacturer’s service contract, you will receive Plan To assist customers who have hearing difficulties, the Provisions and an Owner Identification Card in the mail manufacturer has installed special TDD (Telecommuni- within three weeks of the vehicle delivery date.
Page 570: Warranty Information (U.s. Vehicles Only)
570 IF YOU NEED CONSUMER ASSISTANCE We appreciate that you have made a major investment WARRANTY INFORMATION (U.S. Vehicles Only) when you purchased the vehicle. An authorized dealer See the Warranty Information Booklet, located on the has also made a major investment in facilities, tools, and DVD, for the terms and provisions of Chrysler Group training to assure that you are absolutely delighted with LLC warranties applicable to this vehicle.
Page 571: In Canada
IF YOU NEED CONSUMER ASSISTANCE 571 If NHTSA receives similar complaints, it may open an Transport Canada, Motor Vehicle Defect Investigations investigation, and if it finds that a safety defect exists in and Recalls, 2780 Sheffield Road, Ottawa, Ontario K1B a group of vehicles, it may order a recall and remedy 3V9.
Page 572 572 IF YOU NEED CONSUMER ASSISTANCE • Owner’s Manuals vehicle, system, and/or components is written in straightforward language with illustrations, diagrams, These Owner’s Manuals have been prepared with the and charts. assistance of service and engineering specialists to • Diagnostic Procedure Manuals acquaint you with specific Chrysler Group LLC ve- hicles.
Page 573: Traction Grades
IF YOU NEED CONSUMER ASSISTANCE 573 DEPARTMENT OF TRANSPORTATION UNIFORM significantly from the norm due to variations in driving TIRE QUALITY GRADES habits, service practices, and differences in road charac- The following tire grading categories were established by teristics and climate. the National Highway Traffic Safety Administration.
Page 574: Department Of Transportation Uniform Tire ▫ Temperature Grades
574 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades WARNING! The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat The temperature grade for this tire is established for and its ability to dissipate heat, when tested under a tire that is properly inflated and not overloaded.
Page 575 INDEX...
Page 576 576 INDEX Adding Fuel ......428 Alarm System (Security Alarm) ....18 Adjustable Pedals .
Page 577 INDEX 577 Fluid Type ......516,544 Brake Fluid ......513,544 Gear Ranges .
Page 578 578 INDEX Power Steering ......371 Cleaning Radiator (Coolant Pressure) ....510 Wheels .
Page 579 INDEX 579 Coolant Level ..... . 508,511 Dipsticks Disposal of Used Coolant ....511 Automatic Transmission .
Page 580 580 INDEX Electronic Brake Control System ... . . 377 Engine ......490,491,492 Anti-Lock Brake System .
Page 581 INDEX 581 Exterior Lights ......82 Fluid Leaks ......82 Fluid Level Checks Filters Automatic Transmission .
Page 582 582 INDEX Requirements ..... . 419,541 Tachometer ......202 Saver Mode .
Page 583 INDEX 583 Cleaning ......523 Key ....... 12,14 High Beam .
Page 584 584 INDEX Jack Location ......460 Life of Tires ......403 Jump Starting .
Page 585 INDEX 585 Four-Wheel Drive Indicator ....314 Tire Pressure Monitoring (TPMS) ... 213 Hazard Warning Flasher ....460 Traction Control .
Page 586 586 INDEX Maintenance Schedule ....546 Monitor, Tire Pressure System ....410 Malfunction Indicator Light (Check Engine) .
Page 587 INDEX 587 Dipstick ......497 Owner’s Manual (Operator Manual) ..4,571 Disposal .
Page 588 588 INDEX Sliding Rear Window ....172 Rear Window, Sliding ..... 172 Steering .
Page 589 INDEX 589 Restraint, Head ......98 Child Restraint ..... . . 64,78 Restraints, Child .
Page 590 590 INDEX Sentry Key Replacement ....16 Snow Chains (Tire Chains) ....405 Service Assistance .
Page 591 INDEX 591 Storage, Vehicle ..... . 284,529 Tires ......82,398,573 Storing Your Vehicle .
Page 592 592 INDEX Spinning ......402 Wiring ......446 Tread Wear Indicators .
Page 593 INDEX 593 Trip Odometer ......206 Warning Lights Turn Signals ....121,202,531,534 (Instrument Cluster Description) .
Page 594 594 INDEX Windows ......34 Windshield Wiper Blades ....504 Power .

This manual is also suitable for:

2010 ram

Dodge Ram 2010 Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

Quick Links

INTRODUCTION

Chapters

Related Manuals for Dodge Ram 2010

Summary of Contents for Dodge Ram 2010