Page 1 Ram Truck 2 0 1 0 OWNE R ’ S MANUAL...
Page 2: Introduction
TABLE OF CONTENTS SECTION PAGE ............3 INTRODUCTION .
Page 4: Table Of Contents
INTRODUCTION CONTENTS Introduction ......4 Van Conversions/Campers ....6 How To Use This Manual .
Page 5: Introduction
4 INTRODUCTION INTRODUCTION When it comes to service, remember that your authorized Congratulations on selecting your new Chrysler Group dealer knows your vehicle best, has factory-trained tech- LLC vehicle. Be assured that it represents precision nicians and genuine MOPAR parts, and cares about workmanship, distinctive styling, and high quality - all your satisfaction.
Page 6 INTRODUCTION 5...
Page 7: Van Conversions/Campers
6 INTRODUCTION WARNINGS AND CAUTIONS Operating instructions for the special equipment in- This Owner’s Manual contains WARNINGS against op- stalled by the conversion/camper manufacturer should erating procedures that could result in an accident or also be supplied with your vehicle. If these instructions bodily injury.
Page 8: Vehicle Identification Number
INTRODUCTION 7 NOTE: It is illegal to remove or alter the VIN. VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is found on the VEHICLE MODIFICATIONS/ALTERATIONS left front corner of the instrument panel, visible through the windshield. This number also appears on the Auto- WARNING! mobile Information Disclosure Label affixed to a window on your vehicle, the vehicle registration and title.
Page 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 General Information ....17 Wireless Ignition Node (WIN) —...
Page 11 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Open Window Feature — Power Windows – If Equipped ... . 34 If Equipped ......23 Wind Buffeting .
Page 12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 Driver And Right Front Passenger Engine Break-In Recommendations ..76 Supplemental Restraint System (SRS) – Safety Tips ......77 Airbag .
Page 13: Things To Know Before Starting Your Vehicle 9
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS authorized dealer. Ask your authorized dealer for these numbers and keep them in a safe place. You can insert the Key Fob with Remote Keyless Entry (RKE) — If double-sided standard blade key into the ignition switch Equipped with either side up.
Page 14: Key Fob
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Key Fob The Key Fob operates the ignition switch. It also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the RKE transmitter go dead.
Page 15: Removing Key Fob From Ignition
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To remove the emergency key, slide the mechanical latch Removing Key Fob From Ignition at the top of the Key Fob sideways with your thumb and Place the shift lever in PARK. Turn the Key Fob to the then pull the key out with your other hand.
Page 16: Key-In-Ignition Reminder
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 (EVIC)/Personal Settings (Customer-Programmable Key-In-Ignition Reminder Features)” in “Understanding Your Instrument Panel” Opening the driver’s door when the Key Fob is in the for further information. ignition and the ignition switch position is OFF or ACC, sounds a signal to remind you to remove the Key Fob.
Page 17: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The system uses Key Fob with factory-mated Remote If the Vehicle Security Light turns on during normal Keyless Entry (RKE) transmitter and Wireless Ignition vehicle operation (vehicle running for longer than 10 sec- Node (WIN) to prevent unauthorized vehicle operation.
Page 18: Customer Key Programming
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 • If a programmed Key Fob is lost, see your authorized CAUTION! dealer to have all remaining Key Fobs erased from the system’s memory. This will prevent the lost Key Fobs Always remove the Sentry Keys from the vehicle from starting your vehicle.
Page 19: Vehicle Security Alarm - If Equipped
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE VEHICLE SECURITY ALARM — IF EQUIPPED To Set the Alarm The Vehicle Security Alarm monitors the vehicle doors The Vehicle Security Alarm will set when you use the and ignition for unauthorized operation. When the Ve- power door locks, or use the Remote Keyless Entry (RKE) hicle Security Alarm is activated, the system provides transmitter to lock the doors.
Page 20: Illuminated Entry - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 The Vehicle Security Alarm will also disarm if the vehicle ILLUMINATED ENTRY — IF EQUIPPED is started with a programmed Sentry Key . If an unpro- The courtesy lights will turn on when you use the grammed Sentry Key is used to start a vehicle, the Remote Keyless Entry (RKE) transmitter or open the engine will run for two seconds and then the alarm will...
Page 21: Remote Keyless Entry (Rke) - If Equipped
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE KEYLESS ENTRY (RKE) — IF EQUIPPED The RKE system allows you to lock or unlock the doors and activate the Panic Alarm from distances up to approximately 66 ft (20 m) using a hand-held radio transmitter with integrated key.
Page 22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 2. Release both buttons at the same time. Remote Key Unlock, Driver Door/All Doors First This feature lets you program the system to unlock either 3. Test the feature while outside of the vehicle by press- the driver’s door or all doors on the first press of the ing the LOCK/UNLOCK buttons on the RKE transmitter UNLOCK button on the RKE transmitter.
Page 23: To Lock The Doors
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Flash Lamps with Remote Key Lock 3. Test the feature while outside of the vehicle by press- This feature will cause the turn signal lights to flash when ing the LOCK/UNLOCK buttons on the RKE transmitter the doors are locked or unlocked with the RKE transmit- with the ignition switch in the OFF position and the key ter.
Page 24: Things To Know Before Starting Your Vehicle 23
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 3. Test the feature while outside of the vehicle by press- Sound Horn with Remote Key Lock This feature will cause the horn to chirp when the doors ing the LOCK button on the RKE transmitter with the are locked with the RKE transmitter.
Page 25: Using The Panic Alarm
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • You may need to be less than 35 ft (11 m) from the Using the Panic Alarm To turn the Panic Alarm feature ON or OFF, press and vehicle when using the RKE transmitter to turn off the hold the PANIC button on the RKE transmitter for at Panic Alarm due to the radio frequency noises emitted least one second and release.
Page 26: General Information
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 1. With the RKE transmitter buttons facing down, use a Changes or modifications not expressly ap- NOTE: flat blade to pry the two halves of the RKE transmitter proved by the party responsible for compliance could apart.
Page 27: How To Use Remote Start
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Use Remote Start WARNING! All of the following conditions must be met before the • Do not start or run an engine in a closed garage or engine will remote start: confined area.
Page 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 • Remote Start Aborted - Hood Ajar • For security, power window and power sunroof op- eration (if equipped) are disabled when the vehicle is • Remote Start Aborted - Fuel Low in the Remote Start mode.
Page 29: Door Locks
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Exit Remote Start Mode and Drive the Vehicle turn on in cold weather. In warm weather, the driver Before the end of the 15-minute cycle, press and release vented seat feature will automatically turn on when the the UNLOCK button on the RKE transmitter to unlock remote start is activated.
Page 30: Power Door Locks - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 Front doors may be opened with the inside door handle Power Door Locks — If Equipped without lifting the lock plunger. A power door LOCK switch is on each front door trim panel.
Page 31 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with the EVIC, perform the power locks will not operate. This prevents you from accidentally locking your Key Fob in the vehicle. Remov- following procedure: ing the Key Fob or closing the door will allow the locks to 1.
Page 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 • For vehicles not equipped with the EVIC, perform the 8. If a chime is not heard, program mode was canceled before the feature could be disabled. If necessary, repeat following procedure: the above procedure.
Page 33: Child Protection Door Lock
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 7. Repeat the above steps to alternate the availability of this feature. 8. If a chime is not heard, the program mode was canceled before the feature could be changed. If neces- sary, repeat the above procedure.
Page 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 a door is engaged, that door can only be opened by using WARNING! the outside door handle even if the inside door lock is in the unlocked position. Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged.
Page 35: Windows
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOWS The control on the left front door panel has UP-DOWN switches that give you fingertip control of all power Power Windows – If Equipped windows. There is a single opening and closing switch on the front passenger door for passenger window control and on the rear doors of Quad Cab , Mega Cab and Crew Cab models.
Page 36: Auto Down
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 To open the window part way, press to the first detent WARNING! and release it when you want the window to stop. Never leave children alone in a vehicle. Leaving Auto-Up Feature with Anti-Pinch Protection unattended children in a vehicle is dangerous for a (4-Door Models Driver’s and Front Passenger Door number of reasons.
Page 37 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE rough road conditions may trigger the auto reverse press the window LOCK button into the latched or down function unexpectedly during auto closure. If this position. To enable the window controls, press the win- happens, pull the switch lightly to the first detent and dow LOCK button again and return the switch to the hold to close the window manually.
Page 38: Wind Buffeting
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 • Supplemental Side Airbag Inflatable Curtains (SABIC) Wind Buffeting Wind buffeting can be described as the perception of — if equipped pressure on the ears or a helicopter-type sound in the • An energy-absorbing steering column and steering ears.
Page 39: Lap/Shoulder Belts
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Please pay close attention to the information in this Research has shown that seat belts save lives, and they section. It tells you how to use your restraint system can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown properly, to keep you and your passengers as safe as possible.
Page 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 WARNING! WARNING! (Continued) • Wearing a seat belt incorrectly is dangerous. Seat • It is extremely dangerous to ride in a cargo area, belts are designed to go around the large bones of inside or outside of a vehicle.
Page 41 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt.
Page 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 3. When the belt is long enough to fit, insert the latch WARNING! plate into the buckle until you hear a “click.” • A belt buckled into the wrong buckle will not protect you properly.
Page 43 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • A shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt.
Page 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 WARNING! WARNING! • A lap belt worn too high can increase the risk of A frayed or torn belt could rip apart in a collision and internal injury in a collision. The belt forces won’t be leave you with no protection.
Page 45 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE belt tongue is pressed into the buckle. Allow the retractor 2. To reattach the seat belt to the front center seat, pull to take up the surplus webbing, and the buckles will the black buckle latch plate forward from the cab back hang vertically from the cab back exit bezel, thus freeing panel and insert it into the black keyed buckle until there...
Page 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 Inserting Latch Plate In Use Position...
Page 47: Adjustable Upper Shoulder Belt Anchorage
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE away from your neck. Press the button located on the WARNING! upper belt guide, and then move it up or down to the • If the black latch and black buckle are not prop- position that fits you best.
Page 48: Center Lap Belts
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 you will prefer a higher position. When you release the WARNING! (Continued) anchorage, try to move it up or down to make sure that • A belt that is too loose or too high will apply crash it is locked in position.
Page 49: Seat Belt Pretensioners - If Equipped
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Use The Automatic Locking Mode by assuring that the belt is tight about the occupant early in a collision. Pretensioners work for all size occupants, 1. Buckle the combination lap/shoulder belt. including those in child restraints.
Page 50: Seat Belts And Pregnant Women
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 Once the warning is triggered, the BeltAlert will con- 3. Within 60 seconds of starting the vehicle, unbuckle tinue to chime and flash the Seat Belt Reminder Light for and then re-buckle the driver’s seat belt at least three 96 seconds or until the driver’s seat belt is buckled.
Page 51: Seat Belt Extender
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Pregnant women should wear the lap part of the belt WARNING! across the thighs and as snug against the hips as possible. Keep the belt low so that it does not come across the Using a seat belt extender when not needed can abdomen.
Page 52: Airbag System Components
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 The Advanced Front Airbags have a multistage inflator design. This allows the airbag to have different rates of inflation based on the severity and type of collision. This vehicle may also be equipped with Supplemental Side Airbag Inflatable Curtains (SABIC) to protect the driver, front, and rear passengers sitting next to a win- dow.
Page 53: Advanced Front Airbag Features
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Front Passenger Airbag The first stage inflator is triggered immediately during an impact that requires airbag deployment. The timing of • Front and Side Impact Sensors — if equipped the second stage determines whether the output force is •...
Page 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 chambers placed adjacent to the head of each outboard WARNING! (Continued) occupant that reduce the potential for side-impact head • Do not put anything on or around the airbag injuries. The curtains deploy downward, covering both covers or attempt to open them manually.
Page 55 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The system includes sensors adjacent to both front and Knee Impact Bolsters rear seat occupants that are calibrated to deploy the The Knee Impact Bolsters help protect the knees of the SABIC airbags during impacts that require airbag occu- driver and the front passenger, and position everyone for pant protection.
Page 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 You should read the instructions provided with your WARNING! child restraint to make sure that you are using it properly. Infants in rear-facing child restraints should NEVER All occupants should ALWAYS wear their lap and shoul- ride in the front seat of a vehicle with a passenger der belts properly.
Page 57: Airbag Deployment Sensors And Controls
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Deployment Sensors and Controls WARNING! Occupant Restraint Controller (ORC) • Relying on the airbags alone could lead to more The ORC is part of a Federally regulated safety system severe injuries in a collision. The airbags work required for this vehicle.
Page 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 The Advanced Front Airbags will not deploy in all frontal The ORC monitors the readiness of the electronic parts of collisions, including some that may produce substantial the system whenever the ignition switch is in the START vehicle damage —...
Page 59 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE It also includes diagnostics that will illuminate the instru- the Advanced Front Airbags. Different airbag inflation ment cluster Airbag Warning Light if a malfunction is rates are possible, based on the collision type and sever- noted.
Page 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 deploy the SABIC airbags, depending on severity and Front and Side Impact Sensors — If Equipped type of collision. In these events, the ORC will deploy the In front and side impacts, impact sensors aid the ORC in SABIC only on the impact side of the vehicle.
Page 61 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Turn on the interior lights, which remain on as long as floor. They are not caused by contact with chemicals. the battery has power or until the ignition key is They are not permanent and normally heal quickly. removed.
Page 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Maintaining Your Airbag System WARNING! WARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, • Modifications to any part of the airbag system seat belt pretensioners, and the front passenger seat could cause it to fail when you need it.
Page 63 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Warning Light WARNING! (Continued) You will want to have the airbags ready to • Do not attempt to modify any part of your ad- inflate for your protection in a collision. While vanced airbag system.
Page 64: Event Data Recorder (Edr)
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 located on the inside of the fuse block cover for the 2. Under certain circumstances, EDR data may not be proper airbag fuses. See your authorized dealer if the recorded (e.g., loss of battery power). fuse is good.
Page 65: Child Restraint
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE accessing the electronic data stored, unless ordered to 3. Requested by police under a legal warrant. download data by a court with legal jurisdiction (i.e., 4. Otherwise required by law. pursuant to a warrant). A copy of the data will be provided to the custodial entity upon request.
Page 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 United States and all Canadian provinces require that Infants and Small Children small children ride in proper restraint systems. This is the There are different sizes and types of restraints for law, and you can be prosecuted for ignoring it. children from newborn size to the child almost large enough for an adult safety belt.
Page 67 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE infant carriers do, so they can be used rearward-facing cushion while the child’s back is against the seat back, by children who weigh more than 20 lbs (9 kg) but are they should use a belt-positioning booster seat. The less than one year old.
Page 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 from the buckle and twist the short buckle-end belt Here are some tips for getting the most out of your child restraint: several times to shorten it. Insert the latch plate into the buckle with the release button facing out.
Page 69 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
Page 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 some time. In fact, many child restraint manufacturers of reach of children. It is recommended that before will provide add-on tether strap kits for some of their installing the child restraint, buckle the seat belt so the older products.
Page 71 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing the Child Restraint System rearward-facing infant restraints will also be equipped with a tether strap, a hook and means for adjusting the WARNING! tension in the strap. In general, you will first loosen the adjusters on the lower Do not install child restraint systems equipped with straps and tether straps so that you can more easily attach LATCH attachments in the center position of a Quad...
Page 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 the lap portion around the child restraint. Any seat belt Installing Child Restraints Using the Vehicle Seat Belt system will loosen with time, so check the belt occasion- The seat belts in the passenger seating positions are ally, and pull it tight if necessary.
Page 73 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Install the child restraint and remove the slack in the WARNING! tether strap according to the manufacturer’s instructions. An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle.
Page 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Multiple Child Restraint Installation Sequence (Quad Cab /Crew Cab/Mega Cab - Rear Seats) Quad Cab /Mega Cab 1. Obtain tether straps by raising the head restraints and reaching between the rear glass and rear seat. The tether strap may be retained with an elastic band.
Page 75 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Route each tether strap to the anchor behind the center seat, and attach the hooks to the metal ring. 5. Place a child restraint on the center rear seat and adjust the tether strap so that it will reach under the head restraint to the tether anchor directly behind the seat and to the anchor directly behind the right seat.
Page 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 2. Place a child restraint on each outboard rear seat and Crew Cab adjust the tether strap so that it will reach under the head 1. The tether straps loops are located between the rear glass restraint, through the outboard tether strap loop, then and the rear seat.
Page 77: Engine Break-In Recommendations
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. Install each child restraint and remove the slack in the Transporting Pets tether strap according to the child restraint manufactur- Airbags deploying in the front seat could harm your pet. er’s instructions. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in Children Too Large for Booster Seats...
Page 78: Safety Tips
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 The engine oil installed in the engine at the factory is a SAFETY TIPS high-quality energy conserving type lubricant. Oil Transporting Passengers changes should be consistent with anticipated climate NEVER TRANSPORT PASSENGERS IN THE CARGO conditions under which vehicle operations will occur.
Page 79: Exhaust Gas
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exhaust Gas If you are required to drive with the trunk/liftgate open, make sure that all windows are closed and the climate WARNING! control BLOWER switch is set at high speed. DO NOT use the recirculation mode.
Page 80: Safety Checks You Should Make Inside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 Safety Checks You Should Make Inside the Defroster Vehicle Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to Seat Belts feel the air directed against the windshield. See your Inspect the belt system periodically, checking for cuts, authorized dealer for service if your defroster is frays, and loose parts.
Page 81 80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Door Latches Check for positive closing, latching, and locking. Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, power steering fluid, or brake fluid leaks are suspected, the cause should be located and corrected immediately.
Page 82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors ......87 Illuminated Vanity Mirror — If Equipped ..92 Inside Day/Night Mirror .
Page 83 82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjustable Head Restraints ....97 Driver Easy Exit And Easy Entry Control . . . 112 Eight-Way Power Seats — If Equipped ..100 To Open And Close The Hood .
Page 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 Daytime Running Lights (DRL) To Set a Desired Speed ....129 (Canada Only And Fleet Vehicles) ..121 Deactivating Electronic Speed Control .
Page 85 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Parkview Rear Back Up Camera — Security ......150 If Equipped .
Page 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 Electrical Power Outlets ....154 Center Storage Compartment — If Equipped ......166 Cigar Lighter And Ash Receiver —...
Page 87 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fold Flat Load Floor — If Equipped ..173 Slide-In Campers ..... . 189 Rambox —...
Page 88: Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 MIRRORS Inside Day/Night Mirror Headlight glare can be reduced by moving the small control lever under the mirror to the night position (lever flipped toward the rear of vehicle). Adjusting Rearview Mirror The mirror should be adjusted with the lever set in the day position (lever flipped toward the windshield).
Page 89: Automatic Dimming Mirror
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped CAUTION! This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or To avoid damage to the mirror during cleaning, never off by pressing the power button at the base of the mirror.
Page 90: Outside Mirrors Folding Feature
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 WARNING! Vehicles and other objects seen in a passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side convex mirror could cause you to collide with another vehicle or other object.
Page 91: Power Mirrors - If Equipped
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Mirrors — If Equipped The power mirror controls consist of mirror select but- The controls for the power mirrors are located on the tons and a four-way mirror control switch. driver’s door trim panel. Power Mirror Controls Power Mirror Controls 1 —...
Page 92: Heated Mirrors - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 To adjust a mirror, press the mirror select button for the Heated Mirrors — If Equipped mirror that you want to adjust. Using the mirror control These mirrors are heated to melt frost or ice. This switch, press on any of the four arrows for the direction feature is activated whenever you turn on the rear that you want the mirror to move.
Page 93: Illuminated Vanity Mirror - If Equipped
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Illuminated Vanity Mirror — If Equipped “Slide-On-Rod” Features of Sun Visor — If Equipped Illuminated vanity mirrors are located on each sun visor. The sun visor “Slide-On-Rod” feature allows for additional To use the mirror, rotate the sun visor down and swing flexibility in positioning the visor to block out the sun.
Page 94: Trailer Towing Mirrors - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 NOTE: Fold the trailer towing mirrors rearward prior to Trailer Towing Mirrors — If Equipped These mirrors are designed with an adjustable mirror entering an automated car wash. head to provide a greater vision range when towing A small blindspot mirror is located next to main mirror extra-wide loads.
Page 95: Uconnect™ Phone - If Equipped
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Uconnect™ Phone — IF EQUIPPED WARNING! Refer to “Uconnect™ Phone” in the Uconnect™ User • It is extremely dangerous to ride in a cargo area, Manual located on the DVD for further details. inside or outside of a vehicle.
Page 96: Manual Seat Adjuster - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 Manual Seat Adjuster — If Equipped Both front seats are independently adjustable forward or rearward and are equipped with a seatback recliner. The manual forward or rearward seat adjustment handle is found under the seat cushion at the front edge of each seat.
Page 97: Manual Reclining Seats - If Equipped
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.
Page 98: Adjustable Head Restraints
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 WARNING! WARNING! (Continued) • You can be seriously, even fatally, injured riding in • Actuating the recliner handle will allow the seat- a seat with the seatback reclined. Do not ride with back to swing (dump) forward on manual recliner the seatback reclined so that the shoulder belt is seats.
Page 99 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To raise the head restraint, pull upward on the head To remove the head restraint, pull upward on the head restraint. To lower the head restraint, press the large restraint to it’s highest position, push in both buttons at button, located on the base of the head restraint, and the base of each head restraint rod, and simultaneously push downward on the head restraint.
Page 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 until the head restraint reaches the first lock position, lower the head restraint, press the large button, located push the large button in and push down and adjust head on the base of the head restraint, and push downward on restraint to desired position.
Page 101: Eight-Way Power Seats - If Equipped
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Eight-Way Power Seats — If Equipped The power seat controls are on the outboard side of the front seat cushions. The power seat switch can be moved forward and backward as well as up and down to control the position of the seat.
Page 102: Power Lumbar - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 Power Lumbar — If Equipped WARNING! The lumbar controls are located on the outboard side of the seat cushion. The lumbar support can be increased by Adjusting a seat while the vehicle is moving is pressing the front of the switch and decreased by press- dangerous.
Page 103: Heated Seats - If Equipped
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the switch once to select High- WARNING! level heating. Press the switch a sec- ond time to select Low-level heating. Adjusting a seat while the vehicle is moving is Press the switch a third time to shut dangerous.
Page 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 NOTE: The drivers heated seat can be programmed to WARNING! (Continued) come on during a remote start. Refer to “Remote Starting • Do not place anything on the seat that insulates System — If Equipped” in “Things to Know Before against heat, such as a blanket or cushion.
Page 105: Ventilated Seats - If Equipped
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Ventilated Seats — If Equipped the switch will be illuminated. When Low speed is Located in the seat cushion and seatback are small fans selected one light will be illuminated. that draw the air from around the occupant and exhaust NOTE: it underneath the seat and into the passenger compart- •...
Page 106: Mega Cab Rear Seat Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Mega Cab Rear Seat Features WARNING! Reclining Rear Seats — If Equipped Do not ride with the seatback reclined so that the The recliner handle is located on the outside of the seat shoulder belt is no longer resting against your chest.
Page 107 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Rear Seat (Table Mode) — If Equipped 2. Fold the seatback forward. Both the left and right rear seatbacks can be folded down and used as a table. To fold down either rear seatback: 1.
Page 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 To fold either rear seat flat: WARNING! 1. Lift the handle, located on the outboard side of either • It is extremely dangerous to ride in a cargo area, of the rear seats. inside or outside of a vehicle.
Page 109: Driver Memory Seat - If Equipped
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Fold the seatback down and push the seat forward. 3. Lift the seatback, to return the seat to the upright position. Be sure the seat is locked in place. WARNING! Be certain that the seatback is securely locked into position.
Page 110: Setting Memory Positions And Linking Rke
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Keyless Entry (RKE) transmitters can also be pro- grammed to recall the same positions when the UN- LOCK button is pressed. NOTE: The power lumbar option is not programmable with driver memory seats. Your vehicle was delivered with two RKE transmitters.
Page 111: Memory Position Recall
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Adjust the driver’s seat, recliner, and both sideview performed within 10 seconds if you desire to also use a mirrors to the desired positions. RKE transmitter to recall memory positions. NOTE: Not all motors may be moved at one time. Refer 8.
Page 112: To Disable A Rke Transmitter Linked To Memory
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 • Not all motors may be moved at one time. Refer to the when not in the ignition switch. When a recall is can- “Seats/Eight-Way Power Seat” in this section for fur- celled, the driver’s seat and the pedals stop moving. A ther information.
Page 113: Self-Limiting Control
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The capability to link RKE transmitters to self-limiting control may be reset by reaching the new memory is enabled when delivered from the factory. The stored position, then press and release MEMORY button capability to link RKE transmitters to memory can be 1 or 2.
Page 114: To Open And Close The Hood
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 NOTE: The Easy Entry/Easy Exit feature can be en- abled or disabled through the programmable features in the Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)/ Customer-Programmable Features” in “Understanding Your Instrument Panel”...
Page 115 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Reach into the opening beneath the center of the hood CAUTION! and push the safety latch lever from right to left to release it, before raising the hood. To prevent possible damage, do not slam the hood to close it.
Page 116: Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Your vehicle is equipped with plastic headlight and fog LIGHTS The headlight switch is located on the left side of the light (if equipped) lenses that are lighter and less suscep- instrument panel, next to the steering wheel. The head- tible to stone breakage than glass lights.
Page 117: Headlights
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights To turn on the headlights, rotate the headlight switch clockwise. When the headlight switch is on the parking lights, taillights, license plate light and instrument panel lights are also turned on. To turn off the headlights, rotate the headlight switch back to the O (Off) position.
Page 118: Smartbeam™ - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 NOTE: The engine must be running before the head- 2. Turn the headlight switch to the AUTO headlight lights will turn on in the Automatic Mode. position. 3. Push the multifunction lever away from you (toward SmartBeam™...
Page 119: Headlight Delay
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlight Delay parking light symbol. To turn off the parking lights, To aid in your exit, your vehicle is equipped with a rotate the headlight switch back to the O (Off) position. headlight delay that will leave the headlights on for Fog Lights —...
Page 120: Interior Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 The fog lights will operate only when the parking lights The brightness of the instrument panel lighting can be regulated by rotating the dimmer control right (brighter) are on or when the vehicle headlights are on low beam. or left (dimmer).
Page 121: Cargo Light
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Light Lights-on Reminder The cargo lights are turned on by pressing on the cargo If the headlights, parking lights, or cargo lights are left on button. after the ignition is turned OFF, a chime will sound when the driver’s door is opened.
Page 122: Daytime Running Lights (Drl) (Canada Only And Fleet Vehicles)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Daytime Running Lights (DRL) (Canada Only and Turn Signals Fleet Vehicles) Move the multifunction lever up or down and the arrows The headlights on your vehicle will illuminate when the on each side of the instrument cluster flash to show engine is started and the transmission is in any gear proper operation of the front and rear turn signal lights.
Page 123 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If either light remains on and does not flash, or High/Low Beam Switch there is a very fast flash rate, check for a defective outside Push the multifunction lever toward the instrument light bulb.
Page 124: Windshield Wipers And Washers
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 WINDSHIELD WIPERS AND WASHERS Intermittent Wiper System The intermittent feature of this system was designed for Windshield Wipers use when weather conditions make a single wiping cycle, The wipers and washers are operated by a switch in the with a variable pause between cycles, desirable.
Page 125: Windshield Washers
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Washers WARNING! To use the windshield washer, push the washer knob, located on the end of the multifunction lever, inward to Sudden loss of visibility through the windshield the second detent. Washer fluid will be sprayed until the could lead to an accident.
Page 126: Heated Steering Wheel - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Pull the lever toward the steering wheel to unlock the WARNING! steering column. With one hand firmly on the steering wheel, move the steering column up or down, as desired. Do not adjust the steering column while driving. Release the lever to lock the steering column firmly in Adjusting the steering column while driving or driv- place.
Page 127 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The heated steering wheel switch is located on the switch WARNING! bank below the climate controls. • Persons who are unable to feel pain to the skin Press the switch to turn on the heated because of advanced age, chronic illness, diabetes, steering wheel.
Page 128: Driver Adjustable Pedals - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 DRIVER ADJUSTABLE PEDALS — IF EQUIPPED The power adjustable accelerator and brake pedals allow the driver to establish a comfortable position relative to the steering wheel and pedals. Adjustment 1. Position the driver’s seat so that you are at least 10 in (25.4 cm) away from the airbag, located in the center of the steering wheel.
Page 129: Electronic Speed Control - If Equipped
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL — IF EQUIPPED CAUTION! When engaged, Electronic Speed Control takes over the accelerator operation at speeds greater than 25 mph Do not place any article under the adjustable pedals (40 km/h). The Electronic Speed Control lever is located or impede its ability to move as it may cause damage on the right side of the steering wheel.
Page 130: To Activate
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 NOTE: In order to ensure proper operation, the Elec- WARNING! tronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated Leaving the Electronic Speed Control system on simultaneously.
Page 131: Deactivating Electronic Speed Control
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Deactivating Electronic Speed Control RESUME ACCEL position, the set speed will continue to A soft tap on the brake pedal or pulling the Electronic increase until the lever is released, then the new set speed Speed Control lever (CANCEL) toward you will deacti- will be established.
Page 132: To Accelerate For Passing
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 To Accelerate for Passing WARNING! Press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Electronic Speed Control can be dangerous where the system cannot maintain a constant speed.
Page 133: Parksense Rear Park Assist - If Equipped
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE PARKSENSE REAR PARK ASSIST — IF ParkSense Sensors EQUIPPED The four ParkSense sensors, located in the rear bumper, The ParkSense Rear Park Assist system provides visual monitor the area behind the vehicle that is within the and audible indications of the distance between the rear sensors’...
Page 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 The ParkSense Warning Display is located in the instru- When the vehicle is in REVERSE, the warning display ment cluster’s EVIC display. It provides both visual and will turn ON indicating the system status. audible warnings to indicate the distance between the rear bumper and the detected obstacle.
Page 135 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Park Assist Disabled Slow Tone ParkSense will indicate a detected obstacle by showing three solid arcs and will produce a ⁄ second tone. As the vehicle moves closer to the object the EVIC display will show fewer arcs and the sound tone will change from slow, to fast, to continuous.
Page 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 Fast Tone Continuous Tone The vehicle is close to the obstacle when the EVIC display shows one flashing arc and sounds a continuous tone.
Page 137 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING DISPLAY DISTANCES DISPLAY MESSAGE OBSTACLE DISTANCE FROM: ARC’s AUDIBLE SIG- REAR CORNERS REAR CENTER Park Assist ON None None Warning Object Detected 78.7 in (200 cm) 3 Solid Yes, 1/2 second Warning Object Detected 39.3 in (100 cm) 3 Flashing Slow Tone...
Page 138: Enable/Disable Parksense
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 Enable/Disable ParkSense ParkSense can be enabled and disabled with a switch located in the switch bank of the instrument panel or through the Customer-Programmable Features section of the EVIC. The available choices are: OFF, Sound Only, or Sound and Display.
Page 139: Service Parksense
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE and the system is disabled, the EVIC will display the If “CLEAN PARK ASSIST SENSORS” appears in the “PARK ASSIST DISABLED” message for as long as the Electronic Vehicle Information Center (EVIC) after mak- vehicle is in REVERSE.
Page 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 • When you turn ParkSense off, the instrument cluster Information Center (EVIC) after making sure the rear will display “PARK ASSIST DISABLED.” Further- bumper is clean and free of snow, ice, mud, or other more, once you turn ParkSense off, it remains off debris, see your authorized dealer.
Page 141 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! • The ParkSense Rear Park Assist system is only a • Drivers must be careful when backing up even parking aid and it is unable to recognize every when using the ParkSense Rear Park Assist sys- obstacle, including small obstacles.
Page 142: Understanding The Features Of Your Vehicle 141
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 PARKVIEW REAR BACK UP CAMERA — IF WARNING! (Continued) EQUIPPED • Before using the ParkSense Rear Park Assist Your vehicle may be equipped with the ParkView Rear system, it is strongly recommended that the ball Back Up Camera that allows you to see an on-screen mount and hitch ball assembly is disconnected image of the rear of your vehicle whenever the shift lever...
Page 143: Turning Parkview On Or Off - With Navigation/Multimedia Radio
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turning ParkView On or Off — With CAUTION! Navigation/Multimedia Radio • To avoid vehicle damage, ParkView should only 1. Press the “menu” hard key. be used as a parking aid. The ParkView camera is 2.
Page 144: Turning Parkview On Or Off - Without Navigation/Multimedia Radio
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 • Courtesy/Reading Lights Turning ParkView On or Off — Without Navigation/Multimedia Radio • Power Sunroof Switch — If Equipped 1. Press the “menu” hard key. • Power Sliding Rear Window Switch — If Equipped 2.
Page 145: Courtesy/Reading Lights
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Courtesy/Reading Lights Both lights in the overhead console and rear passenger compartment will illuminate as courtesy lights when a door is opened, when the dimmer control is rotated to the courtesy light position (full right position), or when the UNLOCK button is pressed on the Remote Keyless Entry (RKE) transmitter, if equipped.
Page 146: Garage Door Opener - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 NOTE: The courtesy/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. If the interior lights are left on after the ignition is turned OFF, they will extinguish after 15 minutes.
Page 147 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The HomeLink buttons are located in the overhead WARNING! console, and contain one, two or three dots/lines desig- • Your motorized door or gate will open and close nating the different HomeLink channels. while you are training the Universal Transceiver.
Page 148: Programming Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 2. Place the handheld transmitter 1 to 3 in (3 to 8 cm) Programming HomeLink from the HomeLink buttons while keeping the EVIC Before You Begin display in view. If you have not trained any of the HomeLink buttons, erase all channels before you begin training.
Page 149 148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Some gate operators and garage door openers This can usually be found where the hanging antenna may require you to replace Step 3 with procedures noted wire is attached to the garage door opener motor (it is in the “Gate Operator/Canadian Programming”...
Page 150: Gate Operator/Canadian Programming
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 6. Firmly press and release the LEARN or TRAINING Gate Operator/Canadian Programming button. The name and color of the button may vary by Canadian radio-frequency laws require transmitter sig- manufacturer. nals to “time-out” (or quit) after several seconds of transmission –...
Page 151: Using Homelink
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE successfully accepted the frequency signal. The EVIC 1. Turn the ignition switch to the ON/RUN position. display will change from “CHANNEL # TRAINING” to 2. Press and hold the desired HomeLink button for “CHANNEL # TRAINED.”...
Page 152: Troubleshooting Tips
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Troubleshooting Tips General Information If you are having trouble programming HomeLink , here This device complies with FCC rules Part 15 and Industry are some of the most common solutions: Canada RSS-210. Operation is subject to the following two conditions: •...
Page 153: Power Sunroof - If Equipped
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED WARNING! The power sunroof switch is located on the overhead • Never leave children alone in a vehicle. Leaving console between the courtesy/reading lights. unattended children in a vehicle is dangerous for a number of reasons.
Page 154: Open Sunroof - Express Mode
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 sunroof will automatically retract. Remove the obstruc- Open Sunroof — Express Mode Momentarily pressing the switch rearward will activate tion if this occurs. Next, press the switch forward and the Express Open Feature, causing the sunroof to open release to Express Close.
Page 155: Sunshade Operation
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunshade Operation Sunroof Maintenance The sunshade can be opened manually. However, the Use only a non-abrasive cleaner and a soft cloth to clean sunshade will open automatically as the sunroof opens. the glass panel. NOTE: The sunshade cannot be closed if the sunroof is Sunroof Fully Closed open.
Page 156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 NOTE: • To ensure proper operation a MOPAR knob and element must be used. • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced.
Page 157 156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Inside the upper lid of the center storage compartment — if equipped. Power Outlet — Rear Center Console The key symbol indicates that this outlet can supply power when the key is in the ON/RUN or ACC posi- Power Outlet —...
Page 158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 All accessories connected to the outlet(s) should be CAUTION! removed or turned off when the vehicle is not in use to • Many accessories that can be plugged in draw protect the battery against discharge. power from the vehicle’s battery, even when not in WARNING! use (i.e., cellular phones, etc.).
Page 159: Cigar Lighter And Ash Receiver - If Equipped
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CIGAR LIGHTER AND ASH RECEIVER — IF EQUIPPED A removable ash receiver and cigar lighter are available. For vehicles with a bench seat the cupholder tray can be used to hold the ash receiver. Ash Receiver and Cigar Lighter (Bench Seat) 1 —...
Page 160: Power Inverter - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 For vehicles equipped with an optional floor shifter. POWER INVERTER — IF EQUIPPED A 115 Volt (150 Watts Maximum) outlet is located on the center stack of the instrument panel, to the right of the radio.
Page 161 160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The power inverter is designed with built-in overload protection. If the power rating of 150 Watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet the inverter should automatically reset.
Page 162: Cupholders
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 NOTE: CUPHOLDERS • When the power inverter switch is pressed, there will Front Instrument Panel Cupholders — (40–20–40 be a delay of approximately one second before the Seats) power inverter status indicator turns on. The status The cupholders are located in the pull-out tray at the indicator of the AC power inverter indicates whether bottom of the center stack.
Page 163: Front Instrument Panel Cupholders - Floor Mounted Shifter
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Instrument Panel Cupholders — Floor Rear Cupholder — Quad Cab Mounted Shifter Quad Cab vehicles may be equipped with a rear cup- For vehicles equipped with bucket seats and a floor holder that consists of two cup wells for rear passenger mounted shifter there are two cupholders located in the convenience.
Page 164: Rear Cupholder - Crew Cab
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 Rear Cupholder — Crew Cab STORAGE Crew Cab vehicles are equipped with rear cupholders Glove Box Storage located in the center armrest. The glove box is located on the passenger side of the instrument panel and features both an upper and lower storage area.
Page 165 164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To open the upper glove box push upward on the handle To open the lower glove box, pull on the handle to release release. The glove box door will automatically open. the latch and lower the door. Upper Glove Box Lower Glove Box...
Page 166: Door Storage
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 Door Storage Rear Door Storage — Crew Cab Storage compartments are located in both the driver and Front Door Storage — If Equipped passenger door trim panels. Storage areas and bottle holders (drivers side only) are located in the door trim panels.
Page 167: Center Storage Compartment - If Equipped
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Center Storage Compartment — If Equipped WARNING! The center storage compartment is located between the • This armrest is not a seat. Anyone seated on the driver and passenger seats. The storage compartment provides an armrest and contains both and upper and armrest could be seriously injured during vehicle lower storage area.
Page 168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 Upper Storage Compartment Lower Storage Bin With the upper lid closed, pull on the lower handle to open the lower storage bin.
Page 169: Second Row In-Floor Storage Bin - If Equipped
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Second Row In-Floor Storage Bin — If Equipped To open in-floor storage bin, lift upward on the handle of In-floor storage bins are located in front of the second the latch and open the lid. row seats and can be used for extra storage.
Page 170: Seatback Storage
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 Seatback Storage Storage (Regular Cab) Located in the back of both the driver and passenger The storage bin is located behind the front seats and runs front seats are pockets that can be used for storage. the length of the cab.
Page 171: Storage And Seats (Crew Cab)
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage and Seats (Crew Cab) CAUTION! The Crew Cab models provide additional storage under the rear seats. Lift the seats to access the storage com- Always lift the storage compartment lids by using partment.
Page 172: Rear Window Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 when the rear window defroster is on. The rear window defroster automatically turns off after approximately 10 minutes. For an additional five minutes of operation, press the button a second time. NOTE: To prevent excessive battery drain, use the rear window defroster only when the engine is operating.
Page 173: Power Sliding Rear Window - If Equipped
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) • Do not use scrapers, sharp instruments, or abra- sive window cleaners on the interior surface of the window. • Keep all objects a safe distance from the window. Power Sliding Rear Window — If Equipped The switch for the power sliding rear window is located on the overhead console.
Page 174: Fold Flat Load Floor - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 Unfolding the Load Floor FOLD FLAT LOAD FLOOR — IF EQUIPPED Quad Cab models with a 60/40 rear seat may be 1. Lift the 60/40 seat cushion(s) to the upward position. equipped with a folding load floor. WARNING! Do not operate the vehicle with loose items stored on the load floor.
Page 175 174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Grasp the knob on the load floor and lift the knob until Positioning the Load Floor for Storage Access Under the load floor unfolds into position. the Seat 1. Lift the 60/40 seat cushion(s) to the upward position. 2.
Page 176: Rambox - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 RAMBOX — IF EQUIPPED The RamBox system is an integrated pickup box storage and cargo management system consisting of three fea- tures: • Integrated box side storage bins • Cargo extender/divider • Bed rail tie-down system Load Floor Securing Straps 4.
Page 177: Rambox Integrated Box Side Storage Bins
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE RamBox Integrated Box Side Storage Bins CAUTION! Cargo storage bins are located on both sides of the pickup box. The cargo storage bins provide watertight, lockable, Failure to follow the following items could cause illuminated storage for up to 150 lbs (68 kg) of evenly damage to the vehicle: •...
Page 178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 RamBox Pushbutton and Lock RamBox Light Switch The interior of the RamBox will automatically illumi- nate when the lid is opened. In addition to the automatic illumination switch, there is a manual on/off switch located at the rear of each storage bin.
Page 179 178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! CAUTION! (Continued) • Loads applied to the top of the bin lid should be Leaving the lid open for extended periods of time minimized to prevent damage to the lid and could cause the vehicle battery to discharge. If the lid latching/hinging mechanisms.
Page 180: Rambox Safety Warning
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 RamBox Safety Warning RamBox Storage Bin Cover Emergency Release Carefully follow these warnings to help prevent personal Lever — If Equipped injury or damage to your vehicle: As a security measure, a Storage Bin Cover Emergency Release is built into the storage bin cover latching mecha- WARNING! nism.
Page 181: Bed Extender - If Equipped
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In the event of an individual being locked inside 1. Make sure the center handle is unlocked using the the storage bin, the storage bin cover can be opened from vehicle key and rotate the center handle vertically to inside of the bin by pulling on the glow-in-the-dark lever release the extender side gates.
Page 182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 2. With the side gates open, position the extender fully 3. Rotate the side gates closed allowing the outboard forward in the bed against the front panel. ends to be positioned in front of the cargo tie down loops. Storage Position Cargo Tie Down Loop...
Page 183 182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Rotate the center handle horizontally to secure the side Divider Position gates in the closed position. The divider position is intended for managing your cargo and assisting in keeping cargo from moving around the bed.
Page 184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 Center Handle and Lock Aligning Gate To Slots 3. Rotate the side gates closed so that the outboard ends 1 — Center Handle Lock 2 — Handle are secured into the intended slots of the bed. 2.
Page 185 184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Rotate the center handle horizontally to secure the side Extender Position gates in the closed position. The extender position allows you to load the bed of the truck beyond the tail gate. The bed extender will add an additional 15 in (38 cm) in the back of the truck when additional cargo room is needed.
Page 186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 To install the bed extender into the extender position perform the following: 1. Lower the tailgate. 2. Make sure the center handle is unlocked and rotate the center handle vertically in order to release the extender side gates.
Page 187 186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Rotate the handles to the horizontal position to secure WARNING! into place. To reduce the risk of potential injury or property damage: • Cargo must be secured. • Do not exceed cargo load rating of your vehicle. •...
Page 188: Bed Rail Tie-Down System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 Bed Rail Tie-Down System CAUTION! The maximum load per cleat should not exceed 250 lbs (113 kg) and the angle of the load on each cleat should not exceed 60 degrees above horizontal, or damage to the cleat or cleat rail may occur.
Page 189 188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE out on the cleat and slide it to the detent nearest the To remove the cleats from the utility rail, remove the end desired location. Make sure the cleat is seated in the cap by pushing up on the locking tab, located on the detent and tighten the nut.
Page 190: Slide-In Campers
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 SLIDE-IN CAMPERS Disconnecting the Rear Camera — If Equipped Camper Applications 1. Open the tailgate to access the rear camera connector Certain truck models are not recommended for slide-in bracket located on the rear sill. campers.
Page 191: Removing The Tailgate
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Remove the connector bracket from the sill by press- 4. Connect the chassis plug and bracket (provided in the ing inward in the locking tab. glove box) to the chassis wiring harness and insert the bracket back into the sill.
Page 192: Locking Tailgate - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 2. Unlatch the tailgate and remove the support cables by 5. Remove the tailgate from the vehicle. releasing the lock tang from the pivot. NOTE: Do not carry the tailgate loose in the truck pickup box.
Page 194: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....197 EVIC Displays ..... . 221 Switch Bank Button Description .
Page 195 194 UNDERSTANDING YOUR INSTRUMENT PANEL Media Center 730N/430 (RER/REN/RBZ) — Notes On Playing MP3 Files ... . 248 AM/FM Stereo Radio And CD/DVD/HDD/ Operation Instructions - Auxiliary Mode ..251 NAV —...
Page 196 UNDERSTANDING YOUR INSTRUMENT PANEL 195 Using This Feature ....266 Operating Instructions - Uconnect™ Multimedia (Satellite) Mode ... . . 272 Controlling The iPod Using Radio Buttons .
Page 197 196 UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Temperature Control (ATC) — Window Fogging And Frosting ..289 If Equipped ......283 Outside Air Intake .
Page 198: Instrument Panel Features
UNDERSTANDING YOUR INSTRUMENT PANEL 197 INSTRUMENT PANEL FEATURES 1 — Headlight Switch 7 — 115v Power Inverter Outlet 13 — Transfer Case Position Switch 2 — Instrument Cluster 8 — Power Outlet 14 — Ignition Switch 3 — Radio 9 — Lower Switch Bank 15 —...
Page 199: Switch Bank Button Description
198 UNDERSTANDING YOUR INSTRUMENT PANEL SWITCH BANK BUTTON DESCRIPTION 1. TOW/HAUL Refer to “Starting And Operating” for more information. Upper Switch Bank 2. ESP OFF The upper switch bank is located on the center of the Refer to “Starting And Operating” for more information. instrument panel.
Page 200: Lower Switch Bank
UNDERSTANDING YOUR INSTRUMENT PANEL 199 Lower Switch Bank 1. HEATED SEATS Refer to “Understanding The Features Of Your Vehicle” The lower switch bank is located on the center of the for more information. instrument panel. 2. VENTILATED SEATS Refer to “Understanding The Features Of Your Vehicle” for more information.
Page 201: Instrument Cluster - Base
200 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — BASE...
Page 202: Instrument Cluster - Premium
UNDERSTANDING YOUR INSTRUMENT PANEL 201 INSTRUMENT CLUSTER — PREMIUM...
Page 203: Instrument Cluster Descriptions
202 UNDERSTANDING YOUR INSTRUMENT PANEL • Check for an inoperative outside light bulb if either INSTRUMENT CLUSTER DESCRIPTIONS indicator remains on and does not flash, or flashes at a 1. Tachometer rapid rate. The Tachometer indicates engine speed in revolutions per minute.
Page 204 UNDERSTANDING YOUR INSTRUMENT PANEL 203 5. Speedometer CAUTION! The speedometer shows the vehicle speed in miles per hour and/or kilometers per hour (mph/km/h). Driving with a hot engine cooling system could damage your vehicle. If temperature gauge reads “H” pull over 6.
Page 205 204 UNDERSTANDING YOUR INSTRUMENT PANEL 7. Electronic Throttle Control (ETC) Light For vehicles equipped with a premium cluster this indi- This light informs you of a problem with the cator will display in the Electronic Vehicle Information Electronic Throttle Control (ETC) system. The Center (EVIC).
Page 206 UNDERSTANDING YOUR INSTRUMENT PANEL 205 10. SERV (Service) 4WD 12. Electronic Stability Program (ESP) Indicator Light The SERV 4WD light monitors the electric shift If this indicator light flashes during accelera- four-wheel drive system. If the SERV 4WD tion, apply as little throttle as possible. While light stays on or comes on during driving, it driving, ease up on the accelerator.
Page 207 206 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If the gauge pointer moves to either extreme of the same as it was before the repair or service. If s/he the gauge, the Check Gauges indicator will illuminate cannot do so, then the odometer must be set at zero, and and a single chime will sound.
Page 208 UNDERSTANDING YOUR INSTRUMENT PANEL 207 display the engine hour value. The engine hours will be Vehicle Odometer Messages When the appropriate conditions exist, the following displayed for a period of 30 seconds until the ignition is messages will display in the odometer: turned OFF or the engine is started.
Page 209 208 UNDERSTANDING YOUR INSTRUMENT PANEL If the vehicle diagnostic system determines damaged, a “noFUSE” message will display in the odom- that the fuel filler cap is loose, improperly eter display area. For further information on fuses and installed, or damaged, a loose gascap indicator fuse locations refer to “Fuses”...
Page 210 UNDERSTANDING YOUR INSTRUMENT PANEL 209 the oil change indicator system (after performing the pass H, the indicator will continuously flash and a scheduled maintenance), refer to the following proce- continuous chime will occur until the engine is allowed dure: to cool. 1.
Page 211 210 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: In vehicles with 4.7L or 5.7L engines, the highest switch the headlights to high beam, and pull toward available transmission gear is displayed in the lower yourself (normal position) to return to low beam. right corner of the Electronic Vehicle Information Center 21.
Page 212 UNDERSTANDING YOUR INSTRUMENT PANEL 211 condition has been corrected. If the problem is related to 22. Cargo Light The cargo light will illuminate when the cargo the brake booster, the ABS pump will run when applying light is activated by pressing the cargo light the brake and a brake pedal pulsation may be felt during button on the headlight switch.
Page 213 212 UNDERSTANDING YOUR INSTRUMENT PANEL The light also will turn on when the parking brake is WARNING! applied with the ignition switch in the ON position. Driving a vehicle with the red brake light on is NOTE: This light shows only that the parking brake is dangerous.
Page 214 UNDERSTANDING YOUR INSTRUMENT PANEL 213 Center (EVIC). Refer to ”Electronic Vehicle Information possible, and inflate them to the proper pressure. Driving Center (EVIC) — If Equipped” for further information. on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also 25.
Page 215 214 UNDERSTANDING YOUR INSTRUMENT PANEL When the malfunction indicator is illuminated, the sys- CAUTION! tem may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety The TPMS has been optimized for the original of reasons, including the installation of replacement or equipment tires and wheels.
Page 216 UNDERSTANDING YOUR INSTRUMENT PANEL 215 Although your vehicle will usually be drivable and not 26. Malfunction Indicator Light (MIL) The Malfunction Indicator Light (MIL) is part of need towing, see your authorized dealer for service as an onboard diagnostic (OBDII) system which soon as possible.
Page 217 216 UNDERSTANDING YOUR INSTRUMENT PANEL 28. Front Fog Light Indicator — If Equipped WARNING! This indicator will illuminate when the front fog lights are on. A malfunctioning catalytic converter, as referenced above, can reach higher temperatures than in normal 29. Anti-Lock Brake (ABS) Light operating conditions.
Page 218 UNDERSTANDING YOUR INSTRUMENT PANEL 217 30. Transmission Temperature Warning Light WARNING! This light indicates that there is excessive trans- mission fluid temperature that might occur In some circumstances a Transmission Temperature with severe usage such as trailer towing. It may Warning Light, under continued operation, could also occur when operating the vehicle in a high cause the fluid to boil over, come in contact with hot...
Page 219 218 UNDERSTANDING YOUR INSTRUMENT PANEL remain on continuously. Refer to “Occupant Restraints” Center (EVIC). Refer to ”Electronic Vehicle Information in “Things To Know Before Starting Your Vehicle” for Center (EVIC) — If Equipped” for further information. further information. 33. Electronic Stability Program (ESP) Indicator Light 32.
Page 220: Electronic Vehicle Information Center (Evic) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 219 Center (EVIC). Refer to ”Electronic Vehicle Information Center (EVIC) — If Equipped” for further information. WARNING! If a warning light remains on the system may not be working and you will not have the benefit of ESP or BAS.
Page 221 220 UNDERSTANDING YOUR INSTRUMENT PANEL This system conveniently allows the driver to select a Steering wheel EVIC control button, as variety of useful information by pressing the switches it appears on the left side of the steer- mounted on the steering wheel. The EVIC consists of the ing wheel.
Page 222: Evic Displays
UNDERSTANDING YOUR INSTRUMENT PANEL 221 • Door(s) Ajar (with a single chime, if vehicle is in Steering wheel EVIC control button as it appears on the right side of the motion) steering wheel. • Wrong Key • Damaged Key • Key not programmed •...
Page 223 222 UNDERSTANDING YOUR INSTRUMENT PANEL • Left Front Turn Signal Light Out EVIC Warning Lights • Left Rear Turn Signal Light Out • Door Ajar This light will turn on to indicate that one or • Right Front Turn Signal Light Out more door may be ajar.
Page 224 UNDERSTANDING YOUR INSTRUMENT PANEL 223 • Charging System Light • Electronic Throttle Control (ETC) Light This light shows the status of the electrical charg- This light informs you of a problem with the ing system. The light should come on when the Electronic Throttle Control (ETC) system.
Page 225 224 UNDERSTANDING YOUR INSTRUMENT PANEL • Engine Temperature Warning Light • SERV 4WD This light warns of an overheated engine condi- The SERV 4WD light monitors the electric shift tion. As temperatures rise and the gauge ap- 4WD system. If the SERV 4WD light stays on or proaches H, this indicator will illuminate and a comes on during driving, it means that the single chime will sound after reaching a set threshold.
Page 226 UNDERSTANDING YOUR INSTRUMENT PANEL 225 cycles and the vehicle has been driven several miles at WARNING! speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible. In some circumstances a Transmission Temperature Indicator, under continued operation, could cause the •...
Page 227: Distance To Empty (Dte)
226 UNDERSTANDING YOUR INSTRUMENT PANEL Oil Change Due 2. Fully depress the accelerator pedal slowly three times Your vehicle is equipped with an engine oil change within 10 seconds. indicator system. The Oil Change Due message will 3. Turn the ignition switch to the OFF position. flash in the EVIC display for approximately 10 seconds after a single chime has sounded to indicate the next NOTE: If the indicator message illuminates when you...
Page 228: Average Fuel Economy / Fuel Saver Mode - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 227 When the DTE value is less than 30 miles (48 km) will appear whenever MDS (if equipped) allows the estimated driving distance, the DTE display will change engine to operate on four cylinders, or if you are driving to a text display of LOW FUEL.
Page 229: Trip Functions
228 UNDERSTANDING YOUR INSTRUMENT PANEL • Trip B Trip Functions Press and release the ODOMETER/TRIP ODOMETER Shows the total distance traveled for Trip B since the last button until one of the following Trip Functions displays reset. in the EVIC: •...
Page 230: System (Customer Information Features)
UNDERSTANDING YOUR INSTRUMENT PANEL 229 System (Customer Information Features) Compass / Temperature Display Press and release the UP or DOWN button until “SYS- The compass readings indicate the direction TEM” displays in the EVIC and press the SELECT button. the vehicle is facing. Press and release the Press the UP and DOWN button to scroll through the compass button to display one of eight available information displays, then press SELECT to...
Page 231 230 UNDERSTANDING YOUR INSTRUMENT PANEL blocked or reduced airflow to the underhood ambient NOTE: A good calibration requires a level surface and temperature sensor caused by the snowplow. In addi- an environment free from large metallic objects such as tion, on vehicles equipped with Automatic Tempera- buildings, bridges, underground cables, railroad tracks, ture Control (ATC), it is suggested that the interior etc.
Page 232 UNDERSTANDING YOUR INSTRUMENT PANEL 231 5. Complete one or more 360–degree turns (in an area free from large metal or metallic objects) until the “CAL” indicator turns off. The compass will now function normally. Compass Variance Compass Variance is the difference between Magnetic North and Geographic North.
Page 233: Customer-Programmable Features (System Setup)
232 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Press the DOWN button until the “Compass Variance” Use the UP or DOWN button to display one of the message is displayed in the EVIC, then press the SELECT following choices. button. The last variance zone number displays in the Select Language EVIC.
Page 234 UNDERSTANDING YOUR INSTRUMENT PANEL 233 the feature showing the system has been activated or the Auto Lock Doors check-mark is removed, showing the system has been When this feature is selected, all doors will lock auto- deactivated. matically when the vehicle reaches a speed of 15 mph (24 km/h).
Page 235 234 UNDERSTANDING YOUR INSTRUMENT PANEL 1st Press RKE check-mark appears next to the feature showing the When Driver Door 1st Press is selected, only the driver’s system has been activated or the check-mark is removed, door will unlock on the first press of the RKE transmitter showing the system has been deactivated.
Page 236 UNDERSTANDING YOUR INSTRUMENT PANEL 235 is pressed. To make your selection, press and release the with or without the sound horn on lock feature selected. SELECT button until a check-mark appears next to the To make your selection, press and release the SELECT feature showing the system has been activated or the button until a check-mark appears next to the feature check-mark is removed, showing the system has been...
Page 237 236 UNDERSTANDING YOUR INSTRUMENT PANEL a check-mark appears next to the feature showing the or the check-mark is removed, showing the system has system has been activated or the check-mark is removed, been deactivated. When this feature is deactivated, the showing the system has been deactivated.
Page 238 UNDERSTANDING YOUR INSTRUMENT PANEL 237 Tilt Mirror In Reverse Illuminated Approach When this feature is selected and the shift lever is placed When this feature is selected, the headlights will activate in reverse gear, the side mirrors tilt downward to allow and remain on for up to 90 seconds when the doors are the driver to see into the previous blind spot and avoid unlocked with the RKE transmitter.
Page 239: Media Center 730N/430 (Rer/Ren/Rbz) - Am/Fm Stereo Radio And Cd/Dvd/Hdd/Nav - If Equipped
238 UNDERSTANDING YOUR INSTRUMENT PANEL Display Fuel Saver — If Equipped MEDIA CENTER 730N/430 (RER/REN/RBZ) — The “Fuel Saver Mode” message is located in the AM/FM STEREO RADIO AND CD/DVD/HDD/NAV — Compass/Temperature display, this message can be IF EQUIPPED turned on or off. To make your selection, press and NOTE: The sales code is located on the lower right side release the FUNCTION SELECT button until “ON”...
Page 240: Operating Instructions - Uconnect™ Phone - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 239 displayed. To move the minute backward, touch the Operating Instructions — Uconnect™ Phone — If Equipped screen where the word “Min” with the arrow pointing Refer to “Uconnect™ Phone” in the Uconnect™ User downward is displayed. Manual located on the DVD for further details.
Page 241: Clock Setting Procedure - Rer/Ren Radio
240 UNDERSTANDING YOUR INSTRUMENT PANEL Show Time if Radio is Off 3. Touch the screen where the words “Set Time Zone” are When selected, this feature will display the time of day displayed. The time zone selection menu will appear on on the touch screen when the radio is turned off.
Page 242 UNDERSTANDING YOUR INSTRUMENT PANEL 241 6. To save the new time setting, touch the screen where To Manually Set the Clock — RER/REN the word “Save” is displayed. 1. Turn on the radio. Changing Daylight Savings Time 2. Touch the screen where the time is displayed. When selected, this feature will display the time of day in 3.
Page 243 242 UNDERSTANDING YOUR INSTRUMENT PANEL Show Time if Radio is Off Changing the Time Zone When selected, this feature will display the time of day 1. Turn on the radio. on the touch screen when the radio is turned off. Proceed as follows to change the current setting: 2.
Page 244: Media Center 130 (Res) - Am/Fm Stereo Radio With Cd Player (Mp3 Aux Jack)
UNDERSTANDING YOUR INSTRUMENT PANEL 243 MEDIA CENTER 130 (RES) — AM/FM STEREO Operating Instructions — Radio Mode RADIO WITH CD PLAYER (MP3 AUX JACK) NOTE: The ignition switch must be in the ON or ACC NOTE: The radio sales code is located on the lower right position to operate the radio.
Page 245 244 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons 4. Adjust the minutes using the right side TUNE/ Press and release the SEEK buttons to search for the next SCROLL control knob. Press the TUNE/SCROLL control listenable station in AM/FM mode. Press the right switch knob to save time change.
Page 246 UNDERSTANDING YOUR INSTRUMENT PANEL 245 Push the rotary TUNE/SCROLL control knob a second Push the rotary TUNE/SCROLL control knob again to time and MID will display. Turn the TUNE/SCROLL exit setting tone, balance, and fade. control knob to the right or left to increase or decrease the AM/FM Button mid-range tones.
Page 247: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
246 UNDERSTANDING YOUR INSTRUMENT PANEL SET 2 in both AM and FM. This allows a total of 12 AM Operation Instructions — CD MODE For CD And and 12 FM stations to be stored into pushbutton memory. MP3 Audio Play The stations stored in SET 2 memory can be selected by NOTE: pressing the pushbutton twice.
Page 248 UNDERSTANDING YOUR INSTRUMENT PANEL 247 If you insert a disc with the ignition ON and the radio EJECT Button - Ejecting a CD ON, the unit will switch from radio to CD mode and Press the EJECT button to eject the CD. begin to play when you insert the disc.
Page 249: Notes On Playing Mp3 Files
248 UNDERSTANDING YOUR INSTRUMENT PANEL the current selection. Pressing and holding the SEEK SET/RND Button (Random Play Button) button will allow faster scrolling through the tracks in Press this button while the CD is playing to activate CD and MP3 modes. Random Play.
Page 250 UNDERSTANDING YOUR INSTRUMENT PANEL 249 exceeding 20 folders will result in this display. With Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 200 files, exceeding 50 folders will result in this Level 1 and Level 2 and includes the Joliet extension. display.) When reading discs recorded using formats other than •...
Page 251 250 UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats MPEG Sampling Bit Rate (kbps) The radio will recognize only files with the *.MP3 exten- Specification Frequency (kHz) sion as MP3 files. Non-MP3 files named with the *.MP3 160, 128, 144, extension may cause playback problems.
Page 252: Operation Instructions - Auxiliary Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 251 Loading times for playback of MP3 files may be affected MP3 player, or cassette player, and utilize the vehicle’s by the following: audio system to amplify the source and play through the vehicle speakers. • Media - CD-RW media may take longer to load than CD-R media Pressing the DISC/AUX button will change the mode to auxiliary device if the AUX jack is connected.
Page 253: Media Center 130 (Res/Rsc) - Am/Fm Stereo Radio With Cd Player (Mp3 Aux Jack) And Sirius Radio
252 UNDERSTANDING YOUR INSTRUMENT PANEL MEDIA CENTER 130 (RES/RSC) — AM/FM Operating Instructions — Radio Mode STEREO RADIO WITH CD PLAYER (MP3 AUX NOTE: The ignition switch must be in the ON or ACC JACK) AND SIRIUS RADIO position to operate the radio. NOTE: The radio sales code is located on the lower right Power Switch/Volume Control (Rotary) side of the radio faceplate.
Page 254 UNDERSTANDING YOUR INSTRUMENT PANEL 253 to seek up and the left switch to seek down. The radio Phone Button Uconnect™ Phone — If Equipped will remain tuned to the new station until you make Press this button to operate the Uconnect™ Phone feature another selection.
Page 255 254 UNDERSTANDING YOUR INSTRUMENT PANEL 3. After adjusting the hours, press the right side TUNE/ INFO Button SCROLL control knob to set the minutes. The minutes Press the INFO button for an RDS station (one with call will begin to blink. letters displayed).
Page 256 UNDERSTANDING YOUR INSTRUMENT PANEL 255 Push the rotary TUNE/SCROLL control knob a fifth time Setting the Tone, Balance, and Fade Push the rotary TUNE/SCROLL control knob and BASS and FADE will display. Turn the TUNE/SCROLL control will display. Turn the TUNE/SCROLL control knob to knob to the left or right to adjust the sound level between the right or left to increase or decrease the bass tones.
Page 257 256 UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the MUSIC TYPE button to select the following 16-Digit Character Program Type format types: Display 16-Digit Character Personality Persnlty Program Type Display Public Public No program type Rhythm and Blues R & B None or undefined Religious Music Rel Musc...
Page 258 UNDERSTANDING YOUR INSTRUMENT PANEL 257 By pressing the SEEK button when the Music Type icon the minutes using the right side TUNE/SCROLL is displayed, the radio will be tuned to the next frequency control knob. Press the TUNE/SCROLL control knob station with the same selected Music Type name.
Page 259: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
258 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each pushbutton by Operation Instructions — CD MODE for CD and repeating the above procedure with this exception: Press MP3 Audio Play the SET/RND button twice and SET 2 will show in the NOTE: display window.
Page 260 UNDERSTANDING YOUR INSTRUMENT PANEL 259 If you insert a disc with the ignition ON and the radio EJECT Button - Ejecting a CD ON, the unit will switch from radio to CD mode and Press the EJECT button to eject the CD. begin to play when you insert the disc.
Page 261: Notes On Playing Mp3 Files
260 UNDERSTANDING YOUR INSTRUMENT PANEL the current selection. Pressing and holding the SEEK SET/RND Button (Random Play Button) button will allow faster scrolling through the tracks in Press this button while the CD is playing to activate CD and MP3 modes. Random Play.
Page 262 UNDERSTANDING YOUR INSTRUMENT PANEL 261 exceeding 20 folders will result in this display. With Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 200 files, exceeding 50 folders will result in this Level 1 and Level 2 and includes the Joliet extension. display.) When reading discs recorded using formats other than •...
Page 263 262 UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats MPEG Sampling Bit Rate (kbps) The radio will recognize only files with the *.MP3 exten- Specification Frequency (kHz) sion as MP3 files. Non-MP3 files named with the *.MP3 160, 128, 144, extension may cause playback problems.
Page 264: List Button (Cd Mode For Mp3 Play)
UNDERSTANDING YOUR INSTRUMENT PANEL 263 Loading times for playback of MP3 files may be affected begin playing the files contained in that folder (or the by the following: next folder in sequence if the selection does not contain playable files). •...
Page 265: Universal Consumer Interface (Uci) - If Equipped
264 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - Auxiliary Mode Operating Instructions - Uconnect™ Phone (If The auxiliary (AUX) jack is an audio input jack which Equipped) allows the user to plug in a portable device such as an Refer to “Uconnect™ Phone” in the Uconnect™ User MP3 player or cassette player and utilize the vehicle’s Manual located on the DVD for further details.
Page 266: Connecting The Ipod
UNDERSTANDING YOUR INSTRUMENT PANEL 265 This feature allows you to plug an iPod into the Connecting The iPod vehicle’s sound system through a 16–pin connector, using Use the provided connection cable to connect an iPod to the provided interface cable. the vehicle’s 16–pin connector port (which is located in the glove compartment on some vehicles).
Page 267: Using This Feature
266 UNDERSTANDING YOUR INSTRUMENT PANEL Using This Feature Play Mode By using the provided connection cable to connect an When switched to UCI mode, the iPod automatically iPod to the vehicle’s UCI 16–pin connector port: starts Play mode. In Play mode, you may use the following buttons on the radio faceplate to control the •...
Page 268 UNDERSTANDING YOUR INSTRUMENT PANEL 267 • Jump backward in the current track by pressing and • While a track is playing, press the INFO button to see holding the << RW button. Holding the << RW the associated metadata (artist, track title, album, etc.) button long enough will take you to the beginning for that track.
Page 269: List Or Browse Mode
268 UNDERSTANDING YOUR INSTRUMENT PANEL • RND button (available on sales code RES radio only): knob fast will scroll through the list faster. During Pressing this button toggles between Shuffle ON and fast scroll, you may notice a slight delay in updating Shuffle OFF modes for the iPod .
Page 270 UNDERSTANDING YOUR INSTRUMENT PANEL 269 • Pressing a PRESET button will display the current CAUTION! list on the top line and the first item in that list on • Leaving the iPod (or any supported device) any- the second line. where in the vehicle in extreme heat or cold can •...
Page 271: Uconnect™ Multimedia (Satellite Radio) - If Equipped (Ren/Rer/Rbz/Res Radios Only)
270 UNDERSTANDING YOUR INSTRUMENT PANEL Uconnect™ Multimedia (SATELLITE RADIO) — IF information, call the toll-free number 888-539-7474, or EQUIPPED (REN/RER/RBZ/RES RADIOS ONLY) visit the Sirius web site at www.sirius.com, or at www- Satellite radio uses direct satellite-to-receiver broadcast- .siriuscanada.ca for Canadian residents. ing technology to provide clear digital sound, coast to Electronic Serial Number/Sirius Identification coast.
Page 272: Selecting Uconnect™ Multimedia (Satellite)
UNDERSTANDING YOUR INSTRUMENT PANEL 271 Sirius ID number will display. The Sirius ID number bikes should be placed as far rearward as possible, within display will time out in two minutes. Press any button on the loading design of the rack. Do not place items directly the radio to exit this screen.
Page 273: Operating Instructions - Uconnect™ Multimedia (Satellite) Mode
272 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Uconnect™ Multimedia INFO Button (Satellite) Mode Pressing the INFO button will cycle the display informa- tion between Artist, Song Title, and Composer (if avail- NOTE: The ignition switch must be in the ON or ACC able).
Page 274 UNDERSTANDING YOUR INSTRUMENT PANEL 273 MUSIC TYPE Button SETUP Button Pressing this button once will turn on the Music Type Pressing the SETUP button allows you to select the mode for five seconds. Pressing the MUSIC TYPE button following items: or turning the TUNE/SCROLL control knob within five •...
Page 275: Operating Instructions - Uconnect™ Phone (If Equipped)
274 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second channel to each pushbutton by VIDEO ENTERTAINMENT SYSTEM (VES)™ — IF repeating the above procedure with this exception: Press EQUIPPED the SET button twice and SET 2 will show in the display The optional Video Entertainment System (VES)™...
Page 276 UNDERSTANDING YOUR INSTRUMENT PANEL 275 The LCD screen is located in the overhead compartment console. VES™ Remote Control Location NOTE: Refer to the “Uconnect™ Multimedia” section of Uconnect™ User Manual located on the DVD for further Overhead Video Screen details.
Page 277: Remote Sound System Controls - If Equipped
276 UNDERSTANDING YOUR INSTRUMENT PANEL REMOTE SOUND SYSTEM CONTROLS — IF The right hand control is a rocker type switch with a EQUIPPED pushbutton in the center. Pressing the top of the switch The remote sound system controls are located on the rear will increase the volume, and pressing the bottom of the surface of the steering wheel.
Page 278: Cd Player
UNDERSTANDING YOUR INSTRUMENT PANEL 277 The button located in the center of the left hand control CD/DVD DISC MAINTENANCE will tune to the next pre-set station that you have To keep a CD/DVD in good condition, take the following programmed in the radio pre-set pushbuttons. precautions: 1.
Page 279: Radio Operation And Cellular Phones
278 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particu- throughout the vehicle. The controls are located on the lar disc, it may be damaged (i.e., scratched, reflective instrument panel below the radio. coating removed, a hair, moisture or dew on the disc) NOTE: During snowplow usage on vehicles equipped oversized, or have protection encoding.
Page 280 UNDERSTANDING YOUR INSTRUMENT PANEL 279 dials and inner push knobs. These comfort controls can Front Blower Control be set to obtain desired interior conditions. There are four blower speeds. Use this control to regulate the amount of air forced through the system in any mode you select.
Page 281 280 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If your air conditioning performance seems Panel Mode lower than expected, check the front of the A/C con- Air is directed through the outlets in the instrument denser (located in front of the radiator), for an accumu- panel.
Page 282 UNDERSTANDING YOUR INSTRUMENT PANEL 281 Mix Mode Recirculation Control Air is directed through the floor, defrost and side Press this button to choose between window demist outlets. This setting works best in outside air intake or recirculation of cold or snowy conditions that require extra heat at the air inside the vehicle.
Page 283 282 UNDERSTANDING YOUR INSTRUMENT PANEL • Continuous use of the Recirculation mode may make NOTE: For maximum airflow to the rear, the center the inside air stuffy and window fogging may occur. instrument panel outlets can be directed toward the rear Extended use of this mode is not recommended.
Page 284 UNDERSTANDING YOUR INSTRUMENT PANEL 283 MAX A/C Automatic Temperature Control (ATC) — If For maximum cooling, when MAX Equipped A/C is selected the A/C is turned on • The Automatic Temperature Control (ATC) allows automatically and the air is recircu- both driver and front passenger seat occupants to lated.
Page 285 284 UNDERSTANDING YOUR INSTRUMENT PANEL • The system can be controlled manually, if desired. • SYNC feature links the temperature controls, the pas- senger side temperature becomes the same as the temperature selected by the driver. The ATC system automatically maintains the interior comfort level desired by the driver and all passengers.
Page 286 UNDERSTANDING YOUR INSTRUMENT PANEL 285 Automatic Operation NOTE: • It is not necessary to move the temperature settings for 1. Position the MODE control knob to the Auto position cold or hot vehicles. The system automatically adjusts on the Automatic Temperature Control (ATC) Panel. the temperature, mode and fan speed to provide 2.
Page 287 286 UNDERSTANDING YOUR INSTRUMENT PANEL blower will engage immediately if the Defrost mode is The blower fan speed can be set to any fixed speed by selected, or by adjusting the blower control knob and adjusting the blower control knob. The fan will now setting the fan to any fixed speed.
Page 288 UNDERSTANDING YOUR INSTRUMENT PANEL 287 NOTE: In many temperature positions, the BI-LEVEL NOTE: While operating in the other modes, the system mode is designed to provide cooler air out of the panel will not automatically sense the presence of fog, mist or outlets and warmer air from the floor outlets.
Page 289 288 UNDERSTANDING YOUR INSTRUMENT PANEL Recirculation Control Summer Operation When outside air contains smoke, odors, or The engine cooling system in air conditioned vehicles high humidity, or if rapid cooling is desired, must be protected with a high-quality antifreeze coolant you may wish to recirculate interior air by to provide proper corrosion protection and to protect pressing the RECIRCULATION control button.
Page 290 UNDERSTANDING YOUR INSTRUMENT PANEL 289 Vacation/Storage Outside Air Intake Any time you store your vehicle or keep it out of service Make sure the air intake, located directly in front of the (i.e., vacation) for two weeks or more, run the air windshield, is free of obstructions such as leaves.
Page 291 290 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips...
Page 292: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ....297 Brake/Transmission Interlock Manual Override ......301 Normal Starting .
Page 293 292 STARTING AND OPERATING Shifting Procedure – Manually Shifted Driving In Snow, Mud And Sand ..336 Transfer Case ..... . . 317 Crossing Obstacles Transfer Case Position Indicator Light .
Page 294 STARTING AND OPERATING 293 Driving Off-Road ..... 355 Four-Wheel Anti-Lock Brake System ..380 Winch Usage (Power Wagon Only) —...
Page 295 294 STARTING AND OPERATING Tires — General Information ... . . 404 Snow Tires ......414 Tire Pressure .
Page 296 STARTING AND OPERATING 295 Gasoline/Oxygenate Blends ... . . 428 Cruising Range ..... . 435 E-85 Usage In Non-Flex Fuel Vehicles .
Page 297 296 STARTING AND OPERATING Towing Requirements ....447 Recreational Towing – Two-Wheel Drive Models ......461 Towing Tips .
Page 298: Starting Procedures
STARTING AND OPERATING 297 STARTING PROCEDURES Normal Starting Before starting your vehicle, adjust your seat, adjust both Normal starting of either a warm or cold engine is inside and outside mirrors, and fasten your seat belt. obtained without pumping or pressing the accelerator pedal.
Page 299: If Engine Fails To Start
298 STARTING AND OPERATING Tip Start Feature WARNING! Do not press the accelerator. Turn the ignition switch • Never pour fuel or other flammable liquids into briefly to the START position and release it. The starter motor will continue to run but will automatically disen- the throttle body air inlet opening in an attempt to gage when the engine is running.
Page 300: After Starting
STARTING AND OPERATING 299 If the engine has been flooded, it may start to run, but not 1500 Models have enough power to continue running when the key The engine block heater cord is routed under the hood on fob is released. If this occurs, continue cranking with the the passenger side of the vehicle near the right head lamp accelerator pedal pushed all the way to the floor.
Page 301: Automatic Transmission
300 STARTING AND OPERATING WARNING! CAUTION! (Continued) • Do not shift from REVERSE, PARK, or NEUTRAL Remember to disconnect the cord before driving. into any forward gear when the engine is above Damage to the 110-115 Volt electrical cord could cause idle speed.
Page 302: Key Ignition Park Interlock
STARTING AND OPERATING 301 Key Ignition Park Interlock Brake/Transmission Interlock Manual Override This vehicle is equipped with a Key Ignition Park Inter- Column Shifter – If Equipped lock which requires the shift lever to be placed in PARK There is an override for the BTSI that allows you to move prior to turning the key fob to the LOCK position.
Page 303 302 STARTING AND OPERATING 5. Using the screwdriver, press and hold the override tab Center Console Shifter – If Equipped through the access port (ringed circle) on the bottom of There is an override for the BTSI that allows you to move the steering column.
Page 304: Four-Speed Automatic Transmission - If Equipped
STARTING AND OPERATING 303 Four–Speed Automatic Transmission – If Equipped NOTE: Under extremely cold temperatures (-6°F (-21°C) and when in DRIVE, transmission operation may be briefly limited to only second gear operation. Normal operation will resume once the transmission temperature has risen to a suitable level.
Page 305 304 STARTING AND OPERATING Never use PARK while the vehicle is in motion. Apply REVERSE the parking brake when leaving the vehicle in this range. This range is for moving the vehicle rearward. Use this Always apply the parking brake first, then place the shift range only after the vehicle has come to a complete stop.
Page 306 STARTING AND OPERATING 305 • the engine coolant has reached normal operating tem- 2 (Second) This range is for moderate grades and to assist braking perature on dry pavement or in mud and snow. Begins at a stop in • vehicle speed is above approximately 30 mph low gear with automatic upshift to second gear.
Page 307 306 STARTING AND OPERATING Temperature Warning Light” may illuminate and the transmission may downshift out of OVERDRIVE until the transmission cools down. After the transmission cools down, the transmission will resume normal operation. The transmission will downshift from OVERDRIVE to DRIVE if the accelerator pedal is fully pressed at vehicle speeds above approximately 35 mph (56 km/h).
Page 308 STARTING AND OPERATING 307 If the problem is no longer detected, the transmission will Transmission Limp Home Mode Transmission function is monitored for abnormal condi- return to normal operation. If the problem persists, tions. If a condition is detected that could result in PARK, REVERSE, and NEUTRAL will continue to oper- transmission damage, the Transmission Limp Home ate.
Page 309: Five-Speed Automatic Transmission - If Equipped
308 STARTING AND OPERATING Five–Speed Automatic Transmission – If into 3 (third gear), the transmission will never shift above Equipped third gear, but can shift down to 2 (second gear) or 1 (first The shift lever display located in the instrument panel gear), when needed.
Page 310 STARTING AND OPERATING 309 through third gear are underdrive gears, and fourth gear is direct drive. ERS fifth gear (Overdrive) is the same as the normal fourth gear. When in the DRIVE position in first through fourth gear, the first tap down (-), will display the ERS designation for the current gear (the transmission will not downshift).
Page 311 310 STARTING AND OPERATING Gear Ranges WARNING! Do not race the engine when shifting from PARK or NEUTRAL position into another gear range. Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their PARK grip and the vehicle could skid.
Page 312 STARTING AND OPERATING 311 NEUTRAL WARNING! (Continued) This range is for when the vehicle is standing for pro- • Your vehicle could move and injure you and others longed periods with the engine running. The engine may if it is not completely in PARK. Check by trying to be started in this range.
Page 313 312 STARTING AND OPERATING • the engine coolant (antifreeze) has reached normal Temperature Warning Light” may illuminate and the operating temperature; transmission may downshift out of Overdrive until the transmission cools down. After cool down, the transmis- • vehicle speed is above approximately 30 mph sion will resume normal operation.
Page 314 STARTING AND OPERATING 313 activated. Pressing the switch a second time restores normal operation. If the TOW/HAUL mode is desired, the button must be pressed each time the engine is started. Torque Converter Clutch A feature designed to improve fuel economy has been included in the automatic transmission on your vehicle.
Page 315: Four-Wheel Drive Operation - If Equipped
314 STARTING AND OPERATING torque converter clutch is not engaged, it may seem as transfer case. Refer to the operating instructions for your if the transmission is not shifting into Overdrive when transfer case, located in this section for further informa- cold.
Page 316 STARTING AND OPERATING 315 moving the shift lever to the desired positions. The 4H Proper operation of four-wheel drive vehicles depends and 4L positions are intended for loose, slippery road on tires of equal size, type and circumference on each surfaces only.
Page 317 316 STARTING AND OPERATING WARNING! Four-Wheel Drive High Range - This range locks the front and rear driveshafts together forcing the front and You or others could be injured if you leave the rear wheels to rotate at the same speed. Additional vehicle unattended with the transfer case in the traction for loose, slippery road surfaces only.
Page 318: Shifting Procedure - Manually Shifted Transfer Case
STARTING AND OPERATING 317 Shifting Procedure – Manually Shifted Transfer NOTE: • Pausing in transfer case NEUTRAL in vehicles Case equipped with an automatic transmission may require 2H ⇔ 4H shutting the engine OFF to avoid gear clash while Shifting between 2H and 4H can be made with the completing the shift.
Page 319: Transfer Case Position Indicator Light
318 STARTING AND OPERATING Transfer Case Position Indicator Light The “Transfer Case Position Indicator Light” in the instrument cluster is used to alert the driver that the front axle is fully engaged and all four wheels are driving. Electronically Shifted Transfer Case (Four-Position Switch) –...
Page 320 STARTING AND OPERATING 319 • Neutral (NEUTRAL) NOTE: The transfer case NEUTRAL position is selected by pressing the recessed button located on the lower left This electronically shifted transfer case is designed to be hand corner of the 4WD Control Switch. The transfer case driven in the two-wheel drive position (2WD) for normal NEUTRAL position is to be used for recreational towing street and highway conditions on dry, hard surfaced...
Page 321 320 STARTING AND OPERATING 3. When the shift is complete, the indicator light for the The “SVC 4WD Warning Light” monitors the electronic selected position will stop flashing and remain ON. shift four-wheel drive system. If this light remains on after engine start up or illuminates during driving, it If One Or More Shift Conditions Are Not Met: means that the four-wheel drive system is not function-...
Page 322 STARTING AND OPERATING 321 When operating your vehicle in 4WD LOW, the engine WARNING! speed is approximately three times that of the 2WD or 4WD LOCK positions at a given road speed. Take care You or others could be injured if you leave the not to overspeed the engine and do not exceed 25 mph vehicle unattended with the transfer case in the (40 km/h).
Page 323: Shifting Procedure
322 STARTING AND OPERATING 4WD LOCK Shifting Procedure Four-Wheel Drive Lock Range - This range locks the front NOTE: and rear driveshafts together forcing the front and rear • If any of the requirements to select a new transfer case wheels to rotate at the same speed.
Page 324 STARTING AND OPERATING 323 When the shift is complete, the position indicator light selected position indicator light will flash and the origi- for the selected position will stop flashing and remain nal position indicator light will remain ON. At this time, reduce speed and stop spinning the wheels to complete the shift.
Page 325: Electronically Shifted Transfer Case (Five-Position Switch) - If Equipped
324 STARTING AND OPERATING 3. While still rolling, rotate the transfer case control NOTE: • If Steps 1 or 2 of either the Preferred or Alternate switch to the desired position. Procedure are not satisfied prior to attempting the 4. After the desired position indicator light is ON (not shift, then the desired position indicator light will flash flashing), shift the transmission back into gear.
Page 326 STARTING AND OPERATING 325 • Four-wheel drive low range (4WD LOW) • Neutral (NEUTRAL) This electronically shifted transfer case is designed to be driven in the two–wheel drive position (2WD) or four- wheel drive position (4WD AUTO) for normal street and highway conditions on dry hard surfaced roads).
Page 327 326 STARTING AND OPERATING the front and rear driveshafts together forcing the front Transfer Case Position Indicator Lights and rear wheels to rotate at the same speed. This is The Transfer Case Position Indicator Lights (4WD, accomplished by rotating the 4WD Control Switch to the 4LOW, and 4WD AUTO) are located on the instrument desired position.
Page 328 STARTING AND OPERATING 327 2. The newly selected position indicator light will con- WARNING! tinue to flash. Always engage the parking brake when powering 3. The transfer case will not shift. down the vehicle if the “SVC 4WD Warning Light” is NOTE: Before retrying a selection, make certain that all illuminated.
Page 329 328 STARTING AND OPERATING Proper operation of four-wheel drive vehicles depends For additional information on the appropriate use of each on tires of equal size, type and circumference on each transfer case mode position, see the information below: wheel. Any difference in tire size can cause damage to the transfer case.
Page 330: Shifting Procedure
STARTING AND OPERATING 329 position will remain ON, and the newly selected 4WD LOW Four-Wheel Drive Low Range - This range provides low position indicator light will continue to flash until all speed four-wheel drive. Locks the front and rear drive- the requirements for the selected position have been shafts together forcing the front and rear wheels to rotate met.
Page 331 330 STARTING AND OPERATING the vehicle in motion, the transfer case will engage/ 2. Shift the transmission into NEUTRAL. disengage faster if you momentarily release the accelera- 3. While still rolling, rotate the transfer case control tor pedal after turning the control switch. If the vehicle is switch to the desired position.
Page 332: Axle Locker System (2500 Models Only) - If Equipped
STARTING AND OPERATING 331 NOTE: If Steps 1 or 2 of either the Preferred or Alternate stuck. The locking front and rear differentials should only Procedure are not satisfied prior to attempting the shift or be engaged during low-speed, extreme off-road situa- if they no longer are being met while the shift attempt is tions where one wheel is likely to not be in contact with in process, the desired position indicator light will flash...
Page 333 332 STARTING AND OPERATING The locking axles are controlled by the axle locker switch. To lock the rear axle, place the vehicle in 4LO. Refer to “Four Wheel Drive Operation” in “Starting and Operat- The switch has three positions, AXLE UNLOCK, REAR ing”...
Page 334: Safe Off-Road Driving - Power Wagon Only
STARTING AND OPERATING 333 NOTE: The axle lockers could be torque locked due to WARNING! side to side loads on the axle. Driving slowly while turning the steering wheel from a left hand turn to a right Do not use the locked axle position for normal hand turn or driving in REVERSE for a short distance driving.
Page 335 334 STARTING AND OPERATING (ORV) trails or recreation areas. You should always tread distance up the ramp divided by the wheelbase of the lightly and only use established roads, trails or ORV vehicle and multiplied by 1,000 is the RTI. This vehicle recreational areas.
Page 336 STARTING AND OPERATING 335 your vehicle’s steering, handling and traction. Control- CAUTION! ling your vehicle is one of the keys to successful off-road driving, so always keep a firm grip on the steering wheel The door sill height is 25 inches. Water may intrude and maintain a good driving posture.
Page 337: Driving In Snow, Mud And Sand
336 STARTING AND OPERATING steering, acceleration and braking inputs. Therefore you WARNING! should accelerate slowly, leave greater stopping distances and avoid abrupt vehicle maneuvers. You want to keep a Always wear your seat belt and firmly tie down slow constant steady pace. The key is to maintain the cargo.
Page 338 STARTING AND OPERATING 337 • Sand – Soft sand is very difficult to travel through CAUTION! with full tire pressure. When crossing soft sandy spots in a trail maintain your vehicle’s momentum and do On icy or slippery roads, do not downshift at high not stop.
Page 339: Crossing Obstacles (Rocks And Other High Points)
338 STARTING AND OPERATING forward until it makes contact with the object. Apply the CAUTION! throttle lightly while holding a light brake pressure and ease the vehicle up and over the object. Reduced tire pressures may cause tire unseating and total loss of air pressure.
Page 340 STARTING AND OPERATING 339 independently. You need to use caution when crossing Crossing Large Rocks When approaching large rocks, choose a path which large obstacles with steep sides. Do not attempt to cross ensures you drive over the largest with your tires. This any large obstacle with steep sides at an angle great will lift your undercarriage over the obstacle.
Page 341: Hill Climbing
340 STARTING AND OPERATING accelerator to avoid spinning the log out from under your CAUTION! tires. Then ease the vehicle off the log using your brakes. Winching or rocking the vehicle off hard objects CAUTION! increases the risk of underbody damage. Do not attempt to cross a log with a greater diameter Hill Climbing than the running ground clearance or the vehicle will...
Page 342 STARTING AND OPERATING 341 the vehicle if something goes wrong? If everything fresh bite into the surface and will usually provide looks good and you feel confident, then change trans- enough traction to complete the climb. If you do not mission into a lower gear, shift the transfer case into 4L make it to the top, place the vehicle in REVERSE and (Low) and proceed with caution.
Page 343 342 STARTING AND OPERATING ability to proceed then make sure you are in 4L (Low sure the surface has good traction with firm and stable Range) with the transmission in first gear (manually soils. If possible transverse the incline at an angle select first gear on automatic transmissions) and pro- heading slightly up or down.
Page 344: Driving Through Water
STARTING AND OPERATING 343 your vehicle’s abilities and be able to recover it if WARNING! something goes wrong. You should never stop or shut a vehicle off when crossing deep water unless you ingested If the engine stalls or you lose headway or cannot water into the engine air intake.
Page 345 344 STARTING AND OPERATING crossing is the water depth, current and bottom con- CAUTION! ditions. On soft bottoms the vehicle will sink in, effectively increasing the water level on the vehicle. Be Water ingestion into the axles, transmission, transfer sure to consider this when determining the depth and case, engine or vehicle interior can occur if you drive the ability to safely cross.
Page 346: Airing Down For Off-Road Driving
STARTING AND OPERATING 345 downstream out of control if the water is deep enough CAUTION! to push on the large surface area of the vehicle’s body. Before you proceed determine the speed of the current, Muddy waters can reduce the cooling system effec- the water’s depth, approach angle, bottom condition tiveness by depositing debris onto the radiator.
Page 347: Vehicle Recovery
346 STARTING AND OPERATING form to the ground contour. Different terrain, tires, and Vehicle Recovery vehicles require different tire pressure. Hard surfaces like If you drive off-road, you may encounter a situation rock and heavier vehicles require higher pressures than where you will need to recover your vehicle.
Page 348 STARTING AND OPERATING 347 • Rock Cycling Your Vehicle – Rock cycling your ve- vehicle impingement on the surroundings, then using a tow strap to the vehicle tow hooks would be fast and hicle is one of the easiest, fastest and most commonly easy.
Page 349 348 STARTING AND OPERATING straps together using a 1 ⁄ inch hard wood dowel. CAUTION! This will keep the straps from becoming knotted and is safer than using a clevis pin if the strap breaks. Next Damage can occur when spinning your tires at an have the tow vehicle backup, leaving two to three feet excessive high speed.
Page 350 STARTING AND OPERATING 349 out of the situation in a slow controlled manner. This WARNING! control works well for avoiding further vehicle dam- age. Once you decide it is time to use the winch look Never use tow straps with end hooks or link two for a good anchor point.
Page 351: After Driving Off-Road
350 STARTING AND OPERATING • Completely inspect the underbody of your vehicle. as you power the winch in. Be careful not to allow slack in the cable as you recover the vehicle. Do not try Check tires, body structure, steering, suspension, and to guide the cable into the drum.
Page 352: Limited-Slip Differential
STARTING AND OPERATING 351 packed material. Packed foreign material can cause a driving and cornering, the limited-slip unit performs simi- wheel imbalance and cleaning the wheels will correct larly to a conventional differential. On slippery surfaces, the situation. however, the differential delivers more of the driving effort to the rear wheel having the better traction.
Page 353: Driving On Slippery Surfaces
352 STARTING AND OPERATING Care should be taken to avoid sudden accelerations when 2. Slow down if the road has standing water or puddles. both rear wheels are on a slippery surface. This could 3. Replace tires when tread wear indicators first become cause both rear wheels to spin, and allow the vehicle to visible.
Page 354: Flowing/Rising Water
STARTING AND OPERATING 353 Flowing/Rising Water CAUTION! • Always check the depth of the standing water WARNING! before driving through it. Never drive through Do not drive on or across a road or path where water standing water that is deeper than the bottom of is flowing and/or rising (as in storm run-off).
Page 355 354 STARTING AND OPERATING CAUTION! (Continued) WARNING! • Driving through standing water may cause dam- • Driving through standing water limits your vehi- age to your vehicle’s drivetrain components. Al- cle’s traction capabilities. Do not exceed 5 mph ways inspect your vehicle’s fluids (i.e., engine oil, (8 km/h) when driving through standing water.
Page 356: Driving Off-Road
STARTING AND OPERATING 355 NOTE: After off-road usage, particularly in sand or DRIVING OFF-ROAD Care should be taken when attempting to climb steep mud, inspect the underside of the vehicle for accumu- hills or driving diagonally across a hill or slope. If natural lated dirt at the propeller shaft, axles, U-joints, brake obstacles force you to travel diagonally up or down a hill, rotors and calipers.
Page 357: Winch Usage (Power Wagon Only) - If Equipped
356 STARTING AND OPERATING WINCH USAGE (POWER WAGON ONLY) — IF 2. Attach the hook to a suitable anchor point. EQUIPPED CAUTION! Things To Know Before Using Your Winch Be certain the anchor will withstand the load re- General Winch Information quired to tension the wire rope.
Page 358 STARTING AND OPERATING 357 Low Voltage Interrupt Winch Motor Thermal Protection Your winch is equipped with a device that will interrupt Your winch is equipped with a thermal protection device winch function if the vehicle charging system voltage in the motor. If the winch is operated for an excessive drops to a low level.
Page 359: Understanding The Features Of Your Winch
358 STARTING AND OPERATING Understanding The Features Of Your Winch Winch Components...
Page 360 STARTING AND OPERATING 359 1. Motor: The winch motor is powered by the vehicle 6. Clutch Lever: The clutch lever allows the winch drum charging system and features a thermal protection switch to be disconnected from the winch motor to allow the that automatically stops motor function in the power-in wire rope to be pulled from the winch by hand.
Page 361: Winch Accessories
360 STARTING AND OPERATING Winch Accessories Snatch/Block Pulley: Used properly, the multi-purpose The following accessories are necessary to attach the snatch block allows you to (1) winch to anchors, change direction of pull, and for safe increase the winch’s pulling winching.
Page 362: Operating Your Winch
STARTING AND OPERATING 361 Clevis/D-Shackles: Operating Your Winch D-Shackle is a safe means of WARNING! connecting the looped ends of cables, straps and snatch • Always use supplied hook strap to hold the hook blocks. The shackle’s pin is when spooling wire rope in or out. threaded to allow easy re- •...
Page 363 362 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Always keep hands and clothing clear of the wire • Never winch when there are less than five wraps rope, hook and fairlead opening during operation of wire rope around the winch drum. •...
Page 364 STARTING AND OPERATING 363 General Information Vehicle Recovery Using the Winch Practice using your winch before you get stuck. Some key CAUTION! points to remember when using your winch are: • Always Know Your Winch: Take the time to fully 1.
Page 365 364 STARTING AND OPERATING CAUTION! (Continued) • Always keep remote control lead clear of the drum, wire rope and rigging. • Inspect for cracks, pinches, frayed wires, or loose connections. Replace if damaged. • Be careful not to pull the Winch Cable Collar through the rollers.
Page 366 STARTING AND OPERATING 365 3. Disengage the clutch to allow free spooling of the 4. Free the winch hook and attach the hook strap. Free winch drum, rotate the clutch lever on the winch to the winch hook from its anchor point. Attach the hook disengage.
Page 367 366 STARTING AND OPERATING 5. Pull the wire to the anchor point. Pull out enough wire 6. Secure to the anchor point. Once you have established rope to reach your anchor point. Be sure to keep a certain your anchor point, secure the tree-trunk protector or amount of tension on the wire as it can become twisted choker-chain around the object.
Page 368 STARTING AND OPERATING 367 7. Attach the Clevis/D-shackle and Tree Trunk Protector. CAUTION! Attach the shackle to the two ends of the strap or chain and through the hook loop, being careful not to over Always be certain the anchor you select will with- tighten (tighten and back-off 1/2 turn).
Page 369 368 STARTING AND OPERATING NOTE: Always ensure the clutch is fully engaged or disengaged. 9. Connect the remote control to the winch control box, located behind the front bumper. Be careful not to let the remote control cord dangle in front of the winch. If you choose to control the winch from inside your vehicle, always pass the remote through a window to avoid pinching the cord in the door.
Page 370 STARTING AND OPERATING 369 12. Check wire rope. The wire rope should be neatly wound around the spooling drum. Improper winding can cause damage to the wire rope. 11. Check your anchor. Make sure all connections are secured and free of debris before continuing with the winching procedure.
Page 371 370 STARTING AND OPERATING 13. In certain situations you the vehicle and never near the wire rope or snatch may decide to throw a heavy block. Your situation may have other no people zones. blanket or similar object over the wire rope. A heavy blan- ket can absorb energy should the wire rope break.
Page 372 STARTING AND OPERATING 371 For additional assistance, the winched vehicle can be NOTE: • Avoid overheating the winch motor. For extended slowly driven while being pulled by the winch. Continue pulling until the vehicle is on stable ground. If you are winching, stop at reasonable intervals to allow the able to drive the vehicle, the winching operation is winch motor to cool down.
Page 373 372 STARTING AND OPERATING section of the rope and reposition it to the opposite end of the drum, which will free up space for continued winching. 16. Secure vehicle. Once recovery of the vehicle’s is complete, be sure to secure the vehicle’s brakes and put the transmission in PARK.
Page 374 STARTING AND OPERATING 373 How to spool under no load: Arrange the NOTE: remote control lead so it cannot be caught in the winch. Arrange the wire rope so it will not kink or tangle when spooled. Be sure any wire rope already on the spooling drum is wound tightly and evenly layered.
Page 375: Rigging Techniques
374 STARTING AND OPERATING Rigging Techniques How to Change the Pulling Direction Various winching situations will require application of other winching techniques. These could range from too little distance to achieve maximum pull using straight line rigging, simply increasing pulling power, or main- taining a straight-line pulling situation.
Page 376 STARTING AND OPERATING 375 will enable you to change your pulling direction while Double Line still allowing the wire rope to be at 90° to wind properly onto the spooling drum. Increasing Pulling Power In some cases, you may find yourself needing more pulling power.
Page 377: Power Steering
376 STARTING AND OPERATING vehicle’s frame/tow hook and run the wire rope through NOTE: • Increased noise levels at the end of the steering wheel a snatch block. Disengage the clutch and, using the snatch block, pull out enough wire to reach your anchor travel are considered normal and do not indicate that point.
Page 378: Power Steering Fluid Check
STARTING AND OPERATING 377 CAUTION! CAUTION! Prolonged operation of the steering system at the end Do not use chemical flushes in your power steering of the steering wheel travel will increase the steering system as the chemicals can damage your power fluid temperature and it should be avoided when steering components.
Page 379: Parking Brake
378 STARTING AND OPERATING surfaces. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. PARKING BRAKE The foot-operated parking brake is positioned below the lower left corner of the instrument panel. To release the parking brake, pull the parking brake release handle. NOTE: The “Brake Warning Light”...
Page 380: Brake System
STARTING AND OPERATING 379 When parking on a hill, turn the front wheels toward the WARNING! curb on a downhill grade and away from the curb on an • Always fully apply the parking brake when leav- uphill grade. ing your vehicle or it may roll and cause damage or The parking brake should always be applied whenever injury.
Page 381: 3500 Dual Rear Wheel Models Only
380 STARTING AND OPERATING 3500 Dual Rear Wheel Models Only Four-Wheel Anti-Lock Brake System The brake system power assist is provided by a hydro- WARNING! boost unit which shares fluid with the power steering system. You may experience some clicking or hissing The Four-Wheel Anti-Lock Brake System contains noises from the hydro-boost system during hard braking sophisticated electronic equipment.
Page 382 STARTING AND OPERATING 381 The system’s pump motor runs during an ABS stop to ABS Warning Light provide regulated hydraulic pressure. The pump motor The ABS includes an amber warning light. When the light makes a low humming noise during operation. This is is illuminated, the ABS is not functioning.
Page 383: Electronic Brake Control System
382 STARTING AND OPERATING control in various driving conditions, and are commonly WARNING! (Continued) referred to as ESP. • The ABS cannot prevent accidents, including Anti-Lock Brake System (ABS) those resulting from excessive speed in turns, The ABS aids the driver in maintaining vehicle control following another vehicle too closely, or hydro- under adverse braking conditions.
Page 384: Traction Control System (Tcs)
STARTING AND OPERATING 383 Traction Control System (TCS) WARNING! The TCS monitors the amount of wheel spin of each of • ABS cannot prevent the natural laws of physics the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s), and engine from acting on the vehicle, nor can it increase power is reduced to provide enhanced acceleration and braking or steering efficiency beyond that af-...
Page 385: Brake Assist System (Bas)
384 STARTING AND OPERATING Brake Assist System (BAS) WARNING! The BAS is designed to optimize the vehicle’s braking • The BAS cannot prevent the natural laws of phys- capability during emergency braking maneuvers. The BAS detects an emergency braking situation by sensing ics from acting on the vehicle, nor can it increase the rate and amount of brake application and then braking efficiency beyond that afforded by the...
Page 386: Hill Start Assist (Hsa)
STARTING AND OPERATING 385 Hill Start Assist (HSA) HSA Activation Criteria The HSA system is designed to assist the driver in The following criteria must be met in order for HSA to launching a vehicle on an incline. HSA will maintain the activate: level of brake pressure the driver inputs for a short •...
Page 387 386 STARTING AND OPERATING The system will only work if the intended direction of the when the TOW/HAUL switch is activated and compen- vehicle and vehicle gear match. For example, if the sates by releasing brake pressure at a slower rate while intended direction is forward up a hill and the vehicle is throttle is applied in order to prevent the vehicle from in DRIVE and the activation criteria are met, HSA will...
Page 388 STARTING AND OPERATING 387 3. With the engine running and the brake applied, rotate WARNING! (Continued) the steering wheel 180° counterclockwise from center. • HSA is not a parking brake. If you stop the vehicle 4. Press the ESP OFF switch four times within 20 sec- on a hill without putting the transmission in onds.
Page 389: Electronic Stability Program (Esp)
388 STARTING AND OPERATING EVIC Equipped Vehicles HSA is a Customer Programmable Feature on a EVIC equipped vehicle. If you wish to turn off the HSA feature, refer to “Customer Programmable Features/Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information. Electronic Stability Program (ESP) The ESP system enhances directional control and stability of the vehicle under various driving conditions.
Page 390 STARTING AND OPERATING 389 • Oversteer - when the vehicle is turning more than WARNING! appropriate for the steering wheel position. • ESP cannot prevent the natural laws of physics • Understeer - when the vehicle is turning less than from acting on the vehicle, nor can it increase the appropriate for the steering wheel position.
Page 391 390 STARTING AND OPERATING (2WD/4WD AUTO/4WD LOCK/4WD LOW/ driving situations. ESP should only be turned to “Partial NEUTRAL) transfer case. If you have a four-wheel drive Off” or “ESP Off” for specific reasons as noted below. vehicle, and want to determine which transfer case is on ESP Partial Off your vehicle and how to operate it, refer to “Four-Wheel This mode is entered by momentarily pressing the ESP...
Page 392 STARTING AND OPERATING 391 requiring ESP to be switched to the “Partial Off” mode is conditions. This mode is entered by pressing and holding overcome, turn ESP back on by momentarily pressing the the ESP OFF switch for five seconds when the vehicle is ESP OFF switch.
Page 393 392 STARTING AND OPERATING off at low vehicle speeds so that it will not interfere with WARNING! off-road driving but ESP function returns to provide the stability feature at speeds above 40 mph (64 km/h). The With the ESP switched off, the enhanced vehicle “ESP/TCS Indicator Light”...
Page 394: Trailer Sway Control (Tsc)
STARTING AND OPERATING 393 this light remains on after several ignition cycles and the Trailer Sway Control (TSC) vehicle has been driven several miles/kilometers at The TSC system uses sensors in the vehicle to recognize speeds greater than 30 mph (48 km/h), see your autho- an excessively swaying trailer and will take the appro- rized dealer as soon as possible to have the problem priate actions to attempt to stop the sway.
Page 395: Tire Safety Information
394 STARTING AND OPERATING TSC is only active in the default “ESP On” mode. TSC can TIRE SAFETY INFORMATION be disabled by pressing the ESP OFF switch and entering Tire Markings “ESP Partial Off” mode. It is not active in the “ESP Partial Off”...
Page 396 STARTING AND OPERATING 395 tires is the same as for P-Metric tires except for the NOTE: • P (Passenger) - Metric tire sizing is based on U.S. letters “LT” that are molded into the sidewall preced- design standards. P-Metric tires have the letter “P” ing the size designation.
Page 397 396 STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ..blank..= Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm)
Page 398 STARTING AND OPERATING 397 EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
Page 399: Tire Identification Number (Tin)
398 STARTING AND OPERATING Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall The TIN may be found on one or both sides of the tire, tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side.
Page 400: Tire Terminology And Definitions
STARTING AND OPERATING 399 Tire Terminology and Definitions Term Definition The vehicle B-Pillar is a structural member of the body located B-Pillar between the front and rear door (of a four-door vehicle) running from the sill to the roof. Cold Tire Pressure Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
Page 401: Tire Loading And Tire Pressure
400 STARTING AND OPERATING Tire Loading and Tire Pressure This placard tells you important information about the: Tire Placard Location 1) number of people that can be carried in the vehicle NOTE: The proper cold tire inflation pressure is listed 2) total weight your vehicle can carry on the driver’s side B-Pillar.
Page 402 STARTING AND OPERATING 401 NOTE: Under a maximum loaded vehicle condition, 2. Determine the combined weight of the driver and gross axle weight ratings (GAWRs) for the front and rear passengers that will be riding in your vehicle. axles must not be exceeded. For further information on 3.
Page 403 402 STARTING AND OPERATING 6. If your vehicle will be towing a trailer, load from your of your vehicle with varying seating configurations trailer will be transferred to your vehicle. Consult this and number and size of occupants. This table is for manual to determine how this reduces the available illustration purposes only and may not be accurate for cargo and luggage load capacity of your vehicle.
Page 404 STARTING AND OPERATING 403...
Page 405: Tires - General Information
404 STARTING AND OPERATING Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause accidents. recommended load capacity for your vehicle.
Page 406: Tire Inflation Pressures
STARTING AND OPERATING 405 Tire Inflation Pressures WARNING! (Continued) The proper cold tire inflation pressure is listed on the • Unequal tire pressures from one side of the ve- driver’s side “B” Pillar. hicle to the other can cause the vehicle to drift to Some vehicles may have Supplemental Tire Pressure the right or left.
Page 407 406 STARTING AND OPERATING Tire pressures change by approximately 1 psi (7 kPa) per CAUTION! 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in After inspecting or adjusting the tire pressure, al- the Winter.
Page 408: Tire Pressures For High Speed Operation
STARTING AND OPERATING 407 Tire Pressures for High Speed Operation Radial Ply Tires The manufacturer advocates driving at safe speeds WARNING! within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle...
Page 409: Tire Spinning
408 STARTING AND OPERATING original equipped tire on the front or rear axle of your Tire Spinning vehicle, but it is not. Installation of this limited-use spare When stuck in mud, sand, snow, or ice conditions, do not tire affects vehicle handling. Since it is not the same tire, spin your vehicle’s wheels faster than 30 mph (48 km/h) replace (or repair) the original tire and reinstall on the or for longer than 30 seconds continuously without...
Page 410: Tread Wear Indicators
STARTING AND OPERATING 409 These indicators are molded into the bottom of the tread Tread Wear Indicators Tread wear indicators are in the original equipment tires grooves. They will appear as bands when the tread depth to help you in determining when your tires should be becomes 1/16 in (2 mm).
Page 411: Replacement Tires
410 STARTING AND OPERATING wear and correct cold tire inflation pressure. The manu- WARNING! facturer strongly recommends that you use tires equiva- lent to the originals in size, quality and performance Tires and the spare tire should be replaced after six when replacement is needed.
Page 412: Supplemental Tire Pressure Information - If Equipped
STARTING AND OPERATING 411 WARNING! WARNING! (Continued) • Failure to equip your vehicle with tires having • Do not use a tire, wheel size or rating other than adequate speed capability can result in sudden tire that specified for your vehicle. Some combinations failure and loss of vehicle control.
Page 413: Tire Chains
412 STARTING AND OPERATING TIRE CHAINS CAUTION! (Continued) Use “Class S” chains, or other traction aids that meet SAE • Because of limited chain clearance between tires Type “S” specifications. and other suspension components, it is important Use “Class U” chains on 2500/3500 model trucks, or other that only chains in good condition are used.
Page 414 STARTING AND OPERATING 413 • The use of class “U” chains is permitted on the front CAUTION! (Continued) and rear of 4X4, 2500 model trucks with LT245/ • Observe the tire chain manufacturer’s instructions 70R17E tires. on method of installation, operating speed, and •...
Page 415: Snow Tires
414 STARTING AND OPERATING always be operated at the vehicle maximum capacity CAUTION! inflation pressures under any load condition. Do not use tire chains on 4x4 model trucks equipped While studded tires improve performance on ice, skid with P265/70R17, LT275/70R17, P275/60R20, tires. and traction capability on wet or dry surfaces may be There may not be adequate clearance for the chains poorer than that of non-studded tires.
Page 416 STARTING AND OPERATING 415 tires. Rotation will increase tread life, help to maintain mud, snow and wet traction levels and contribute to a smooth, quiet ride. Refer to “Maintenance Schedule” for the proper mainte- nance intervals. More frequent rotation is permissible if desired.
Page 417: Dual Rear Wheels
416 STARTING AND OPERATING Dual Rear Wheels CAUTION! 3500 Dual Rear Tires have only one approved direc- tion of rotation. This is to accommodate the asym- metrical design (tread pattern) of the On/Off-Road tire and the use of Outline White Letter (OWL) tires. •...
Page 418: Tire Pressure Monitor System (Tpms)
STARTING AND OPERATING 417 will also increase as the vehicle is driven - this is normal TIRE PRESSURE MONITOR SYSTEM (TPMS) The Tire Pressure Monitoring System (TPMS) will warn and there should be no adjustment for this increased the driver of a low tire pressure based on the vehicle pressure.
Page 419 418 STARTING AND OPERATING have been received. The vehicle may need to be driven CAUTION! for up to 20 minutes above 15 mph (25 km/h) to receive • The TPMS has been optimized for the original this information. equipment tires and wheels. TPMS pressures have As an example, assume your vehicle has a recommended been established for the tire size equipped on your cold tire inflation placard pressure (parked for more than...
Page 420: Tire Pressure Monitor System
STARTING AND OPERATING 419 • Seasonal temperature changes will affect tire pressure, NOTE: • The TPMS is not intended to replace normal tire care and the TPMS will monitor the actual tire pressure in and maintenance, nor to provide warning of a tire the tire.
Page 421 420 STARTING AND OPERATING Tire Pressure Monitoring Low Pressure Warnings switch is cycled, this sequence will repeat, providing the The Tire Pressure Monitoring Telltale Lamp will system fault still exists. A system fault can occur by any illuminate in the instrument cluster, and an au- of the following scenarios: dible chime will be activated when one or more of 1.
Page 422 STARTING AND OPERATING 421 1. This spare tire does not have a tire pressure monitor- 4. For each subsequent ignition switch cycle, a chime will ing sensor. Therefore, the TPMS will not monitor the tire sound and the “TPM Telltale Light” will flash on and off pressure in the spare tire.
Page 423: Tire Pressure Monitor System (Tpms) Tire Light Load Inflation Switch Description (2500 Models) - If Equipped
422 STARTING AND OPERATING Tire Pressure Monitor System (TPMS) Tire Light The TPMS tire light load inflation switch will allow the Load Inflation Switch Description (2500 Models) – driver to switch between the max load inflation pressure (cold) low pressure warning threshold and the light load If Equipped inflation pressure (cold) low pressure warning threshold WARNING!
Page 424 STARTING AND OPERATING 423 Tire Light Load Inflation Switch Operation – If Equipped • This vehicle may have different recommended tire pressure values between the front and rear tires as shown in both the Tire Loading Information Label and the Supplemental Tire Pressure Information Label. It is also equipped to be driven with tire pressures appro- priate to either a Light Load condition or the vehicle Max Load condition.
Page 425 424 STARTING AND OPERATING • The tire light load inflation switch will allow the driver to change between the max load inflation pressure (cold) low pressure warning threshold and the light load inflation pressure (cold) low pressure warning threshold depending on the vehicle’s load condition. Refer to the “Supplemental Tire Pressure Information”...
Page 426 STARTING AND OPERATING 425 Tire Pressure Information label. The Supplemental Tire the rear face of the driver door. Using an accurate tire Pressure Information label is located on the rear face of pressure gauge, re-check the tire pressures for the light the driver door.
Page 427: General Information
426 STARTING AND OPERATING the max load inflation pressure (cold) values to switch General Information the TPMS system to the max load inflation pressure This device complies with part 15 of the FCC rules and (cold) low pressure warning threshold. If after pressing RSS 210 of Industry Canada.
Page 428: Fuel Requirements
STARTING AND OPERATING 427 for optimum performance. The use of premium gasoline FUEL REQUIREMENTS is not recommended, as it will not provide any benefit 3.7L and 4.7L Engine over regular gasoline in these engines. All engines (except 5.7L engines) are de- signed to meet all emissions regulations Light spark knock at low engine speeds is not harmful to and provide excellent fuel economy and...
Page 429: Reformulated Gasoline
428 STARTING AND OPERATING Reformulated Gasoline CAUTION! Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline.” Do not use gasoline containing Methanol or E85 Reformulated gasolines contain oxygenates and are spe- Ethanol. Use of these blends may result in starting cifically blended to reduce vehicle emissions and im- and drivability problems and may damage critical prove air quality.
Page 430: Mmt In Gasoline
STARTING AND OPERATING 429 • OBD II “Malfunction Indicator Light” on blended with MMT provides no performance advantage beyond gasoline of the same octane number without • poor engine performance MMT. Gasoline blended with MMT reduces spark plug • poor cold start and cold drivability life and reduces emissions system performance in some vehicles.
Page 431: Fuel System Cautions
430 STARTING AND OPERATING Fuel System Cautions CAUTION! (Continued) • The use of fuel additives, which are now being CAUTION! sold as octane enhancers are not recommended. Follow these guidelines to maintain your vehicle’s Most of these products contain high concentra- performance: tions of methanol.
Page 432: Carbon Monoxide Warnings
STARTING AND OPERATING 431 Carbon Monoxide Warnings WARNING! (Continued) • Guard against carbon monoxide with proper WARNING! maintenance. Have the exhaust system inspected Carbon monoxide (CO) in exhaust gases is deadly. every time the vehicle is raised. Have any abnor- Follow the precautions below to prevent carbon mal conditions repaired promptly.
Page 433: Flexible Fuel (4.7L Engine Only) - If Equipped
432 STARTING AND OPERATING FLEXIBLE FUEL (4.7L ENGINE ONLY) — IF EQUIPPED E85 General Information The information in this section is for Flexible Fuel Ve- hicles (FFV) only. These vehicles can be identified by the unique fuel filler door label that states Ethanol (E85) or Unleaded Gasoline Only.
Page 434: Ethanol Fuel (E85)
STARTING AND OPERATING 433 WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smok- ing materials lit in or near the vehicle when remov- ing the fuel filler tube cap (gas cap) or filling the tank.
Page 435: Selection Of Engine Oil For Flexible Fuel Vehicles (E85) And Gasoline Vehicles
434 STARTING AND OPERATING • you drive the vehicle immediately after refueling for at Selection Of Engine Oil For Flexible Fuel Vehicles least 5 miles (8 km) (E85) and Gasoline Vehicles FFV vehicles operated on E85 require specially formu- Observing these precautions will avoid possible hard lated engine oils.
Page 436: Cruising Range
STARTING AND OPERATING 435 NOTE: Use of the engine block heater (if equipped) is CAUTION! beneficial for E85 startability when the ambient tempera- ture is less than 32°F (0°C). Replacing fuel system components with non-ethanol compatible components can damage your vehicle. Cruising Range Because E85 fuel contains less energy per gallon/liter Maintenance...
Page 437: Adding Fuel
436 STARTING AND OPERATING ADDING FUEL NOTE: When removing the fuel filler cap, lay the cap The fuel filler cap (gas cap) is located behind the fuel tether in the hook, located on the fuel filler door. filler door, on the left side of the vehicle. Open the fuel CAUTION! door and remove the fuel cap by turning it counter- clockwise.
Page 438: Loose Fuel Filler Cap Message
STARTING AND OPERATING 437 • When the fuel nozzle “clicks” or shuts off, the fuel WARNING! tank is full. • Never have any smoking materials lit in or near Loose Fuel Filler Cap Message the vehicle when the gas cap is removed or the If the vehicles diagnostic system determines that the fuel tank filled.
Page 439: Vehicle Loading
438 STARTING AND OPERATING VEHICLE LOADING Payload The payload of a vehicle is defined as the allowable load Certification Label weight a truck can carry, including the weight of the As required by National Highway Traffic Safety Admin- driver, all passengers, options and cargo. istration regulations, your vehicle has a certification label affixed to the driver’s side door or pillar.
Page 440 STARTING AND OPERATING 439 The entire vehicle should first be weighed on a commer- Rim Size This is the rim size that is appropriate for the tire size cial scale to insure that the GVWR has not been exceeded. listed. The weight on the front and rear of the vehicle should then be determined separately to be sure that the load is Inflation Pressure...
Page 441: Trailer Towing
440 STARTING AND OPERATING Common Towing Definitions CAUTION! The following trailer towing related definitions will assist you in understanding the following information: Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR. If you do, Gross Vehicle Weight Rating (GVWR) parts on your vehicle can break, or it can change the The GVWR is the total allowable weight of your vehicle.
Page 442 STARTING AND OPERATING 441 Gross Combination Weight Rating (GCWR) Tongue Weight (TW) The GCWR is the total permissible weight of your vehicle The tongue weight is the downward force exerted on the and trailer when weighed in combination. hitch ball by the trailer. In most cases it should not be less than 10% or more than 15% of the trailer load.
Page 443 442 STARTING AND OPERATING hitches are the most popular on the market today and WARNING! they’re commonly used to tow small- and medium-sized • An improperly adjusted weight distributing hitch trailers. system may reduce handling, stability and braking Weight-Distributing Hitch performance and could result in an accident.
Page 444 STARTING AND OPERATING 443 EXAMPLE — Without Weight-Distributing Hitch EXAMPLE — With Weight-Distributing Hitch (Correct) (Incorrect)
Page 445: Trailer Hitch Classification
444 STARTING AND OPERATING Gooseneck Hitch The gooseneck hitch employs a pivoted coupling arm which attaches to a ball mounted in the bed of a pickup truck. The coupling arm connects to the hitch mounted over the rear axle in the truck bed. Trailer Hitch Classification The rear bumper is intended to tow trailers up to 5,000 lbs (2 268 kg) without added equipment or alter-...
Page 446: Trailer Towing Weights (Maximum Trailer Weight Ratings)
• http:// www.dodge.com. Class III - Heavy Duty 5,000 lbs (2268 kg) Class IV - Extra 10,000 lbs (4540 kg) • http:// www.dodge.ca (Canada). Heavy Duty Trailer and Tongue Weight Fifth Wheel/ Greater than 10,000 lbs Always load a trailer with 60% to 65% of the weight in...
Page 447 446 STARTING AND OPERATING • The weight of any other type of cargo or equipment Never exceed the maximum tongue weight stamped on your bumper or trailer hitch. put in or on your vehicle • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle.
Page 448: Towing Requirements
STARTING AND OPERATING 447 Towing Requirements WARNING! To promote proper break-in of your new vehicle drive- train components the following guidelines are recom- Improper towing can lead to an injury accident. mended: Follow these guidelines to make your trailer towing as safe as possible: CAUTION! •...
Page 449 448 STARTING AND OPERATING 1. GVWR WARNING! (Continued) 2. GTW • Safety chains must always be used between your vehicle and trailer. Always connect the chains to 3. GAWR the frame or hook retainers of the vehicle hitch. 4. Tongue weight rating for the trailer hitch utilized (This Cross the chains under the trailer tongue and requirement may limit the ability to always achieve the allow enough slack for turning corners.
Page 450 STARTING AND OPERATING 449 • Check for signs of tire wear or visible tire damage actuated brakes. When towing a trailer equipped with before towing a trailer. Refer to “Tires – General a hydraulic surge actuated brake system, an electronic Information”...
Page 451 450 STARTING AND OPERATING WARNING! • Do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident.
Page 452 STARTING AND OPERATING 451 This display may also be used to display diagnostic The trailer and the vehicle’s brake lamps will come on information, if needed. when either vehicle braking or manual trailer brakes are applied. • SC — Short Circuit to Ground Trailer Brake Status Indicator Light •...
Page 453 452 STARTING AND OPERATING GAIN setting can be increased to a maximum of 10 or 3. When a trailer with electric brakes is plugged in, the decreased to a minimum of 0 (no trailer braking). GAIN setting will illuminate. GAIN 4.
Page 454 STARTING AND OPERATING 453 EVIC Display Messages WARNING! The trailer brake control interacts with the Electronic Vehicle Information Center (EVIC). Display messages, Connecting a trailer that is not compatible with the along with a single chime, will be displayed when a ITBM system may result in reduced or complete loss malfunction is determined in the trailer connection, of trailer braking.
Page 455 454 STARTING AND OPERATING The Trailer Tow Package will include a four and seven- pin wiring harness. Use a factory approved trailer har- ness and connector. NOTE: Do not cut or splice wiring into the vehicle’s wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector.
Page 456: Towing Tips
STARTING AND OPERATING 455 WARNING! Any work done to the vehicle’s electrical system or wiring should be performed by a qualified automo- tive technician. If done improperly it may cause damage to the electrical system wiring and could result in serious or fatal injury. Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer up in an area away from heavy...
Page 457 456 STARTING AND OPERATING NOTE: Using “TOW/HAUL” mode or a lower gear Electronic Speed Control – If Equipped range while operating the vehicle under heavy operating − Do not use in hilly terrain or with heavy loads. conditions will improve performance and extend trans- mission life by reducing excessive shifting and heat build −...
Page 458: Snowplow
STARTING AND OPERATING 457 − Air Conditioning CAUTION! Turn off temporarily. Using this vehicle for snowplow applications can SNOWPLOW cause damage to the vehicle. 1500 Models Only WARNING! NOTE: Do not use this model vehicle for snowplow applications. Attaching a snowplow to this vehicle could adversely affect performance of the airbag system in an acci- WARNING! dent.
Page 459 458 STARTING AND OPERATING Dodge Body Builders Guide. See your authorized dealer, Before Plowing installer or snowplow manufacturer for this information. • Check the hydraulic system for leaks and proper fluid There are unique electrical systems that must be con- level.
Page 460 STARTING AND OPERATING 459 2. The total GVWR or the Front GAWR or the Rear if necessary at the beginning and end of the snowplow GAWR should never be exceeded. season. This will help prevent uneven tire wear. 3. Cargo capacity will be reduced by the addition of The blade should be lowered whenever the vehicle is options or passengers, etc.
Page 461 460 STARTING AND OPERATING Operating Tips General Maintenance Under ideal snow plowing conditions, 20 mph (32 km/h) Snowplows should be maintained in accordance with the should be maximum operating speed. The operator plow manufacturer’s instructions. should be familiar with the area and surface to be Keep all snowplow electrical connections and battery cleaned.
Page 462: Recreational Towing (Behind Motorhome, Etc.)
STARTING AND OPERATING 461 • Do not shift the transmission unless the engine has Recreational Towing – Four-Wheel Drive Models returned to idle and wheels have stopped. Make a CAUTION! practice of stepping on the brake pedal before shifting the transmission. Failure to follow these requirements can cause severe damage to the transmission and/or transfer case.
Page 463 462 STARTING AND OPERATING Recreational Towing Procedure (Manual Shift CAUTION! Transfer Case) – If Equipped Use the following procedure to prepare your vehicle for It is necessary to follow these steps to be certain that recreational towing: the transfer case is fully in NEUTRAL before recre- ational towing to prevent damage to internal parts.
Page 464 STARTING AND OPERATING 463 9. Repeat steps 7 and 8 with the transmission in DRIVE. Returning to Normal Operation – Manual Shift Transfer Case 10. Turn OFF the engine and place the ignition switch in Use the following procedure to prepare your vehicle for the OFF position.
Page 465 464 STARTING AND OPERATING WARNING! CAUTION! • Do not use a bumper-mounted clamp-on tow bar You or others could be injured if you leave the vehicle unattended with the transfer case in the on your vehicle. The bumper face bar will be NEUTRAL position without first fully engaging the damaged.
Page 466 STARTING AND OPERATING 465 Recreational Towing Procedure (Electronic Shift CAUTION! Transfer Case) – If Equipped Use the following procedure to prepare your vehicle for It is necessary to follow these steps to be certain that recreational towing: the transfer case is fully in NEUTRAL before recre- ational towing to prevent damage to internal parts.
Page 467 466 STARTING AND OPERATING • Steps 1 through 5 are requirements that must be met 8. Start the engine. prior to pressing the NEUTRAL button, and must 9. Shift the transmission into REVERSE. continue to be met until the four seconds elapses and 10.
Page 468 STARTING AND OPERATING 467 5. Shift the transmission into NEUTRAL. CAUTION! 6. Press the transfer case switch NEUTRAL button for Damage to the transmission may occur if the trans- one second. mission is shifted into PARK with the transfer case in 7.
Page 469 468 STARTING AND OPERATING of the mode position indicator lights will flash con- WARNING! tinuously until all requirements are met or until the NEUTRAL button is released. You or others could be injured if you leave the vehicle unattended with the transfer case in the •...
Page 470: Equipment Identification Plate
STARTING AND OPERATING 469 EQUIPMENT IDENTIFICATION PLATE CAUTION! The equipment Identification Plate is located on the hood • Do not use a bumper-mounted clamp-on tow bar inner surface. on your vehicle. The bumper face bar will be The following information about your vehicle is dis- damaged.
Page 472: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....472 Hoisting ......491 Jacking And Tire Changing .
Page 473: Hazard Warning Flasher
472 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER JACKING AND TIRE CHANGING The Hazard Warning flasher switch is located on the WARNING! upper switch bank just below the radio. • Being under a jacked-up vehicle is dangerous. The Press the switch to turn on the Hazard Warning flasher.
Page 474: Jack Location
WHAT TO DO IN EMERGENCIES 473 Jack Location The jack and jack tools are stored under the front passenger seat. Removal To access the jack and jack tools you must remove the plastic access cover, located on the side of the seat. To remove the cover, pull the front part of the cover (closest to the front of the seat) toward you to release a locking tab.
Page 475 474 WHAT TO DO IN EMERGENCIES Remove the jack and tools by removing the wing bolt and sliding the assembly from under the seat. Jack and Tools (2500/3500 Series) Jack and Tools (1500 Series)
Page 476 WHAT TO DO IN EMERGENCIES 475 WARNING! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience abrupt stopping, rapid accelera- tion or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury.
Page 477 476 WHAT TO DO IN EMERGENCIES 3. Fold the flap and roll the jack tool kit into a cylindrical package (in direction of arrows) and tie to the jack using the tie straps. Tying Bag to Jack with Straps Folding Flap and Rolling Bag...
Page 478 WHAT TO DO IN EMERGENCIES 477 Jack and Tools Tied Jack and Tools (1500 Series) 4. Place the jack and tools in the storage position holding the jack by the jack turn-screw, slip the jack and tools under the seat so that the bottom slot engages into the fastener on the floor, and then secure to the floor pan using the wing bolt.
Page 479: Removing The Spare Tire
478 WHAT TO DO IN EMERGENCIES Removing The Spare Tire Remove the spare tire before attempting to jack up the truck. Attach the wheel wrench to the jack extension tube. Insert the tube through the access hole between the lower tailgate and the top of the bumper and into the winch mechanism tube.
Page 480: Preparations
WHAT TO DO IN EMERGENCIES 479 NOTE: The winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch. Preparations 1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas.
Page 481: Instructions
480 WHAT TO DO IN EMERGENCIES 4. Turn the ignition OFF. Instructions 5. Turn on the Hazard Warning flasher. WARNING! 6. Block both the front and rear of the Carefully follow these tire changing warnings to wheel diagonally opposite the jacking help prevent personal injury or damage to your position.
Page 482 WHAT TO DO IN EMERGENCIES 481 WARNING! (Continued) • Do not let anyone sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack. • Only use the jack in the positions indicated and Jack Warning Label for lifting this vehicle during a tire change.
Page 483 482 WHAT TO DO IN EMERGENCIES • 1500 Series Trucks When changing a front wheel, place the scissors jack under the rear portion of the lower control arm as shown below. 4X4 Jacking Location Operate the jack using the jack drive tube and the wheel wrench.
Page 484 WHAT TO DO IN EMERGENCIES 483 For 4x2 and 4x4 trucks, when changing a rear wheel, Connect the jack tube extension and wheel wrench. assemble the jack drive tube to the jack and connect the CAUTION! drive tube to the extension tube. Place the jack under the axle between the wheel and the shock bracket with the Before raising the wheel off the ground, make sure drive tubes extending to the rear.
Page 485 484 WHAT TO DO IN EMERGENCIES • 2500/3500 Series Trucks Operate the jack using the jack drive tube and the wheel For 2500/3500 4x2 series trucks, when changing a front wrench. The tube extension, may be used, but is not wheel, place the bottle jack under the frame rail behind required.
Page 486 WHAT TO DO IN EMERGENCIES 485 4x4 Jacking Location Rear Jacking Location (All) For 4x2 and 4x4 trucks, when changing a rear wheel, Connect the jack tube extension and wheel wrench. assemble the jack drive tube to the jack and connect the drive tube to the extension tube.
Page 487 486 WHAT TO DO IN EMERGENCIES 5. Remove the wheel nuts and pull the wheel off. On CAUTION! single rear-wheel (SRW) trucks, install the spare wheel and wheel nuts with the cone shaped end of the wheel Before raising the wheel off the ground, make sure nuts toward the wheel.
Page 488: Hub Caps/Wheel Covers - If Equipped
WHAT TO DO IN EMERGENCIES 487 Hub Caps/Wheel Covers — If Equipped WARNING! The hub caps must be removed before raising the vehicle off the ground. A loose tire or jack thrown forward in a collision or hard stop could injure someone in the vehicle. Al- For 2500/3500 single rear-wheel (SRW) models, use the ways stow the jack parts and the extra tire and wheel blade on the end of the lug wrench to pry the hub cap off.
Page 489: Wheel Nuts
488 WHAT TO DO IN EMERGENCIES Wheel Nuts CAUTION! All wheel nuts should be tightened occasionally to elimi- • Use a back-and-forth motion to remove the hub cap. nate the possibility of wheel studs being sheared or the bolt holes in the wheels becoming elongated. This is especially Do not use a twisting motion when removing the important during the first few hundred miles/kilometers hub cap, damage to the hub cap finish may occur.
Page 490 WHAT TO DO IN EMERGENCIES 489 Slots in the wheels will assist in properly orienting the 8-Stud — Dual Rear Wheels Dual wheels are flat-mounted and center-piloted. The lug inner and outer wheels. Align these slots when assem- nuts are a two-piece assembly. When the tires are being bling the wheels for best access to the tire valve on the rotated or replaced, clean these lug nuts and add two inner wheel.
Page 491: To Stow The Flat Or Spare
490 WHAT TO DO IN EMERGENCIES These dual rear wheels should be tightened as follows: second time to verify that specific torque has been achieved. Retighten to specifications at 100 miles (160 km) and after 500 miles (800 km). It is recommended that wheel stud nuts be kept torqued to specifications at all times.
Page 492: Hoisting
WHAT TO DO IN EMERGENCIES 491 HOISTING WARNING! A conventional floor jack may be used at the jacking locations. Refer to the graphics that show jacking loca- A loose tire thrown forward in a collision or hard tions. However, a floor jack or frame hoist must never be stop could injure the occupants in the vehicle.
Page 493: Preparations For Jump-Start
492 WHAT TO DO IN EMERGENCIES NOTE: When using a portable battery booster pack Preparations for Jump-Start follow the manufacturer’s operating instructions and The battery in your vehicle is located in the front of the precautions. engine compartment, behind the left headlight assembly. NOTE: The positive battery post is covered with a CAUTION! protective cap.
Page 494: Jump-Starting Procedure
WHAT TO DO IN EMERGENCIES 493 3. If using a another vehicle to jump-start the battery, WARNING! park the vehicle within the jumper cables reach, set the • Take care to avoid the radiator cooling fan when- parking brake and make sure the ignition is OFF. ever the hood is raised.
Page 495 494 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! Failure to follow these procedures could result in Do not connect the cable to the negative post (-) of the damage to the charging system of the booster vehicle discharged battery. The resulting electrical spark or the discharged vehicle.
Page 496: Freeing A Stuck Vehicle
WHAT TO DO IN EMERGENCIES 495 8. Disconnect the opposite end of the positive (+) jumper FREEING A STUCK VEHICLE cable from the positive (+) post of the booster battery. If the vehicle becomes stuck in snow, sand or mud, it can often be moved by a rocking motion.
Page 497: Emergency Tow Hooks - If Equipped
496 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! • When “rocking” a stuck vehicle by moving be- Fast spinning tires can be dangerous. Forces gener- tween 1st and REVERSE, do not spin the wheels ated by excessive wheel speeds may cause damage, or faster than 15 mph (24 km/h), or drivetrain damage even failure, of the axle and tires.
Page 498: Towing A Disabled Vehicle
WHAT TO DO IN EMERGENCIES 497 equipment designed for the purpose, following equip- WARNING! ment manufacturer’s instructions. Use of safety chains is • Chains are not recommended for freeing a stuck mandatory. Attach a tow bar or other towing device to the main structural members of the vehicle, not to vehicle.
Page 499: Two-Wheel Drive Vehicles
498 WHAT TO DO IN EMERGENCIES CAUTION! CAUTION! Failure to follow these towing methods could result Towing faster than 30 mph (50 km/h) or for more than in damage to the transfer case. Such damage is not 15 miles (25 km) can cause severe damage to the covered by the New Vehicle Limited Warranty.
Page 500 MAINTAINING YOUR VEHICLE CONTENTS Engine Compartment — 3.7L ... . . 502 Maintenance Procedures ....508 Engine Compartment —...
Page 501 500 MAINTAINING YOUR VEHICLE Windshield Wiper Blades ....516 Replacement Bulbs ....542 Adding Washer Fluid .
Page 502 MAINTAINING YOUR VEHICLE 501 Fluid Capacities ..... . 552 Engine ......554 Fluids, Lubricants And Genuine Parts .
Page 503: Engine Compartment - 3.7L
502 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 3.7L 1 — Air Cleaner Filter 7 — Washer Fluid Reservoir 2 — Automatic Transmission Dipstick (If Equipped) 8 — Power Steering Fluid Reservoir 3 — Engine Oil Dipstick 9 — Engine Oil Fill 4 —...
Page 504: Engine Compartment - 4.7L
MAINTAINING YOUR VEHICLE 503 ENGINE COMPARTMENT — 4.7L 1 — Air Cleaner Filter 7 — Washer Fluid Reservoir 2 — Automatic Transmission Dipstick 8 — Power Steering Fluid Reservoir 3 — Engine Oil Dipstick 9 — Engine Oil Fill 4 — Brake Fluid Reservoir 10 —...
Page 505: Engine Compartment - 5.7L
504 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 5.7L 1 — Air Cleaner Filter 7 — Washer Fluid Reservoir 2 — Automatic Transmission Dipstick 8 — Integrated Power Module 3 — Engine Oil Fill 9 — Power Steering Fluid Reservoir 4 — Engine Oil Dipstick 10 —...
Page 506: Onboard Diagnostic System (Obd Ii)
MAINTAINING YOUR VEHICLE 505 ONBOARD DIAGNOSTIC SYSTEM (OBD II) CAUTION! Your vehicle is equipped with a sophisticated onboard • Prolonged driving with the MIL on could cause diagnostic system called OBDII. This system monitors the performance of the emissions, engine, and automatic further damage to the emission control system.
Page 507: Emissions Inspection And Maintenance Programs
506 MAINTAINING YOUR VEHICLE will appear the next time the vehicle is started. This serviced, recently had a dead battery or a battery replace- might indicate a damaged cap. If the problem is detected ment. If the OBD II system should be determined not twice in a row, the system will turn on the MIL.
Page 508: Replacement Parts
MAINTAINING YOUR VEHICLE 507 4. Approximately 15 seconds later, one of two things will Regardless of whether your vehicle’s OBD II system is happen: ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced a.
Page 509: Maintenance Procedures
508 MAINTAINING YOUR VEHICLE your vehicle. Refer to these manuals before attempting MAINTENANCE PROCEDURES any procedure yourself. The pages that follow contain the required maintenance services determined by the engineers who designed your NOTE: Intentional tampering with emissions control vehicle. systems may void your warranty and could result in civil penalties being assessed against you.
Page 510: Engine Oil
MAINTAINING YOUR VEHICLE 509 The best time to check the engine oil level is about five CAUTION! (Continued) minutes after a fully warmed up engine is shut off. • Your vehicle has been built with improved fluids Checking the oil while the vehicle is on level ground will that protect the performance and durability of improve the accuracy of the oil level readings.
Page 511 510 MAINTAINING YOUR VEHICLE NOTE: Under no circumstances should oil change CAUTION! intervals exceed 6,000 miles (10 000 km) or six months, whichever occurs first. Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is Engine Oil Selection not covered by the New Vehicle Limited Warranty.
Page 512: Engine Oil Filter
MAINTAINING YOUR VEHICLE 511 Lubricants which do not have both the engine oil certi- Disposing of Used Engine Oil and Oil Filters fication mark and the correct SAE viscosity grade num- Care should be taken in disposing of used engine oil and ber should not be used.
Page 513: Engine Air Cleaner Filter
512 MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter used to assure most efficient service. MOPAR engine air Refer to “Maintenance Schedule” for further information. cleaner filters are a high quality filter and are recommended. WARNING! Maintenance-Free Battery The top of the maintenance-free battery is permanently The air induction system (air cleaner, hoses, etc.) can sealed.
Page 514 MAINTAINING YOUR VEHICLE 513 WARNING! (Continued) CAUTION! • Battery gas is flammable and explosive. Keep • It is essential when replacing the cables on the flame or sparks away from the battery. Do not use battery that the positive cable is attached to the a booster battery or any other booster source with positive post and the negative cable is attached to an output greater than 12 volts.
Page 515: Air Conditioner Maintenance
514 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance WARNING! For best possible performance, your air conditioner • Use only refrigerants and compressor lubricants should be checked and serviced by an authorized dealer at the start of each warm season. This service should approved by the manufacturer for your air condi- include cleaning of the condenser fins and a performance tioning system.
Page 516: Front Prop Shaft Lubrication - 2500/3500
MAINTAINING YOUR VEHICLE 515 tailgate, sliding doors and hood hinges, should be lubri- Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluoro- cated periodically with a lithium based grease, such as carbon (HFC) that is endorsed by the Environmental MOPAR Spray White Lube or equivalent, to assure Protection Agency (EPA) and is an ozone-saving product.
Page 517: Windshield Wiper Blades
516 MAINTAINING YOUR VEHICLE Windshield Wiper Blades present please proceed to clean wiper blades with humid Clean the rubber edges of the wiper blades and the cloth removing any debris that may be affecting its windshield periodically with a sponge or soft cloth and a function.
Page 518: Exhaust System
MAINTAINING YOUR VEHICLE 517 Whenever a change is noticed in the sound of the exhaust WARNING! system, when exhaust fumes can be detected inside the vehicle or when the underside or rear of the vehicle is Commercially available windshield washer solvents damaged, have a competent mechanic inspect the com- are flammable.
Page 519 518 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- WARNING! verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure Exhaust gases can injure or kill. They contain carbon proper catalyst operation and prevent possible catalyst monoxide (CO) which is colorless and odorless.
Page 520 MAINTAINING YOUR VEHICLE 519 NOTE: Intentional tampering with emissions control To minimize the possibility of catalyst damage: systems can result in civil penalties being assessed • Do not shut off the engine or interrupt the ignition against you. when the transmission is in gear and the vehicle is in motion.
Page 521: Cooling System
520 MAINTAINING YOUR VEHICLE Cooling System Check the coolant recovery bottle tubing for brittle rub- ber, cracking, tears, cuts and tightness of the connection WARNING! at the bottle and radiator. Inspect the entire system for leaks. You or others can be badly burned by hot coolant or With the engine at normal operating temperature (but steam from your radiator.
Page 522 MAINTAINING YOUR VEHICLE 521 Refer to “Maintenance Schedule” for further information. CAUTION! (Continued) Selection Of Coolant • Do not use water alone or alcohol-based engine Use only the manufacturer’s recommended engine cool- coolant (antifreeze) products. Do not use addi- ant (antifreeze). Refer to “Fluids, Lubricants, and Genu- tional rust inhibitors or antirust products, as they ine Parts”...
Page 523 522 MAINTAINING YOUR VEHICLE Please review these recommendations for using Hybrid Please note that it is the owner’s responsibility to main- Organic Additive Technology (HOAT) engine coolant tain the proper level of protection against freezing ac- (antifreeze). cording to the temperatures occurring in the area where the vehicle is operated.
Page 524 MAINTAINING YOUR VEHICLE 523 engine coolant (antifreeze) in open containers or allow it WARNING! to remain in puddles on the ground. If ingested by a child • The warning words “DO NOT OPEN HOT” on the or pet, seek emergency assistance immediately. Clean up any ground spills immediately.
Page 525 524 MAINTAINING YOUR VEHICLE When additional engine coolant (antifreeze) is needed to coolant (antifreeze) needs to be added, contents of maintain the proper level, it should be added to the coolant recovery bottle must also be protected against coolant bottle. Do not overfill. freezing.
Page 526: Brake System
MAINTAINING YOUR VEHICLE 525 • Do not change the thermostat for Summer or Winter Brake Fluid Level Check operation. If replacement is ever necessary, install The fluid level of the master cylinder should be checked ONLY the correct type thermostat. Other designs may when performing under the hood service or immediately result in unsatisfactory engine coolant (antifreeze) if the brake system warning lamp indicates system...
Page 527 526 MAINTAINING YOUR VEHICLE WARNING! WARNING! (Continued) • To avoid contamination from foreign matter or • Use only manufacturer’s recommended brake moisture, use only new brake fluid or fluid that fluid. Refer to “Fluids, Lubricants, and Genuine has been in a tightly closed container. Keep the Parts”...
Page 528: Rear Axle And 4X4 Front Driving Axle Fluid Level
MAINTAINING YOUR VEHICLE 527 axles. The fluid level should be 5/8 in (16 mm) below the WARNING! (Continued) fill hole on 9 1/4 in manufacturer’s rear axles. • Do not allow petroleum based fluid to contami- For all 2500/3500 Model axles, the fluid level should be nate the brake fluid.
Page 529: Transfer Case
528 MAINTAINING YOUR VEHICLE Limited-Slip Differentials This vehicle requires that Fluid Level Check 4 oz. (118 ml) MOPAR Limited Slip Additive or equiva- This fluid level can be checked by removing the filler lent be added to the gear lubricant. Refer to “Fluids, plug.
Page 530 MAINTAINING YOUR VEHICLE 529 should not be tampered with. Your authorized dealer has CAUTION! the proper tools to ensure that the fluid level is set • Do not use chemical flushes in your transmission properly. The fluid level should be checked when the engine is fully warmed up and the fluid in the transmis- as the chemicals can damage your transmission sion is at normal operating temperature.
Page 531 530 MAINTAINING YOUR VEHICLE 2. The vehicle must be on level ground. NOTE: If it is necessary to check the transmission below the operating temperature, the fluid level should be 3. Fully apply the parking brake and press the brake between the two “COLD”...
Page 532: Appearance Care And Protection From Corrosion
MAINTAINING YOUR VEHICLE 531 To prevent dirt and water from entering the transmission Special Additives after checking or replenishing fluid, make certain that the Automatic Transmission Fluid (ATF) is an engineered dipstick cap is properly reseated. It is normal for the product and its performance may be impaired by supple- dipstick cap to spring back slightly from its fully seated mental additives.
Page 533 532 MAINTAINING YOUR VEHICLE hot or cold weather and other extreme conditions will Washing have an adverse affect on paint, metal trim, and under- • Wash your vehicle regularly. Always wash your ve- body protection. hicle in the shade using MOPAR Car Wash or equiva- The following maintenance recommendations will enable lent, or a mild car wash soap and rinse the panels you to obtain maximum benefit from the corrosion...
Page 534 MAINTAINING YOUR VEHICLE 533 • If your vehicle is damaged due to an accident or CAUTION! similar cause which destroys the paint and protective coating, have your vehicle repaired as soon as pos- Do not use abrasive or strong cleaning materials such sible.
Page 535 534 MAINTAINING YOUR VEHICLE • For tough stains, apply MOPAR heavy soil and/or excessive brake dust, use MOPAR Total Clean or Wheel Cleaner or equivalent or select a nonabrasive, equivalent, or a mild soap solution to a clean, damp non-acidic cleaner. Do not use scouring pads, steel wool, cloth and remove stain.
Page 536 MAINTAINING YOUR VEHICLE 535 Your leather upholstery can be best preserved by regular Cleaning Headlights cleaning with a damp soft cloth. Small particles of dirt Your vehicle is equipped with plastic headlights and fog can act as an abrasive and damage the leather upholstery lights (if equipped) that are lighter and less susceptible to and should be removed promptly with a damp cloth.
Page 537: Fuses
536 MAINTAINING YOUR VEHICLE cleaner. Use caution when cleaning the inside rear win- Seat Belt Maintenance dow equipped with electric defrosters or the right rear Do not bleach, dye or clean the belts with chemical quarter window equipped with the radio antenna. Do solvents or abrasive cleaners.
Page 538 MAINTAINING YOUR VEHICLE 537 cover, otherwise the cavity number of each fuse is Cavity Cartridge Mini Description stamped on the inside cover that corresponds to the Fuse Fuse following chart. 30 Amp Bat – Presafe #1 Pink 30 Amp Bat – Trailer Tow Pink Main 25 Amp...
Page 539 538 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Description Cavity Cartridge Mini Description Fuse Fuse Fuse Fuse 30 Amp Bat – Plg/Electric 25 Amp Bat – Sunroof/ Pink Brake Natural Skylight 40 Amp Bat – L/Bar/Off-Road 25 Amp TCM/Trans Range Green Natural 30 Amp Bat –...
Page 540 MAINTAINING YOUR VEHICLE 539 Cavity Cartridge Mini Description Cavity Cartridge Mini Description Fuse Fuse Fuse Fuse 10 Amp Bat – J1962 Diag/ 15 Amp Bat – NGC/EATX/ Mirrors Blue 10 Amp Bat – Ign Sw, WIN, 15 Amp Bat – CCN/Interior PASS Blue Light/SCM/Sw Bank...
Page 541 540 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Description Cavity Cartridge Mini Description Fuse Fuse Fuse Fuse 15 Amp IOD-SDARS/VES 20 Amp IGN R/ACC-Pwr Blue 2–3/DVD/HFM/ Yellow Outlet #2 UGDO/Vanity Lamp 20 Amp IGN R/ACC/Bat-Pwr 10 Amp IOD-HVAC, U/Hood Yellow Outlet #3 Lamp 25 Amp ASD #1, #2...
Page 542: Vehicle Storage
MAINTAINING YOUR VEHICLE 541 VEHICLE STORAGE CAUTION! If you are storing your vehicle for more than 21 days, we • When installing the totally integrated power mod- recommend that you take the following steps to mini- mize the drain on your vehicle’s battery: ule cover, it is important to ensure the cover is properly positioned and fully latched.
Page 543: Replacement Bulbs
542 MAINTAINING YOUR VEHICLE NOTE: NOTE: For lighted switches, see your authorized dealer • When reinstalling the IOD fuse push firmly until fully for replacement instructions. seated; the gauges in the instrument cluster will do a All of the inside bulbs are brass or glass-wedge base. full sweep when the ignition switch is turned to the Aluminum base bulbs are not approved.
Page 544: Bulb Replacement
MAINTAINING YOUR VEHICLE 543 BULB REPLACEMENT Dual or Quad Headlamp/Front Park and Turn Signal — If Equipped 1. Open the hood. 2. Disconnect and isolate the negative battery cable. 3. Remove the four plastic push-in fasteners that secure the upper radiator seal to the grille support and both fender ledges.
Page 545 544 MAINTAINING YOUR VEHICLE 8. Reach through the access hole of the wheel house 10. Disconnect the wiring harness connectors from the splash shield and lift the slide lock upward far enough to bulb socket. disengage it from the lock post on the back of the front 11.
Page 546: Fog Lamps
MAINTAINING YOUR VEHICLE 545 Fog Lamps Rear Tail/Stop, Turn Signal and Backup Lamps 1. Reach under and behind the front bumper to access 1. Remove the two screws that pass through the bed the back of the front fog lamp housing. sheetmetal.
Page 547: Center High-Mounted Stoplamp (Chmsl) With Cargo Lamp
546 MAINTAINING YOUR VEHICLE 2. Pull the outboard side of the lamp rearward far 4. Rotate the bulb socket counterclockwise 1/4 turn to enough to unsnap the two receptacles on the outboard unlock it from the housing. side of the lamp housing from the two plastic snap post 5.
Page 548 MAINTAINING YOUR VEHICLE 547 2. Separate the connector holding the housing and wir- 3. Turn the desired bulb socket ⁄ turn and remove the ing harness to the body. socket and bulb from housing.
Page 549: Cab Top Clearance Lamps - If Equipped
548 MAINTAINING YOUR VEHICLE • Outside Bulbs: Cargo Lamps 4. Pull the desired bulb straight from the socket. • Inside Bulb: Center High-Mounted Stop Lamp 5. Reverse the procedure for installation of bulbs and housing. Cab Top Clearance Lamps — If Equipped 1.
Page 550 MAINTAINING YOUR VEHICLE 549 2. Rotate the socket ⁄ turn and pull it from the lamp 3. Pull the bulb straight from it’s socket and replace. assembly.
Page 551: Rear Lamp Bar Id Marker (Dual Rear Wheels) - If Equipped
550 MAINTAINING YOUR VEHICLE Rear Lamp Bar ID Marker (Dual Rear Wheels) — If 2. Turn the socket ⁄ turn counterclockwise to access the Equipped bulb. 1. Loosen the two screws and the housing to gain access 3. Pull the bulb straight out from the socket. to the bulb sockets.
Page 552: Side Marker Lamps (Dual Rear Wheels) - If Equipped
MAINTAINING YOUR VEHICLE 551 2. Pull the entire assembly from the fender. Side Marker Lamps (Dual Rear Wheels) — If Equipped 3. Turn the socket ⁄ turn counterclockwise and remove from assembly to access the bulb. 4. Pull the bulb straight out from socket. 5.
Page 553: Maintaining Your Vehicle
552 MAINTAINING YOUR VEHICLE FLUID CAPACITIES U.S. Metric Fuel (Approximate) 1500 Regular Cab Shortbed/Crew Quad Cab Models 26 Gallons 98 Liters 1500 Regular Cab Longbed/Crew Quad Cab Models 32 Gallons 121 Liters (Optional) 2500/3500 Shortbed Models 34 Gallons 129 Liters 2500/3500 Longbed Models 35 Gallons 132 Liters...
Page 554 MAINTAINING YOUR VEHICLE 553 U.S. Metric Cooling System 3.7L Engine (MOPAR Antifreeze/Coolant 5 14 Quarts 13 Liters Year/100,000 Mile Formula or equivalent) 4.7L Engine (MOPAR Antifreeze/Coolant 5 14 Quarts 13 Liters Year/100,000 Mile Formula or equivalent) 5.7L Engine — 1500 Models (MOPAR Antifreeze/ 16 Quarts 15 Liters Coolant 5 Year/100,000 Mile Formula or equivalent)
Page 555: Engine
554 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant MOPAR Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. Engine Oil Use API Certified SAE 5W-20 Engine Oil, meeting the re- quirements of Chrysler Material Standard MS-6395.
Page 556: Chassis
MAINTAINING YOUR VEHICLE 555 Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission MOPAR ATF+4 Automatic Transmission Fluid or equivalent licensed ATF+4 product. Transfer Case MOPAR ATF+4 Automatic Transmission Fluid or equivalent licensed ATF+4 product. Transfer Case – NVG 246 Only MOPAR NVG 246 Automatic Transmission Fluid or equivalent.
Page 558 MAINTENANCE SCHEDULES CONTENTS Emissions Control System Maintenance ..558 Required Maintenance Intervals ..560 Maintenance Schedule ....558...
Page 559 558 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE MAINTENANCE SCHEDULE The Scheduled Maintenance services listed in bold type The oil change indicator system will remind you that it is must be done at the times or mileages specified to ensure time to take your vehicle in for scheduled maintenance. the continued proper functioning of the emissions control On Electronic Vehicle Information Center (EVIC) system.
Page 560 MAINTENANCE SCHEDULES 559 “Understanding Your Instrument Panel” or under “In- NOTE: • The oil change indicator message will not monitor the strument Cluster Description/Odometer/Trip Odom- time since the last oil change. Change your vehicle’s eter” in “Understanding Your Instrument Panel” for oil if it has been six months since your last oil change further information.
Page 561 560 MAINTENANCE SCHEDULES • Inspect the battery and clean and tighten the terminals Required Maintenance Intervals as required. NOTE: ** Vehicle’s built with the 4.7L engine are • Check the fluid levels of the coolant reservoir, brake equipped with sixteen spark plugs. One set is located on master cylinder, power steering and transmission and the top of the engine under the coils and the second set is add as needed.
Page 562 MAINTENANCE SCHEDULES 561 6,000 Miles (10,000 km) or 12,000 Miles (20,000 km) or 12 Months Maintenance Service 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. Schedule ❏ Rotate the tires. ❏ Change the engine oil and engine oil ❏...
Page 563 562 MAINTENANCE SCHEDULES 18,000 Miles (30,000 km) or 24,000 Miles (40,000 km) or 24 Months Maintenance Service 18 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires. ❏ Change the engine oil and engine oil ❏...
Page 564 MAINTENANCE SCHEDULES 563 30,000 Miles (50,000 km) or 36,000 Miles (60,000 km) or 36 Months Maintenance Service 30 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires. ❏ Change the engine oil and engine oil ❏...
Page 565 564 MAINTENANCE SCHEDULES 42,000 Miles (70,000 km) or 48,000 Miles (80,000 km) or 48 Months Maintenance Service 42 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires. ❏ Change the engine oil and engine oil ❏...
Page 566 MAINTENANCE SCHEDULES 565 54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires. ❏ Lube the front drive shaft fitting (2500/3500 (4x4) models only). ❏ Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
Page 567 566 MAINTENANCE SCHEDULES 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires. ❏ Replace the engine air cleaner filter. ❏ Replace the ignition cables (3.7L Engine). ❏...
Page 568 MAINTENANCE SCHEDULES 567 66,000 Miles (110,000 km) or 72,000 Miles (120,000 km) or 72 Months Maintenance Service 66 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires. ❏ Change the engine oil and engine oil ❏...
Page 569 568 MAINTENANCE SCHEDULES 78,000 Miles (130,000 km) or 84,000 Miles (140,000 km) or 84 Months Maintenance Service 78 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires. ❏ Change the engine oil and engine oil ❏...
Page 570 MAINTENANCE SCHEDULES 569 90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires. ❏ Replace the engine air cleaner filter. ❏ Replace the spark plugs (3.7L and 5.7L Engines). ❏...
Page 571 570 MAINTENANCE SCHEDULES 96,000 Miles (160,000 km) or 96 Months Maintenance Service 102,000 Miles (170,000 km) or Schedule 102 Months Maintenance ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires. ❏ Change the engine oil and engine oil ❏...
Page 572 MAINTENANCE SCHEDULES 571 108,000 Miles (180,000 km) or 108 Months Maintenance Service 114,000 Miles (190,000 km) or Schedule 114 Months Maintenance ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires. ❏ Change the engine oil and engine oil ❏...
Page 573 572 MAINTENANCE SCHEDULES 120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires. ❏ Replace the engine air cleaner filter. ❏ Replace the ignition cables (3.7L Engine). ❏...
Page 574 MAINTENANCE SCHEDULES 573 126,000 Miles (210,000 km) or 132,000 Miles (220,000 km) or 132 Months Maintenance Service 126 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires. ❏ Change the engine oil and engine oil ❏...
Page 575 574 MAINTENANCE SCHEDULES 138,000 Miles (230,000 km) or 144,000 Miles (240,000 km) or 144 Months Maintenance Service 138 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires. ❏ Change the engine oil and engine oil ❏...
Page 576 MAINTENANCE SCHEDULES 575 † This maintenance is recommended by the manufacturer 150,000 Miles (250,000 km) or to the owner, but is not required to maintain emissions 150 Months Maintenance Service warranty. Schedule ❏ Change the engine oil and engine oil filter. ❏...
Page 578 IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Customer Assistance For The Hearing Or Vehicle......579 Speech Impaired (TDD/TTY) .
Page 579 578 IF YOU NEED CONSUMER ASSISTANCE Publication Order Forms ....583 Traction Grades ..... 585 Department Of Transportation Uniform Tire Temperature Grades .
Page 580: If You Need Consumer Assistance 579
IF YOU NEED CONSUMER ASSISTANCE 579 the service advisor and list the items in order of priority. SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the...
Page 581 580 IF YOU NEED CONSUMER ASSISTANCE • Vehicle delivery date and mileage This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- Chrysler Group LLC Customer Center solved with this process. P.O.
Page 582 IF YOU NEED CONSUMER ASSISTANCE 581 the manufacturer’s service contracts. If you purchased a Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) manufacturer’s service contract, you will receive Plan To assist customers who have hearing difficulties, the Provisions and an Owner Identification Card in the mail manufacturer has installed special TDD (Telecommuni- within three weeks of the vehicle delivery date.
Page 583 582 IF YOU NEED CONSUMER ASSISTANCE has also made a major investment in facilities, tools, and WARRANTY INFORMATION (U.S. Vehicles Only) training to assure that you are absolutely delighted with See the Warranty Information Booklet, located on the the ownership experience. You’ll be pleased with their DVD, for the terms and provisions of Chrysler Group sincere efforts to resolve any warranty issues or related LLC warranties applicable to this vehicle.
Page 584: Publication Order Forms
IF YOU NEED CONSUMER ASSISTANCE 583 If NHTSA receives similar complaints, it may open an Transport Canada, Motor Vehicle Defect Investigations investigation, and if it finds that a safety defect exists in and Recalls, 2780 Sheffield Road, Ottawa, Ontario K1B a group of vehicles, it may order a recall and remedy 3V9.
Page 585: Quality Grades
584 IF YOU NEED CONSUMER ASSISTANCE vehicle, system, and/or components is written in acquaint you with specific Chrysler Group LLC ve- straightforward language with illustrations, diagrams, hicles. Included are starting, operating, emergency and charts. and maintenance procedures as well as specifications, capabilities and safety tips.
Page 586: Traction Grades
IF YOU NEED CONSUMER ASSISTANCE 585 in each category is shown on the sidewall of the tires on wet pavement, as measured under controlled conditions your vehicle. on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction perfor- All passenger car tires must conform to Federal safety mance.
Page 587 586 IF YOU NEED CONSUMER ASSISTANCE grade C corresponds to a level of performance, which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A repre- sent higher levels of performance on the laboratory test wheel, than the minimum required by law.
Page 588 INDEX...
Page 589 588 INDEX Adding Fuel ......436 Alarm System (Security Alarm) ....18 Adjustable Pedals .
Page 590 INDEX 589 Fluid Type ......528,555 Brake System ......379,525 Gear Ranges .
Page 591 590 INDEX Radiator (Coolant Pressure) ....522 Cleaning Car Washes ......532 Wheels .
Page 592 INDEX 591 Coolant Level ..... . 520,523 Dipsticks Disposal of Used Coolant ....523 Automatic Transmission .
Page 593 592 INDEX Electronic Brake Control System ... . . 382 Engine ......502,503,504 Anti-Lock Brake System .
Page 594 INDEX 593 Exterior Lighting ......116 Fluid Capacities ......552 Exterior Lights .
Page 595 594 INDEX Octane Rating ..... . 427,554 Speedometer ......203 Requirements .
Page 596 INDEX 595 Automatic ......116 Ignition ....... 14 Cleaning .
Page 597 596 INDEX Jack Location ......472 Life of Tires ......409 Jump Starting .
Page 598 INDEX 597 Four-Wheel Drive Indicator ....318 Tire Pressure Monitoring (TPMS) ... 213 Hazard Warning Flasher ....472 Traction Control .
Page 599 598 INDEX Maintenance Schedule ....558 Monitor, Tire Pressure System ....417 Malfunction Indicator Light (Check Engine) .
Page 600 INDEX 599 Dipstick ......509 Owner’s Manual (Operator Manual) ..4,583 Disposal .
Page 601 600 INDEX Sliding Rear Window ....172 Rear Seat, Folding ..... . . 106 Steering .
Page 602 INDEX 601 Reporting Safety Defects ....582 Adjustable Upper Shoulder Anchorage ..46 Resetting Oil Change Indicator ... 208,226 And Pregnant Women .
Page 603 602 INDEX Selection of Coolant (Antifreeze) ..521,554 Sliding Rear Window Sentry Key (Immobilizer) ....15 Power .
Page 604 INDEX 603 Steering Wheel Mounted Sound System Tire Identification Number (TIN) ... . . 398 Controls ......276 Tire Markings .
Page 605 604 INDEX Safety ......394,404 Minimum Requirements ....447 Sizes .
Page 606 INDEX 605 Transmitter, Remote Keyless Entry (RKE) ..20 Voice Recognition System (VR) ....94 Tread Wear Indicators ....409 Voltmeter .
Page 607 606 INDEX Usage ......356 Windshield Washers ....123,124,516 Wind Buffeting .
Page 608 Chrysler Group LLC 10D241-126-AB Printed in U.S.A. 2nd Edition...

This manual is also suitable for:

Ram truck 2010

Dodge Ram Truck Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

Quick Links

Chapters

Related Manuals for Dodge Ram Truck

Summary of Contents for Dodge Ram Truck