Page 1 2009 OWNER’S MANUAL...
Page 2 VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name This manual illustrates and describes the operation of Chrysler LLC shall be deemed to be deleted and the features and equipment that are either standard or op- name Chrysler Canada Inc.
Page 3 TABLE OF CONTENTS SECTION PAGE ............. 3 INTRODUCTION .
Page 5 INTRODUCTION CONTENTS Introduction ......4 Vehicle Identification Number ... . . 6 How To Use This Manual .
Page 6: Introduction
4 INTRODUCTION INTRODUCTION When it comes to service, remember that your authorized This Owner’s Manual has been prepared with the assis- dealer knows your vehicle best, has the factory-trained tance of service and engineering specialists to acquaint technicians and genuine MOPAR parts, and is inter- you with the operation and maintenance of your vehicle.
Page 7 INTRODUCTION 5...
Page 8: Warnings And Cautions
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against op- erating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information.
Page 9 INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 11: Table Of Contents
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Vehicle Security Alarm ....18 Wireless Ignition Node (WIN) .
Page 12 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Open The Trunk ....24 Trunk Lock And Release ....34 Using The Panic Alarm .
Page 13 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 Event Data Recorder (EDR) ... . . 56 Exhaust Gas ......68 Child Restraint .
Page 14: A Word About Your Keys
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Your vehicle uses a keyless ignition system. This system consists of a Fob with Integrated Key and a Wireless Ignition Node (WIN) with an integral ignition switch. You can insert the double-sided integrated key into the ignition switch with either side up.
Page 15: Fob With Integrated Key
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Fob With Integrated Key The Fob with Integrated Key operates the ignition switch. It also contains the Remote Keyless Entry (RKE) trans- mitter and a valet key, which stores in the rear of the Fob. The valet key allows for entry into the vehicle should the battery in the vehicle or the Fob go dead.
Page 16: Key-In-Ignition Reminder
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The power window switches, radio, power CAUTION! sunroof (if equipped), and ignition-powered power out- lets will remain active for up to 60 minutes after the An unlocked car is an invitation to thieves. Always ignition switch is turned to the LOCK position.
Page 17: Sentry Key
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 If the Vehicle Security Light turns on during normal vehicle SENTRY KEY operation (vehicle running for longer than 10 seconds), it The Sentry Key Immobilizer System prevents unautho- indicates that there is a fault in the electronics. Should this rized vehicle operation by disabling the engine.
Page 18: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Replacement Keys programming a blank transmitter to the vehicle electron- ics. A blank transmitter is one that has never been NOTE: Only RKE transmitters that are programmed to programmed. the vehicle electronics can be used to start and operate the vehicle.
Page 19: General Information
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 2. Insert the second valid integrated key and turn the NOTE: If a programmed key is lost, see your authorized ignition switch to the ON position within 15 seconds. dealer to have all remaining keys erased from the sys- After 10 seconds, a chime will sound and the Vehicle tem’s memory.
Page 20: Vehicle Security Alarm
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE VEHICLE SECURITY ALARM To Arm The System The Vehicle Security Alarm monitors the vehicle doors Remove the key from the ignition switch and either press for unauthorized entry and the ignition switch for unau- a power door LOCK switch while the driver or passenger thorized operation.
Page 21: Illuminated Entry System
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 NOTE: vehicle and open a door, the alarm will sound. If this • The driver’s door key cylinder and the trunk button on occurs, disarm the Vehicle Security Alarm. the RKE transmitter cannot arm or disarm the Vehicle If the Vehicle Security Alarm is armed and the battery Security Alarm.
Page 22: Remote Keyless Entry
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The lights will fade to off after about 30 seconds or they NOTE: Inserting the Fob with Integrated Key into the will immediately fade to off once the ignition switch is ignition switch disables all buttons on that transmitter; turned ON from the LOCK position.
Page 23: To Unlock The Doors
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 To Unlock The Doors 1. Press and hold the LOCK button on a programmed Press and release the UNLOCK button on the transmitter transmitter for at least four seconds, but no longer than once to unlock the driver’s door, or twice within five 10 seconds.
Page 24 22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Flash Lights with Remote Key Lock 3. Test the feature while outside of the vehicle by press- This feature will cause the turn signal lights to flash when ing the LOCK/UNLOCK buttons on the transmitter with the doors are locked or unlocked with the transmitter.
Page 25: To Lock The Doors
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 Headlights On with Remote Key Unlock,” under “Per- 1. Press the LOCK button on a programmed transmitter sonal Settings (Customer Programmable Features),” un- for at least four seconds, but no longer than 10 seconds. der “Electronic Vehicle Information Center (EVIC)”...
Page 26: Express Down Window Feature
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Express Down Window Feature The Panic Alarm will stay on for three minutes unless This feature allows you to remotely lower both door you turn it off by either pressing the PANIC button a windows at the same time.
Page 27: Programming Additional Transmitters
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Programming Additional Transmitters Refer to Sentry Key “Customer Key Programming.” If you do not have a programmed RKE transmitter, contact your authorized dealer for details. Transmitter Battery Service The recommended replacement battery is one CR2032 battery.
Page 28: General Information
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Reposition the access door panel over the battery 1. A weak battery in the transmitter. The expected life of opening and snap into place. the battery is a minimum of three years. 2.
Page 29 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 • Doors closed NOTE: • If an engine fault is present the vehicle will start and • Hood closed then shut down 10 seconds later. • Hazard switch off • The park lamps will turn on and remain on during •...
Page 30: Door Locks
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles equipped with the Electronic Vehicle NOTE: To avoid unintentional shut downs, the system will disable the one time press of the REMOTE START Information Center (EVIC), the message “Insert Key/ button for two seconds after receiving a valid Remote Turn To Run”...
Page 31: Power Door Locks
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors before you drive as well as when you park and leave the vehicle. • When leaving the vehicle, always remove the key from the ignition and lock your vehicle.
Page 32 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE is open, the key is in the ignition, and the ignition is in the LOCK or ACC position, a chime will sound as a reminder to remove the key. Automatic Door Locks The doors will lock automatically if all of the following conditions are met: 1.
Page 33 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Automatic Door Locks — If Equipped Automatic Unlock Doors on Exit Programming The auto door lock feature can be enabled or disabled by The Automatic Unlock Doors On Exit feature can be your authorized dealer.
Page 34: Windows
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. A single chime will indicate the completion of the programming. NOTE: If you do not hear the chime, it means that the system did not enter the programming mode and you will need to repeat the procedure.
Page 35 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 NOTE: AUTO-Down Feature • The door window will lower slightly if it is closed The driver’s door power window switch and passenger completely when opening the door. The window will door power window switch have an AUTO-down fea- return to its fully closed position after closing the door.
Page 36: Wind Buffeting
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.
Page 37: Trunk Safety Warning
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 With the ignition switch in the ON position, the Trunk TRUNK SAFETY WARNING Open symbol will display in the instrument cluster WARNING! indicating that the trunk is open. The odometer display will reappear once the trunk is closed. Do not allow children to have access to the trunk, With the ignition switch in the LOCK position or the key either by climbing into the trunk from outside, or...
Page 38: Trunk Emergency Release
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Trunk Emergency Release OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, the front airbags for both the driver and front passenger, and the supplemental side curtain airbags for the driver and passengers seated next to a window.
Page 39: Lap/Shoulder Belts
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 ejection and the risk of injury caused by striking the WARNING! inside of the vehicle. Everyone in a motor vehicle should be belted at all times. In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled Lap/Shoulder Belts up.
Page 40 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Wearing your belt in the wrong place could make • It is extremely dangerous to ride in a cargo area, your injuries in a collision much worse. You might inside or outside of a vehicle.
Page 41 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 2. The seat belt latch plate is contacting the seat when the 3. When the belt is long enough to fit, insert the latch belt is routed through the seat web guide. When the belt plate into the buckle until you hear a “click.”...
Page 42 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • A shoulder belt placed behind you will not protect • A belt that is buckled into the wrong buckle will you from injury during a collision. You are more not protect you properly.
Page 43 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen.
Page 44: Lap/Shoulder Belt Untwisting Procedure
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. At about 6 to 12 in (15 to 30 cm) above the latch plate, WARNING! grasp and twist the belt webbing 180 degrees to create a fold that begins immediately above the latch plate. A frayed or torn belt could rip apart in a collision and leave you with no protection.
Page 45: Enhanced Seat Belt Use Reminder System (Beltalert )
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 NOTE: These devices are not a substitute for proper seat chime and flash the Seat Belt Reminder Light for 96 sec- belt placement by the occupant. The seat belt still must be onds or until the driver’s seat belt is buckled.
Page 46: Automatic Locking Mode - If Equipped
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: You must perform the following steps within NOTE: When the BeltAlert is deactivated, the Seat Belt 60 seconds of turning the ignition switch to the ON Reminder Light will continue to illuminate as long as the position.
Page 47: Seat Belts And Pregnant Women
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 3. Allow the belt to retract. As the belt retracts, you will Seat Belt Extender here a clicking sound. This indicates the safety belt is If a seat belt is too short even when fully extended your now in the Automatic Locking mode.
Page 48: Driver And Front Passenger Supplemental Restraint System (Srs) - Airbag
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver and Front Passenger Supplemental Restraint System (SRS) - Airbag This vehicle has front airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver side front airbag is mounted in the center of the steering wheel.
Page 49 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 The front airbags have a multistage inflator design. This This vehicle is also equipped with supplemental side allows the airbag to have different rates of inflation that curtain airbags (located above the side windows) to are based on collision severity.
Page 50 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE protection for the driver and front passenger. Side curtain WARNING! airbags also work with seat belts to improve occupant • Do not stack luggage or other cargo up high protection. enough to block the location of the side curtain While the seat belts are designed to protect you in many airbag.
Page 51 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 seat as far back as possible and use the proper child WARNING! restraint. (Refer to information on Child Restraint in this section.) Infants in rear-facing child restraints should NEVER ride in the front seat of a vehicle with a passenger 5.
Page 52 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag System Components WARNING! The airbag system consists of the following: • Relying on the airbags alone could lead to more • Occupant Restraint Controller (ORC) severe injuries in a collision. The airbags work •...
Page 53 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 • Interconnecting Wiring • The ORC also monitors the readiness of the electronic parts of the system whenever the ignition switch is in • Seat Belt Reminder Light the START or ON position. These include all of the •...
Page 54 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE their full size. The bags fully inflate in about 50 to 70 WARNING! milliseconds. This is about half of the time that it takes to blink your eyes. The bags then quickly deflate while Ignoring the AIRBAG Warning Light in your instru- helping to restrain the driver and front passenger.
Page 55 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 inflating side curtain airbag pushes the outside edge of If you do have a collision that deploys the airbags, any or the headliner out of the way and covers the window. all of the following may occur: The airbag inflates in about 30 milliseconds (about •...
Page 56 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE irritation, move to fresh air. If the irritation continues, network intact, and the power intact, the Enhanced see your doctor. If these particles settle on your Accident Response System performs the following func- clothing, follow the garment manufacturer’s instruc- tions: tions for cleaning.
Page 57 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Maintaining Your Airbag System NOTE: Perchlorate Material — special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate. WARNING! Airbag Warning Light • Modifications to any part of the airbag system You will want to have the airbags ready to inflate for your protection in an impact.
Page 58: Event Data Recorder (Edr)
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Event Data Recorder (EDR) In conjunction with other data gathered during a com- In the event of an accident, your vehicle is designed to plete accident investigation, the electronic data may be record up to five seconds of specific vehicle data param- used by Chrysler LLC and others to learn more about the eters (see the following list) in an event data recorder...
Page 59 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 upon request. General data that does not identify par- Data Parameters that May Be Recorded: ticular vehicles or crashes may be released for incorpo- • Diagnostic trouble code(s) and warning light status for ration in aggregate crash databases, such as those main- electronically-controlled safety systems, including the tained by the U.S.
Page 60: Child Restraint
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Cruise control status WARNING! • Traction/stability control status In a collision, an unrestrained child, even a tiny baby, • Tire Pressure Monitoring System status (if equipped) can become a missile inside the vehicle. The force required to hold even an infant on your lap could Child Restraint become so great that you could not hold the child, no...
Page 61 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 Infants and Child Restraints “LATCH — Child Seat Anchorage System (Lower Anchors and Tether for CHildren)” in this section. • Safety experts recommend that children ride • Rearward-facing child seats must NEVER be used in rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg).
Page 62 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Check belt fit periodically. A child’s squirming or The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit slouching can move the belt out of position. the vehicle’s seat belts properly.
Page 63 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 • Carefully follow the instructions that come with the WARNING! (Continued) restraint. If you install the restraint improperly, it may • A rearward-facing child restraint should only be not work when you need it. used in a rear seat.
Page 64 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the child restraint using lower anchorages and upper child seats. You should NEVER install LATCH- tether straps from the child restraint to the vehicle compatible child seats so that two seats share a common structure.
Page 65 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 Installing the LATCH-Compatible Child Restraint window. These tether strap anchorages are under a System plastic cover with this symbol on it. We urge you to follow the manufacturer’s directions Many, but not all restraint systems will be equipped with carefully when installing your child restraint.
Page 66 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE most direct path between the anchor and the child the child restraint belt path and then buckle it. This restraint. Finally, tighten all three straps as you push the should stow the seat belt out of the reach of an child restraint rearward and downward into the seat, inquisitive child.
Page 67 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 restraint so that it is not necessary to use a locking clip. In the rear seat, you may have trouble tightening the Pulling up on the shoulder portion of the lap/shoulder lap/shoulder belt on the child restraint because the belt will tighten the belt.
Page 68 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Ensure that the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap. WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child.
Page 69: Engine Break-In Recommendations
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 ENGINE BREAK-IN RECOMMENDATIONS CAUTION! A long break-in period is not required for the drivetrain (engine, transmission, and rear axle) in your new vehicle. Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result. Drive moderately during the first 500 mi (800 km).
Page 70: Safety Tips
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SAFETY TIPS Exhaust Gas Transporting Passengers WARNING! NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. WARNING! Breathing it can make you unconscious and can eventually poison you.
Page 71: Safety Checks You Should Make Inside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 If you are required to drive with the trunk/liftgate open, Safety Checks You Should Make Inside The make sure that all windows are closed and the climate Vehicle control BLOWER switch is set at high speed. DO NOT Seat Belts use the recirculation mode.
Page 72: Periodic Safety Checks You Should Make Outside The Vehicle
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Defroster Lights Check operation by selecting the defrost mode and place Have someone observe the operation of exterior lights the blower control on high speed. You should be able to while you work the controls. Check turn signal and high feel the air directed against the windshield.
Page 73 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors ......75 Slide On Rod And Extender Features Of Sun Visor .
Page 74 72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Recognition System (VR) To Open And Close The Hood ... 119 — If Equipped ......107 Lights .
Page 75 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73 Windshield Wipers And Washers ..126 To Accelerate For Passing ... . . 132 Intermittent Wiper System .
Page 76 74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Sunroof — If Equipped ... 140 Ignition Off Operation ....143 Opening Sunroof - Partially .
Page 77: Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 MIRRORS Automatic Dimming Inside Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light next to the button will illuminate to indicate when the dimming feature is activated.
Page 78: Outside Mirrors
76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirrors Outside Mirrors Folding Feature To receive maximum benefit, adjust the outside mirror(s) All models have exterior mirrors that are hinged. The to center on the adjacent lane of traffic and a slight hinge allows the mirror to pivot forward and rearward to overlap of the view obtained from the inside mirror.
Page 79: Heated Mirrors - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster. Refer to “Rear Window Features” in this Section, for further information. Vanity Mirrors An vanity mirror is on the sun visor.
Page 80: Slide On Rod And Extender Features Of Sun Visor
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE visor, grab the extender which is located at the rear of the visor and pull rearward. Illuminated Vanity Mirror Slide On Rod and Extender Features of Sun Visor To use the slide on rod feature of the sun visor, rotate the Slide On Rod Extender sun visor downward and swing the sun visor so it is parallel to the side window, grabbing the sun visor with...
Page 81: Uconnect Phone - If Equipped
NOTE: The sales code RER and REU radios contain an integrated uconnect phone. Refer to your “Navigation • www.chrysler.com/uconnect User’s Manual” for uconnect phone operating instruc- • www.dodge.com/uconnect tions for these radios. Radio sales code can be located on the lower right corner of the Radio faceplate. • www.jeep.com/uconnect...
Page 82 80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE it your purse, pocket, or briefcase), as long as your phone The uconnect phone can be used with any Hands-Free is turned on and has been paired to the vehicle’s Profile certified Bluetooth cellular phone.
Page 83: Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 Operation example, you can use the combined form voice com- Voice commands can be used to operate the uconnect mand Phonebook New Entry, or you can break the phone and to navigate through the uconnect phone combined form command into two voice commands: menu structure.
Page 84 82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, after the beep, say Pair a Phone and Cancel Command At any prompt, after the beep, you can say Cancel and follow the audible prompts. you will be returned to the main menu. However, in a •...
Page 85 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 • The uconnect phone will confirm the phone number phone to use if multiple cellular phones are in the vehicle at the same time. For example, if priority three and then dial. The number will appear in the display and priority five phones are present in the vehicle, the of certain radios.
Page 86 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The uconnect system will confirm the name and then • When prompted, enter the number designation (e.g., dial the corresponding phone number, which may Home, Work, Mobile, or Pager ). This will allow appear in the display of certain radios.
Page 87 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 • Depending on the maximum number of entries down- Phonebook Download – Automatic Phonebook Transfer From Cellular Phone loaded, there may be a short delay before the latest If equipped and specifically supported by your phone, downloaded names can be used.
Page 88 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phonebook Download — Single Entry first disconnect or drop the Bluetooth connection to If equipped and supported by your phone, uconnect the uconnect phone, and then send the address book phone allows the user to download entries from their entry via Bluetooth .
Page 89 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 • You will then be asked for the name of the phonebook Delete uconnect Phonebook Entry entry that you wish to edit. NOTE: Editing phonebook entries is recommended • Next, choose the number designation (home, work, when the vehicle is not in motion.
Page 90 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After you enter the name, the uconnect phone will • Note that only the phonebook in the current language ask you which designation you wish to delete: home, is deleted. work, cellular, pager, or all. Say the designation you •...
Page 91: Phone Call Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 • The uconnect phone will then prompt you as to the Answer or Reject an Incoming Call - Call number designation you wish to call. Currently in Progress If a call is currently in progress and you have another •...
Page 92 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE refer to Toggling Between Calls in this section. To Three-Way Calling combine two calls, refer to Conference Call in this To initiate three-way calling, press the VOICE RECOG- section. NITION button while a call is in progress, and make a second phone call, as described under Making a Second Place/Retrieve a Call From Hold Call While Current Call is in Progress.
Page 93: Uconnect Phone Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 • After the Ready prompt and the following beep, say • After the ignition key is switched to OFF, a call can Redial. continue on the uconnect phone for a certain dura- tion, after which the call is automatically transferred •...
Page 94 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Continue to follow the system prompts to complete • Press the PHONE button to begin. the language selection. • After the Ready prompt and the following beep, say After selecting one of the languages, all prompts and Emergency and the uconnect phone will instruct voice commands will be in that language.
Page 95 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 • The uconnect phone does slightly lower your chances NOTE: • The towing assistance number dialed is based on the of successfully making a phone call as to that for the cell phone directly. country where the vehicle is purchased (1-800-528- 2069 for the U.S., 1-877-213-4525 for Canada, 55-14- WARNING!
Page 96 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Working with Automated Systems navigating through an automated customer service cen- This method is used in instances where one generally has ter menu structure, and to leave a number on a pager. to press numbers on the cellular phone keypad while You can also send stored uconnect phonebook entries as navigating through an automated telephone system.
Page 97 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 Barge In - Overriding Prompts Phone and Network Status Indicators The “Voice Recognition” button can be used when you If available on the radio and/or on a premium display wish to skip part of a prompt and issue your voice such as the instrument panel cluster, and supported by recognition command immediately.
Page 98: Advanced Phone Connectivity
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Following the beep, say Mute off. NOTE: Certain brands of cellular phones do not send the dial ring to the uconnect phone to play it on the Advanced Phone Connectivity vehicle audio system, so you will not hear it. Under this situation, after successfully dialing a number the user Transfer Call to and from Cellular Phone may feel that the call did not go through even though the...
Page 99 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 If you would like to connect or disconnect the Bluetooth Select Another Cellular Phone connection between a uconnect phone paired cellular This feature allows you to select and start using another phone and the uconnect phone, follow the instructions phone paired with the uconnect phone.
Page 100: Things You Should Know About Your Uconnect Phone
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Delete uconnect phone Paired Cellular Phones Voice Training For users experiencing difficulty with the system recog- • Press the PHONE button to begin. nizing their voice commands or numbers, the uconnect • After the Ready prompt and the following beep, say phone Voice Training feature may be used.
Page 101 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 • Performance is maximized under: This procedure may be repeated with a new user. The system will adapt to the last trained voice only. • low-to-medium blower setting, To restore the Voice Recognition system to factory default •...
Page 102 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • It is not recommended to store similar sounding • low-to-medium vehicle speed, names in the uconnect phonebook. • low road noise, • Phonebook (Downloaded and uconnect phone Local) • smooth road surface, name recognition rate is optimized when the entries •...
Page 103 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 Bluetooth Communication Link Power-Up Cellular phones have been found to lose connection to After switching the ignition key from OFF to either the the uconnect phone. When this happens, the connection ON or ACC position, or after a language change, you can generally be reestablished by switching the phone must wait at least five seconds prior to using the system.
Page 104 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 105 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103...
Page 106 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 107 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) zero call cancel confirmation prompts three continue four delete five dial download seven edit eight emergency nine English star (*) erase all plus (+) Espanol pound (#) Francais add location...
Page 108 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) language return to main menu return or main menu list names select phone select list phones send mobile set up phone settings or phone set up mute towing assistance mute off...
Page 109: General Information
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 General Information VOICE RECOGNITION SYSTEM (VR) — IF This device complies with Part 15 of the FCC rules and EQUIPPED RSS 210 of Industry Canada. Operation is subject to the Voice Recognition System (VR) Operation following conditions: This Voice Recognition system allows you to •...
Page 110 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When you press the VR button, you will hear a beep. The These commands are universal and can be used from any beep is your signal to give a command. menu. All other commands can be used depending upon the active application.
Page 111: Commands
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Commands In this mode, you can say the following commands: The Voice Recognition system understands two types of • “Radio” (to switch to the radio mode) commands. Universal commands are available at all •...
Page 112 110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • “Previous Channel” (to select the previous channel) Radio FM To switch to the FM band say “FM” or “Radio FM”. In • “List Channel” (to hear a list of available channels) this mode, you may say the following commands: •...
Page 113 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Memo − “Previous” (to play the previous memo) To switch to the voice recorder mode say “Memo”. In this − “Delete” (to delete a memo) mode, you may say the following commands: • “Delete All” (to delete all memos) •...
Page 114: Voice Training
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Keep in mind that you have to press the VR SEATS button first and wait for the beep before speaking the Easy Entry Seats “Barge In” commands. Pulling upward on the lever, located on the seatback, Voice Training allows the seatback to dump forward and the seat to slide For users experiencing difficulty with the system recog-...
Page 115: Power Seats
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 used to adjust the angle of the seatback. Push forward or rearward on the switch to change the position of the seatback. Easy Entry Seats Power Seats The power seat switches are on the outboard side of the front seat cushions.
Page 116: Manual Front Seatback Recline
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked.
Page 117: Lumbar Support
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Lumbar Support Head Restraints This feature allows you to increase or decrease the Head restraints can reduce the risk of whiplash injury in amount of lumbar support. Turn the control lever for- the event of impact from the rear. Adjust the restraint so ward to increase and rearward to decrease the desired that the upper edge is as high as practical.
Page 118: Heated Seats
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats The driver seat and front passenger seat are heated. The heaters provide the same heat level for both cushion and seatback. The controls for each heater are located near the bottom center of the instrument panel.
Page 119: Folding Rear Seat
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 If high level heating is selected, the system will automati- WARNING! (Continued) cally switch to the low level after 30 minutes of continu- • Do not place anything on the seat that insulates ous operation.
Page 120 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position, the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury.
Page 121: To Open And Close The Hood
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 TO OPEN AND CLOSE THE HOOD 2. Move to the outside of the vehicle and push the safety Two latches must be released to open the hood. catch to the left. The safety catch is located under the center front edge of the hood.
Page 122: Lights
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS CAUTION! Headlight Switch To prevent possible damage, do not slam the hood to The headlight switch is located on the left side of the close it. Lower the hood until it is open approxi- instrument panel.
Page 123: Automatic Headlights - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch counterclockwise to the AUTO (A) position. When the system is on, the headlight time delay feature is also on.
Page 124: Headlight Time Delay
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE position. In addition, the headlights will turn off when If you turn the headlights, parking lights, or ignition the wipers are turned off if they were turned on by this switch ON again, the system will cancel the delay. feature.
Page 125: Lights-On Reminder
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Lights-On Reminder Multifunction Lever If the headlights or parking lights are on after the ignition The multifunction lever controls the operation of the turn is turned OFF, a chime will sound to alert the driver signals, headlight beam selection, and passing lights.
Page 126: Overhead Console Map/Reading Lights
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Signals High Beam/Low Beam Select Switch Move the multifunction lever up or down and the Push the multifunction lever away from you to switch corresponding turn signal indicator in the instrument the headlights to high beam. Pull the multifunction lever cluster flashes to show proper operation of the front and toward you to switch the headlights back to low beam.
Page 127: Interior Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 because a door is open. This includes the glove box light, but not the trunk light. To restore interior light operation, either turn the ignition switch ON or cycle the light switch. Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel.
Page 128: Windshield Wipers And Washers
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dome Light Position the ON position. The multifunction lever is located on the Rotate the dimmer control completely upward to the left side of the steering column. second detent to turn on the interior lights. The interior lights will remain on when the dimmer control is in this position.
Page 129: Intermittent Wiper System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 CAUTION! WARNING! Turn the windshield wipers off when driving Sudden loss of visibility through the windshield through an automatic car wash. Damage to the wind- could lead to an accident. You might not see other shield wipers may result if the wiper switch is left in vehicles or other obstacles.
Page 130: Headlights On With Wipers (Available With Auto Headlights Only)
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you activate the washer while the windshield wiper The Headlights On with Wipers feature can be enabled or control is in the delay range, the wipers will operate for disabled. Refer to ”Headlights On with Wipers,” under two wipe cycles after releasing the multifunction lever “Personal Settings (Customer-Programmable Features)”...
Page 131: Electronic Speed Control
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 outward or push it inward as desired. To lock the steering column in position, push the control handle inward until fully engaged. WARNING! Do not adjust the steering wheel while driving. The telescoping adjustment must be locked while driv- ing.
Page 132: To Activate
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Activate Push and release the ON/OFF button located on the end of the Electronic Speed Control lever. The indicator light in the instrument cluster will illuminate to show that the speed control system is on. To turn the system off, push and release the ON/OFF button again.
Page 133: To Set At A Desired Speed
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 • Depress the brake pedal, press the clutch pedal to the To Set At A Desired Speed When the vehicle reaches the speed desired, push the floor (manual transmission), or lever downward to SET DECEL and release. Remove •...
Page 134: To Accelerate For Passing
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tapping the lever to RESUME ACCEL once will result in Using Electronic Speed Control on Hills a 1 mph (1.6 km/h) speed increase. Each time the lever is NOTE: The Electronic Speed Control system maintains tapped speed increases, so tapping the lever three times speed up and down hills.
Page 135: Overhead Console
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions and you could lose control. An accident could be the result. Don’t use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.
Page 136: Sunglasses Storage
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE These lights also turn on when a door is opened, or when The HomeLink buttons are located in the overhead the UNLOCK button on the Remote Keyless Entry (RKE) console, and contain one, two, or three dots/lines desig- transmitter is pressed, or when the dimmer control is nating the different HomeLink channels.
Page 137: Programming Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 Programming HomeLink WARNING! Before You Begin • Your motorized door or gate will open and close If you have not trained any of the HomeLink buttons, while you are training the Universal Transceiver. erase all channels before you begin training.
Page 138 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) NOTE: Some gate operators and garage door openers from the HomeLink buttons while keeping the EVIC may require you to replace Step 3 with procedures noted display in view.
Page 139 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 This can usually be found where the hanging antenna 6. Firmly press and release the “learn” or “training” wire is attached to the garage door opener motor (it is button. The name and color of the button may vary by NOT the button normally used to open and close the manufacturer.
Page 140: Gate Operator/Canadian Programming
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Gate Operator/Canadian Programming has successfully accepted the frequency signal. The Canadian radio-frequency laws require transmitter sig- EVIC display will change from “CHANNEL # TRAIN- nals to “time-out” (or quit) after several seconds of ING”...
Page 141: Reprogramming A Single Homelink Button
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Reprogramming A Single HomeLink Button The HomeLink Universal Transceiver is disabled when To reprogram a channel that has been previously trained, the Vehicle Security Alarm is active. follow these steps: Troubleshooting Tips 1. Turn the ignition switch to the ON/RUN position. If you are having trouble programming HomeLink , here are some of the most common solutions: 2.
Page 142: General Information
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information POWER SUNROOF — IF EQUIPPED This device complies with FCC rules Part 15 and Industry The power sunroof switch is located between the sun Canada RSS-210. Operation is subject to the following visors on the overhead console.
Page 143: Opening Sunroof - Partially
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Opening Sunroof - Partially WARNING! Press and hold the switch in the rearward position. • Never leave children in a vehicle with the key in Release the switch when the sunroof is in the position desired and it will stop moving.
Page 144: Closing Sunroof - Express
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the switch in the forward position, the sunroof will close Pinch Protect Override fully and then stop automatically. Release the switch once If a known obstruction (ice, debris, etc.) prevents closing, the sunroof stops moving. press the switch forward and hold for two seconds after the reversal occurs.
Page 145: Wind Buffeting
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 NOTE: The sunshade cannot be closed if the sunroof is this feature is programmable. Refer to “Delay Power Off open. to Accessories Until Exit,” under “Personal Settings (Customer-Programmable Features)” under “Electronic Wind Buffeting Vehicle Information Center (EVIC)”...
Page 146 144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! To avoid serious injury or death: • Do not use a three-prong adapter. • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle.
Page 147 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 CAUTION! CAUTION! (Continued) • Power outlets are designed for accessory plugs • Many accessories that can be plugged in draw only. Do not hang any type of accessory or acces- power from the vehicle’s battery even when not in sory bracket from the plug.
Page 148: Cupholders
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS Illuminated Front Cupholders — If Equipped The front cupholders are illuminated with LEDs. They Front Cupholders are turned on with the headlights or parking lights. Refer The front cupholders are located in the center console. to “Interior Lights”...
Page 149: Console Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 CONSOLE FEATURES Sliding Center Console Armrest The center console armrest slides forward with three detents to provide flexibility for comfort, cupholder use, and shifting ease. Rear Cupholders Sliding Console Armrest...
Page 150: Console Storage
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Console Storage The center console has a storage compartment located underneath the armrest, and also contains a 12-Volt power outlet, a molded-in coin holder (designed to hold various size coins). The center console may also be equipped with a Universal Consumer Interface (UCI).
Page 151: Rear Window Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 REAR WINDOW FEATURES CAUTION! Rear Window Defroster Failure to follow these cautions can cause damage to The pushbutton for the rear window defroster is the heating elements: located on the mode knob of the climate control •...
Page 153: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....155 Trip Functions ..... 173 Instrument Cluster –...
Page 154 152 UNDERSTANDING YOUR INSTRUMENT PANEL Sales Code REQ — AM/FM Stereo Radio And Operating Instructions — uconnect phone 6–Disc CD Changer (MP3/WMA AUX Jack) . . . 182 — If Equipped ..... . 194 Operating Instructions - Radio Mode .
Page 155 UNDERSTANDING YOUR INSTRUMENT PANEL 153 Operation Instructions — CD Mode For CD uconnect studios (Satellite Radio) And MP3 Audio Play ....211 — If Equipped (REN/REQ/RER/RES Radios Only).
Page 156 154 UNDERSTANDING YOUR INSTRUMENT PANEL Kicker High Performance Sound System With Climate Controls ..... 230 Driver-Selectable Surround (DSS) Manual Air Conditioning And Heating –...
Page 157: Instrument Panel Features
UNDERSTANDING YOUR INSTRUMENT PANEL 155 INSTRUMENT PANEL FEATURES 1 - Air Outlets 5 - Heated Seat Switch 9 - Ignition Switch 2 - Instrument Cluster 6 - ESP OFF Switch 10 - Trunk Release Switch 3 - Glove Compartment 7 - Hazard Warning Switch 11 - Headlight Switch 4 - Radio 8 - Climate Control...
Page 158: Instrument Cluster - Base
156 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER – BASE...
Page 159: Instrument Cluster - Premium
UNDERSTANDING YOUR INSTRUMENT PANEL 157 INSTRUMENT CLUSTER – PREMIUM...
Page 160: Instrument Cluster Description
158 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION 5. Tachometer The red segments indicate the maximum permissible 1. Fuel Gauge engine revolutions per minute (RPM x 1000) for each gear The pointer shows the level of fuel in the fuel tank when range.
Page 161 UNDERSTANDING YOUR INSTRUMENT PANEL 159 7. Electronic Throttle Control (ETC) Warning Light Also, have the system checked by an authorized dealer if This light will turn on briefly as a bulb check the light does not come on during starting. when the ignition switch is turned ON.
Page 162 160 UNDERSTANDING YOUR INSTRUMENT PANEL 9. Turn Signal Indicators CAUTION! The arrow will flash with the exterior turn signal when the turn signal lever is operated. Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads NOTE: “H,”...
Page 163 UNDERSTANDING YOUR INSTRUMENT PANEL 161 11. Engine Temperature Warning Light 13. Electronic Stability Program (ESP) Indicator Light This light will turn on and a single chime will / Brake Assist System (BAS) Warning Light sound to warn of an overheated engine condition. The malfunction lamp for the Electronic Stabil- When this light turns on, the engine temperature ity Program (ESP) is combined with Brake...
Page 164 162 UNDERSTANDING YOUR INSTRUMENT PANEL 14. Oil Pressure Warning Light 16. Seat Belt Reminder Light This light indicates low engine oil pressure. The This light will turn on for five to eight seconds as light should turn on momentarily when the engine a bulb check when the ignition switch is first is started.
Page 165 UNDERSTANDING YOUR INSTRUMENT PANEL 163 19. Odometer/Electronic Vehicle Information Center Loose Fuel Filler Cap Message (EVIC) Display If the vehicle diagnostic system determines that the fuel The odometer shows the total distance the vehicle has filler cap is loose, improperly installed, or damaged, a been driven.
Page 166 164 UNDERSTANDING YOUR INSTRUMENT PANEL the next scheduled oil change interval. The engine oil NOTE: If the indicator message illuminates when you change indicator system is duty cycle based, which start the engine, the oil change indicator system did not means the engine oil change interval may fluctuate reset.
Page 167 UNDERSTANDING YOUR INSTRUMENT PANEL 165 the brake booster, the ABS pump will run when applying WARNING! the brake and a brake pedal pulsation may be felt during each stop. Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. The dual brake system provides a reserve braking capac- It will take longer to stop the vehicle.
Page 168 166 UNDERSTANDING YOUR INSTRUMENT PANEL The light also will turn on when the parking brake is vehicle placard or tire inflation pressure label, you should applied with the ignition switch in the ON position. determine the proper tire inflation pressure for those tires.) NOTE: This light shows only that the parking brake is applied.
Page 169 UNDERSTANDING YOUR INSTRUMENT PANEL 167 maintain correct tire pressure, even if under-inflation has tires or wheels on your vehicle, to ensure that the not reached the level to trigger illumination of the TPMS replacement or alternate tires and wheels allow the TPMS low tire pressure telltale.
Page 170 168 UNDERSTANDING YOUR INSTRUMENT PANEL 23. Anti-Lock Brake (ABS) Light 25. Malfunction Indicator Light (MIL) This light monitors the Anti-Lock Brake System The Malfunction Indicator Light (MIL) is part of (ABS). The light will turn on when the ignition an onboard diagnostic system called OBD. The switch is turned to the ON position and may stay on for OBD system monitors engine and automatic as long as four seconds.
Page 171: Electronic Vehicle Information Center (Evic)
UNDERSTANDING YOUR INSTRUMENT PANEL 169 26. Door Ajar Indicator This light will turn on to indicate that one or more door may be ajar. 27. Decklid Ajar Indicator This light will turn on to indicate that the decklid may be ajar.
Page 172 170 UNDERSTANDING YOUR INSTRUMENT PANEL • Vehicle Information Warning Message Displays MENU Button Press and release the MENU button and the • Tire Pressure Monitor System mode displayed will change between Trip • Personal Settings (Customer Programmable Features) Functions, Performance Pages, uconnect gps (If Equipped), System Warnings, System Sta- •...
Page 173: Electronic Vehicle Information Center (Evic) Displays
UNDERSTANDING YOUR INSTRUMENT PANEL 171 • Left Front Turn Signal Light Out (with a single chime) Features). The SCROLL button also functions as a remote sound system control. Refer to “Remote Sound System • Left Rear Turn Signal Light Out (with a single chime) Controls”...
Page 174: Engine Oil Change Indicator System
172 UNDERSTANDING YOUR INSTRUMENT PANEL • Channel # Trained • Wrong Key • Clearing Channels • Push Button or Insert Key/Turn To Run (refer to “Remote Starting System” in Section 2) • Channels Cleared • 1–4 SKIPSHIFT • Did Not Train •...
Page 175: Trip Functions
UNDERSTANDING YOUR INSTRUMENT PANEL 173 indicator system is duty cycle based, which means the Trip Functions engine oil change interval may fluctuate, dependent Press and release the MENU button until one of the upon your personal driving style. following Trip Functions displays in the EVIC: •...
Page 176 174 UNDERSTANDING YOUR INSTRUMENT PANEL “RESET” or show dashes for two seconds. Then, the significant amount of fuel to the vehicle will turn off the history information will be erased, and the averaging will LOW FUEL text and a new DTE value will display. continue from the last fuel average reading before the •...
Page 177: Keyless Go Display - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 175 To Reset The Display Reset will only occur while a resettable function is being displayed. Press and release the FUNCTION SELECT button once to clear the resettable function being dis- played. To reset all resettable functions, press and release the FUNCTION SELECT button a second time within three seconds of resetting the currently-displayed func- tion.
Page 178: Compass Display
176 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Under certain conditions, the display may be objects) until the “CAL” message displayed in the EVIC superseded by another display of higher priority. But turns off. The compass will now function normally. when the ignition switch position is changed, the display Manual Compass Calibration always re-appears.
Page 179 UNDERSTANDING YOUR INSTRUMENT PANEL 177 5. Complete one or more 360 degree turns (in an area free from large metal or metallic objects) until the “CAL” message turns off. The compass will now function normally. Compass Variance Compass Variance is the difference between magnetic North and geographic North.
Page 180: Driver-Selectable Surround Sound (Dss) - If Equipped
178 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Press the SCROLL button until “Compass Variance” System Warnings (Customer Information message and the last variance zone number displays in Features) the EVIC. Press and release the MENU button until “SYSTEM WARNINGS” displays in the EVIC. Then, press the 4.
Page 181 UNDERSTANDING YOUR INSTRUMENT PANEL 179 Press and release the MENU button until Personal Set- Lock Doors Automatically at 15 mph (24 km/h) tings displays in the EVIC. When ON is selected, both doors will lock automatically when the vehicle reaches a speed of 15 mph (24 km/h). Use the SCROLL button to display one of the following To make your selection, press and release the FUNC- choices.
Page 182 180 UNDERSTANDING YOUR INSTRUMENT PANEL the doors will unlock on the first press of the RKE Headlamps On with Wipers (Available with Auto transmitter UNLOCK button. To make your selection, Headlights Only) press and release the FUNCTION SELECT button until When ON is selected, and the headlight switch is in the “Driver Door 1st Press”...
Page 183 UNDERSTANDING YOUR INSTRUMENT PANEL 181 Hill Start Assist (HSA) — If Equipped ignition switch is turned OFF. Opening a vehicle door When on is selected, the HSA system is active. Refer to will cancel this feature. To make your selection, press and “HSA (Hill Start Assistance)”...
Page 184: Sales Code Req - Am/Fm Stereo Radio And 6-Disc Cd Changer (Mp3/Wma Aux Jack)
182 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE REQ — AM/FM STEREO RADIO Operating Instructions - Radio Mode AND 6–DISC CD CHANGER (MP3/WMA AUX NOTE: The ignition switch must be in the ON or ACC JACK) position to operate the radio. NOTE: The radio sales code is located on the lower right Power Switch/Volume Control (Rotary) side of the radio faceplate.
Page 185 UNDERSTANDING YOUR INSTRUMENT PANEL 183 to seek up and the left switch to seek down. The radio Phone Button uconnect phone — If Equipped will remain tuned to the new station until you make Press this button to operate the uconnect phone feature another selection.
Page 186 184 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Adjust the minutes using the right side TUNE/ TUNE Control SCROLL control knob. Press the TUNE/SCROLL control Turn the rotary TUNE/SCROLL control knob clockwise knob to save the time change. to increase or counterclockwise to decrease the frequency. 5.
Page 187 UNDERSTANDING YOUR INSTRUMENT PANEL 185 SCROLL control knob to the right or left to adjust the 16-Digit Character Dis- Program Type sound level from the right or left side speakers. play No program type or un- Push the rotary TUNE/SCROLL control knob a fifth time None defined and FADE will display.
Page 188 186 UNDERSTANDING YOUR INSTRUMENT PANEL station with the same selected Music Type name. The 16-Digit Character Dis- Program Type Music Type function only operates when in the FM play mode. Rhythm and Blues R & B Religious Music Rel Musc If a preset button is activated while in the Music Type (Program Type) mode, the Music Type mode will be Religious Talk...
Page 189: Operation Instructions - (Disc Mode For Cd And Mp3/Wma Audio Play)
UNDERSTANDING YOUR INSTRUMENT PANEL 187 You may add a second station to each pushbutton by Operation Instructions - (DISC MODE for CD and repeating the above procedure with this exception: Press MP3/WMA Audio Play) the SET button twice and SET 2 will show in the display NOTE: The ignition switch must be in the ON or ACC window.
Page 190 188 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Button (CD MODE) CAUTION! Press the right SEEK button for the next selection on the CD. Press the left SEEK button to return to the beginning This CD player will accept 4–3/4 in (12 cm) discs only. of the current selection, or return to the beginning of the The use of other sized discs may damage the CD previous selection if the CD is within the first second of...
Page 191: Notes On Playing Mp3/Wma Files
UNDERSTANDING YOUR INSTRUMENT PANEL 189 RW/FF (CD MODE) Supported Medium Formats (File Systems) Press and hold FF (Fast Forward) and the CD player will The medium formats supported by the radio are ISO 9660 begin to fast forward until FF is released, or RW or Level 1 and Level 2 and includes the Joliet extension.
Page 192 190 UNDERSTANDING YOUR INSTRUMENT PANEL Multisession disc formats are supported by the radio. frequencies in the following table are supported. In Multisession discs may contain combinations of normal addition, variable bit rates (VBR) are also supported. The CD audio tracks and computer files (including MP3/ majority of MP3/WMA files use a 44.1 kHz sampling rate WMA files).
Page 193: List Button (Disc Mode For Mp3/Wma Play)
UNDERSTANDING YOUR INSTRUMENT PANEL 191 • Number of files and folders - Loading times will ID3 Tag information for artist, song title, and album title are supported for ID3 version 1 tags. ID3 version 2 is not increase with more files and folders supported by the radios.
Page 194: Info Button (Disc Mode For Mp3/Wma Play)
192 UNDERSTANDING YOUR INSTRUMENT PANEL INFO Button (DISC Mode for MP3/WMA Play) Pressing the AUX button will change the mode to auxil- Pressing the INFO button repeatedly will scroll through iary device if the AUX jack is connected. the following TAG information: Song Title, Artist, File NOTE: The AUX device must be turned on and the Name, and Folder Name (if available).
Page 195 UNDERSTANDING YOUR INSTRUMENT PANEL 193 TIME Button (Auxiliary Mode) Operating Instructions - uconnect studios Press the TIME button to change the display from (Satellite Radio) (If Equipped) elapsed playing time to time of day. The time of day will Refer to “uconnect studios (Satellite Radio)”...
Page 196: Am/Fm/Cd/Dvd Radio (Rer/Ren)
194 UNDERSTANDING YOUR INSTRUMENT PANEL DTS™ Operating Instructions — Voice Recognition DTS™ and DTS™ 2.0 are trademarks of Digital The- System (VR) — If Equipped ater Systems, Inc. For the radio, refer to “Voice Recognition System (VR)” in Section 3. AM/FM/CD/DVD RADIO (RER/REN) –...
Page 197 UNDERSTANDING YOUR INSTRUMENT PANEL 195 To Manually Set the Clock — RER/REN 6. To save the new time setting, touch the screen where the word “Save” is displayed. 1. Turn on the radio. Changing Daylight Savings Time 2. Touch the screen where the time is displayed. When selected, this feature will display the time of day in 3.
Page 198 196 UNDERSTANDING YOUR INSTRUMENT PANEL Show Time if Radio is Off 2. Touch the screen where the time is displayed. The When selected, this feature will display the time of day clock setting menu will appear on the screen. on the touch screen when the radio is turned off. Proceed 3.
Page 199: Sales Code Res - Am/Fm Stereo Radio With Cd Player (Mp3 Aux Jack)
UNDERSTANDING YOUR INSTRUMENT PANEL 197 SALES CODE RES — AM/FM STEREO RADIO Operating Instructions — Radio Mode WITH CD PLAYER (MP3 AUX JACK) NOTE: The ignition switch must be in the ON or ACC NOTE: The radio sales code is located on the lower right position to operate the radio.
Page 200 198 UNDERSTANDING YOUR INSTRUMENT PANEL to seek up and the left switch to seek down. The radio 4. Adjust the minutes using the right side TUNE/ will remain tuned to the new station until you make SCROLL control knob. Press the TUNE/SCROLL control another selection.
Page 201 UNDERSTANDING YOUR INSTRUMENT PANEL 199 Push the rotary TUNE/SCROLL control knob a second Push the rotary TUNE/SCROLL control knob again to time and MID will display. Turn the TUNE/SCROLL exit setting tone, balance, and fade. control knob to the right or left to increase or decrease the AM/FM Button mid-range tones.
Page 202: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
200 UNDERSTANDING YOUR INSTRUMENT PANEL SET 2 in both AM and FM. This allows a total of 12 AM Operation Instructions — CD MODE For CD And and 12 FM stations to be stored into pushbutton memory. MP3 Audio Play The stations stored in SET 2 memory can be selected by NOTE: pressing the pushbutton twice.
Page 203 UNDERSTANDING YOUR INSTRUMENT PANEL 201 If you insert a disc with the ignition ON and the radio EJECT Button - Ejecting a CD ON, the unit will switch from radio to CD mode and Press the EJECT button to eject the CD. begin to play when you insert the disc.
Page 204: Notes On Playing Mp3 Files
202 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button Press the RND button a second time to stop Random Press this button to change the display from a large CD Play. playing time display to a small CD playing time display. Notes on Playing MP3 Files RW/FF The radio can play MP3 files;...
Page 205 UNDERSTANDING YOUR INSTRUMENT PANEL 203 The radio uses the following limits for file systems: Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal • Maximum number of folder levels: 8 CD audio tracks and computer files (including MP3 files). •...
Page 206 204 UNDERSTANDING YOUR INSTRUMENT PANEL rates (VBR) are also supported. The majority of MP3 files Playback of MP3 Files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or When a medium containing MP3 data is loaded, the VBR bit rate.
Page 207: Operation Instructions - Auxiliary Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 205 Operation Instructions - Auxiliary Mode SALES CODE RES/RSC — AM/FM STEREO The auxiliary (AUX) jack is an audio input jack, which RADIO WITH CD PLAYER (MP3 AUX JACK) AND allows the user to plug in a portable device, such as an SIRIUS RADIO MP3 player, or cassette player, and utilize the vehicle’s NOTE: The radio sales code is located on the lower right...
Page 208: Operating Instructions - Radio Mode
206 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Radio Mode to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make NOTE: The ignition switch must be in the ON or ACC another selection.
Page 209 UNDERSTANDING YOUR INSTRUMENT PANEL 207 If your vehicle is not equipped with or this feature is not 5. To exit, press any button/knob or wait five seconds. available on your vehicle, a “Not Equipped With The clock can also be set by pressing the SETUP button. uconnect”...
Page 210 208 UNDERSTANDING YOUR INSTRUMENT PANEL TUNE Control SCROLL control knob to the right or left to adjust the Turn the rotary TUNE/SCROLL control knob clockwise sound level from the right or left side speakers. to increase or counterclockwise to decrease the frequency. Push the rotary TUNE/SCROLL control knob a fifth time Setting the Tone, Balance, and Fade and FADE will display.
Page 211 UNDERSTANDING YOUR INSTRUMENT PANEL 209 16-Digit Character Dis- 16-Digit Character Dis- Program Type Program Type play play No program type or un- Rhythm and Blues R & B None defined Religious Music Rel Musc Adult Hits Adlt Hit Religious Talk Rel Talk Classical Classicl...
Page 212 210 UNDERSTANDING YOUR INSTRUMENT PANEL station with the same selected Music Type name. The SET/RND Button — To Set the Pushbutton Music Type function only operates when in the FM Memory mode. When you are receiving a station that you wish to commit to pushbutton memory, press the SET/RND If a preset button is activated while in the Music Type button.
Page 213: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
UNDERSTANDING YOUR INSTRUMENT PANEL 211 • This radio is capable of playing compact discs (CD), Every time a preset button is used, a corresponding button number will display. recordable compact discs (CD-R), rewritable compact discs (CD-RW), compact discs with MP3 tracks and Buttons 1 - 6 multisession compact discs with CD and MP3 tracks.
Page 214 212 UNDERSTANDING YOUR INSTRUMENT PANEL If you have ejected a disc and have not removed it within CAUTION! 10 seconds, it will be reloaded. If the CD is not removed, • This CD player will accept 4–3/4 in (12 cm) discs the radio will reinsert the CD but will not play it.
Page 215: Notes On Playing Mp3 Files
UNDERSTANDING YOUR INSTRUMENT PANEL 213 RW/FF Notes On Playing MP3 Files Press and hold FF (Fast Forward) and the CD player will The radio can play MP3 files; however, acceptable MP3 begin to fast forward until FF is released or RW or file recording media and formats are limited.
Page 216 214 UNDERSTANDING YOUR INSTRUMENT PANEL • Maximum number of files: 255 Discs created with an option such as keep disc open after writing are most likely multisession discs. The use of • Maximum number of folders. (The radio display of file multisession for CD audio or MP3 playback may result in names and folder names is limited.
Page 217 UNDERSTANDING YOUR INSTRUMENT PANEL 215 Playback of MP3 Files MPEG Specifi- Sampling Fre- Bit Rate (kbps) When a medium containing MP3 data is loaded, the cation quency (kHz) radio checks all files on the medium. If the medium 320, 256, 224, contains a lot of folders or files, the radio will take more MPEG-1 Audio 192, 160, 128,...
Page 218: List Button (Cd Mode For Mp3 Play)
216 UNDERSTANDING YOUR INSTRUMENT PANEL LIST Button (CD Mode for MP3 Play) Press and hold the INFO button again for three seconds Pressing the LIST button will bring up a list of all folders to return to elapsed time display. on the disc.
Page 219: Universal Consumer Interface (Uci) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 217 TIME Button (Auxiliary Mode) to the separate RER, REN or REZ User’s Manual. UCI is Press this button to change the display to time of day. The available only if equipped as an option with these radios. time of day will display for five seconds (when the This feature allows you to plug an iPod into the...
Page 220: Connecting The Ipod
218 UNDERSTANDING YOUR INSTRUMENT PANEL Connecting The iPod Using This Feature Use the optional connection cable to connect an iPod to By using the optional connection cable to connect an the vehicle’s 16–pin connector port located on the center iPod to the vehicle’s UCI 16–pin connector port: console.
Page 221: Play Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 219 • Jump backward in the current track by pressing and Play Mode When switched to UCI mode, the iPod automatically holding the << RW button. Holding the << RW starts Play mode. In Play mode, you may use the button long enough will take you to the beginning following buttons on the radio faceplate to control the of the current track.
Page 222: List Or Browse Mode
220 UNDERSTANDING YOUR INSTRUMENT PANEL • While a track is playing, press the INFO button to see Shuffle OFF modes for the iPod . If the RND icon is the associated metadata (Artist, track title, album, etc.) showing on the radio display, then the shuffle mode is for that track.
Page 223 UNDERSTANDING YOUR INSTRUMENT PANEL 221 • During all List modes, the iPod displays all lists in • To Exit List mode without selecting a track, press the “wrap-around” mode. So if the track is at the same PRESET button again to go back to Play bottom of the list just turn the wheel backwards mode.
Page 224: Uconnect Studios (Satellite Radio) - If Equipped (Ren/Req/Rer/Res Radios Only)
222 UNDERSTANDING YOUR INSTRUMENT PANEL uconnect studios (SATELLITE RADIO) — IF CAUTION! EQUIPPED (REN/REQ/RER/RES RADIOS ONLY) • Leaving the iPod (or any supported device) any- Satellite radio uses direct satellite-to-receiver broadcast- ing technology to provide clear digital sound, coast to where in the vehicle in extreme heat or cold can coast.
Page 225: Electronic Serial Number/Sirius Identification Number (Esn/Sid)
UNDERSTANDING YOUR INSTRUMENT PANEL 223 number 888-539-7474, or visit the Sirius web site at Sirius ID number will display. The Sirius ID number www.sirius.com, or at www.siriuscanada.ca for Cana- display will time out in two minutes. Press any button on dian residents.
Page 226: Reception Quality
224 UNDERSTANDING YOUR INSTRUMENT PANEL bikes should be placed as far rearward as possible, within Operating Instructions - uconnect studios the loading design of the rack. Do not place items directly (Satellite) Mode on or above the antenna. NOTE: The ignition switch must be in the ON or ACC Reception Quality position to operate the radio.
Page 227 UNDERSTANDING YOUR INSTRUMENT PANEL 225 INFO Button or turning the Tune/Scroll control knob within five Pressing the INFO button will cycle the display informa- seconds will allow the program format type to be se- tion between Artist, Song Title, and Composer (if avail- lected.
Page 228: Operating Instructions - Uconnect Phone (If Equipped)
226 UNDERSTANDING YOUR INSTRUMENT PANEL • Display Sirius ID number — Press the AUDIO/ the SET button twice and SET 2 will show in the display SELECT button to display the Sirius ID number. This window. Each button can be set for SET 1 and SET 2. This number is used to activate, deactivate, or change the allows a total of 12 Satellite channels to be stored into Sirius subscription.
Page 229: Kicker High Performance Sound System With Driver-Selectable Surround (Dss) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 227 KICKER HIGH PERFORMANCE SOUND SYSTEM any stereo audio source. A new feature of the Kicker WITH DRIVER-SELECTABLE SURROUND (DSS) – audio system offers the ability to choose surround sound for any audio source. IF EQUIPPED “Audio Surround”...
Page 230: Remote Sound System Controls
228 UNDERSTANDING YOUR INSTRUMENT PANEL When in “Audio Surround” mode, balance is set auto- The remote sound system controls are located on the matically. Fader control is available to add more sur- surface of the steering wheel at the three and nine o’clock round audio if desired.
Page 231: Cd/Dvd Disc Maintenance
UNDERSTANDING YOUR INSTRUMENT PANEL 229 If the Compass/Temp/Audio screen is already displayed CD/DVD DISC MAINTENANCE when the AUDIO MODE button is pressed, then the To keep a CD/DVD in good condition, take the following mode will change (i.e., from AM to FM, to Media mode, precautions: etc., depending on which radio is in the vehicle).
Page 232: Radio Operation And Cellular Phones
230 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particu- CLIMATE CONTROLS lar disc, it may be damaged (i.e. scratched, reflective Manual Air Conditioning and Heating System coating removed, a hair, moisture or dew on the disc) oversized, or have copyright encoding.
Page 233 UNDERSTANDING YOUR INSTRUMENT PANEL 231 Blower Control Temperature Control Use this control to regulate the Use this control to regulate the tem- amount of air forced through the ven- perature of the air inside the passenger tilation system in any mode. The compartment.
Page 234 232 UNDERSTANDING YOUR INSTRUMENT PANEL • Bi-Level Mode Control Use this control to choose from several Air is directed through the instrument panel, center patterns of air distribution. You can console and floor outlets. select either a primary mode as iden- NOTE: For all settings except full cold or full hot, there tified by the symbols on the control, or is a difference in temperature between the upper and...
Page 235 UNDERSTANDING YOUR INSTRUMENT PANEL 233 • Mix • Recirculation Control Air is directed through the floor, defrost, and side Use this button to block the flow of outside air window demist outlets. This setting works best in from coming into the passenger compartment. cold or snowy conditions that require extra heat to A light will illuminate when the system is in the windshield.
Page 236 234 UNDERSTANDING YOUR INSTRUMENT PANEL • The A/C will engage automatically to prevent fogging • Economy Mode when the recirculation button is pressed. If economy mode is desired, press the A/C button to turn off the indicator light and the A/C compressor. Then, •...
Page 237: Operating Tips
UNDERSTANDING YOUR INSTRUMENT PANEL 235 If Outside Ambient Mode Overrides To Temperature Overrides To Rear Window Defroster Temperature Is Active Less than 40°F Full Heat Between 40°F and 80°F No Override No Override More than 80°F Bi-Level Full Cool NOTE: to provide proper corrosion protection and to protect •...
Page 238: Maintenance Schedules
236 UNDERSTANDING YOUR INSTRUMENT PANEL fresh air and high blower settings. This will ensure Floor, Mix, or Defrost mode. The air is directed at the area adequate system lubrication to minimize the possibility of the windows through which you view the outside of compressor damage when the system is started again.
Page 239 UNDERSTANDING YOUR INSTRUMENT PANEL 237 Control Setting Suggestions for Various Weather Conditions...
Page 241 STARTING AND OPERATING CONTENTS Starting Procedures ....243 Engine Block Heater — If Equipped ..251 Manual Transmission .
Page 242 240 STARTING AND OPERATING 5-Speed Automatic Transmission (5.7L Manual Transmission — If Equipped ..276 Engine) ......265 Automatic Transmission —...
Page 243 STARTING AND OPERATING 241 Synchronizing ESP ....287 Life Of Tire ..... . . 303 ESP/BAS Malfunction Indicator Light And Replacement Tires .
Page 244 242 STARTING AND OPERATING Reformulated Gasoline ....317 Gross Axle Weight Rating (GAWR) ..324 Gasoline/Oxygenate Blends ... 317 Overloading .
Page 245: Starting Procedures
STARTING AND OPERATING 243 STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust the • Be sure to turn OFF the engine and remove the key inside and outside mirrors, fasten your seat belt, and if from the ignition switch if you want to rest or present, instruct all other occupants to buckle their seat sleep in your car.
Page 246 244 STARTING AND OPERATING Normal Starting with Integrated Key — Manual WARNING! Transmission Normal starting of either a cold or a warm engine does Do not attempt to push or tow your vehicle to get it not require pumping or depressing the accelerator pedal. started.
Page 247: Automatic Transmission
STARTING AND OPERATING 245 Automatic Transmission Using Fob With Integrated Key (Tip Start) The shift lever must be in the NEUTRAL or PARK NOTE: Normal starting of either a cold or a warm position before you can start the engine. Apply the brakes engine is obtained without pumping or depressing the before shifting into any driving gear.
Page 248: Keyless Go
246 STARTING AND OPERATING Keyless Go Removing the Button This feature allows the driver to oper- 1. The ENGINE START/STOP button can be removed ate the ignition switch with the push from the ignition switch for regular ignition key use. of a button, as long as the ENGINE START/STOP button is installed and 2.
Page 249 STARTING AND OPERATING 247 To start the engine, the transmission must be in PARK or To Turn Off the Engine Using ENGINE NEUTRAL. Press and hold the brake pedal while press- START/STOP Button — Automatic Transmission ing the ENGINE START/STOP button once. The system Only takes over and attempts to start the vehicle.
Page 250 248 STARTING AND OPERATING NOTE: If the ignition switch is left in the ACC position NOTE: • If the ignition switch is left in the ACC position the the system will automatically time out after 60 minutes of inactivity and the ignition will switch to the OFF system will automatically time out after 60 minutes of position.
Page 251: Extremely Cold Weather (Below 20°F Or 29°C)
STARTING AND OPERATING 249 START. To change the ignition switch positions without Extremely Cold Weather (Below 20°F or 29°C) starting the vehicle and use the accessories follow these To ensure reliable starting at these temperatures, use of steps. an externally powered electric engine block heater (avail- able from your authorized dealer) is recommended.
Page 252 250 STARTING AND OPERATING Clearing a Flooded Engine (Using ENGINE WARNING! (Continued) START/STOP Button) — Automatic Transmission • Do not attempt to push or tow your vehicle to get Only it started. Vehicles equipped with an automatic If the engine fails to start after you have followed the transmission cannot be started this way.
Page 253: After Starting
STARTING AND OPERATING 251 and hold the clutch pedal, push the accelerator pedal all CAUTION! the way to the floor and hold it, then press and hold the ENGINE START/STOP button for no more than 15 sec- To prevent damage to the starter, wait 10 to 15 sec- onds.
Page 254: Manual Transmission - If Equipped
252 STARTING AND OPERATING WARNING! CAUTION! • Never drive with your foot resting on the clutch Remember to disconnect the cord before driving. Damage to the 110-115 Volt electrical cord could cause pedal, or try to hold the vehicle on a hill with the electrocution.
Page 255 STARTING AND OPERATING 253 spring helps you know which gear you are in when you are shifting. Be careful when shifting from first to second or downshifting from sixth to fifth. The spring will try to pull the shift lever toward third and fourth gear.
Page 256 254 STARTING AND OPERATING Recommended Shift Speeds NOTE: • Your vehicle is equipped with a transmission reverse To utilize your manual transmission efficiently for fuel economy, it should be upshifted as listed in recom- inhibitor system. When vehicle speed is greater than mended shift speed chart.
Page 257 STARTING AND OPERATING 255 1–4 Skip Shift Downshifting There are times when you must shift the transmission To maintain a safe speed and prolong brake life, down- directly from first gear to fourth gear instead of from first shift to maintain a safe speed when descending a steep gear to second gear.
Page 258: Automatic Transmission - If Equipped
256 STARTING AND OPERATING AUTOMATIC TRANSMISSION — IF EQUIPPED WARNING! CAUTION! It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle Damage to the automatic transmission may occur if speed.
Page 259 STARTING AND OPERATING 257 • Shift lever position • The electronically-controlled transmission provides a precise shift schedule. The transmission electronics are • Accelerator position self-calibrating. Therefore, the first few shifts on a new • Vehicle speed vehicle may be somewhat abrupt or soft until after the break-in period.
Page 260: Brake/Transmission Shift Interlock System
258 STARTING AND OPERATING This may result in a slightly different feeling or response WARNING! during normal operation in DRIVE position. After the transmission cools down, it will return to normal Unintended movement of a vehicle could injure operation. those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is Brake/Transmission Shift Interlock System running.
Page 261 STARTING AND OPERATING 259 pressing the override tab, move the shift lever out of the PARK position. When complete, return the override cover to its original position. With Keyless Go — If Equipped To activate the override, with a valid keyfob (FOBIK) inside of the vehicle, and without the brake pedal pressed, press the START/STOP button once to go to the ACC position, or twice to go to the ON position.
Page 262: 4-Speed Automatic Transmission (3.5L Engine)
260 STARTING AND OPERATING 4-Speed Automatic Transmission (3.5L Engine) NOTE: Under extreme cold temperatures (-6°F (-21°C) and when in DRIVE, transmission operation may be briefly limited to only 2nd gear operation. Normal op- eration will resume once the transmission temperature has risen to a suitable level.
Page 263 STARTING AND OPERATING 261 When parking on a flat surface, place the shift lever in the The following indicators should be used to ensure that PARK position first, and then apply the parking brake. you have engaged the shift lever in the PARK position: •...
Page 264 262 STARTING AND OPERATING NEUTRAL shifts and the best fuel economy. Select the “3” range The engine may be started in this range. when frequent transmission shifting occurs when using the Overdrive range, such as when operating the vehicle CAUTION! under heavy loading conditions (in hilly terrain, travel- ing into strong head winds, or while towing heavy Coasting the vehicle or driving for any other reason...
Page 265 STARTING AND OPERATING 263 “3” (Third) CAUTION! This range eliminates shifts into Overdrive. The transmis- sion will operate normally in 1st, 2nd, and 3rd while in Never race the engine with the brakes on and the this range. The “3” position should also be used when vehicle in gear, and never hold the vehicle on an descending steep grades to prevent brake system dis- incline without applying the brakes.
Page 266 264 STARTING AND OPERATING NOTE: Transmission Limp Home Mode • The torque converter clutch will not engage until the The transmission is monitored for abnormal conditions. transmission fluid and engine coolant is warm (usu- If a condition is detected that could cause damage, the ally after 1–3 miles [1.6–4.8 km] of driving).
Page 267: Starting And Operating 265
STARTING AND OPERATING 265 possible convenience. Your authorized dealer has diag- nostic equipment to determine if the problem could recur. If the transmission cannot be reset, authorized dealer service is required. 5-Speed Automatic Transmission (5.7L Engine) Shifting from DRIVE to PARK or REVERSE should be done only after the accelerator pedal is released and the vehicle is stopped.
Page 268 266 STARTING AND OPERATING When parking on a flat surface, place the shift lever in the The following indicators should be used to ensure that PARK position first, and then apply the parking brake. you have engaged the shift lever in the PARK position: •...
Page 269 STARTING AND OPERATING 267 NEUTRAL WARNING! In NEUTRAL, no power is transmitted from the engine to the drive axle. When the brakes are released, the vehicle Do not coast in NEUTRAL and never turn off the can be moved freely (pushed or towed). Do not engage ignition to coast down a hill.
Page 270 268 STARTING AND OPERATING under heavy loading conditions (in hilly terrain, travel- brought to a stop. After the vehicle has stopped, PARK, ing into strong head winds, or while towing heavy REVERSE, and NEUTRAL will continue to operate. Sec- trailers, use the AutoStick mode and select the “3”...
Page 271: Autostick - If Equipped
STARTING AND OPERATING 269 NOTE: Even if the transmission can be reset, we recom- can also provide you with more control during passing, mend that you visit your authorized dealer at your city driving, cold slippery conditions, mountain driving, earliest possible convenience. Your authorized dealer has trailer towing, and many other situations.
Page 272: Autostick - 5.7L Engine
270 STARTING AND OPERATING Autostick — 5.7L Engine NOTE: In Autostick mode, the transmission will only Autostick is a driver-interactive transmission that offers shift up or down when the driver moves the shift lever to manual gear shifting to provide you with more control of the right (D+) or left (D-).
Page 273: Driving On Slippery Surfaces
STARTING AND OPERATING 271 • Starting out in second gear is helpful in snowy or icy WARNING! conditions. Rapid acceleration on slippery surfaces is dangerous. • Avoid using speed control when Autostick is en- Unequal traction can cause sudden pulling of the rear gaged.
Page 274: Driving Through Water
272 STARTING AND OPERATING 2. Slow down if the road has standing water or puddles. Flowing/Rising Water 3. Replace tires when tread wear indicators first become WARNING! visible. Do not drive on, or cross, a road or a path where 4.
Page 275 STARTING AND OPERATING 273 CAUTION! CAUTION! (Continued) • Driving through standing water may cause dam- • Always check the depth of the standing water age to your vehicle’s drivetrain components. Al- before driving through it. Never drive through ways inspect your vehicle’s fluids (i.e., engine oil, standing water that is deeper than the bottom of transmission, axle, etc.) for signs of contamination the tire rims mounted on the vehicle.
Page 276: Power Steering
274 STARTING AND OPERATING POWER STEERING WARNING! The standard power steering system will give you good • Driving through standing water limits your vehi- vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical cle’s traction capabilities. Do not exceed 5 mph steering capability if power assist is lost.
Page 277: Power Steering Fluid Check
STARTING AND OPERATING 275 apparent, and/or the system is not functioning as antici- WARNING! pated. Coordinate inspection efforts through an autho- rized dealer. Continued operation with reduced power steering assist could pose a safety risk to yourself and others. No chemical flushes should be used in any power Service should be obtained as soon as possible.
Page 278: Parking Brake
276 STARTING AND OPERATING PARKING BRAKE Manual Transmission — If Equipped The parking brake should always be applied when the The foot operated parking brake is positioned below the driver is not in the vehicle. lower left corner of the instrument panel. To release the parking brake, pull the parking brake release handle.
Page 279: Automatic Transmission - If Equipped
STARTING AND OPERATING 277 Automatic Transmission — If Equipped The foot operated parking brake is positioned below the lower left corner of the instrument panel. To apply the parking brake, push the parking brake pedal down and then remove your foot from the pedal. To release the parking brake, push down on the parking brake pedal and then release.
Page 280: Brake System
278 STARTING AND OPERATING pedal force required to slow or stop, and potential WARNING! activation of the Brake Warning Light. • Never leave children alone in a vehicle. Leaving In the event power assist is lost for any reason (for unattended children in a vehicle is dangerous for a example, repeated brake applications with the engine number of reasons.
Page 281 STARTING AND OPERATING 279 • A slight drop or fall away of the brake pedal at the end When the vehicle is driven over 7 mph (11 km/h), you may also hear a slight clicking sound as well as some of the stop.
Page 282 280 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Pumping of the Anti-Lock Brakes will diminish • The capabilities of an Anti-Lock Brake System their effectiveness and may lead to an accident. (ABS) equipped vehicle must never be exploited Pumping makes the stopping distance longer. Just in a reckless or dangerous manner, that could press firmly on your brake pedal when you need jeopardize the user’s safety or the safety of others.
Page 283: Electronic Brake Control System
STARTING AND OPERATING 281 the conventional brake system will continue to operate An additional electronic brake control feature called Hill normally if the Brake Warning Light is not on. Start Assist (HSA) is standard on manual transmission models. If the ABS Light is on, the brake system should be serviced as soon as possible to restore the benefits of ABS (Anti-Lock Brake System) —...
Page 284: Tcs (Traction Control System) - If Equipped
282 STARTING AND OPERATING A feature of the TCS system functions similar to a WARNING! limited-slip differential and controls the wheel spin across a driven axle. If one wheel on a driven axle is The ABS cannot prevent the natural laws of physics spinning faster than the other, the system will apply the from acting on the vehicle, nor can it increase the brake of the spinning wheel.
Page 285: Hsa (Hill Start Assist) - Manual Transmission Only
STARTING AND OPERATING 283 must apply continuous brake pedal pressure during the HSA (Hill Start Assist) — Manual Transmission stopping sequence. Do not reduce brake pedal pressure Only unless braking is no longer desired. Once the brake pedal The HSA system is designed to assist the driver when is released, the BAS is deactivated.
Page 286 284 STARTING AND OPERATING • Gear selection matches vehicle uphill direction (i.e., For vehicles not equipped with the EVIC, perform the vehicle facing uphill is in forward gear; vehicle back- following steps: ing uphill is in REVERSE gear). NOTE: You must complete Steps 1 through 8 within 90 seconds.
Page 287: Esp (Electronic Stability Program) - If Equipped
STARTING AND OPERATING 285 8. Rotate the steering wheel back to center and then an The ESP uses sensors in the vehicle to determine the path additional half-turn to the right. that the driver intends to steer the vehicle and compares it to the actual path of the vehicle.
Page 288 286 STARTING AND OPERATING accelerator and apply as little throttle as possible. Be sure ESP On to adapt your speed and driving to the prevailing road This is the normal operating mode for the ESP. Whenever conditions. the vehicle is started, the ESP system will be in this mode. This mode should be used for most driving situations.
Page 289: Synchronizing Esp
STARTING AND OPERATING 287 To turn the ESP ON again, momentarily depress the ESP “Partial Off” mode by momentarily depressing the ESP OFF switch and the ESP/TCS Indicator Light will turn OFF switch. Once the situation requiring “Partial Off” off. mode is overcome, turn the ESP ON again by momen- tarily depressing the ESP OFF switch.
Page 290: Esp/Bas Malfunction Indicator Light And Esp/Tcs Indicator Light
288 STARTING AND OPERATING ESP/BAS Malfunction Indicator Light and NOTE: • The ESP/TCS Indicator Light and the ESP/BAS Mal- ESP/TCS Indicator Light The Malfunction Indicator Light for the ESP is function Indicator Light will turn on momentarily combined with the BAS indicator. The yellow each time the ignition switch is turned ON.
Page 291: Tire Safety Information
STARTING AND OPERATING 289 TIRE SAFETY INFORMATION NOTE: • P (Passenger) - Metric tire sizing is based on U.S. Tire Markings design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. •...
Page 292 290 STARTING AND OPERATING CAUTION! Do not use two different size tires on the rear wheels, as this can result in rear axle damage. Tire Sizing Chart TIRE SIZING TERMS Size Designation: P = Passenger Car tire size based on U.S. design standards ..blank..
Page 293 STARTING AND OPERATING 291 TIRE SIZING TERMS R = Construction code — R means radial construction — D means diagonal or bias construction 15 = Rim diameter in inches (in) Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol —...
Page 294 292 STARTING AND OPERATING TIRE SIZING TERMS Light Load = Light load tire C, D, E = Load range associated with the maximum load a tire can carry at a specified pressure Maximum Load — Maximum load indicates the maximum load this tire is designed to carry Maximum Pressure —...
Page 295 STARTING AND OPERATING 293 TIRE IDENTIFICATION NUMBER EXAMPLE: DOT MA L9 ABCD 0301 MA = Code representing the tire manufacturing location (two digits) L9 = Code representing the tire size (two digits) ABCD = Code used by the tire manufacturer (one to four digits) 03 = Number representing the week in which the tire was manufactured (two digits) —03 means the 3rd week.
Page 296: Tire Loading And Tire Pressure
294 STARTING AND OPERATING Tire Loading and Tire Pressure This placard tells you important information about the: Tire Placard Location 1) number of people that can be carried in the vehicle NOTE: The proper cold tire inflation pressure is listed 2) total weight your vehicle can carry on the driver’s side B-Pillar.
Page 297 STARTING AND OPERATING 295 axles must not be exceeded. For further information on 3. Subtract the combined weight of the driver and pas- GAWRs, vehicle loading, and trailer towing, refer to sengers from XXX kg or XXX lbs. “Vehicle Loading” in this section. 4.
Page 298: Tires - General Information
296 STARTING AND OPERATING NOTE: TIRES — GENERAL INFORMATION • The following table shows examples on how to calcu- Tire Pressure late total load, cargo/luggage, and towing capacities Proper tire inflation pressure is essential to the safe and of your vehicle with varying seating configurations satisfactory operation of your vehicle.
Page 299 STARTING AND OPERATING 297...
Page 300: Tire Inflation Pressures
298 STARTING AND OPERATING earlier tire replacement. Under-inflation also increases WARNING! (Continued) tire rolling resistance and results in higher fuel • Unequal tire pressures can cause steering prob- consumption. lems. You could lose control of your vehicle. Ride Comfort and Vehicle Stability •...
Page 301 STARTING AND OPERATING 299 once a month. Use a good quality pocket-type gauge to Check tire pressures more often if subject to a wide range check tire pressure. Do not make a visual judgement of outdoor temperatures, as tire pressures vary with when determining proper inflation.
Page 302: Radial Ply Tires
300 STARTING AND OPERATING Tire Pressures for High Speed Operation Radial Ply Tires The manufacturer advocates driving at safe speeds WARNING! within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle...
Page 303: Tire Spinning
STARTING AND OPERATING 301 vehicle only. Since this tire has limited tread life, the Do not install more than one compact spare tire/wheel original tire should be repaired (or replaced) and rein- on the vehicle at any given time. stalled at the first opportunity. CAUTION! WARNING! Because of the reduced ground clearance, do not take...
Page 304: Tread Wear Indicators
302 STARTING AND OPERATING WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) for more than 30 seconds continu- ously when you are stuck, and do not let anyone near a spinning wheel, no matter what the speed.
Page 305: Life Of Tire
STARTING AND OPERATING 303 Many states have laws requiring tire replacement at this Keep dismounted tires in a cool, dry place with as little point. exposure to light as possible. Protect tires from contact with oil, grease, and gasoline. Life Of Tire The service life of a tire is dependent upon varying Replacement Tires factors including, but not limited to:...
Page 306: Tire Chains
304 STARTING AND OPERATING WARNING! WARNING! (Continued) • Failure to equip your vehicle with tires having • Do not use a tire, wheel size or rating other than adequate speed capability can result in sudden tire that specified for your vehicle. Some combinations failure and loss of vehicle control.
Page 307 STARTING AND OPERATING 305 The 245/45 R20 size tires do not provide adequate CAUTION! (Continued) clearance for tire chains. • Do not exceed 30 mph (48 km/h). NOTE: Do not use tire chains on a compact spare tire. • Drive cautiously and avoid severe turns and large bumps, especially with a loaded vehicle.
Page 308: Snow Tires
306 STARTING AND OPERATING pavement. Observe the tire chain manufacturer’s instruc- Snow tires generally have lower speed ratings than what tions on method of installation, operating speed, and was originally equipped with your vehicle and should conditions for usage. not be operated at sustained speeds over 75 mph (120 km/h).
Page 309: Tire Pressure Monitor System (Tpms)
STARTING AND OPERATING 307 TIRE PRESSURE MONITOR SYSTEM (TPMS) The Tire Pressure Monitor System (TPMS) will warn the driver of a low tire pressure based on the vehicle recom- mended cold placard pressure. The tire pressure will vary with temperature by about 1 psi (6.9 kPa) for every 12°F (6.5°C).
Page 310 308 STARTING AND OPERATING The TPMS will warn the driver of a low tire pressure if For example, your vehicle may have a recommended the tire pressure falls below the low-pressure warning cold (parked for more than three hours) placard pressure limit for any reason, including low temperature effects of 30 psi (207 kPa).
Page 311 STARTING AND OPERATING 309 NOTE: CAUTION! • The TPMS is not intended to replace normal tire care • The TPMS has been optimized for the original and maintenance or to provide warning of a tire failure or condition. equipment tires and wheels. TPMS pressures and warning have been established for the tire size •...
Page 312: Base System
310 STARTING AND OPERATING • Seasonal temperature changes will affect tire pressure, Tire Pressure Monitoring Low Pressure Warnings and the TPMS will monitor the actual tire pressure in The TPM Telltale Light will illuminate in the the tire. instrument cluster and a chime will sound when tire pressure is low in one or more of the four Base System active road tires.
Page 313 STARTING AND OPERATING 311 off when the fault condition no longer exists. A system 2. If you install the compact spare tire in place of a road fault can occur due to any of the following: tire that has a pressure below the low-pressure warning limit, upon the next ignition key cycle, a chime will 1.
Page 314: Premium System - If Equipped
312 STARTING AND OPERATING • Various TPMS messages, which display in the Elec- Premium System — If Equipped The Tire Pressure Monitor System (TPMS) uses wireless tronic Vehicle Information Center (EVIC), and technology with wheel rim mounted electronic sensors to •...
Page 315 STARTING AND OPERATING 313 turn off. The vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information. Check TPMS Warning If a system fault is detected, the TPM Telltale Light will flash on and off for 75 seconds and then remain on solid.
Page 316 314 STARTING AND OPERATING 1. Signal interference due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPM sensors. 2. Installing aftermarket window tinting that contains materials that may block radio wave signals. 3. Accumulation of snow or ice around the wheels or wheel housings.
Page 317: General Information
STARTING AND OPERATING 315 limit, upon the next ignition key cycle, the TPM Telltale TPM Telltale Light will turn OFF and the graphic in the Light will remain ON and a chime will sound. In EVIC will display a new pressure value instead of dashes addition, the graphic in the EVIC will still display a (- -), as long as no tire pressure is below the low-pressure flashing pressure value.
Page 318: Fuel Requirements
316 STARTING AND OPERATING required. Poor quality gasoline can cause problems such United States ..... KR5S120123 as hard starting, stalling, and hesitations. If you experi- Canada .
Page 319: Reformulated Gasoline
STARTING AND OPERATING 317 Reformulated Gasoline CAUTION! Many areas of the country require the use of cleaner burning gasoline referred to as “reformulated gasoline.” DO NOT use gasolines containing Methanol or E85 Reformulated gasolines contain oxygenates and are spe- Ethanol. Use of these blends may result in starting cifically blended to reduce vehicle emissions and im- and driveability problems and may damage critical prove air quality.
Page 320: Mmt In Gasoline
318 STARTING AND OPERATING • operate in a lean mode MMT In Gasoline MMT is a manganese-containing metallic additive that is • OBD II “Malfunction Indicator Light” on blended into some gasoline to increase octane. Gasoline • poor engine performance blended with MMT provides no performance advantage beyond gasoline of the same octane number without •...
Page 321: Materials Added To Fuel
STARTING AND OPERATING 319 • An out-of-tune engine or certain fuel or ignition mal- Materials Added to Fuel All gasoline sold in the United States is required to functions can cause the catalytic converter to overheat. contain effective detergent additives. Use of additional If you notice a pungent burning odor or some light detergents or other additives is not needed under normal smoke, your engine may be out of tune or malfunc-...
Page 322: Carbon Monoxide Warnings
320 STARTING AND OPERATING • Guard against carbon monoxide with proper mainte- Carbon Monoxide Warnings nance. Have the exhaust system inspected every time WARNING! the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side Carbon monoxide (CO) in exhaust gases is deadly.
Page 323 STARTING AND OPERATING 321 Fuel Filler Cap Fuel Filler Cap (If Equipped) NOTE: When removing the fuel filler cap, lay the cap tether in the hook, located on the fuel filler door.
Page 324 322 STARTING AND OPERATING CAUTION! WARNING! (Continued) • Never add fuel to the vehicle when the engine is • Damage to the fuel system or emissions control running. system could result from using an improper fuel • A fire may result if gasoline is pumped into a tank filler tube cap (gas cap).
Page 325: Loose Fuel Filler Cap Message
STARTING AND OPERATING 323 Loose Fuel Filler Cap Message Do not exceed the specified Gross Vehicle Weight Rating If the vehicle diagnostic system determines that the fuel (GVWR) or the Gross Axle Weight Rating (GAWR). filler cap is loose, improperly installed, or damaged, a Vehicle Certification Label “Check Gascap”...
Page 326: Gross Vehicle Weight Rating (Gvwr)
324 STARTING AND OPERATING The bar code allows a computer scanner to read the VIN. WARNING! Gross Vehicle Weight Rating (GVWR) Because the front wheels steer the vehicle, it is The GVWR is the total allowable weight of your vehicle. important that you do not exceed the maximum front This includes driver, passengers, and cargo.
Page 327: Loading
STARTING AND OPERATING 325 Figure out the weight on the front and rear of the vehicle NOTE: Refer to the “Vehicle Certification Label” affixed separately. It is important that you distribute the load to the rear of the driver’s door for your vehicle’s GVWR evenly over the front and rear axles.
Page 328 326 STARTING AND OPERATING Gross Vehicle Weight Rating (GVWR) Gross Axle Weight Rating (GAWR) The GVWR is the total allowable weight of your vehicle. The GAWR is the maximum capacity of the front and rear This includes driver, passengers, cargo, and tongue axles.
Page 329 STARTING AND OPERATING 327 Frontal Area Weight-Distributing Hitch The frontal area is the maximum height and maximum A weight-distributing system works by applying lever- width of the front of a trailer. age through spring (load) bars. They are typically used for heavier loads to distribute trailer tongue weight to the Trailer Sway Control tow vehicle’s front axle and the trailer axle(s).
Page 330: Trailer Hitch Classification
328 STARTING AND OPERATING Trailer Hitch Classification Definitions WARNING! Class Max. Trailer Hitch Industry • An improperly adjusted weight distributing hitch Standards system may reduce handling, stability, braking Class I - Light Duty 2,000 lbs (907 kg) performance, and could result in an accident. Refer to the “Trailer Towing Weights (Maximum •...
Page 331: Trailer And Tongue Weight
STARTING AND OPERATING 329 Engine/Transmission Frontal Area Max. GTW (Gross Trailer Max. Tongue Wt. Wt.) 3.5L Automatic 12 sq ft (1.11 sq m) 1,000 lbs (454 kg) 100 lbs (45 kg) 5.7L Automatic 12 sq ft (1.11 sq m) 1,000 lbs (454 kg) 100 lbs (45 kg) Refer to local laws for maximum trailer towing speeds Trailer and Tongue Weight...
Page 332: Towing Requirements
330 STARTING AND OPERATING Consider the following items when computing the CAUTION! weight on the rear axle of the vehicle: • Avoid towing a trailer for the first 500 miles • The tongue weight of the trailer. (805 km) of vehicle operation. Doing so may dam- •...
Page 333 STARTING AND OPERATING 331 • Vehicles with trailers should not be parked on a grade. WARNING! (Continued) When parking, apply the parking brake on the tow Make certain that the load is secured in the trailer vehicle. Put the tow vehicle automatic transmission in and it will not shift during travel.
Page 334 332 STARTING AND OPERATING Towing Requirements — Tires Towing Requirements — Trailer Brakes − Do not attempt to tow a trailer while using a compact − Do not interconnect the hydraulic brake system or spare tire. vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible −...
Page 335 STARTING AND OPERATING 333 Towing Requirements — Trailer Lights and Wiring CAUTION! Whenever you pull a trailer, regardless of the trailer size, stoplights and turn signals on the trailer are required for If the trailer weighs more than 1,000 lbs (454 kg) motoring safety.
Page 336 334 STARTING AND OPERATING 4-Pin Connector 7-Pin Connector 1 — Female Pins 4 — Park 1 — Battery 5 — Ground 2 — Male Pin 5 — Left Stop/Turn 2 — Backup Lamps 6 — Left Stop/Turn 3 — Ground 6 —...
Page 337: Towing Tips
STARTING AND OPERATING 335 Towing Tips Towing Tips — Electronic Speed Control (If Before setting out on a trip, practice turning, stopping, Equipped) and backing up the trailer in an area located away from − Do not use in hilly terrain or with heavy loads. heavy traffic.
Page 338: Recreational Towing (Behind Motorhome, Etc.)
336 STARTING AND OPERATING − Extended driving at high RPM should be avoided to − Highway Driving prevent excess heat generation. A reduction in vehicle Reduce speed. speed may be required to avoid extended driving at − Air Conditioning high RPM. Return to a higher gear range or vehicle Turn off temporarily.
Page 339 WHAT TO DO IN EMERGENCIES CONTENTS Jump-Starting ..... . . 355 Hazard Warning Flasher ....338 Freeing A Stuck Vehicle .
Page 340: Hazard Warning Flasher
338 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER NOTE: With extended use, the Hazard Warning flasher The Hazard Warning flasher switch is located in the may wear down your battery. switch bank near the bottom center of the instrument IF YOUR ENGINE OVERHEATS panel.
Page 341: Tirefit Tire Repair - If Equipped
WHAT TO DO IN EMERGENCIES 339 the fan control to high. This allows the heater core to act WARNING! as a supplement to the radiator and aids in removing heat from the engine cooling system. A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling CAUTION! coolant.
Page 342 340 WHAT TO DO IN EMERGENCIES The TIREFIT system is located under an access panel in the trunk. TIREFIT Kit 1. Air pump hose TIREFIT Location 2. Power plug and cable 3. AIR PUMP switch 4. Pressure gauge...
Page 343 WHAT TO DO IN EMERGENCIES 341 5. TIREFIT sealant bottle WARNING! (Continued) 6. TIREFIT sealant hose • Take care not to allow the contents of TIREFIT to come in contact with hair, eyes or clothing. TIRE- WARNING! FIT is harmful if inhaled, swallowed, or absorbed through the skin: It causes skin, eye, and respira- •...
Page 344 342 WHAT TO DO IN EMERGENCIES Sealing Tire with TIREFIT 8. Leave the parking brake set and the shift lever in PARK (automatic transmission) or gear (manual trans- 1. Turn on the Hazard Warning Flashers. mission) and start the engine. 2.
Page 345 WHAT TO DO IN EMERGENCIES 343 13. Turn on the Hazard Warning Flashers. 26 psi (1.8 bar) is not obtained within five minutes, the tire is too badly damaged. Do not attempt to drive the 14. Move the shift lever into PARK (automatic transmis- vehicle further.
Page 346 344 WHAT TO DO IN EMERGENCIES 24. Connect the air pump hose valve to the tire valve and 28. Disconnect the TIREFIT system from the tire and flip the hose valve closed. reinstall the valve cap. 25. Check the pressure in the tire by reading the pressure 29.
Page 347: Jacking And Tire Changing
WHAT TO DO IN EMERGENCIES 345 • If TIREFIT is liquid, clean water and a damp cloth will WARNING! (Continued) remove the material from the vehicle or tire and wheel • Getting under a jacked-up vehicle is dangerous. components. Once TIREFIT sealing material has dried, The vehicle could slip off the jack and fall on you.
Page 348 346 WHAT TO DO IN EMERGENCIES NOTE: The spare tire must be removed in order to access the jack. 1. Open the trunk. 2. Lift the access cover using the pull strap. Spare Tire Fastener 4. Remove the spare tire. 5.
Page 349: Preparations For Jacking
WHAT TO DO IN EMERGENCIES 347 Preparations For Jacking 1. Park the vehicle on a firm level surface as far from the edge of the roadway as possible. Avoid icy or slippery areas. 2. Set the parking brake and place the shift lever into PARK (automatic transmission) or REVERSE (manual transmission).
Page 350: Jacking And Changing A Tire
348 WHAT TO DO IN EMERGENCIES NOTE: Passengers should not remain in the vehicle WARNING! (Continued) when the vehicle is being jacked. • Never start or run the engine with the vehicle on a Jacking and Changing a Tire jack. •...
Page 351 WHAT TO DO IN EMERGENCIES 349 Jack Warning Label 1. Remove the spare tire, jack, and lug wrench. 2. If equipped with steel wheels, do not remove the wheel cover at this time. If equipped with aluminum wheels where the center cap covers the lug nuts, use the lug wrench to pry the center cap off carefully before Center Cap Removal raising the vehicle.
Page 352 350 WHAT TO DO IN EMERGENCIES 3. Before raising the vehicle, use the lug wrench to 4. Place the jack underneath the lift area that is closest to loosen, but not remove, the lug nuts on the wheel with the flat tire. Turn the jack screw clockwise to firmly the flat tire.
Page 353 WHAT TO DO IN EMERGENCIES 351 avoid the risk of forcing the vehicle off the jack, do not WARNING! tighten the lug nuts fully until the vehicle is lowered to the ground. Raising the vehicle higher than necessary can make the vehicle less stable.
Page 354: Compact Spare Tire
352 WHAT TO DO IN EMERGENCIES WARNING! WARNING! A loose tire or jack thrown forward in a collision or The limited-use spare tires are for emergency use hard stop could endanger the occupants of the ve- only. Installation of this limited-use spare tire affects hicle.
Page 355 WHAT TO DO IN EMERGENCIES 353 1. Mount the road tire on the axle. For vehicles equipped with wheel covers, perform Steps 2 and 3. For vehicles equipped with center caps, proceed to Step 4. 2. Install two lug nuts on the mounting studs, which are on each side of the stud that is in alignment with the valve stem.
Page 356 354 WHAT TO DO IN EMERGENCIES snapping the cover over the two lug nuts. Do not use a 7. For vehicles equipped with center caps, install the hammer or excessive force to install the cover. center cap by hand. Do not use a hammer or excessive force to install the center cap.
Page 357: Jump-Starting
WHAT TO DO IN EMERGENCIES 355 JUMP-STARTING WARNING! (Continued) • Battery fluid is a corrosive acid solution; do not WARNING! allow battery fluid to contact eyes, skin, or cloth- • Take care to avoid the radiator cooling fan when- ing. Don’t lean over battery when attaching ever the hood is raised.
Page 358 356 WHAT TO DO IN EMERGENCIES NOTE: The battery is stored under an access cover in 3. Set the parking brake, place the automatic transmis- the trunk. Remote battery terminals are located in the sion in PARK (manual transmission in NEUTRAL), and engine compartment for jump-starting.
Page 359 WHAT TO DO IN EMERGENCIES 357 NOTE: Refer to Synchronizing ESP under Electronic Stability Program in Section 5 if the ESP/BAS light (in the instrument cluster) remains on continuously after starting the engine of the vehicle with the discharged battery. 8.
Page 360: Freeing A Stuck Vehicle
358 WHAT TO DO IN EMERGENCIES NOTE: Turn off the Electronic Stability Program (ESP) WARNING! (Continued) before rocking the vehicle. Refer to “Electronic Stability • During cold weather when temperatures are be- Program,” or “Traction Control” in Section 5. low the freezing point, electrolyte in a discharged battery may freeze.
Page 361: Towing A Disabled Vehicle
WHAT TO DO IN EMERGENCIES 359 Towing This Vehicle Behind Another Vehicle (Flat WARNING! Towing With All Four Wheels On The Ground) Flat towing of vehicles is permitted within the following Fast spinning tires can be dangerous. Forces gener- limitations: ated by excessive wheel speeds may cause tire dam- age or failure.
Page 362: Towing This Vehicle Behind Another Vehicle With A Tow Dolly
360 WHAT TO DO IN EMERGENCIES If the transmission is not operative or if the vehicle is to If you must use the accessories (wipers, defrosters, etc.) be towed more than 30 miles (48 km), the vehicle must be while being towed, the key must be in the ON position, transported using a flatbed truck.
Page 363 MAINTAINING YOUR VEHICLE CONTENTS Engine Oil ......368 Engine Compartment — 3.5L ... . 363 Engine Oil Filter .
Page 364 362 MAINTAINING YOUR VEHICLE Brake System ..... . 385 Low Beam Headlight, High Beam Headlight, Park/Turn Light — Models With Halogen Clutch Hydraulic System —...
Page 365: Engine Compartment - 3.5L
MAINTAINING YOUR VEHICLE 363 ENGINE COMPARTMENT — 3.5L 1 — Integrated Power Module 6 — Engine Coolant Reservoir 2 — Air Cleaner Filter 7 — Engine Oil Fill 3 — Brake Fluid Reservoir Access Cover 8 — Engine Oil Dipstick 4 —...
Page 366: Engine Compartment - 5.7L
364 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 5.7L 1 — Integrated Power Module 6 — Air Cleaner Filter 2 — Coolant Pressure Cap 7 — Engine Oil Fill 3 — Brake Fluid Reservoir Access Cover 8 — Engine Oil Dipstick 4 —...
Page 367: Onboard Diagnostic System - Obd Ii
MAINTAINING YOUR VEHICLE 365 ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors Prolonged driving with the MIL on could cause the performance of the emissions, engine, and automatic further damage to the emissions control system.
Page 368: Emissions Inspection And Maintenance Programs
366 MAINTAINING YOUR VEHICLE Trip Odometer button to turn off the message. If the serviced, recently had a dead battery, or a battery replace- problem continues, the message will appear the next time ment. If the OBD II system should be determined not the vehicle is started.
Page 369: Replacement Parts
MAINTAINING YOUR VEHICLE 367 5. Approximately 15 seconds later, one of two things will as you normally would in order for the OBD II system to happen: update. A recheck with the above test routine may then indicate that the system is now ready. a.
Page 370: Dealer Service
368 MAINTAINING YOUR VEHICLE DEALER SERVICE MAINTENANCE PROCEDURES Your authorized dealer has the qualified service person- The pages that follow contain the required maintenance nel, special tools, and equipment to perform all service services determined by the engineers who designed your operations in an expert manner.
Page 371 MAINTAINING YOUR VEHICLE 369 The best time to check the engine oil level is about five The best time to check the engine oil level is about five minutes after a fully warmed engine is shut off. minutes after a fully warmed engine is shut off. Checking the oil while the vehicle is on level ground will Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings.
Page 372 370 MAINTAINING YOUR VEHICLE NOTE: Under no circumstances should oil change Engine Oil Viscosity (SAE Grade) — 3.5L Engine intervals exceed 6,000 miles (10 000 km) or six months, SAE 10W-30 engine oil is preferred for for all operating whichever occurs first. temperatures.
Page 373: Engine Oil Filter
MAINTAINING YOUR VEHICLE 371 The engine oil filler cap also shows the recommended Disposing of Used Engine Oil and Oil Filters engine oil viscosity for your engine. For information on Care should be taken in disposing of used engine oil and engine oil filler cap location, refer to “Engine Compart- oil filters from your vehicle.
Page 374: Engine Air Cleaner Filter
372 MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter Engine Air Cleaner Filter Selection Refer to the “Maintenance Schedule” in Section 8 for The quality of replacement engine air cleaner filters proper maintenance intervals. varies considerably. Only high quality filters should be used to assure most efficient service.
Page 375 MAINTAINING YOUR VEHICLE 373 WARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water.
Page 376: Air Conditioner Maintenance
374 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance WARNING! (Continued) For best possible performance, your air conditioner • The battery in this vehicle has a vent hose that should be checked and serviced by an authorized dealer should not be disconnected and should only be at the start of each warm season.
Page 377: Body Lubrication
MAINTAINING YOUR VEHICLE 375 Body Lubrication WARNING! (Continued) Locks and all body pivot points, including such items as • The air conditioning system contains refrigerant seat tracks, door hinge pivot points and rollers, liftgate, under high pressure. To avoid risk of personal tailgate, sliding doors and hood hinges, should be lubri- injury or damage to the system, adding refrigerant cated periodically with a lithium based grease such as...
Page 378: Windshield Wiper Blades
376 MAINTAINING YOUR VEHICLE Windshield Wiper Blades windshield washer solvent (not radiator antifreeze) and Clean the rubber edges of the wiper blades and the operate the system for a few seconds to flush out the windshield periodically with a sponge or soft cloth and a residual water.
Page 379: Exhaust System
MAINTAINING YOUR VEHICLE 377 inspect the exhaust system each time the vehicle is raised WARNING! for lubrication or oil change. Replace as required. Commercially available windshield washer solvents WARNING! are flammable. They could ignite and burn you. Care must be exercised when filling or working around Exhaust gases can injure or kill.
Page 380 378 MAINTAINING YOUR VEHICLE CAUTION! WARNING! Damage to the catalytic converter can result if your A hot exhaust system can start a fire if you park over vehicle is not kept in proper operating condition. In materials that can burn. Such materials might be the event of engine malfunction, particularly involv- grass or leaves coming into contact with your exhaust ing engine misfire or other apparent loss of perfor-...
Page 381: Cooling System
MAINTAINING YOUR VEHICLE 379 To minimize the possibility of catalyst damage: Cooling System • Do not shut off the engine or interrupt the ignition WARNING! when the transmission is in gear and the vehicle is in • When working near the radiator cooling fan, dis- motion.
Page 382 380 MAINTAINING YOUR VEHICLE system should be drained, flushed, and refilled with Cooling System — Drain, Flush, and Refill fresh coolant. Check the front of the radiator for any If the engine coolant (antifreeze) is dirty or contains a accumulation of bugs, leaves, etc. If dirty, clean by gently considerable amount of sediment, clean and flush with a spraying water from a garden hose vertically down the reliable cooling system cleaner.
Page 383 MAINTAINING YOUR VEHICLE 381 CAUTION! CAUTION! (Continued) • This vehicle has not been designed for use with • Mixing of engine coolant (antifreeze) other than propylene glycol-based engine coolant (anti- specified HOAT engine coolant (antifreeze), may freeze). Use of propylene glycol-based engine result in engine damage and may decrease corro- coolant (antifreeze) is not recommended.
Page 384 382 MAINTAINING YOUR VEHICLE When adding engine coolant (antifreeze): NOTE: Mixing engine coolant (antifreeze) types will decrease the life of the engine coolant (antifreeze) and • The manufacturer recommends using MOPAR will require more frequent engine coolant (antifreeze) Antifreeze/Coolant 5 Year/100,000 Mile Formula changes.
Page 385 MAINTAINING YOUR VEHICLE 383 rules for your community. To prevent ingestion by ani- WARNING! mals or children, do not store ethylene glycol-based • The warning words “DO NOT OPEN HOT” on engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground.
Page 386 384 MAINTAINING YOUR VEHICLE • Do not overfill the coolant recovery bottle. of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once • Check engine coolant (antifreeze) freeze point in the a month.
Page 387: Brake System
MAINTAINING YOUR VEHICLE 385 • Keep the front of the radiator clean. If your vehicle is WARNING! equipped with air conditioning, keep the front of the condenser clean. Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting •...
Page 388 386 MAINTAINING YOUR VEHICLE Overfilling of fluid is not recommended because it may WARNING! (Continued) cause leaking in the system. • Use of a brake fluid that may have a lower initial Add enough fluid to bring the level up to the require- boiling point, or is unidentified as to specification, ments described on the brake fluid reservoir.
Page 389: Clutch Hydraulic System - Manual Transmission (If Equipped)
MAINTAINING YOUR VEHICLE 387 Clutch Hydraulic System — Manual Transmission CAUTION! (If Equipped) The clutch hydraulic system is fed by a segregated Using a transmission fluid other than the manufac- volume of fluid within the brake system master cylinder turer’s recommended fluid may cause deterioration reservoir.
Page 390 388 MAINTAINING YOUR VEHICLE If you notice fluid loss or gear shift malfunction, have CAUTION! (Continued) your authorized dealer check the transmission fluid level. • The fluid level is preset at the factory and it does not require adjustment under normal operating CAUTION! conditions.
Page 391: Rear Axle
MAINTAINING YOUR VEHICLE 389 Selection of Lubricant Rear Axle It is important that the proper lubricant is used in the Fluid Level Check transmission to assure optimum transmission perfor- Check the fluid level by removing the fill plug on the mance.
Page 392 390 MAINTAINING YOUR VEHICLE • Atmospheric fallout/industrial pollutants. parking, which exposes your vehicle to airborne contami- nants, road surfaces on which the vehicle is operated, Washing extreme hot or cold weather and other extreme condi- • Wash your vehicle regularly. Always wash your ve- tions will have an adverse effect on paint, metal trim, and underbody protection.
Page 393 MAINTAINING YOUR VEHICLE 391 • If your vehicle is damaged due to an accident or CAUTION! similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as pos- Do not use abrasive or strong cleaning materials such sible.
Page 394 392 MAINTAINING YOUR VEHICLE heavy soil and/or excessive brake dust, use MOPAR Your leather upholstery can be best preserved by regular Wheel Cleaner (05066247AB) or equivalent or select a cleaning with a damp soft cloth. Small particles of dirt nonabrasive, non-acidic cleaner. Do not use scouring can act as an abrasive and damage the leather upholstery pads, steel wool, a bristle brush, or metal polishes.
Page 395 MAINTAINING YOUR VEHICLE 393 Cleaning Headlights quarter window equipped with the radio antenna. Do Your vehicle has plastic headlights that are lighter and not use scrapers or other sharp instrument that may less susceptible to stone breakage than glass headlights. scratch the elements.
Page 396: Fuses
394 MAINTAINING YOUR VEHICLE Seat Belt Maintenance FUSES Do not bleach, dye, or clean the belts with chemical Integrated Power Module (IPM) solvents or abrasive cleaners. This will weaken the fabric. The Integrated Power Module (IPM) is located in the Sun damage can also weaken the fabric.
Page 397 MAINTAINING YOUR VEHICLE 395 Cavity Car- Mini- Description CAUTION! tridge Fuse • When installing the integrated power module Fuse cover, it is important to ensure the cover is prop- — 15 Amp Washer Motor erly positioned and fully latched. Failure to do so Blue may allow water to get into the integrated power —...
Page 398 396 MAINTAINING YOUR VEHICLE Cavity Car- Mini- Description Cavity Car- Mini- Description tridge Fuse tridge Fuse Fuse Fuse — 25 Amp Starter 50 Amp — Radiator Fan Neutral — — — — — — 30 Amp — Windshield Wiper — —...
Page 399: Rear Power Distribution Center
MAINTAINING YOUR VEHICLE 397 Rear Power Distribution Center There is also a power distribution center located in the trunk under the spare tire access panel. This center contains fuses and relays. Rear Power Distribution Center Access Panel...
Page 400 398 MAINTAINING YOUR VEHICLE Cavity Car- Mini- Description CAUTION! tridge Fuse • When installing the power distribution center Fuse cover, it is important to ensure the cover is prop- 60 Amp — Ignition Off Draw (IOD) erly positioned and fully latched. Failure to do so Yellow may allow water to get into the power distribution 40 Amp...
Page 401 MAINTAINING YOUR VEHICLE 399 Cavity Car- Mini- Description Cavity Car- Mini- Description tridge Fuse tridge Fuse Fuse Fuse — 15 Amp Diagnostic Link Connec- — 20 Amp Cluster Blue tor (DLC)/Wireless Con- Yellow trol Module (WCM)/ — 20 Amp Selectable Power Outlet Wireless Ignition Node Yellow (WIN)
Page 402 400 MAINTAINING YOUR VEHICLE Cavity Car- Mini- Description Cavity Car- Mini- Description tridge Fuse tridge Fuse Fuse Fuse — 10 Amp Ignition Run — 5 Amp Antenna Module - if Orange equipped/Power Mir- rors — 5 Amp Cluster/Electronic Sta- Orange bility Program (ESP)/ —...
Page 403: Vehicle Storage
MAINTAINING YOUR VEHICLE 401 window switch, and the passenger power window Cavity Car- Mini- Description switch are fused by the 25 Amp circuit breaker in cavity tridge Fuse 13. If you experience temporary or permanent loss of Fuse these systems, see your authorized dealer for service. —...
Page 404: Replacement Light Bulbs
402 MAINTAINING YOUR VEHICLE REPLACEMENT LIGHT BULBS LIGHT BULBS — Exterior Bulb Number Low Beam Headlight – High Intensity Discharge (HID) ......D1S LIGHT BULBS —...
Page 405: Bulb Replacement
MAINTAINING YOUR VEHICLE 403 BULB REPLACEMENT WARNING! Low Beam Headlight, High Beam Headlight, A transient high tension occurs at the bulb sockets of Park/Turn Light — Models with Halogen HID headlights when the HEADLIGHT switch is Headlights — If Equipped turned ON.
Page 406: Tail/Turn/Stop Light
404 MAINTAINING YOUR VEHICLE NOTE: Tail/Turn/Stop Light • If a screwdriver is used, make sure a soft material is 1. Open the trunk. placed between the vehicle body and tool so not to scratch the paint. 2. Using a screwdriver, remove the tail light retainer. 2.
Page 407 MAINTAINING YOUR VEHICLE 405 3. Remove the fasteners from the back of the tail light 5. Remove the remaining fasteners from the back of the assembly. tail light assembly. 6. Pull the tail light assembly clear from the vehicle to access the bulbs.
Page 408 406 MAINTAINING YOUR VEHICLE 7. Push the electrical connector locking tab to the side. 8. Disconnect the electrical connector. 9. Turn the appropriate bulb and socket assembly coun- terclockwise to remove it from the tail light assembly. 10. Disconnect the bulb from the socket assembly and install the replacement bulb.
Page 409: Center Tail/Backup Light
MAINTAINING YOUR VEHICLE 407 Center Tail/Backup Light See your authorized dealer for bulb replacement. Center High-Mounted Stop Light (CHMSL) The CHMSL uses LED lights that are not serviceable separately. The CHMSL must be replaced as an assembly, see your authorized dealer. License Light 1.
Page 410: Fluids And Capacities
408 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES U.S. Metric Fuel (Approximate) 3.5 Liter Engine 18 Gallons 68 Liters 5.7 Liter Engine 19 Gallons 72 Liters Engine Oil with Filter 3.5 Liter Engine (SAE 10W-30, API Certified) 6.0 Quarts 5.7 Liters 5.7 Liter Engine (SAE 5W-20, API Certified) 7.0 Quarts 6.6 Liters...
Page 411: Fluids, Lubricants, And Genuine Parts
MAINTAINING YOUR VEHICLE 409 FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant MOPAR Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) Engine Oil (3.5L Engine) Use API Certified SAE 10W-30 Engine Oil meeting the requirements of Chrysler Material Standard MS-6395.
Page 412: Chassis
410 MAINTAINING YOUR VEHICLE Chassis Component Fluid, Lubricant, or Genuine Part Manual Transmission MOPAR ATF+4 Automatic Transmission Fluid Automatic Transmission MOPAR ATF+4 Automatic Transmission Fluid Brake Master Cylinder MOPAR DOT 3, SAE J1703 or equivalent should be used. If DOT 3 brake fluid is not available, then DOT 4 is acceptable.
Page 413 MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..412 Required Maintenance Intervals ..414 Maintenance Schedule ....412...
Page 414 412 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE MAINTENANCE SCHEDULE The Scheduled Maintenance services listed in bold type, The oil change indicator system will remind you that it is must be done at the times or mileages specified to ensure time to take your vehicle in for scheduled maintenance. the continued proper functioning of the Emission Control On Electronic Vehicle Information Center (EVIC) System.
Page 415 MAINTENANCE SCHEDULES 413 NOTE: scheduled oil change is performed by someone other • The oil change indicator message will not monitor the than your authorized dealer, the message can be reset by time since the last oil change. Change your vehicle’s referring to the steps described under “Oil Change oil if it has been six months since your last oil change, Required”...
Page 416 414 MAINTENANCE SCHEDULES Once a Month CAUTION! • Check tire pressure and look for unusual wear or Failure to perform the required maintenance items damage. may result in damage to the vehicle. • Inspect the battery, and clean and tighten the terminals as required.
Page 417 MAINTENANCE SCHEDULES 415 6,000 Miles (10,000 km) or 12,000 Miles (20,000 km) or 12 Months Maintenance Service 6 Months Maintenance Service Schedule Schedule Change the engine oil and engine oil filter. Rotate tires. Change the engine oil and engine oil If using your vehicle for any of the following: Dusty or off-road conditions.
Page 418 416 MAINTENANCE SCHEDULES 18,000 Miles (30,000 km) or 24,000 Miles (40,000 km) or 24 Months Maintenance Service 18 Months Maintenance Schedule Service Schedule Change the engine oil and engine oil filter. Rotate tires. Change the engine oil and engine oil If using your vehicle for any of the following: Dusty or off-road conditions.
Page 419 MAINTENANCE SCHEDULES 417 30,000 Miles (50,000 km) or 36,000 Miles (60,000 km) or 36 Months Maintenance Service 30 Months Maintenance Schedule Service Schedule Change the engine oil and engine oil filter. Rotate tires. Change the engine oil and engine oil If using your vehicle for any of the following: Dusty or off-road conditions.
Page 420 418 MAINTENANCE SCHEDULES 42,000 Miles (70,000 km) or 48,000 Miles (80,000 km) or 48 Months Maintenance Service 42 Months Maintenance Schedule Service Schedule Change the engine oil and engine oil filter. Rotate tires. Change the engine oil and engine oil If using your vehicle for any of the following: Dusty or off-road conditions.
Page 421 MAINTENANCE SCHEDULES 419 54,000 Miles (90,000 km) or 60,000 Miles (100,000 km) or 60 Months Maintenance Service 54 Months Maintenance Schedule Service Schedule Change the engine oil and engine oil filter. Rotate tires. Change the engine oil and engine oil Replace the engine air cleaner filter.
Page 422 420 MAINTENANCE SCHEDULES 66,000 Miles (110,000 km) or 72,000 Miles (120,000 km) or 72 Months Maintenance Service 66 Months Maintenance Schedule Service Schedule Change the engine oil and engine oil filter. Rotate tires. Change the engine oil and engine oil Replace the air conditioning filter (if equipped) filter.
Page 423 MAINTENANCE SCHEDULES 421 78,000 Miles (130,000 km) or 84,000 Miles (140,000 km) or 90,000 Miles (150,000 km) or 78 Months Maintenance 84 Months Maintenance 90 Months Maintenance Service Schedule Service Schedule Service Schedule Change the engine oil and engine oil Change the engine oil and engine oil Change the engine oil and engine oil filter.
Page 424 422 MAINTENANCE SCHEDULES 96,000 Miles (160,000 km) or 102,000 Miles (170,000 km) or 108,000 Miles (180,000 km) or 96 Months Maintenance 102 Months Maintenance 108 Months Maintenance Service Schedule Service Schedule Service Schedule Change the engine oil and engine oil Change the engine oil and engine oil Change the engine oil and engine oil filter.
Page 425 MAINTENANCE SCHEDULES 423 114,000 Miles (190,000 km) or 120,000 Miles (200,000 km) or 120 Months Maintenance Service 114 Months Maintenance Schedule Service Schedule Change the engine oil and engine oil filter. Rotate tires. Change the engine oil and engine oil Replace the engine air cleaner filter.
Page 426 424 MAINTENANCE SCHEDULES 126,000 Miles (210,000 km) or 132,000 Miles (220,000 km) or 138,000 Miles (230,000 km) or 126 Months Maintenance 132 Months Maintenance 138 Months Maintenance Service Schedule Service Schedule Service Schedule Change the engine oil and engine oil Change the engine oil and engine oil Change the engine oil and engine oil filter.
Page 427 MAINTENANCE SCHEDULES 425 144,000 Miles (240,000 km) or 144 Months Maintenance Service 150,000 Miles (250,000 km) or Schedule 150 Months Maintenance Change the engine oil and engine oil filter. Service Schedule Rotate tires. Change the engine oil and engine oil Replace the air conditioning filter (if equipped) filter.
Page 428 426 MAINTENANCE SCHEDULES † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment.
Page 429: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Customer Assistance For The Hearing Or Vehicle......429 Speech Impaired (TDD/TTY) .
Page 430 428 IF YOU NEED CONSUMER ASSISTANCE Publication Order Forms ....433 Traction Grades ....435 Department Of Transportation Uniform Tire Temperature Grades .
Page 431: Suggestions For Obtaining Service For Your Vehicle
IF YOU NEED CONSUMER ASSISTANCE 429 SUGGESTIONS FOR OBTAINING SERVICE FOR the service advisor and list the items in order of priority. YOUR VEHICLE At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the...
Page 432: Chrysler Llc Customer Center
430 IF YOU NEED CONSUMER ASSISTANCE • Vehicle delivery date and mileage This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- Chrysler LLC Customer Center solved with this process. P.O. Box 21–8004 •...
Page 433: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
IF YOU NEED CONSUMER ASSISTANCE 431 Customer Assistance For The Hearing Or Speech date. If you have any questions about the service con- Impaired (TDD/TTY) tract, call the manufacturer’s Service Contract National To assist customers who have hearing difficulties, the Customer Hotline at 1-800-521-9922.
Page 434: Warranty Information (U.s. Vehicles Only)
432 IF YOU NEED CONSUMER ASSISTANCE MOPAR PARTS WARNING! MOPAR fluids, lubricants, parts, and accessories are available from an authorized dealer. They will help keep Engine exhaust, some of its constituents, and certain the vehicle operating at its best. vehicle components contain, or emit, chemicals known to the State of California to cause cancer and REPORTING SAFETY DEFECTS birth defects or other reproductive harm.
Page 435: In Canada
IF YOU NEED CONSUMER ASSISTANCE 433 To contact NHTSA, you may either call the Auto Safety PUBLICATION ORDER FORMS Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), To order the following manuals, you may use either the or go to http://www.safercar.gov; or write to: Administra- website or the phone numbers listed below.
Page 436: Quality Grades
434 IF YOU NEED CONSUMER ASSISTANCE • Diagnostic Procedure Manuals Call toll free at: • 1–800–890–4038 (U.S.) Diagnostic Procedure Manuals are filled with dia- grams, charts and detailed illustrations. These practi- • 1–800–387–1143 (Canada) cal manuals make it easy for students and technicians to find and fix problems on computer-controlled ve- hicle systems and features.
Page 437: Traction Grades
IF YOU NEED CONSUMER ASSISTANCE 435 Treadwear WARNING! The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled The traction grade assigned to this tire is based on conditions on a specified government test course. For straight-ahead braking traction tests, and does not example, a tire graded 150 would wear one and one-half include acceleration, cornering, hydroplaning, or...
Page 438 436 IF YOU NEED CONSUMER ASSISTANCE WARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive load- ing, either separately or in combination, can cause heat buildup and possible tire failure.
Page 439 INDEX...
Page 440 438 INDEX About Your Brakes ....276,278 Airbag, Side ......47,52 ABS (Anti-Lock Brake System) .
Page 441 INDEX 439 Automatic Door Locks ....30,31 Axle Fluid ......410 Automatic Headlights .
Page 442 440 INDEX Parking ......276 Cellular Phone ......79 Warning Light .
Page 443 INDEX 441 Compact Spare Tire ..... . 300 Inspection ......383 Compass .
Page 444 442 INDEX Delay (Intermittent) Wipers ....127 Electrical Power Outlets ....143 Diagnostic System, Onboard .
Page 445 INDEX 443 Block Heater ......251 Starting ......243 Break-In Recommendations .
Page 446 444 INDEX Flashers Freeing A Stuck Vehicle ....358 Hazard Warning ..... . . 338 Fuel .
Page 447 INDEX 445 Garage Door Opener (HomeLink ) ... 134 Hands-Free Phone (uconnect) ....79 Gas Cap (Fuel Filler Cap) ....320,365 Hazard Gasoline, Clean Air .
Page 448 446 INDEX Heater ....... 230 Instrument Panel Lens Cleaning ... . . 393 Heater, Engine Block .
Page 449 INDEX 447 Kicker Sound System ..... 227 Brake Warning ..... 164,278 Knee Bolster .
Page 450 448 INDEX High Beam/Low Beam Select ... . . 124 Tire Pressure Monitoring (TPMS) ..166,307 Illuminated Entry ..... . . 19 Traction Control .
Page 451 INDEX 449 Maintenance Free Battery ....372 Outside ......76 Maintenance, General .
Page 452 450 INDEX Checking ......368,369 Owner’s Manual (Operator Manual) ..433 Dipstick .
Page 453 INDEX 451 Seats ....... 113 Rear Seat, Folding ..... . . 117 Steering .
Page 454 452 INDEX Replacement Tires ..... . . 303 Seat Belt Reminder ..... . . 43 Reporting Safety Defects .
Page 455 INDEX 453 Rear Folding ......117 Shoulder Belts ......37 Seatback Release .
Page 456 454 INDEX Cold Weather ......249 Sunglasses Storage ..... . . 134 Emergency (Jump Starting) .
Page 457 INDEX 455 TIREFIT ......339 Rotation ......306 Tires .
Page 458 456 INDEX Towing Vehicle Behind a Motor Home ..336 Transmitter Battery Service Traction Control ......282 (Remote Keyless Entry) .
Page 459 INDEX 457 Unleaded Gasoline ..... . . 316 Washers, Windshield ....126,127,376 Untwisting Procedure, Seat Belt .
Page 460 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use frequency signals. Mobile two-way radios and telephone only fully shielded coaxial cable.
Page 461 Chrysler LLC 81-226-0916 Second Edition Printed in U.S.A.
Page 462 SRT8 includes 2010...
Page 463 IMPORTANT: This User Guide is intended to familiarize you with the important features of your vehicle. The DVD enclosed contains your Owner’s Manual, Navigation/Media Center Manuals, Warranty Booklets, Tire Warranty and 24-Hour Towing Assistance (new vehicles purchased in the U.S.) or Roadside Assistance (new vehicles purchased in Canada) in electronic format.
Page 464 TABLE OF CONTENTS INTRODUCTION/WELCOME RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) ... 38 WELCOME FROM CHRYSLER BRAKE/TRANSMISSION INTERLOCK GROUP LLC ....2 MANUAL OVERRIDE .
Page 465: Introduction/Welcome
INTRODUCTION/WELCOME WELCOME FROM CHRYSLER GROUP LLC Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This guide illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle.
Page 466 Never park your vehicle over dry grass or other combustible materials. The heat from your vehicle exhaust system could cause a fire. CHRYSLER, DODGE, JEEP, ATF+4, MOPAR and Uconnect are registered trademarks of Chrysler Group LLC. COPYRIGHT ©2010 CHRYSLER GROUP LLC...
Page 467: Controls At A Glance
CONTROLS AT A GLANCE DRIVER COCKPIT...
Page 468 CONTROLS AT A GLANCE...
Page 469: Instrument Cluster
CONTROLS AT A GLANCE INSTRUMENT CLUSTER Warning Lights - Low Fuel Warning Light - Charging System Light** - Oil Pressure Warning Light** - Anti-Lock Brake (ABS) Light** - Airbag Warning Light** - Electronic Throttle Control (ETC) Light - Tire Pressure Monitoring System (TPMS) Light - Engine Temperature Warning Light - Seat Belt Reminder Light BRAKE...
Page 470 CONTROLS AT A GLANCE Indicators - Turn Signal Indicators - Electronic Stability Program (ESP) Indicator - High Beam Indicator - Windshield Washer Fluid Low - Front Fog Light Indicator Indicator*** - Vehicle Security Indicator* - Door Ajar Indicator*** - Electronic Speed Control / - Decklid Ajar Indicator*** Adaptive Cruise Control (ACC) Indicator...
Page 471: Getting Started
GETTING STARTED KEY FOB Locking And Unlocking The Doors • Press the LOCK button once to lock all the doors. Press the UNLOCK button once to unlock the driver’s door only and twice within five seconds to unlock all the doors. •...
Page 472: Keyless Go
GETTING STARTED Express Window Feature • To remotely lower both front door windows at the same time, press and release the UNLOCK button and then immediately press and hold the UNLOCK button until the windows lower to the level desired or until they lower completely. Emergency Key •...
Page 473: Theft Alarm
GETTING STARTED Stopping • With the vehicle stopped, place the shift lever in NEUTRAL. • Press the ENGINE START/STOP button once. The ignition switch will return to the OFF position. • If the vehicle speed is above 5 mph (8 km/h), the ENGINE START/STOP button must be held for two seconds before the engine will shut off.
Page 474: Seat Belt
GETTING STARTED SEAT BELT • Be sure everyone in your vehicle is in a seat and using a seat belt properly. WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle.
Page 475 GETTING STARTED • The rear seat lower anchorages are round bars, located at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the intersection of the seatback and seat cushion surfaces.
Page 476: Front Seats
GETTING STARTED • Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. • Attach the tether strap hook of the child restraint to the anchor and remove slack in the tether strap according to the child restraint manufacturer’s instructions.
Page 477 GETTING STARTED Passenger Forward/Rearward • Lift up on the adjusting bar located at the front of the seat near the floor and release at the desired position. Passenger Easy Entry Seats • For easy access to the rear seat, pull upward on the easy entry lever, located on the passenger seatback;...
Page 478: Rear Seat
GETTING STARTED REAR SEAT Folding Rear Seatback • Pull on the loops, located near the outer top of the seatbacks, to fold down either or both seatbacks. These loops can be tucked away when not in use. • When the seatback is raised to the upright position, make sure it is latched by strongly pulling on the top of the seatback above the seat loop.
Page 479: Tilt / Telescoping Steering Column
GETTING STARTED WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical conditions must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time.
Page 480: Programmable Features
GETTING STARTED PROGRAMMABLE FEATURES Electronic Vehicle Information Center (EVIC) – If Equipped • The EVIC can be used to program the following Personal Settings. Press and release the MENU button until Personal Settings displays, then press the SCROLL button to scroll through the settings. Press the FUNCTION SELECT button change the setting.
Page 481 GETTING STARTED Auto Door Lock • To have the doors lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h): • The auto door lock feature can be enabled or disabled by your authorized dealer. See your authorized dealer for programming. Sound Horn With Lock •...
Page 482: Operating Your Vehicle
OPERATING YOUR VEHICLE TURN SIGNAL/WIPER/WASHER/HIGH BEAM LEVER Turn Signal/Lane Change Assist • Tap the lever up or down once and the turn signal (right or left) will flash three times and automatically turn off. Front Wipers Intermittent, Low And High Operation •...
Page 483: Headlight Switch
OPERATING YOUR VEHICLE HEADLIGHT SWITCH Automatic Headlights/Parking Lights/Headlights • Rotate the headlight switch to the first detent for parking lights and to the second detent for headlights • Rotate the headlight switch to “A” for AUTO headlights. • When set to “A” (AUTO), the system automatically turns the headlights on or off based on ambient light levels.
Page 484: Speed Control Lever
OPERATING YOUR VEHICLE SPEED CONTROL LEVER Cruise ON/OFF • Push the ON/OFF button to activate the Speed Control. • CRUISE will appear on the instrument cluster to indicate the Speed Control is on. • Push the ON/OFF button a second time to turn the system off.
Page 485: Manual Transmission 1 To 4 Skip Shift
OPERATING YOUR VEHICLE MANUAL TRANSMISSION 1 TO 4 SKIP SHIFT • Skip Shift is enabled when vehicle speed is between 19 MPH (30 km/h) and 21 MPH (34 km/h) and the accelerator pedal is at 1/4 throttle or less. • For optimal fuel economy, under low acceleration conditions, your vehicle will only allow you to shift from first gear to fourth gear.
Page 486: Wind Buffeting
OPERATING YOUR VEHICLE WARNING! (Continued) • In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed. Always fasten your seat belt properly and make sure all passengers are properly secured too. •...
Page 487: Electronics
ELECTRONICS NON-TOUCH-SCREEN RADIOS Sales Code RES Sales Code RES/RSC...
Page 488: Audio Settings
ELECTRONICS NOTE: Uconnect™ Phone and Voice Command are vehicle options which must be ordered separately. The buttons on the radio will only be active if the vehicle has been equipped with the option. • The radio sales code is located on the lower right side of the radio faceplate. •...
Page 489 ELECTRONICS TOUCH-SCREEN RADIOS Navigation Radio – Sales Code RER Multimedia Radio – Sales Code REN...
Page 490: Radio Mode
ELECTRONICS Multimedia Radio – Sales Code RBZ NOTE: Uconnect™ Phone and Voice Command are vehicle options which must be ordered separately. The buttons on the radio will only be active if the vehicle has been equipped with the option. • The radio sales code is located on the lower right side of the radio faceplate. •...
Page 491: Store Radio Presets
ELECTRONICS • The display will switch automatically to the AUX mode when a 3.5 mm stereo mini-jack cable has been connected. • To change radio modes while the cable is connected to the unit, press the RADIO/MEDIA (RER and REN) or MEDIA (RBZ) hard-key until the AUX tab is displayed on the top of the screen.
Page 492 ELECTRONICS Copy Pictures To The Hard-Drive • Insert either a CD or a USB device containing your pictures. • Touch the MY FILES soft-key, then go to the MANAGE MY FILES screen. • Touch the MY PICTURES soft-key to get an overview of the currently stored images. •...
Page 493 ELECTRONICS Program/Storing Home Address • Press the NAV hard-key to access the Navigation Main Menu. • Touch the GUIDE ME HOME soft-key, then touch the STREET ADDRESS soft-key. • Touch the STATE soft-key, then enter your state name into the speller; select your state from the list and press the CHANGE soft-key.
Page 494: Remote Audio Controls
ELECTRONICS REMOTE AUDIO CONTROLS • The remote sounds system controls are located on the steering wheel. • Press the top or bottom of the Volume button to increase or decrease the sound level. • Press the Audio Mode button to select radio mode information.
Page 495: Electronic Vehicle Information Center (Evic)
ELECTRONICS ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) • The EVIC features a driver interactive display that is located in the instrument cluster. Pressing the controls on the steering wheel allows the driver to select vehicle information and Personal Settings. For additional information, refer to Programmable Features in this guide.
Page 496: Power Outlet
ELECTRONICS ® • Press and hold the just-trained HomeLink button; if the channel has been trained, the EVIC display will show “CHANNEL # TRANSMIT” and the device should operate. WARNING! • Your motorized door or gate will open and close while you are training the universal transceiver.
Page 497: Uconnect™ Phone
ELECTRONICS • The second outlet in the center console is powered directly from the battery (power available at all times). Items plugged into this outlet may discharge the battery and/or prevent engine starting. NOTE: Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced.
Page 498: Making A Phone Call
ELECTRONICS • You will be asked to create a four-digit PIN which you will later need to enter into your ® phone (typically...settings, Bluetooth , device, list, new). • You will then be prompted to give the phone pairing a name (each phone paired should have a unique name).
Page 499: Voice Command
ELECTRONICS VOICE COMMAND • The Voice Command system allows you to control your AM, FM radio, satellite radio, disc player, and a memo recorder. When you press the Voice Command button , you will hear a beep. The beep is your signal to give a command. If you do not say a command within a few seconds, the system will present you with a list of options.
Page 500: Utility
UTILITY...
Page 501: Recreational Towing (Behind Motorhome, Etc.)
UTILITY RECREATIONAL TOWING BRAKE/TRANSMISSION INTERLOCK MANUAL (BEHIND MOTORHOME, OVERRIDE ETC.) • Recreational towing is allowed ONLY if the driveshaft is removed. Towing with the rear wheels on the ground while the driveshaft is connected can result in severe transmission damage. WARNING! If the driveshaft is removed, the vehicle can roll even if the...
Page 502 UTILITY • Using the screwdriver, reach into • Have your vehicle inspected by your the manual override opening. local authorized dealer if the shift Press and hold the shift lock lever lock manual override has been used. down. • Move the shift lever into the NEUTRAL position and start the vehicle.
Page 503: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES 24 HOUR TOWING ASSISTANCE - U.S. ONLY • Dial toll-free 1-800-521-2779 or 1-800-363-4869 for Canadian residents. • Provide your name, vehicle identification number and license plate number. • Provide your location, including telephone number, from which you are calling. •...
Page 504: Charging System Light
WHAT TO DO IN EMERGENCIES • We recommend that you do not operate the vehicle or engine damage will occur. Have the vehicle serviced immediately. WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant.
Page 505: Oil Pressure Warning Light
WHAT TO DO IN EMERGENCIES • We recommend you do not continue driving if the charging system light is on. Have the vehicle serviced immediately. - Oil Pressure Warning Light • This light indicates low engine oil pressure. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible.
Page 506 WHAT TO DO IN EMERGENCIES Resetting The Light After Servicing • Turn the ignition switch to the ON/RUN position (do not start engine). • Fully depress the accelerator pedal three times within 10 seconds. • Turn the ignition switch to the OFF/LOCK position. IF YOUR ENGINE OVERHEATS •...
Page 507: Jacking, Tire Changing And Tirefit Tire Repair
WHAT TO DO IN EMERGENCIES JACKING, TIRE CHANGING AND TIREFIT TIRE REPAIR WARNING! • Do not attempt to change or seal a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack, changing the wheel or using the TIREFIT kit.
Page 508 WHAT TO DO IN EMERGENCIES Jack/Spare Tire Location TIREFIT Kit Location...
Page 509 WHAT TO DO IN EMERGENCIES • The jack and spare tire or TIREFIT kit are stowed under an access cover in the trunk. • Lift the access cover using the pull strap and remove the fastener securing the spare tire. •...
Page 510 WHAT TO DO IN EMERGENCIES • Place the jack underneath the lift area that is closest to the flat tire. Turn the jack screw clockwise to firmly engage the jack saddle with the lift area of the sill flange. • Raise the vehicle by turning the jack screw clockwise. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire.
Page 511 WHAT TO DO IN EMERGENCIES WARNING! To assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground. • Secure the tire, jack (base of jack faces rear of vehicle), and tools in their proper locations.
Page 512 WHAT TO DO IN EMERGENCIES NOTE: If the tire does not inflate to at least 26 psi pressure within 15 minutes, the tire is too badly damaged. Do not attempt to drive the vehicle further. Call for assistance. • If the tire inflates to the recommended pressure or is at least 26 psi pressure within 15 minutes, press the Power button to turn off the TIREFIT kit.
Page 513 WHAT TO DO IN EMERGENCIES WARNING! Do not use TIREFIT or drive the vehicle under the following circumstances: • If the cut or puncture in the tire tread is approximately 0.24 in (6 mm) or larger. • If the tire has any sidewall damage. •...
Page 514: Jump-Starting
WHAT TO DO IN EMERGENCIES JUMP-STARTING • If your vehicle has a discharged battery it can be jumpstarted using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack. • Jump-starting can be dangerous if done improperly so please follow the procedures in this section carefully.
Page 515 WHAT TO DO IN EMERGENCIES WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • Remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact.
Page 516 WHAT TO DO IN EMERGENCIES WARNING! Do not connect the cable to the negative post (-) of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. • Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then start the engine in the vehicle with the discharged battery.
Page 517 WHAT TO DO IN EMERGENCIES...
Page 518: Freeing A Stuck Vehicle
WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE • If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels.
Page 519 WHAT TO DO IN EMERGENCIES EVENT DATA RECORDER (EDR) • In the event of an accident, your vehicle is designed to record up to five seconds of specific vehicle data parameters (see list below) in an event data recorder prior to the moment of airbag deployment, or near deployment (if applicable), and up to a quarter second of either high-speed deceleration data or change in velocity during and/or after airbag deployment or near-deployment.
Page 520 WHAT TO DO IN EMERGENCIES Data parameters that are recorded: • Diagnostic trouble code(s) and warning light status for electronically-controlled safety systems, including the airbag system • Vehicle speed • Engine RPM • Brake switch status • Pedal position • And other parameters depending on vehicle configuration...
Page 521 MAINTAINING YOUR VEHICLE OPENING THE HOOD • Pull the hood release lever located on the instrument panel, below the steering column. • Raise the hood and locate the safety catch lever, in the middle of the hood opening. • Move the safety latch while lifting the hood at the same time. •...
Page 522: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE...
Page 523 MAINTAINING YOUR VEHICLE...
Page 524 MAINTAINING YOUR VEHICLE...
Page 525: Fluids And Capacities
MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Fluid, Lubricant, or Component Capacities Genuine Part ® Engine Coolant 3.5L MOPAR Antifreeze/ 11.1 Quarts (10.5 Liters) Coolant Five Includes heater and Year/100,000 Mile Formula coolant recovery bottle HOAT (Hybrid Organic filled to MAX level. Additive Technology) or equivalent.
Page 526 MAINTAINING YOUR VEHICLE Fluid, Lubricant, or Component Capacities Genuine Part Spark Plug 3.5L ZFR5LP–13G (Gap 0.050 in — [1.27 mm]) Spark Plug 5.7L LZFR5C–11 (Gap 0.043 in — [1.1 mm]) Spark Plug 6.1L PLZTR5A-13 (Gap.050 in — [1.27 mm]) ® ®...
Page 527 MAINTAINING YOUR VEHICLE...
Page 528: Maintenance Record
MAINTAINING YOUR VEHICLE Maintenance Record Odometer Date Signature, Authorized Service Center 6,000 Miles (10,000 km) or 6 Months 12,000 Miles (20,000 km) or 12 Months 18,000 Miles (30,000 km) or 18 Months 24,000 Miles (40,000 km) or 24 Months 30,000 Miles (50,000 km) or 30 Months 36,000 Miles...
Page 529: Fuses
MAINTAINING YOUR VEHICLE FUSES Integrated Power Module (IPM) • The Integrated Power Module (IPM) is located in the engine compartment on the right hand side near the Washer Fluid Reservoir. This module contains fuses and relays. Cavity Cartridge Fuse Mini-Fuse Description 15 Amp Blue Washer Motor...
Page 530 MAINTAINING YOUR VEHICLE...
Page 531 MAINTAINING YOUR VEHICLE • There is also a power distribution center located in the trunk under the spare tire access panel. This center contains fuses and relays. Cavity Cartridge Fuse Mini-Fuse Description 60 Amp Yellow Ignition Off Draw (IOD) 40 Amp Green Integrated Power Module (IPM) —...
Page 532: Tire Pressures
MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Mini-Fuse Description 5 Amp Orange Antenna Module - if equipped/Power Mirrors 25 Amp Natural Uconnect™ Phone - if equipped/Radio/ Amplifier Feed 15 Amp Blue Transmission 10 Amp Red Cargo Light/Vehicle Information Module - if equipped 10 Amp Red Heated Mirrors - if equipped 5 Amp Orange...
Page 533: Wheel And Wheel Trim Care
MAINTAINING YOUR VEHICLE WHEEL AND WHEEL TRIM CARE • All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. ® • To remove heavy soil and/or excessive brake dust, use MOPAR Wheel Cleaner or equivalent or select a non-abrasive, non-acidic cleaner.
Page 534: Consumer Assistance
Voice callers, dial 1–800–855–0511 to connect with a Bell Relay Service NOTE: A street address is required operator. when ordering manuals (no P.O. Boxes). NOTE: • The Owner's Manual and User Guide electronic files are also available on the Chrysler, Jeep and Dodge websites.
Page 535: Reporting Safety Defects In The 50 United States And Washington, D.c
CONSUMER ASSISTANCE In Canada • Click on the "For Owners" tab, select "Owner/Service Manuals", then • If you believe that your vehicle has a select your desired model year and safety defect, you should contact the vehicle from the drop down lists. Customer Service Department immediately.
Page 536 CONSUMER ASSISTANCE Disclaimer: WARNING! (Continued) • THE TIRE MANUFACTURER’S LIMITED • Tires should be inspected regularly WARRANTY PROGRAM, THE DETAILS by a qualified technician for signs OF WHICH CAN BE FOUND, ON THE of damage, such as punctures, OWNERS MANUAL DVD, THE TIRE impacts, under-inflation or MANUFACTURER’S WEBSITE OR AT overloading.
Page 537 CONSUMER ASSISTANCE Using Lift Kits WARNING! • Use of lift kits with some vehicle/tire Tires and the spare tire should be combinations can cause instability or replaced after six years, regardless of loss of control. When changing tire the remaining tread. Failure to follow sizes, always consult an installer for this warning can result in sudden tire optimum rim width and carefully...
Page 538: Mopar Accessories
• The following highlights just some of the authentic Dodge Accessories by MOPAR that have been engineered to customize your Dodge Challenger. • To see the full line of accessories, stop by your Dodge dealer or visit MOPAR.com. CHROME: • Chrome Fuel Filler Door •...
Page 539 NOTES...
Page 541 DODGE.com This guide has been prepared to help you get quickly acquainted with your new Dodge and to provide a convenient reference source for common questions. However, it is not a substitute for your Owner’s Manual. For complete operational instructions, maintenance procedures and important safety messages, please consult your Owner’s...

Dodge Challenger 2009 Owner's Manual

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Quick Links

Chapters

Related Manuals for Dodge Challenger 2009

Summary of Contents for Dodge Challenger 2009