Page 2 VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents.
Page 3: Introduction
TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 5: Table Of Contents
CONTENTS Introduction ......4 How To Use This Manual ....4 Warnings And Cautions .
Page 6: Introduction
4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully.
Page 7 INTRODUCTION 5...
Page 8: Vehicle Identification Number
This VIN Location number also appears on the Automobile Information NOTE: It is illegal to remove the VIN. Disclosure Label affixed to a window on your vehicle, the...
Page 9: Vehicle Modifications/Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 11 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Wireless Ignition Node (WIN) ... . .12 FOB With Integrated Key .
Page 12 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Using The Panic Alarm ....24 Express Down Window Feature ... .25 Programming Additional Transmitters .
Page 13 Driver And Front Passenger Supplemental Restraint System (SRS) - Airbag ... .50 Event Data Recorder (EDR) ....63 Child Restraint .
Page 14: Things To Know Before Starting Your Vehicle 9
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Your vehicle uses a keyless ignition system. This system consists of a Fob with Integrated Key and a Wireless Ignition Node (WIN) with integral ignition switch. You can insert the double-sided integrated key into the igni- tion switch with either side up.
Page 15: Fob With Integrated Key
Fob With Integrated Key The Fob with Integrated Key operates the ignition switch. It also contains the Remote Keyless Entry (RKE) trans- mitter and a valet key, which stores in the rear of the Fob. The valet key allows for entry into the vehicle should the battery in the vehicle or the Fob go dead.
Page 16: Tip Start Feature
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Tip Start Feature Do not press the accelerator. Use the Fob with Integrated Key to briefly turn the ignition switch to the START position and release it as soon as the starter engages. The starter motor will continue to run, and it will disengage automatically when the engine is running.
Page 17: Key-In-Ignition Reminder
CAUTION! An unlocked car is an invitation to thieves. Always remove the key from the ignition and lock all doors when leaving the vehicle unattended. Key-In-Ignition Reminder If you open the driver’s door and the key is in the ignition, a chime will sound to remind you to remove the key.
Page 18: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE indicates that there is a problem with the electronics. This condition will result in the engine being shut off after two seconds. If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than 10 seconds), it indicates that there is a fault in the electron- ics.
Page 19: Customer Key Programming
At the time of purchase, the original owner is provided with a four-digit Personal Identification Number (PIN). Keep the PIN in a secure location. This number is required for authorized dealer replacement of RKE trans- mitters. Duplication of RKE transmitters may be per- formed at an authorized dealer or by using the Customer Key Programming procedure.
Page 20: General Information
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The new integrated key is programmed. The RKE trans- mitter will also be programmed during this procedure. Repeat this procedure to program up to eight keys. If you do not have a programmed RKE transmitter with inte- grated key, contact your authorized dealer for details.
Page 21: To Arm The System
To Arm the System 1. Remove the key from the ignition switch and exit the vehicle. 2. Lock the doors and liftgate by pressing the power door LOCK switch or the LOCK button on the Remote Keyless Entry (RKE) transmitter. NOTE: The system will not arm if you lock the doors with the manual door LOCK plungers or the door LOCK cylinder on the driver’s door.
Page 22: Illuminated Entry System
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE arm regardless of whether you are inside or outside the vehicle. If you remain inside the vehicle and open a door, the alarm will sound. If this occurs, disarm the system. Tamper Alert If something has triggered the alarm in your absence, the horn will sound three times when you unlock the doors.
Page 23: To Unlock The Doors And Liftgate
Remote Keyless Entry (RKE) Transmitter To Unlock the Doors and Liftgate Press and release the UNLOCK button on the transmitter once to unlock the driver’s door, or twice within five seconds to unlock all doors and liftgate. The turn signal lights will flash to acknowledge the unlock signal.
Page 24 22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Test the feature while outside of the vehicle by press- ing the LOCK/UNLOCK buttons on the transmitter with the ignition switch in the LOCK position and the key removed. 4. Repeat these steps if you want to return this feature to its previous setting.
Page 25: To Lock The Doors And Liftgate
NOTE: Pressing the LOCK button on the transmitter while you are in the vehicle will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm. Illuminated Approach —...
Page 26: Using The Panic Alarm
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Test the feature while outside of the vehicle by press- ing the LOCK button on the transmitter with the ignition switch in the LOCK position and the key removed. 4. Repeat these steps if you want to return this feature to its previous setting.
Page 27: Express Down Window Feature
Express Down Window Feature This feature allows you to remotely lower both front door windows at the same time. To use this feature, press and release the unlock button on the transmitter and then immediately press and hold the unlock button until the windows lower to the level desired or until they lower completely.
Page 28: General Information
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Battery Replacement 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3.
Page 29: Remote Starting System - If Equipped
REMOTE STARTING SYSTEM — IF EQUIPPED This system uses the Remote Keyless Entry (RKE) trans- mitter to start the engine conveniently from outside the vehicle while still maintaining security. The system has a targeted range of 328 ft (100 m). NOTE: The vehicle must be equipped with an auto- matic transaxle to be equipped with Remote Start.
Page 30: Door Locks
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE For security, power window and power sunroof op- eration (if so equipped) are disabled when the vehicle is in the Remote Start mode. The engine can be started two consecutive times (two 15-minute cycles) with the RKE transmitter.
Page 31 Door Lock Plunger If the door lock plunger is down when you shut the door, the door will lock. Therefore, make sure the key is not inside the vehicle before closing the door. NOTE: The manual door locks will not lock or unlock the liftgate.
Page 32: Power Door Locks
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks A power door lock switch is on each front door trim panel. Use this switch to lock or unlock the doors and liftgate. Power Door Lock Switch To prevent you from locking your key in the vehicle, the power door lock switch will not operate when the key is in the ignition and either front door is open.
Page 33 Automatic Door Locks — If Equipped The auto door lock feature can be enabled or disabled by your authorized dealer. See your authorized dealer for programming. Automatic Unlock Doors on Exit The doors will unlock automatically if: 1. The Automatic Unlock Doors On Exit feature is en- abled 2.
Page 34: Child Protection Door Lock System (Rear Doors)
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Within 30 seconds, depress the power door unlock switch to unlock the doors. 5. A single chime will indicate the completion of the programming. NOTE: If you do not hear the chime, it means that the system did not enter the programming mode and you will need to repeat the procedure.
Page 35 NOTE: When the Child Protection Door Lock system is engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position. WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged.
Page 36: Windows
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Lock Control 3. Repeat Steps 1 and 2 for the opposite rear door. NOTE: After disengaging the Child Protection Door Lock system, always test the door from the inside to make certain it is in the desired position. WINDOWS Power windows The window controls on the driver’s door trim panel...
Page 37 There are single window controls on each passenger door trim panel, which operate the passenger door windows. The window controls will operate when the ignition switch is in the ON or ACC position. NOTE: For vehicles not equipped with the Electronic Vehicle Information Center (EVIC), the power window switches will remain active for 45 seconds after the ignition switch is turned to the LOCK position.
Page 38 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To open the window part way, press the window switch to the first detent and release it when you want the window to stop. To stop the window from going all the way down during the Auto-down operation, pull up on the switch briefly.
Page 39: Wind Buffeting
Window Lockout Switch The window lockout switch on the driver’s door trim panel allows you to disable the window control on the other doors. To disable the window controls, press and release the window lockout button (setting it in the down position).
Page 40: Liftgate
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the rear windows open, then open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sun- roof opening to minimize the buffeting or open any window.
Page 41: Occupant Restraints
WARNING! Driving with the liftgate open can allow poison- ous exhaust gases into your vehicle. These fumes could injure you and your passengers. Keep the liftgate closed when you are operating the vehicle. If you are required to drive with the liftgate open, make sure that all windows are closed, and the blower switch on the climate control is set at high speed.
Page 42 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you will be carrying children too small for adult-size belts, your seat belts or the Lower Anchors and Tether for Children (LATCH) feature can also be used to hold infant and child restraint systems. Please pay close attention to the information in this section.
Page 43: Lap/Shoulder Belts
Lap/Shoulder Belts All seating positions in your vehicle are equipped with lap/shoulder belts. The belt webbing retractor is designed to lock during very sudden stops or impacts. This feature allows the shoulder part of the belt to move freely with you under normal conditions.
Page 44 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the front seat. 2. The seat belt latch plate is along side the pillar near the back of your seat.
Page 45 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Connecting Latch Plate To Buckle THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 WARNING! A belt that is buckled into the wrong buckle will not protect you properly.
Page 46 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up a bit on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt.
Page 47 WARNING! A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as pos- sible and keep it snug.
Page 48 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the driver’s seat and front passenger’s seat, the shoul- der belt can be adjusted upward or downward to posi- tion the belt away from your neck. Push and fully depress the button above the webbing to release the anchorage, then move it up or down to the position that fits you best.
Page 49: Lap/Shoulder Belt Untwisting Procedure
you will prefer a higher position. When you release the anchorage try to move it up and down to make sure that it is locked in position. In the rear seat, move toward the center of the seat to position the belt away from your neck. Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt.
Page 50: Enhanced Seat Belt Reminder System (Beltalert )
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Seat Belt Reminder System (BeltAlert ) If the driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert ) will alert the driver to buckle the seat belt.
Page 51: Automatic Locking Mode
4. Turn the ignition switch to the LOCK position. A single chime will sound to signify that you have success- fully completed the programming. The BeltAlert can be reactivated by repeating this pro- cedure. NOTE: When the BeltAlert is deactivated, the Seat Belt Reminder Light will continue to illuminate as long as the driver’s seat belt is unbuckled/retracted.
Page 52: Seat Belts And Pregnant Women
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belts and Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible.
Page 53 1 — Driver’s Airbag 2 — Front Passenger’s Airbag 3 — Knee Bolsters NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity.
Page 54 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE This vehicle also has supplemental side curtain airbags to protect the driver and passengers sitting next to a win- dow and supplemental front seat mounted side airbags. The supplemental side curtain airbags are located above the side windows.
Page 55 WARNING! Do not stack luggage or other cargo up high enough to block the location of the side curtain airbag. The area where the side curtain airbag is located should remain free from any obstructions. Do not have any accessory items installed which will alter the roof, including adding a sunroof to your vehicle.
Page 56 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some simple steps you can take to minimize the risk of harm from a deploying airbag. 1. Children 12 years old and younger should ride buck- led up in the rear seat. WARNING! Infants in rear-facing child restraints should NEVER ride in the front seat of a vehicle with a passenger...
Page 57 8. Do not lean against the door, as the supplemental side curtain airbags and supplemental front seat mounted side airbags will inflate forcefully into the space between you and the door. 9. If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center.
Page 58 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag System Components The airbag system consists of the following: Occupant Restraint Controller (ORC) Side Remote Pressure and Acceleration Sensors Airbag Warning Light Driver Airbag Front Passenger Airbag Supplemental Side Curtain Airbags Supplemental Front Seat Mounted Side Airbags Steering Wheel and Column Instrument Panel...
Page 59 The ORC and other systems monitor the readiness of the electronic components whenever the ignition switch is in the START or ON position. These include all of the items listed above except the knee impact bolsters, the instrument panel, and the steering wheel and column.
Page 60 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE panel separate and fold out of the way as the bags inflate to their full size. The bags fully inflate in about 50 to 70 ms. This is about half of the time that it takes to blink your eyes.
Page 61 between the occupant and the door. The airbag inflates at a very high speed and with enough force to injure you if you are not belted and seated properly, or if items are positioned in the area where the front seat mounted side airbag inflates.
Page 62 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Unapproved modifications or service procedures to the front seat assembly, its related components, or seat cover may inadvertently change the airbag de- ployment in case of a frontal crash. This could result in death or serious injury to the driver or front seat passenger if the vehicle is involved in an accident.
Page 63 As the airbags deflate, you may see some smoke-like particles. The particles are a normal by-product of the process that generates the nontoxic gas used for airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water.
Page 64 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Turns on the interior lights, which remain on as long as the battery has power or until the ignition key is removed. Unlocks the doors automatically. NOTE: The interior lights can only be deactivated if the key is removed from the ignition switch or the vehicle is driven.
Page 65: Event Data Recorder (Edr)
NOTE: Perchlorate Material — special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate. Airbag Warning Light You will want to have the airbags ready to inflate for your protection in an impact. While the airbag system is designed to be mainte- nance free, if any of the following occurs, have an authorized dealer service the system promptly: The Airbag Warning Light does not come on or flickers during the four to six seconds when the ignition...
Page 66 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In conjunction with other data gathered during a com- plete accident investigation, the electronic data may be used by the manufacturer of this vehicle and others to learn more about the possible causes of crashes and associated injuries in order to assess and improve vehicle performance.
Page 67: Child Restraint
Data Parameters that May Be Recorded: Diagnostic trouble code(s) and warning light status for electronically-controlled safety systems, including the airbag system Airbag disable light status (if equipped) Time of airbag deployment (in terms of ignition cycles and vehicle mileage) Airbag deployment level (if applicable) Impact acceleration and angle Seat belt status Brake status (service and parking brakes)
Page 68 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.
Page 69 “LATCH — Child Seat Anchor System (Lower An- chors and Tether for CHildren)” in this section. Rearward-facing child seats must NEVER be used in the front seat of a vehicle with the front passenger airbag unless the airbag is turned off. An airbag deployment could cause severe injury or death to infants in this position.
Page 70 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To position a child into the Integrated Child Booster Seat follow these steps: 1. Pull the release loop forward to release the latch and seat cushion. 2. Lift the seat cushion up and push back to lock it in the booster seat position.
Page 71 NOTE: The lap portion of the seat belt should be low on the hips and as snug as possible. 6. Once the seat belt is long enough to fit properly, insert the latch plate into the buckle until you hear a “click.” 7.
Page 72 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The lap portion should be low on the hips and as snug as possible. Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle.
Page 73 Here are some tips on getting the most out of your child restraint: Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. We also recommend that you make sure that you can install the child restraint in the vehicle where you will use it before you buy it.
Page 74 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE connection to the top tether anchors have been available for some time. For some older child restraints, many child restraint manufacturers offer add-on tether strap kits or retrofit kits. You are urged to take advantage of all the available attachments provided with your child re- straint in any vehicle.
Page 75 Installing the LATCH-Compatible Child Restraint System We urge you to follow the manufacturer’s directions carefully when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that are provided with the child restraint system. The lower anchors are round bars located at the rear of the seat cushion where it meets the seatback and are just visible when you lean...
Page 76 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE hook for attachment to the tether strap anchor and a means of adjusting the tension of the strap. You will first loosen the adjusters on the lower straps and on the tether strap so that you can more easily attach the hooks or connectors to the vehicle anchors.
Page 77 WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. Installing Child Restraints Using the Vehicle Seat Belt The seat belts in the passenger seating positions are...
Page 78 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Tether Strap Mounting If necessary, move the seat forward to provide better access to the tether anchor. Seat Track Release Lever Attach the tether strap hook of the child restraint to the tether anchor and remove slack in the tether strap according to the child restraint manufacturer’s instruc- tions.
Page 79: Engine Break-In Recommendations
NOTE: Ensure that the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap. WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap.
Page 80: Safety Tips
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE “Maintenance Procedures” DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE USED. A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of difficulty.
Page 81: Lock Your Vehicle
Lock Your Vehicle Always remove the key from the ignition and lock all doors when leaving the vehicle unattended, even in your own driveway or garage. Try to park your vehicle in a well-lit area and never invite theft by leaving articles of value exposed.
Page 82: Safety Checks You Should Make Inside The Vehicle
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.
Page 83: Periodic Safety Checks You Should Make Outside The Vehicle
Periodic Safety Checks You Should Make Outside The Vehicle Tires Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread. Inspect the tread and sidewall for cuts and cracks. Check the wheel nuts for tightness. Check the tires (including spare) for proper pressure.
Page 85 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors .......88 Inside Day/Night Mirror ....88 Automatic Dimming Inside Mirror —...
Page 86 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information ....120 Voice Recognition System — If Equipped ..120 Voice Recognition System (VR) Operation .
Page 87 Flash To Pass ......150 Interior Lights ..... . . 151 Windshield Wipers And Washers .
Page 88 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using HomeLink ..... 168 Reprogramming A Single HomeLink Button ......168 Security .
Page 89 Storage ......180 Beverage Cooler/Storage Compartment — If Equipped ......180 Instrument Panel Storage Compartment —...
Page 90: Mirrors
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical mirror adjustment. Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).
Page 91: Automatic Dimming Inside Mirror
Automatic Dimming Inside Mirror — If Equipped This mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light will illuminate next to the switch when the automatic dimming feature is activated.
Page 92: Outside Mirrors Folding Feature - If Equipped
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicles and other objects seen in the passenger-side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger-side convex mirror could cause you to collide with another vehicle or other object.
Page 93: Heated Remote Control Mirrors - If Equipped
Models with Express Window Feature Press and release the mirror SELECT button marked L or R and then press one of the four arrow buttons to move the mirror in the direction the arrow is pointing. The selection times out after 30 seconds of inactivity in order to guard against accidentally changing a mirror position following an adjustment.
Page 94: Parkview Rear Backup Camera - If Equipped
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Pull the sun visor toward the inside rearview mirror to extend it. PARKVIEW REAR BACKUP CAMERA — IF EQUIPPED The Parkview Rear Backup Camera captures live video of the area behind the vehicle. The live video displays on the radio’s display screen when backing up your vehicle.
Page 95: Hands-Free Communication (Uconnect ) - If Equipped
CAUTION! To avoid vehicle damage, only use the Rear Backup Camera as a parking aid, as the camera is unable to capture every obstacle or object in your drive path. To avoid vehicle damage, drive slowly when back- ing up a vehicle so that you can stop in time when an obstacle comes into view.
Page 96 For UConnect customer support, visit the NOTE: following websites: www.chrysler.com/uconnect www.dodge.com/uconnect www.jeep.com/uconnect or call 1–877–855–8400 UConnect allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle and enables you to mute the system’s microphone for private conversation.
Page 97: Operation
Phone Button The rearview mirror contains the microphone for the system (depending on the type of mirror and radio equipped), and either the radio or the mirror has the two control buttons (PHONE Button and VOICE RECOGNITION button) that will enable you to access the system. Voice Recognition Button Actual button location may vary with radio.
Page 98 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE For certain operations, compound commands can be used. For example, instead of saying Setup and then Phone Pairing, the following compound command can be said: Setup Phone Pairing. For each feature explanation in this section, only the combined form of the voice command is given.
Page 99 To complete the pairing process, you will need to refer- ence your cellular phone Owner’s Manual. The UConnect website may also provide detailed instruc- tions for pairing. The following are general phone to UConnect system pairing instructions: Press the PHONE button to begin. After the Ready prompt and the following beep, say Setup Phone Pairing.
Page 100 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dial by Saying a Number Press the PHONE button to begin. After the Ready prompt and the following beep, say Dial. The system will prompt you to say the number you want to call. For example, you can say 234-567-8901.
Page 101 Add Names to Your UConnect Phonebook NOTE: Adding names to the phonebook is recom- mended when the vehicle is not in motion. Press the PHONE button to begin. After the Ready prompt and the following beep, say Phonebook New Entry. When prompted, say the name of the new entry.
Page 102 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Object Exchange Profile (OBEX). Please see your phone Owner’s Manual for specific instructions on how to send these entries from your phone. NOTE: The phone handset must support Bluetooth OBEX transfers of phonebook entries to use this feature. Some phones cannot send phonebook entries if they are already connected to any system via Bluetooth , and you may see a message on the phone display that...
Page 103 Phonebook Edit can be used to add another phone number to a name entry that already exists in the phonebook. For example, the entry John Doe may have a mobile and a home number, but you can add ”John Doe’s” work number later using the Phonebook Edit feature.
Page 104: Phone Call Features
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE After confirmation, the phonebook entries will be deleted. Note that only the phonebook in the current language is deleted. List All Names in the UConnect Phonebook Press the PHONE button to begin. After the Ready prompt and the following beep, say Phonebook List Names.
Page 105 the call, press and hold the PHONE button until you hear a single beep, indicating that the incoming call was rejected. Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your cell phone.
Page 106 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Conference Call When two calls are in progress (one active and one on hold), press and hold the PHONE button until you hear a double beep indicating that the two calls have been joined into one conference call.
Page 107: Uconnect System Features
After the ignition key is switched to OFF, a call can continue on the UConnect system either until the call ends, or until the vehicle battery condition dictates cessation of the call on the UConnect system and transfer of the call to the mobile phone. After the ignition key is switched to OFF, a call can continue on the UConnect system for a certain dura- tion, after which the call is automatically transferred...
Page 108 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the phone is not reachable and the UConnect system is operational, you may reach the emergency number as follows: Press the PHONE button to begin. After the Ready prompt and the following beep, say Emergency and the UConnect system will instruct the paired cellular phone to call the emergency num- ber.
Page 109 Paging To learn how to page, refer to Working with Automated Systems. Paging works properly except for pagers of certain companies, which time out a little too soon to work properly with the UConnect system. Voice Mail Calling To learn how to access your voice mail, refer to Working with Automated Systems.
Page 110 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE send the corresponding phone number associated with the phonebook entry, as tones over the phone. NOTE: You may not hear all of the tones due to cellular phone network configurations; this is normal. Some paging and voice mail systems have system time out settings that are too short and may not allow the use of this feature.
Page 111 Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the UConnect system (while dial- ing via the cell phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired Bluetooth cellular phone, the audio will be played through your vehicle’s audio system.
Page 112: Advanced Phone Connectivity
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Advanced Phone Connectivity Transfer Call to and from Cellular Phone The UConnect system allows ongoing calls to be trans- ferred from your cellular phone to the UConnect system without terminating the call. To transfer an ongoing call from your UConnect paired cellular phone to the UConnect system or vice versa, press the “Voice Recog-...
Page 113: Things You Should Know About Your Uconnect System
After the Ready prompt and the following beep, say Setup Select Phone and follow the prompts. You can also press the “Voice Recognition” button at any time while the list is being played, and then choose the phone that you wish to select. The selected phone will be used for the next phone call.
Page 114 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE From outside the UConnect mode (e.g., from radio mode): Press and hold the “Voice Recognition” button for five seconds until the session begins, or, Press the “Voice Recognition” button and say the Setup, Voice Training command. Repeat the words and phrases when prompted by the UConnect system.
Page 115 fully closed windows, dry weather condition. Even though the system is designed for users speaking in North American English, French, and Spanish ac- cents, the system may not always work for some. When navigating through an automated system such as voice mail, or when sending a page, at the end of speaking the digit string, make sure to say Send.
Page 116 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE dry weather conditions, and operation from the driver’s seat. Performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the UConnect system. Echo at the far end can sometimes be reduced by lowering the in-vehicle audio volume.
Page 117 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115...
Page 118 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 119 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117...
Page 120 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Primary Alternate(s) zero three four five seven eight nine star (*) plus (+) pound (#) add location Voice Commands Primary Alternate(s) call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol...
Page 121 Voice Commands Primary Alternate(s) language list names list phones mobile mute mute off new entry pager pair a phone phone pairing pairing phonebook phone book previous record again redial UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 Voice Commands Primary Alternate(s) return to main menu return or main menu select phone...
Page 122: General Information
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired op- eration.
Page 123: Commands
Pressing the VR hard-key while the system is speaking is known as “barging in.” The system will be interrupted and you can add or change commands. This will become helpful once you start to learn the options. NOTE: At any time, you can say the words CANCEL, HELP, or MAIN MENU.
Page 124 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Main Menu Start a dialogue by pressing the VR hard-key. You may say MAIN MENU to switch to the main menu. In this mode, you can say the following commands: RADIO (to switch to the radio mode) DISC (to switch to the disc mode) MEMO (to switch to the memo recorder) Radio AM (or Radio Long Wave or Radio Medium...
Page 125 NEXT CHANNEL (to select the next channel) PREVIOUS CHANNEL (to select the previous chan- nel) LIST CHANNEL (to hear a list of available channels) SELECT NAME (to say the name of a channel) RADIO MENU (to switch to the radio menu) MAIN MENU (to switch to the main menu) Disc To switch to the disc mode say DISC.
Page 126: Voice Training
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE − PREVIOUS (to play the previous memo) − DELETE (to delete a memo) DELETE ALL (to delete all memos) NOTE: Keep in mind that you have to press the VR hard-key first and wait for the beep, before speaking the “barge in”...
Page 127 Manual Seat Adjustment UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be adjusted properly and you could be injured. Adjust any seat only while the vehicle is parked.
Page 128 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be adjusted properly and you could be injured. Adjust the seat only while the vehicle is parked.
Page 129 Lumbar Support — If Equipped The control lever is on the outboard side of the seatback. Turn the control lever downward to increase the lumbar support or upward to decrease the lumbar support as desired. Lumbar Control UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Driver’s Seat Height Adjustment —...
Page 130 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fold Flat Front Passenger Seat — If Equipped This feature allows for extended cargo space. When the seat is folded flat, it is an extension of the load floor surface (allowing long cargo to fit from the rear hatch up to the instrument panel).
Page 131: Power Seat - If Equipped
Pull upward on the lever to fold or unfold the seat. Seatback Release UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. Adjust any seat only while the vehicle is parked.
Page 132: Head Restraints
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Seat Switch CAUTION! Do not place any article under any seat as it may cause damage to the seat controls. WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control.
Page 133 Adjustable Head Restraint To remove the head restraint, you must press the lock release button on the left sleeve and the right sleeve simultaneously. To reinstall the head restraint, insert the posts into the sleeves and push the head restraint down- ward until it locks in place.
Page 134: Heated Seats - If Equipped
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Third Row Passenger Seats — Seven Passenger Models These head restraints are non-adjustable and non- removable. However, you can fold them forward when they are not in use by passengers. Refer to “50/50 Split Third-Row Passenger Seats with Fold-Flat Feature”...
Page 135 Heated Seat Switch Press the switch once to select high-level heating. Press the switch a second time to select low-level heating. Press the switch a third time to shut OFF the heating elements. If high level heating is selected, the system automatically switches to low level heating and turns one indicator light off after 30 minutes of continuous operation.
Page 136: 60/40 Split Second-Row Passenger Seats
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 60/40 Split Second-Row Passenger Seats To provide additional storage area, each second-row passenger seat can be folded flat. This allows for ex- tended cargo space and still maintains some seating room if needed. NOTE: Prior to folding the second-row passenger seat, make sure the front seatback is not in a reclined position.
Page 137 To Fold the Seat 1. Locate the control lever on the lower outboard side of the seat. Seatback Release 2. Place one hand on the seatback and apply a gentle pressure. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 3. Lift the control lever with the other hand, allow the seatback to move forward slightly, and then release the lever.
Page 138 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Be certain that the seatback is locked securely into position. Otherwise, the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury. Forward and Rearward Adjustment The control lever is on the outboard side of the seat.
Page 139 WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be adjusted properly and you could be injured. Adjust any seat only while the vehicle is parked. Recliner Adjustment The control lever is on the outboard side of the seat.
Page 140 138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be adjusted properly and you could be injured. Adjust the seat only while the vehicle is parked.
Page 141 Raise the 20% seatback/armrest and lock it in place when not in use or when additional seating area is required. WARNING! Keep the latch clean and free of objects and be certain that the seatback is locked securely into position. Otherwise, the seat will not provide the proper stability for child seats and/or passengers.
Page 142 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tip n Slide Seat™ Grab Handle NOTE: A hand-grip is molded into the front of each quarter trim panel near the door opening to assist entry and exit from the third-row passenger seats.
Page 143: 50/50 Split Third-Row Passenger Seats With Fold-Flat Feature - Seven Passenger Models
WARNING! Do not drive the vehicle with the seat in this posi- tion, as it is only intended for entering and exiting the third row seats. Failure to follow this warning may result in personal injury. To Unfold and Move the Second-Row Passenger Seat Rearward 1.
Page 144 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Fold the Seat Pull the latch release-loop located at the top of the seatback upward, push the seat forward slightly, and release the release-loop. Then, continue to push the seat forward. The head restraints will fold automatically as the seat moves forward.
Page 145 The seatback can also be locked in a reclined position. To do so, pull the latch release-loop located at the top of the seatback upward, allow the seatback to recline, and release the release-loop. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 WARNING! Be certain that the seatback is locked securely into position.
Page 146: To Open And Close The Hood
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD Two latches must be released to open the hood. First, pull the hood release lever located under the left side of the instrument panel. Hood Release Outside of the vehicle, locate the safety latch lever near the center of the grille between the grille and hood opening.
Page 147 Use the hood prop rod to secure the hood in the open position. Place the upper end of the prop rod in the hole on the underside of the hood. Hood Prop Rod UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 To prevent possible damage: Before closing hood, make sure the hood prop rod is fully seated into its storage retaining clips.
Page 148: Lights
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Exterior and Interior Lighting Control The multifunction lever on the left side of the steering column controls the operation of the headlights, parking lights, turn signal lights, in- strument panel lights, instrument panel light dimming, interior lights, and fog lights (if equipped).
Page 149: Automatic Headlights - If Equipped
Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels. To turn the system ON, turn the end of the multifunction lever to the AUTO position (third detent). When the system is on, the headlight time delay feature is also on.
Page 150: Daytime Running Lights (Drl) - If Equipped
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you turn the headlights, or parking lights, or ignition switch ON again, the system will cancel the delay. If you turn the headlights OFF before the ignition, they will turn off in the normal manner. The headlight delay time is programmable on vehicles equipped with the EVIC.
Page 151: Turn Signals
Front Fog Light NOTE: The front fog lights will only operate with the headlights on low beam. Selecting high beam headlights will turn off the front fog lights. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 Turn Signals Move the multifunction lever upward or downward and the corresponding turn signal indicator on the instru- ment panel will flash to show proper operation of the front and rear turn signal lights.
Page 152: Highbeam/Lowbeam Select Switch
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE You can signal a lane change by moving the lever upward or downward partially without moving beyond the de- tent. NOTE: If either turn signal indicator has a very fast flash rate, check for an inoperative outside light bulb. If an indicator fails to light when the lever is moved, see your authorized dealer for service.
Page 153: Interior Lights
NOTE: If the multifunction lever is held in the Flash to Pass position for more than 15 seconds, the high beams will shut off. If this occurs, wait 30 seconds before activating the Flash to Pass function again. Interior Lights Courtesy/Reading Lights Models with Overhead Console These lights are mounted in the overhead console be-...
Page 154 152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Battery Saver Feature To protect the battery, the interior lights will turn off automatically within 10 minutes of turning the ignition switch to the LOCK position. This will occur if the interior lights were switched ON manually or are on because a door is open.
Page 155: Windshield Wipers And Washers
Parade Mode (Daytime Brightness Feature) Rotate the Dimmer Control to the first detent to brighten the odometer and radio display when the parking lights or headlights are on during daylight conditions. Interior Light ON Rotate the Dimmer Control completely upward to the second detent to turn ON the interior lights.
Page 156 154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rotate the end of the lever to the first detent past the intermittent settings for low speed wiper operation, or to the second detent past the intermittent settings for high speed wiper operation. NOTE: The wipers will automatically return to the park position if you turn OFF the ignition switch while they are operating.
Page 157: Intermittent Wiper System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 Intermittent Wiper System Use the intermittent wiper system when weather condi- tions make a single wiping cycle with a variable pause between cycles desirable. Rotate the end of the Wind- shield Wiper/Washer control lever to the first detent, and then turn the end of the lever to select the desired delay interval.
Page 158: Headlights With Wipers (Available With Auto Headlights Only)
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights with Wipers (Available with Auto Headlights Only) When this feature is active, the headlights will turn on approximately 10 seconds after the wipers are turned ON if the multifunction lever (on the left side of the steering column) is placed in the (A) AUTO position.
Page 159: Adding Washer Fluid
WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use.
Page 160 158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tilt/Telescoping Steering Wheel Lock To unlock the steering column, push the control handle downward. To tilt the steering column, move the steering wheel upward or downward as desired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired.
Page 161: Electronic Speed Control - If Equipped
ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over the accelerator operation at speeds greater than 25 mph (40 km/h). Electronic Speed Control Operation The speed control lever is located on the right side of the steering wheel. Speed Control Lever UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 To Activate...
Page 162: To Set At A Desired Speed
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you are not using it.
Page 163: To Vary The Speed Setting
To Vary the Speed Setting When the speed control is set, you can increase speed by pushing up and holding the lever in RESUME ACCEL. Release the lever when the desired speed is reached, and the new set speed will be established. Tapping RESUME ACCEL once will result in a 1 mph (1.6 km/h) speed increase.
Page 164: Overhead Console
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Speed Control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.
Page 165: Sunglasses Storage
Sunglasses Storage To access the storage compartment, press on the raised bars on the compartment door in the center of the console and release and the door will swing downward. Interior Observation Mirror The convex interior observation mirror provides the driver and front seat passenger a wide field of view to conveniently view passengers sitting in the rear passen- ger seats.
Page 166 164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE HomeLink Buttons NOTE: HomeLink is disabled when the Vehicle Secu- rity Alarm is active. WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate.
Page 167: Programming Homelink
WARNING! Vehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run your vehicle in the garage while training the transceiver. Exhaust gas can cause seri- ous injury or death. Programming HomeLink Before You Begin If you have not trained any of the HomeLink buttons, erase all channels before you begin training.
Page 168 166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Some gate operators and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator/Canadian Programming” section. After training a HomeLink channel, if the garage door does not operate with HomeLink and the ga- rage door opener was manufactured after 1995, the garage door opener may have a rolling code.
Page 169: Gate Operator/Canadian Programming
1 — Garage Door Opener 2 — Training Button 6. Firmly press and release the “Learn” or “Training” button. The name and color of the button may vary by manufacturer. NOTE: There are 30 seconds in which to initiate the next step after the “Learn”...
Page 170: Using Homelink
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner. It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor.
Page 171: Security
3. Without releasing the button, proceed with Program- ming Homelink Step 2 and follow all remaining steps. Security It is advised to erase all channels before you sell or turn in your vehicle. To do this, press and hold the two outside buttons for 20 seconds until the red indicator flashes.
Page 172: Power Sunroof - If Equipped
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for compli- ance could void the user’s authority to operate the device.
Page 173: Opening Sunroof - Manually
WARNING! Never leave children in a vehicle, with the key in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof.
Page 174: Closing Sunroof - Express
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the switch in the forward position, the sunroof will close fully and then stop automatically. Release the switch once the sunroof stops moving. Closing Sunroof - Express Press the switch forward and release, and the sunroof will close automatically from any position.
Page 175: Sunshade Operation
Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. NOTE: The sunshade cannot be closed if the sunroof is open. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears.
Page 176: Sunroof Fully Closed
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunroof Fully Closed Press the switch forward and release to ensure that the sunroof is fully closed. ELECTRICAL POWER OUTLETS There are two fused 12-Volt power outlets located in the center console below the radio. The outlet on the top has power available when the ignition switch in the ON or ACC position.
Page 177 A third fused 12-Volt power outlet is located on the back of the center console. This outlet has power available when the ignition switch is in the LOCK, ON or ACC position. Rear Power Outlet UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 A fourth fused 12-Volt power outlet is located on the left quarter trim panel in the cargo area.
Page 178: Electrical Outlet Use With Engine Off
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electrical Outlet Use With Engine Off CAUTION! Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
Page 179 The control switch for the outlet is located in the switch bank above the climate control. Power Inverter Switch Press and release the switch once to turn ON the power outlet. A status indicator in the switch will illuminate in approximately one second to indicate that power is available at the outlet.
Page 180: Cup And Bottle Holders
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUP AND BOTTLE HOLDERS CUPHOLDERS Armrest Cupholders Center Console Cupholders...
Page 181: Bottle Holders
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 BOTTLE HOLDERS Quarter Trim Panel Cupholders (Seven Passenger Models) Door Bottle Holder...
Page 182: Storage
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! If containers of hot liquid are placed in the bottle holder, they can spill when the door is closed, burn- ing the occupants. Be careful when closing the doors to avoid injury. STORAGE Beverage Cooler/Storage Compartment —...
Page 183 Press and release the button on the door to open it. The large door swings upward to allow easy access to the compartment’s contents. Beverage Cooler Operation The blower speed setting on the climate control sets the rate at which air flows into the compartment. The airflow control valve inside the compartment determines how much air flows into the compartment.
Page 184: Instrument Panel Storage Compartment - If Equipped
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Whether operating a Manual Heating and A/C system or operating an ATC system in a manual mode, the A/C indicator must be ON to cool the compartment. Instrument Panel Storage Compartment — If Equipped Press and release the button on the door to open it.
Page 185: Center Console Storage
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 Center Console Storage Center Console Cubby Bin Center Stack Cubby Bin...
Page 186: Flip 'N Stow™ Front Passenger Seat Storage - If Equipped
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Center Console Storage Bin NOTE: The sliding armrest (if so equipped) must be in the rearward position in order to access the release button on the front of the bin door. Flip ’n Stow™ Front Passenger Seat Storage — If Equipped The seat latch release-loop is located in the center of the seat cushion between the seat cushion and the seatback.
Page 187: Second-Row Passenger Seat Temporary Storage Bin
NOTE: Make sure that objects inside the bin do not interfere with the latch before closing the seat. Push the seat cushion downward after closing it to make sure it latches to the base. WARNING! Be certain that the seat cushion is locked securely into position before using the seat.
Page 188: Second-Row Map Pocket And Grocery Retainers - If Equipped
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Second-Row Map Pocket and Grocery Retainers — If Equipped A map storage pocket and grocery retainers are located on the back of the drivers seatback. 1 - Grocery Retainers 2 - Map Storage In-Floor Storage Bin with Removable Liner NOTE: Position the front seat to at least a mid-track position to provide easier access to the storage bin.
Page 189 In-Floor Storage Bin To access the bin, position the floor mat aside (if equipped). Pull the door latch release-loop upward to release the latch and then forward to open the bin door. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 The liner can be removed for easy cleaning by lifting on the notches as shown.
Page 190: Cargo Area Features
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CARGO AREA FEATURES Rechargeable Flashlight — If Equipped The rechargeable LED flashlight stores in its charging station in the left rear quarter trim panel. To remove it, press on the indent on the side of the flashlight and release.
Page 191 A retractable cargo area cover (if equipped). Seven Passenger System Features A large built-in storage bin with a hinged hardcover located in the floor behind the third-row passenger seats. 60/40 split second-row passenger seats with fold flat feature, which allows for extended cargo space. Refer to “Seats”...
Page 192 190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Cargo tie-downs are not safe anchors for a child seat tether strap. In a sudden stop or collision, a tie-down could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers.
Page 193 Retractable Cargo Area Cover (If Equipped) — Five Passenger Models NOTE: The purpose of this cover is for privacy, not to secure loads. It will not prevent cargo from shifting or protect passengers from loose cargo. The removable retractable cargo area cover mounts in the cargo area behind the top of the rear seats.
Page 194 192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Next, grab the cover handle and pull the cover toward you. As the cover nears the liftgate opening, guide the rear attachment posts (on both ends of the cover) into the notches in the trim panels. Then, lower the cover to position the posts into the bottom of the notches and release the handle.
Page 195: Rear Window Features
REAR WINDOW FEATURES Rear Window Wiper/Washer — If Equipped The Rear Window Wiper/Washer Control is lo- cated on the right side of the steering column. Rear Window Wiper/Washer Control UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 The rotary ring switch on the lever controls rear wiper and washer operation.
Page 196 194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Turn the rear wiper OFF when driving through an automatic car wash. Damage to the rear wiper may result if the rear wiper switch is left in the ON position. In cold weather, always turn OFF the rear wiper switch and allow the rear wiper to return to the park position before turning OFF the engine.
Page 197: Rear Window Defroster - If Equipped
Rear Window Defroster — If Equipped The Electric Rear Window Defroster control is located on the climate control. Press this button to turn on the rear window defroster and the heated outside rearview mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on.
Page 198: Roof Luggage Rack - If Equipped
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ROOF LUGGAGE RACK — IF EQUIPPED The roof rack cross rails and side rails are designed to carry cargo weight. The load must not exceed 150 lbs (68 kg), and it should be distributed uniformly over the cross rails.
Page 199 2. Relocate the cross rails, aligning the cross rail stan- chions (end pieces) with one of the vertical marks on the outboard surface of the side rail for proper positioning. There are four frontward marks for the front cross rail and four rearward marks for the rear cross rail.
Page 200 198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Cross rails should remain equally spaced or parallel at any luggage rack position for proper function. Noncompliance could result in damage to the roof rack, cargo, and vehicle. To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg).
Page 201: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....203 Instrument Cluster ..... . 204 Instrument Cluster Descriptions .
Page 202 200 UNDERSTANDING YOUR INSTRUMENT PANEL Sales Code REN — Multimedia System — If Equipped ......234 Operating Instructions —...
Page 203 Sales Code REU — Multimedia System — If Equipped ......266 Operating Instructions — Satellite Radio ..267 Operating Instructions —...
Page 204 202 UNDERSTANDING YOUR INSTRUMENT PANEL Remote Sound System Controls — If Equipped . . 282 Right-Hand Switch Functions ... . . 283 Left-Hand Switch Functions For Radio Operation ......283 Left-Hand Switch Functions For Media (i.e., CD) Operation .
Page 205: Instrument Panel Features
INSTRUMENT PANEL FEATURES 1 — Side Window Demist Outlet 2 — Air Outlet 3 — Instrument Cluster 4 — Storage Compartment or Remote Display Panel* UNDERSTANDING YOUR INSTRUMENT PANEL 203 5 — HAZARD Switch 6 — Switch Bank 7 — Beverage Cooler/Storage Compartment* 8 —...
Page 206: Instrument Cluster
204 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER...
Page 207: Instrument Cluster Descriptions
INSTRUMENT CLUSTER DESCRIPTIONS 1. Coolant Temperature Gauge The temperature gauge indicates engine coolant tem- perature. Any reading within the normal range indicates that the cooling system is operating satisfactorily. The gauge pointer will likely indicate a high temperature when driving in hot weather, up mountain grades, in heavy traffic, or when towing a trailer.
Page 208 206 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Coolant Temperature Warning Light This light warns of an overheated engine condi- tion. If the light turns on while driving, safely pull over and stop the vehicle. If the A/C system is on, turn it off. Also, shift the transaxle into NEUTRAL and idle the vehicle.
Page 209 WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, refer to Section 7 and follow the warnings under the Cooling System Pressure Cap paragraph.
Page 210 208 UNDERSTANDING YOUR INSTRUMENT PANEL 10. Vehicle Security Alarm (VSA) Indicator Light — If Equipped This light will flash rapidly for approximately 16 seconds when the vehicle Security system is arming and then flash slowly when the system is armed. The light will also turn on for about three seconds when the ignition switch is first turned ON.
Page 211 15. Odometer/Trip Odometer The odometer shows the total distance the vehicle has been driven. The trip odometer shows individual trip mileage. Refer to “Trip Odometer button” for additional information. NOTE: U.S. Federal regulations require upon transfer of vehicle ownership, the seller certify the mileage the vehicle has been driven.
Page 212 210 UNDERSTANDING YOUR INSTRUMENT PANEL off the message. If the problem persists, the message will appear the next time the vehicle is started. A loose, improperly installed, or damaged fuel filler cap may also turn on the MIL. (See page 421 for more information.) Change Oil Message (Base And Mid Line Clusters Only)
Page 213 16. Electronic Throttle Control (ETC) Warning Light — If Equipped This light will turn on briefly as a bulb check when the ignition switch is turned ON. This light will also turn on while the engine is running if there is a problem with the Elec- tronic Throttle Control (ETC) system.
Page 214 212 UNDERSTANDING YOUR INSTRUMENT PANEL 18. Charging System Warning Light This light shows the status of the electrical charg- ing system. The light should turn on when the ignition switch is first turned ON and remain on briefly as a bulb check. If the light stays on or turns on while driving, turn off some of the vehicle’s electrical devices, such as the fog lights or rear defroster.
Page 215 21. Tire Pressure Monitoring Telltale Light — If Equipped Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those...
Page 216 214 UNDERSTANDING YOUR INSTRUMENT PANEL When the malfunction indicator is illuminated, the sys- tem may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly.
Page 217 22. Anti-Lock Brake System (ABS) Warning Light This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If the ABS light remains on or turns on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required.
Page 218 216 UNDERSTANDING YOUR INSTRUMENT PANEL stays on through several of your typical driving cycles. In most situations, the vehicle will drive normally and will not require towing. If the MIL flashes when the engine is running, serious conditions may exist that could lead to immediate loss of power or severe catalytic converter damage.
Page 219 26. Brake System Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the light turns on, it may indi- cate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the ABS.
Page 220 218 UNDERSTANDING YOUR INSTRUMENT PANEL The operation of the Brake Warning Light can be checked by turning the ignition switch from the LOCK position to the ON position. The light should turn on for approxi- mately two seconds and then turn off. The light will remain on if the parking brake is applied or if a brake fault is detected.
Page 221 this display. Press and release the button once to turn on the display. Press and release it again to turn off the display. Setting Compass Variance (Mid Line Cluster Only) Compass Variance is the difference between magnetic North and geographic North. To allow the compass module to compensate for that difference and ensure accuracy, you can set the variance in the compass module to the zone where the vehicle is located according to the...
Page 222 220 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The default variance setting is Zone 8. When setting the variance, the numbering will wrap around from Zone 15 to Zone 1. Calibrating the Compass (Mid Line Cluster Only) If the compass appears erratic, inaccurate, or abnormal, you may wish to calibrate it.
Page 223: Electronic Vehicle Information Center (Evic) - If Equipped
seconds). Finally, drive the vehicle in one or more com- plete circles, at speeds under 5 mph (8 km/h), in an area free from power lines and large metallic objects, until the “CAL” indicator turns off. The compass will now func- tion normally.
Page 224 222 UNDERSTANDING YOUR INSTRUMENT PANEL System status, including vehicle information warning message displays, and Tire Pressure Monitor System (TPMS) displays (if equipped), and, Personal Settings (customer programmable features). The system allows the driver to select information by pressing the following buttons mounted on the steering wheel.
Page 225: Electronic Vehicle Information Center (Evic) Displays
Press this button to reset Trip Functions and change Personal Settings. RESET Button Press this button to scroll through Trip Func- tions (Average Fuel Economy, Distance To Empty [DTE], Elapsed Time, Units In), System Status Messages, and Personal Settings (Cus- SCROLL tomer Programmable Features).
Page 226 224 UNDERSTANDING YOUR INSTRUMENT PANEL Channel # Transmit. Refer to “Garage Door Opener” in Section 2. Channel # Training. Refer to “Garage Door Opener” in Section 2. Channel # Trained. Refer to “Garage Door Opener” in Section 2. Clearing Channels. Refer to “Garage Door Opener” in Section 2.
Page 227: Oil Change Required
Coolant Low Key in Ignition Lights On Oil Change Required Your vehicle is equipped with an engine oil change indicator system. The “Oil Change Required” message will display in the EVIC for approximately 5 seconds after a single chime has sounded to indicate the next scheduled oil change interval.
Page 228: Trip Functions
226 UNDERSTANDING YOUR INSTRUMENT PANEL Trip Functions Press and release the MENU button until one of the following Trip Functions displays in the EVIC: Average Fuel Economy Distance To Empty Elapsed Time Units In Press the SCROLL button to cycle through all the Trip Computer functions.
Page 229: Compass Display
a significant amount of fuel to the vehicle will turn off the LOW FUEL text and a new DTE value will display. Elapsed Time Shows the total elapsed time of travel since the last reset when the ignition switch is in the ACC position. Elapsed time will increment when the ignition switch is in the ON or START position.
Page 230 228 UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Compass Calibration This compass is self-calibrating, which eliminates the need to calibrate the compass manually. When the ve- hicle is new, the compass may appear erratic and the EVIC will display “CAL” until the compass is calibrated. You may calibrate the compass by slowly completing one or more 360-degree turns (in an area free from large metal or metallic objects) until the “CAL”...
Page 231 Compass Variance Compass Variance is the difference between magnetic North and geographic North. To allow the compass module to compensate for that difference and ensure accuracy, you can set the variance in the compass module to the zone where the vehicle is located according to the Compass Variance Map.
Page 232: Personal Settings (Customer Programmable Features)
230 UNDERSTANDING YOUR INSTRUMENT PANEL 1. Turn the ignition switch ON. 2. Press and release the MENU button until Personal Settings displays in the EVIC. 3. Press the SCROLL button until “COMPASS VARI- ANCE” message and the last variance zone number displays in the EVIC.
Page 233 “RKE UNLOCK” When Driver Door 1st Press is selected, only the driver’s door will unlock on the first press of the Remote Keyless Entry (RKE) UNLOCK button. When Driver Door 1st Press is selected, you must press the RKE UNLOCK button twice to unlock the passenger doors and liftgate.
Page 234 232 UNDERSTANDING YOUR INSTRUMENT PANEL ON. The headlights will also turn off when the wipers are turned OFF if they were turned ON by this feature. To make your selection, press and release the RESET button until “ON” or “OFF” appears. “KEY-OFF POWER DELAY”...
Page 235: Radio General Information
CALIBRATE COMPASS Refer to “Manual Compass Calibration” under “Com- pass Display.” RADIO GENERAL INFORMATION Radio Broadcast Signals The radio will provide excellent reception under most operating conditions. Like any system, however, car radios have performance limitations, due to mobile op- eration and natural phenomena, which might lead you to believe your sound system is malfunctioning.
Page 236: Fm Reception
234 UNDERSTANDING YOUR INSTRUMENT PANEL FM Reception Because FM transmission is based on frequency varia- tions, interference that consists of amplitude variations can be filtered out, leaving the reception relatively clear, which is the major feature of FM radio. NOTE: For vehicles not equipped with the Electronic Vehicle Information Center (EVIC), the radio and steering wheel radio controls (if equipped) will remain active...
Page 237: Operating Instructions - Satellite Radio (If Equipped)
An auxiliary input jack permits passengers to listen to a portable MP3 player through the vehicle’s speakers. For vehicles equipped with the Video Entertainment System (VES)™, separate audio outputs allow passengers to listen to the vehicle speakers while different audio tracks play through the system’s wireless headphones.
Page 238: Clock Setting Procedure
236 UNDERSTANDING YOUR INSTRUMENT PANEL Clock Setting Procedure Setting the Clock 1. Turn on the multimedia system. 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. To move the hour forward, touch the screen where the word “Hour”...
Page 239 Show Time if Radio is Off When selected, this feature will display the time of day on the touch screen when the multimedia system is turned off. Proceed as follows to change the current setting: 1. Turn on the multimedia system. 2.
Page 240: Sales Code Req - Am/Fm Stereo Radio And 6-Disc Cd/Dvd Changer (Mp3/Wma Aux Jack)
238 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE REQ — AM/FM STEREO RADIO AND 6–DISC CD/DVD CHANGER (MP3/WMA AUX JACK) NOTE: The radio sales code is located on the lower right side of your radio faceplate. RET Radio Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
Page 241 SEEK Buttons Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection.
Page 242 240 UNDERSTANDING YOUR INSTRUMENT PANEL Clock Setting Procedure 1. Press and hold the TIME button until the hours blink. 2. Adjust the hours by turning the right side TUNE/ SCROLL control knob. 3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes.
Page 243 Setting the Tone, Balance, and Fade Push the rotary TUNE/SCROLL control knob and BASS will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the bass tones. Push the rotary TUNE/SCROLL control knob a second time and MID will display.
Page 244 242 UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the MUSIC TYPE button to select the following format types: Program Type No program type or un- defined Adult Hits Classical Classic Rock College Country Foreign Language Information Jazz News Nostalgia Oldies 16-Digit Character Display Rhythm and Blues None...
Page 245 By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name. The Music Type function only operates when in the FM mode. If a preset button is activated while in the Music Type (Program Type) mode, the Music Type mode will be exited and the radio will tune to the preset station.
Page 246 244 UNDERSTANDING YOUR INSTRUMENT PANEL Angle – Repeatedly pressing SELECT will change the viewing angle if supported by the DVD disc (if equipped). NOTE: The available selections for each of the above entries varies depending upon the disc. NOTE: These selections can only be made while playing a DVD.
Page 247 Audio Language — If Equipped Selecting this item allows you to choose a default audio language (effective only if the language is supported by the disc). You can select a language not listed by scrolling down and selecting other. Enter the country code using the TUNE/SCROLL control knob to scroll up and down to select the number and then push to select.
Page 248 246 UNDERSTANDING YOUR INSTRUMENT PANEL a disc is loaded, changes will not be effective. Also, the defaults are effective only if the disc supports the customer-preferred settings. AM and FM Buttons Press the buttons to select AM or FM Modes. SET Button —...
Page 249: Operation Instructions - (Disc Mode For Cd And Mp3/Wma Audio Play, Dvd-Video)
Operation Instructions - (DISC MODE for CD and MP3/WMA Audio Play, DVD-VIDEO) The radio DVD player and many DVD discs are coded by geographic region. These region codes must match in order for the disc to play. If the region code for the DVD disc does not match the region code for the radio DVD player, it will not play the disc.
Page 250 248 UNDERSTANDING YOUR INSTRUMENT PANEL Eject Button — Ejecting Compact Disc(s) Press the EJECT button and the pushbutton with the corresponding number (1-6) where the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show EJECTING DISC when the disc is being ejected and prompt the user to remove the disc.
Page 251: Notes On Playing Mp3/Wma Files
Notes On Playing MP3/WMA Files The radio can play MP3/WMA files; however, acceptable MP3/WMA file recording media and formats are limited. When writing MP3/WMA files, pay attention to the following restrictions. Supported Media (Disc Types) The MP3/WMA file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3,WMA, DVD Video, DVD-R, DVD-RW, DVD+R, DVD+RW, and CDDA+MP3.
Page 252 250 UNDERSTANDING YOUR INSTRUMENT PANEL If a disc contains multi-formats, such as CD audio and MP3/WMA tracks, the radio will only play the MP3/ WMA tracks on that disc. Supported MP3/WMA File Formats The radio will recognize only files with the MP3/WMA extension as MP3/WMA files.
Page 253: List Button (Disc Mode For Mp3/Wma Play)
Playback of MP3/WMA Files When a medium containing MP3/WMA data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3/WMA files. Loading times for playback of MP3/WMA files may be affected by the following: Media - CD-RW media may take longer to load than...
Page 254 252 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the INFO button again for three seconds to return to elapsed time display. Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device such as an MP3/WMA player, cassette player, or microphone and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers.
Page 255 Operating Instructions — Voice Recognition System (VR) (If Equipped) For the radio, refer to “Voice Recognition System (VR)” in Section 3. For UConnect “Voice Recognition System (VR),” refer to “Hands-Free Communication (UConnect )” in Section 3. Operating Instructions - Hands-Free Phone (UConnect ) (If Equipped) Refer to “Hands-Free Communication (UConnect )”...
Page 256: Sales Code Res - Am/Fm Stereo Radio With Cd Player (Mp3 Aux Jack)
254 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RES — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of your radio faceplate. RES Radio (Non-Satellite Model Shown - With Satellite Similar) Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC...
Page 257 to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. SCAN Button Pressing the SCAN button causes the tuner to search for the next listenable station in AM or FM frequencies, pausing for five seconds at each listenable station before continuing to the next.
Page 258 256 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Adjust the hours by turning the right side Tune/Scroll control knob. 3. After adjusting the hours, press the right side Tune/ Scroll control knob to set the minutes. The minutes will begin to blink. 4.
Page 259 Push the rotary Tune/Scroll control knob a second time and MID will display. Turn the Tune/Scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary Tune/Scroll control knob a third time and TREBLE will display.
Page 260 258 UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Foreign Language Information Jazz News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues 16-Digit Character Display Language Inform Jazz News Nostalga By pressing the SEEK button when the Music Type icon Oldies is displayed, the radio will be tuned to the next frequency Persnlty...
Page 261 Set Clock — Pressing the SELECT button will allow you to set the clock. Turn the Tune/Scroll control knob to adjust the hours and then press and turn the Tune/Scroll control knob to adjust the minutes. Press the Tune/Scroll control knob again to save changes. AM and FM Buttons Press the buttons to select AM or FM modes.
Page 262: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
260 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - CD MODE for CD and MP3 Audio Play NOTE: The ignition switch must be in the ON or ACC position to operate the radio. NOTE: This radio is capable of playing compact discs (CD), recordable compact discs (CD-R), rewritable com- pact discs (CD-RW), compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks.
Page 263 EJECT Button - Ejecting a CD Press the EJECT button to eject the CD. If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the CD is not removed, the radio will reinsert the CD but will not play it. A disc can be ejected with the radio and ignition OFF.
Page 264: Notes On Playing Mp3 Files
262 UNDERSTANDING YOUR INSTRUMENT PANEL AM or FM Button Switches the AM or FM radio to the opposite radio mode. RND Button (Random Play Button) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace.
Page 265 a number instead. With a maximum number of files, exceeding 20 folders will result in this display. With 200 files, exceeding 50 folders will result in this display.) Maximum number of characters in file/folder names: Level 1: 12 (including a separator . and a three- character extension) Level 2: 31 (including a separator .
Page 266 264 UNDERSTANDING YOUR INSTRUMENT PANEL MPEG Sampling Specification Frequency (kHz) MPEG-1 Audio 48, 44.1, 32 Layer 3 MPEG-2 Audio 24, 22.05, 16 Layer 3 ID3 Tag information for artist, song title, and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios.
Page 267: List Button (Cd Mode For Mp3 Play)
LIST Button (CD Mode for MP3 Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the Tune/Scroll control knob. Selecting a folder by pressing the Tune/Scroll control knob will begin playing the files contained in that folder (or the next folder in sequence if the selection does not contain playable files).
Page 268: Sales Code Reu - Multimedia System - If Equipped
266 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (Auxiliary Mode) Press this button to change the display to time of day. The time of day will display for five seconds (when ignition is OFF). Operating Instructions - Hands-Free Phone (UConnect ) (If Equipped) Refer to “Hands-Free Communication (UConnect )”...
Page 269: Operating Instructions - Satellite Radio
a remote color screen to provide maps, turn identifica- tion, selection menus, and instructions for selecting a variety of destinations and routes. A shared HDD for the navigation system, the database, and other radio features allows uploads of music and photos from CDs or through the USB port.
Page 270 268 UNDERSTANDING YOUR INSTRUMENT PANEL Changing the Time Zone NOTE: You can skip Steps 2 and 3 by pressing and holding the “TIME” button on the radio for three sec- onds. 1. Turn on the multimedia system. 2. Press and release the “SETUP” button on the radio. 3.
Page 271 3. If “Time Setup” is highlighted on the menu, press and release the joystick in the center of the radio. Otherwise, turn the knob surrounding the joystick to select “Time Setup,” and then press and release the joystick. 4. Turn the knob surrounding the joystick to scroll to “Daylight Savings,”...
Page 272 270 UNDERSTANDING YOUR INSTRUMENT PANEL 4. If “User Time” has a check mark next to it, proceed to the next step. Otherwise, turn the knob surrounding the joystick to scroll to “User Time,” and then press and release the joystick. 5.
Page 273: Satellite Radio - If Equipped (Ren/Req/Rer/Res/Reu Radios Only)
4. Turn the knob surrounding the joystick to scroll to “Clock if Radio off,” and then press and release the joystick to change the current setting. A check mark will display next to “Clock if Radio off” when the feature is selected.
Page 274: Selecting Satellite Mode
272 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Your Vehicle Identification Number. To access the ESN/SID, refer to the following steps: ESN/SID Access With REQ/RES Radios With the ignition switch in the ON/RUN or ACC posi- tion and the radio on, press the SETUP button and scroll using the Tune/Scroll control knob until Sirius ID is selected.
Page 275: Reception Quality
as possible, within the loading design of the rack. Do not place items directly on or above the antenna. Reception Quality Satellite reception may be interrupted due to one of the following reasons: The vehicle is parked in an underground parking structure or under a physical obstacle.
Page 276 274 UNDERSTANDING YOUR INSTRUMENT PANEL INFO Button — Except REU Radio Pressing the INFO button will cycle the display informa- tion between Artist, Song Title, and Composer (if avail- able). Also, pressing and holding the INFO button for an additional three seconds will make the radio display the Song Title all of the time (press and hold again to return to normal display).
Page 277 made, you can seek up, or down, or scan the channels and the radio will tune to the next station matching the selected format. There is no time-out for this screen. Pressing the MUSIC TYPE button again will close the MUSIC TYPE screen.
Page 278: Operating Instructions - Hands-Free Phone (If Equipped)
276 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Hands-Free Phone (If Equipped) Refer to “Hands-Free Communication (UConnect )” in Section 3. Operating Instructions - Video Entertainment System (VES)™ (If Equipped) Refer to separate “Video Entertainment System (VES)™ Guide.” SIRIUS BACKSEAT TV™ — IF EQUIPPED Satellite video uses direct satellite receiver broadcasting technology to provide streaming video.
Page 279 VES™ with Rear HVAC Controls The touch screen radio and DVD player controls allow front seat operation for easy setup in the case of younger rear seat passengers. A battery-powered infrared remote control that snaps into a molded compartment in the center console. UNDERSTANDING YOUR INSTRUMENT PANEL 277 Two wireless infrared headsets allow rear seat passen- gers to listen to the same or individual audio sources.
Page 280: Universal Consumer Interface (Uci) - If Equipped
278 UNDERSTANDING YOUR INSTRUMENT PANEL UNIVERSAL CONSUMER INTERFACE (UCI) — IF EQUIPPED NOTE: This section is for sales code RES/REL and REQ/RET radios only with UConnect . For sales code REN/REZ touch screen radio and REU/REX/RE1 radio, refer to the separate User’s Manual. This feature allows you to plug an iPod mobile digital device into the vehicle’s sound system through a connec- tor (UCI connector) using an optional connection cable...
Page 281: Play Mode
Play Mode When switched to UCI mode the iPod will be in Play mode. In Play mode, you may use the following buttons on the radio faceplate to control the iPod and display data: Tune/Scroll Knob Use the Tune/Scroll knob to go to the next or previous track.
Page 282: List Or Browse Mode
280 UNDERSTANDING YOUR INSTRUMENT PANEL previous track in the list; if you press this button at any other time in the current track it will go back to the beginning of the track. If the right (up) button is pressed during Play mode, it will go to the next track in the list.
Page 283 Tune/Scroll Knob In the List mode, the Tune/Scroll knob functions in a similar manner as the scroll wheel on the iPod . Turning the Tune/Scroll knob clockwise (forward) and counterclockwise (backward) scrolls through lists, dis- playing the track detail on the radio display. Once you have the track to be played highlighted on the radio display, press the Tune/Scroll knob to select and start playing the track.
Page 284: Remote Sound System Controls - If Equipped
282 UNDERSTANDING YOUR INSTRUMENT PANEL LIST Button Pressing the LIST button will take to the top level menu of the iPod . This takes you to the same top level menu as on your iPod . Turn the Tune/Scroll knob to list the top menu item you wish to select and then press the Tune/Scroll knob.
Page 285: Right-Hand Switch Functions
Remote Sound Controls Right-Hand Switch Functions Press the top of the switch to increase the volume. Press the bottom of the switch to decrease the volume. Press the button in the center of the switch to change modes (i.e., AM, FM, etc.). UNDERSTANDING YOUR INSTRUMENT PANEL 283 Left-Hand Switch Functions for Radio Operation Press the top of the switch to SEEK the next listenable...
Page 286: Cd/Dvd Maintenance
284 UNDERSTANDING YOUR INSTRUMENT PANEL Press the switch up or down twice to listen to the second track, three times to listen to the third track, and so forth. Press the button located in the center of the switch to change to the next preset that you have programmed.
Page 287: Climate Controls
CLIMATE CONTROLS The air conditioning and heating system is designed to make you comfortable in all types of weather. For infor- mation about basic climate control functions, refer to “General Climate Control Functions — All Systems.” For more detailed information about the climate controls in your vehicle, refer to “Single-Zone Manual Air Condi- tioning and Heating System,”...
Page 288 286 UNDERSTANDING YOUR INSTRUMENT PANEL Panel Air is directed through the outlets in the instrument panel. For vehicles equipped with a three-zone sys- tem, air is also directed through the outlets in the headliner, unless the climate control for the rear passen- gers is ON and in Floor mode.
Page 289 NOTE: This setting works best in cold or snowy condi- tions that require extra heat to the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield. Defrost Air is directed through the windshield and side window demist outlets.
Page 290: Single-Zone Manual Air Conditioning And Heating System
288 UNDERSTANDING YOUR INSTRUMENT PANEL Single-Zone Manual Air Conditioning and Heating System Single-Zone Manual Climate Control 1. Blower Control The blower speed increases as you move the control to the right from the “O” (Off) position. There are four blower speeds. 2.
Page 291: Two- And Three-Zone Manual Air Conditioning And Heating Systems - If Equipped
6. Recirculation Mode Control Press and release to change the current setting. The indicator illuminates when ON. Note - The A/C compressor operates in Mix and Defrost, or a blend of these modes, even if the A/C control is not pressed. This dehumidifies the air to help dry the windshield.
Page 292 290 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Panel Mode Button Press and release to select. The indicator illuminates when selected. 3. Bi-Level Mode Button Press and release to select. The indicator illuminates when selected. 4. Front Blower Control The blower speed increases as you move the control to the right from the “O”...
Page 293 11. A/C Button Press and release to change the current setting. The indicator illuminates when ON. Rear-Zone Manual Climate Control UNDERSTANDING YOUR INSTRUMENT PANEL 291 1. RR Control Turns the climate control in the overhead console above the second row passenger seats ON and OFF. Press and release to change the current setting.
Page 294 292 UNDERSTANDING YOUR INSTRUMENT PANEL Rear-Zone Manual Climate Control The Rear-Zone Manual Climate Control for the rear passengers is located in the overhead console above the second row passenger seats. 1. Rear Blower Control The blower speed increases as you move the control to the right from the “O”...
Page 295: Two- And Three-Zone Automatic Temperature Control (Atc) Systems - If Equipped
Two- and Three-Zone Automatic Temperature Control (ATC) Systems — If Equipped Two-Zone ATC 1. ATC ON/OFF Button Press and release to change the current setting. UNDERSTANDING YOUR INSTRUMENT PANEL 293 2. Left Front Temperature Control Provides left front seat occupant with independent tem- perature control.
Page 296 294 UNDERSTANDING YOUR INSTRUMENT PANEL 7. Mode Button Press the DOWN or UP arrow to change the mode of air distribution to Floor, Panel, Bi-Level, or Mix. 8. Electric Rear Window Defroster Button Refer to “Rear Window Features” in Section 3 for more information.
Page 297 2. Left Front Temperature Control Provides left front seat occupant with independent tem- perature control. Turn left for cooler or right for warmer temperature settings. 3. Display Screen Shows the current blower speed, mode, and temperature settings, and it will display an indicator when the A/C is 4.
Page 298 296 UNDERSTANDING YOUR INSTRUMENT PANEL Note - To prevent window fogging, Recirculation Mode will not operate when either Defrost or Mix mode is selected. Doing so will cause the indicator to blink and then turn OFF. Three-Zone ATC Lower Control Panel 1.
Page 299 5. Electric Rear Window Defroster Button Refer to “Rear Window Features” in Section 3 for more information. Rear-Zone ATC The Rear-Zone ATC for the rear passengers is in the overhead console above the second row passenger seats. UNDERSTANDING YOUR INSTRUMENT PANEL 297 1.
Page 300 298 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Rear Mode Control Turn to select Panel, Bi-Level, or Floor for the mode of rear cabin air distribution. Automatic Operation — Two- and Three-Zone ATC The Two- and Three-Zone ATC systems automatically maintain the climate in the cabin of the vehicle. To accomplish this, the system gathers information from the climate controls, from a dual sun-sensor located in the top of the instrument panel, from an infrared sensor...
Page 301 maintain for each zone. On Three-Zone ATC systems, if so desired, push and release the SYNC button. Then turn the Left Front Temperature Control to dial in the tem- perature that you want the system to maintain for all three zones. Once the comfort level is selected, the system will main- tain that level automatically using the heating system.
Page 302: Operating Tips
300 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips NOTE: Refer to the chart at the end of this section for suggested control settings for various weather condi- tions. Summer Operation The engine cooling system in air-conditioned vehicles must be protected with a high-quality antifreeze coolant to provide proper corrosion protection and to protect against engine overheating.
Page 303 Side Window Demisters A side window demister outlet is located at each end of the instrument panel. These non-adjustable outlets direct air toward the side windows when the system is in the Floor, Mix, or Defrost mode. The air is directed at the area of the windows through which you view the outside mirrors.
Page 304 302 UNDERSTANDING YOUR INSTRUMENT PANEL Control Setting Suggestions for Various Weather Conditions...
Page 305: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ..... 307 Automatic Transaxle ....308 Normal Starting (Tip Start) .
Page 306 304 STARTING AND OPERATING Driving On Slippery Surfaces ....320 Acceleration ......320 Traction .
Page 307 Tire Pressure Monitor System (TPMS) — If Equipped ......355 Base System — If Equipped ....358 Premium System —...
Page 308 306 STARTING AND OPERATING Loose Fuel Filler Cap Message ... . 374 Vehicle Loading ......375 Vehicle Certification Label .
Page 309: Starting Procedures
STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. STARTING AND OPERATING 307 WARNING! Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons.
Page 310: Automatic Transaxle
308 STARTING AND OPERATING Automatic Transaxle The shift lever must be in the NEUTRAL or PARK position before you can start the engine. Apply the brakes before shifting into any driving gear. CAUTION! Damage to the transaxle may occur if the following precautions are not observed: Shift into PARK only after the vehicle has come to a complete stop.
Page 311: Normal Starting (Tip Start)
Normal Starting (Tip Start) NOTE: Normal Starting of either a cold or a warm engine is obtained without pumping or depressing the accelerator pedal. Do not press the accelerator. Use the Fob with Integrated Key to briefly turn the ignition switch to the START position and release it as soon as the starter engages.
Page 312: If Engine Fails To Start
310 STARTING AND OPERATING If Engine Fails To Start WARNING! Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. Do not attempt to push or tow your vehicle to get it started.
Page 313: After Starting
After Starting The idle speed is controlled automatically and it will decrease as the engine warms up. ENGINE BLOCK HEATER — IF EQUIPPED The engine block heater warms engine coolant and permits quicker starts in cold weather. Connect the cord to a standard 110-115 Volt AC electrical outlet with a grounded, three-wire extension cord.
Page 314: Brake/Transaxle Interlock System
312 STARTING AND OPERATING NOTE: You MUST press and hold the brake pedal down while shifting out of PARK. WARNING! It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse.
Page 315: Automatic Transaxle Ignition Interlock System
4. Insert a screwdriver or similar small tool into the hole at the front of the cubby bin and push the manual override release lever forward. 5. While holding the release lever forward, move the shift lever from PARK to NEUTRAL. 6.
Page 316 314 STARTING AND OPERATING Gear Ranges PARK PARK supplements the parking brake by locking the transaxle. The engine can be started in this range. Never attempt to use PARK while vehicle is in motion. Apply parking brake when leaving vehicle in this range. When parking on a flat surface, place the shift lever in the PARK position first, and then apply the parking brake.
Page 317 NEUTRAL The engine may be started in this range. WARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have an accident.
Page 318 316 STARTING AND OPERATING “3” (Drive) — 4-Speed Transaxle This range eliminates shifts into “D” (Overdrive). The transaxle will operate normally in 1st, 2nd, and 3rd while in this range. The “3” (Drive) range should also be used when descending steep grades to prevent brake system distress.
Page 319: Autostick - If Equipped
PARK, REVERSE, and NEUTRAL will continue to oper- ate. This Reset feature allows the vehicle to be driven to an authorized dealer for service without damaging the transaxle. In the event of a momentary problem, the transaxle can be reset to regain all forward gears by performing the following steps: 1.
Page 320: Autostick Operation
318 STARTING AND OPERATING AutoStick Operation By placing the shift lever one shift-level below the DRIVE position, it can be moved from side to side. This allows the driver to select a higher or lower range of gears. Moving the shift lever to the Left (-) triggers a downshift and to the Right (+) an upshift.
Page 321: All Wheel Drive (Awd) - If Equipped
If a low range is selected and the engine accelerates to the rev limit, the transaxle will automatically select the next higher ratio. If a downshift would cause the engine to over-speed, that shift will not occur until it is safe for the engine. Mostly the transaxle will stay in the manually selected ratio, however: −...
Page 322: Driving On Slippery Surfaces
320 STARTING AND OPERATING CAUTION! All wheels must have the same size and type tires. Unequal tire sizes must not be used. Unequal tire size may cause failure of the power transfer unit. DRIVING ON SLIPPERY SURFACES ACCELERATION Rapid acceleration on snow covered, wet, or other slip- pery surfaces may cause the front wheels to pull errati- cally to the right or left.
Page 323: Driving Through Water
2. Slow down if the road has standing water or puddles. 3. Replace the tires when tread wear indicators first become visible. 4. Keep the tires properly inflated. 5. Maintain enough distance between your vehicle and the vehicle in front of you to avoid a collision in a sudden stop.
Page 324 322 STARTING AND OPERATING CAUTION! Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle. Determine the condition of the road or the path that is under water, and if there are any obstacles in the way, before driving through the standing water.
Page 325: Parking Brake
WARNING! Driving through standing water limits your vehi- cle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. Driving through standing water limits your vehi- cle’s braking capabilities, which increases stop- ping distances. Therefore, after driving through standing water, drive slowly and lightly press on the brake pedal several times to dry the brakes.
Page 326 324 STARTING AND OPERATING As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. The foot operated parking brake is positioned below the lower left corner of the instrument panel. To apply the parking brake, push the parking brake pedal down and then remove your foot from the pedal.
Page 327 NOTE: This light only shows that the parking brake is applied. It does not show the degree of brake application. The Brake System Warning Light in the instru- ment cluster will turn on when the parking brake is applied and the ignition switch is on. NOTE: This light only shows that the parking brake is applied.
Page 328: Brake System
326 STARTING AND OPERATING BRAKE SYSTEM Your vehicle is equipped with dual hydraulic brake systems. If either of the two hydraulic systems loses normal capability, the remaining system will still function. However, there will be some loss of overall braking effectiveness. This will be evident by increased pedal travel during application and greater pedal force required to slow or stop the vehicle.
Page 329: Anti-Lock Brake System (Abs)
Anti-Lock Brake System (ABS) This system aids the driver in maintaining vehicle control under adverse braking conditions. The system controls hydraulic brake pressure to prevent wheel lock-up to help avoid skidding on slippery surfaces during braking. Refer to “Anti-Lock Brake System (ABS)” under “Elec- tronic Brake Control System”...
Page 330: Electronic Brake Control System
328 STARTING AND OPERATING ELECTRONIC BRAKE CONTROL SYSTEM Your vehicle is equipped with an advanced electronic brake control system commonly referred to as ESP. This system includes Anti-Lock Brake System (ABS), Brake Assist System (BAS), Traction Control System (TCS), Elec- tronic Roll Mitigation (ERM), and Electronic Stability Pro- gram (ESP).
Page 331 WARNING! The ABS contains sophisticated electronic equipment that may be susceptible to interference caused by im- properly installed or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability. Installation of such equip- ment should be performed by qualified professionals. Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident.
Page 332: Brake Assist System (Bas)
330 STARTING AND OPERATING If both the Brake System Warning Light and the ABS Light remain on, the ABS and Electronic Brake Force Distribution (EBD) systems are not functioning. Immedi- ate repair to the ABS system is required. Brake Assist System (BAS) The BAS is designed to optimize the vehicle’s braking capability during emergency braking maneuvers.
Page 333: Traction Control System (Tcs)
Traction Control System (TCS) This system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration and stability.
Page 334: Electronic Stability Program (Esp)
332 STARTING AND OPERATING WARNING! Many factors, such as vehicle loading, road condi- tions, and driving conditions, influence the chance that wheel lift or rollover may occur. ERM cannot prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or other vehicles.
Page 335 active. The ESP/TCS Indicator Light also flashes when TCS is active. If the ESP/TCS Indicator Light begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions. WARNING! ESP cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction...
Page 336: Esp/Bas Warning Light And Esp/Tcs Indicator Light
334 STARTING AND OPERATING ESP OFF Button NOTE: To improve the vehicle’s traction when driving with snow chains, or when starting off in deep snow, sand, or gravel, it may be desirable to switch to the “Partial Off” mode by momentarily depressing the ESP OFF button.
Page 337: Trailer Sway Control (Tsc)
NOTE: The ESP/TCS Indicator Light and the ESP/BAS Mal- function Indicator Light will turn on momentarily each time the ignition switch is turned ON. Each time the ignition is turned ON, the ESP System will be ON even if it was turned off previously. The ESP Control System will make buzzing or clicking sounds when it is active.
Page 338: Power Steering
336 STARTING AND OPERATING POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible to steer your vehicle.
Page 339: Tire Safety Information
TIRE SAFETY INFORMATION TIRE MARKINGS NOTE: P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. STARTING AND OPERATING 337 European-Metric tire sizing is based on European design standards.
Page 340 338 STARTING AND OPERATING Tire Sizing Chart Size Designation: P = Passenger Car tire size based on U.S. design standards ...blank... = Passenger Car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm)
Page 341 Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
Page 342 340 STARTING AND OPERATING TIRE IDENTIFICATION NUMBER (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.
Page 343: Tire Loading And Tire Pressure
TIRE LOADING AND TIRE PRESSURE Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side B-Pillar. Tire Placard Location STARTING AND OPERATING 341 Tire and Loading Information Placard Tire And Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle...
Page 344 342 STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading Information placard and in the “Vehicle Loading”...
Page 345 available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 = 750, and 1400 – 750 = 650 lbs [295 kg]). 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.
Page 346 344 STARTING AND OPERATING...
Page 347: Tires - General Information
WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 348 346 STARTING AND OPERATING WARNING! Unequal tire pressures can cause steering problems. You could lose control of your vehicle. Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left.
Page 349 Tire Placard Location The pressure should be checked and adjusted as well as inspecting for signs of tire wear or visible damage at least once a month. Use a good quality pocket-type gauge to check tire pressure. DO NOT make a visual judgement when determining proper inflation.
Page 350 348 STARTING AND OPERATING Tire pressures change by approximately 1 psi (7 kPa) per 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the Winter. Example: If garage temperature = 68°F (20°C) and the outside temperature = 32°F (0°C) then the cold tire inflation pressure should be increased by 3 psi (21 kPa), which equals 1 psi (7 kPa) for every 12°F (7°C) for this...
Page 351 Radial Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Al- ways use radial ply tires in sets of four (or six, in case of trucks with dual rear wheels).
Page 352 350 STARTING AND OPERATING DO NOT install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. DO NOT install more than one compact spare tire/wheel on the vehicle at any given time.
Page 353 Tire Spinning When stuck in mud, sand, snow, or ice conditions, DO NOT spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously with- out stopping when you are stuck. For additional information, refer to “Freeing A Stuck Vehicle”...
Page 354 352 STARTING AND OPERATING These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Many states have laws requiring tire replacement at this point.
Page 355 “Tread Wear Indicators”). Refer to the “Tire and Loading Information” placard for the size designation of your tire. The service description and load identification will be found on the original equipment tire. Failure to use equivalent replacement tires may adversely affect the safety, handling, and ride of your vehicle.
Page 356 354 STARTING AND OPERATING WARNING! NEVER use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle. Using a tire with a smaller load index could result in tire overloading and failure. You could lose control and have an accident.
Page 357: Tire Chains
TIRE CHAINS Due to limited clearance, tire chains are not recommended. CAUTION! Damage to the vehicle may result if tire chains are used. SNOW TIRES Some areas of the country require the use of snow tires during the winter. Standard tires are of the all season type and satisfy this requirement as indicated by the M+S designation on the tire sidewall.
Page 358 356 STARTING AND OPERATING how to properly inflate the vehicle’s tires. The tire pressure will also increase as the vehicle is driven. This is normal and there should be no adjustment for this increased pressure. The TPMS will warn the driver of a low tire pressure if the tire pressure falls below the low-pressure warn- ing limit for any reason, including low temperature effects and natural pressure loss through the tire.
Page 359 CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when us- ing replacement equipment that is not of the same size, type, and/or style.
Page 360: Base System - If Equipped
358 STARTING AND OPERATING Seasonal temperature changes will affect tire pressure, and the TPMS will monitor the actual tire pressure in the tire. Base System — If Equipped The Tire Pressure Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels.
Page 361 will repeat, providing the system fault still exists. The Tire Pressure Monitoring Telltale light will turn off when the fault condition no longer exists. A system fault can occur due to any of the following: 1. Jamming due to electronic devices or driving next to facilities emitting the same Radio Frequencies as the TPMS sensors.
Page 362: Premium System - If Equipped
360 STARTING AND OPERATING 5. Once you repair or replace the original road tire and reinstall it on the vehicle in place of the compact spare, the TPMS will update automatically and the TPMS Telltale light will turn off, as long as no tire pressure is below the low-pressure warning limit in any of the four active road tires.
Page 363 Electronic Vehicle Information Center (EVIC) will display a graphic showing the pressure values of each tire with the low tire pressure values flashing. Should this occur, you should stop as soon as possible and inflate the tires with low pressure (those flashing in the EVIC graphic) to the vehicle’s recommended cold placard pressure value.
Page 364 362 STARTING AND OPERATING If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the Tire Pressure Monitoring Telltale light will no longer flash, and the CHECK TPM SYS- TEM message will no longer display, and a pressure value will display in place of the dashes.
Page 365: General Information
light will remain on and a chime will sound. In addition, the graphic in the EVIC will still display a flashing pressure value. 3. After driving the vehicle for up to 10 minutes above 15 mph (25 km/h), the TPMS Telltale light will flash on and off for 75 seconds and then remain on solid.
Page 366: Flexible Fuel- 2.7L Engines Only (Except California Emission States)
364 STARTING AND OPERATING The tire pressure sensors are covered under one of the following licenses: United States ..... KR5S120123 Canada .
Page 367: Ethanol Fuel (E-85)
Along with the special E-85 fuel filler cap, your vehicle may display a badge, which also indicates it can operate on E-85. E-85 Badge STARTING AND OPERATING 365 ETHANOL FUEL (E-85) E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline.
Page 368: Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles
366 STARTING AND OPERATING For best results, a refueling pattern that avoids alternat- ing between E-85 and unleaded gasoline is recom- mended. When you do switch fuel types it is recommended that: you do not add less than 5 gal (19 L) when refueling you drive the vehicle immediately after refueling for at least 5 miles (8 km) Observing these precautions will avoid possible hard...
Page 369: Starting
STARTING The characteristics of E-85 fuel make it unsuitable for use when ambient temperatures fall below 0°F (-18°C). In the range of 0°F (-18°C) to 32°F (0°C), you may experience an increase in the time it takes for your engine to start, and a deterioration in driveability (sags and/or hesitations) until the engine is fully warmed up.
Page 370: Fuel Requirements
368 STARTING AND OPERATING FUEL REQUIREMENTS 2.4L and 2.7L Engines 2.4L and 2.7L Engines are designed to meet all emissions regulations and provide ex- cellent fuel economy and performance when using high-quality unleaded “regu- lar” gasoline having an octane rating of 87. The use of premium gasoline is not recom- mended.
Page 371: Reformulated Gasoline
as hard starting, stalling, and hesitations. If you experi- ence these symptoms, try another brand of gasoline before considering service for the vehicle. Over 40 auto manufacturers worldwide have issued and endorsed consistent gasoline specifications (the World Wide Fuel Charter, WWFC) which define fuel properties necessary to deliver enhanced emissions, performance, and durability for your vehicle.
Page 372: Mmt In Gasoline
370 STARTING AND OPERATING CAUTION! For vehicles equipped with a 2.4L or 3.5L engine, DO NOT use gasoline containing Methanol or E85 Etha- nol. Use of these blends may result in starting and driveability problems and may damage critical fuel system components.
Page 373: Materials Added To Fuel
Materials Added to Fuel All gasoline sold in the United States is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and they would result in additional cost. Therefore, you should not have to add anything to the fuel.
Page 374: Carbon Monoxide Warnings
372 STARTING AND OPERATING Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
Page 375 Fuel Filler Cap (Gas Cap) NOTE: When removing the fuel filler cap, lay the cap tether in the hook, located on the fuel filler door rein- forcement. STARTING AND OPERATING 373 CAUTION! Damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap (gas cap).
Page 376: Loose Fuel Filler Cap Message
374 STARTING AND OPERATING WARNING! Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. Never add fuel to the vehicle when the engine is running. A fire may result if gasoline is pumped into a portable container that is inside of a vehicle.
Page 377: Vehicle Loading
VEHICLE LOADING The load carrying capacity of your vehicle is shown on the “Vehicle Certification Label.” This information should be used for passenger and luggage loading as indicated. Do not exceed the specified Gross Vehicle Weight Rating (GVWR) or the Gross Axle Weight Rating (GAWR). Vehicle Certification Label Your vehicle has a Vehicle Certification Label affixed to the rear of the driver’s door.
Page 378: Overloading
376 STARTING AND OPERATING WARNING! Because the front wheels steer the vehicle, it is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident.
Page 379: Trailer Towing
A loaded vehicle is shown in the illustration. Note that neither the GVWR nor the GAWR capacities have been exceeded. EXAMPLE ONLY Front Axle Empty Weight 2054 lbs (932 kg) Load (including driver, 271 lbs passengers, and cargo) (123 kg) Total 2325 lbs (1055 kg)
Page 380 378 STARTING AND OPERATING Gross Trailer Weight (GTW) The Gross Trailer Weight (GTW) is the weight of the trailer plus the weight of all cargo, consumables, and equipment (permanent or temporary) loaded in or on the trailer in its loaded and ready for operation condition. The recommended way to measure GTW is to put your fully loaded trailer on a vehicle scale.
Page 381 Frontal Area Frontal area is the maximum height and maximum width of the front of a trailer. Trailer Sway Control — Electronic Refer to “TSC (Trailer Sway Control)” under “Electronic Brake Control System” in this section for information on this system. Trailer Sway Control —...
Page 382 380 STARTING AND OPERATING WARNING! An improperly adjusted weight distributing hitch system may reduce handling, stability, braking performance, and could result in an accident. Weight distributing systems may not be compatible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputable recreational vehicle dealer for additional information.
Page 383: Trailer Hitch Classification
Improper Adjustment of Weight Distributing System Trailer Hitch Classification Your vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional Trailer Tow Prep Package. See your authorized dealer for package content. STARTING AND OPERATING 381 The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can...
Page 384: Trailer Towing Weights (Maximum Trailer Weight Ratings)
382 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ GCWR (Gross Com- Transaxle bined Wt. Rating) 2.4L Automatic 6,000 lbs (2,722 kg) 7,300 lbs (3,311 kg) 2.7L/3.5L (with out Trailer Tow 7,300 lbs (3,311 kg)
Page 385 Engine/ GCWR (Gross Com- Transaxle bined Wt. Rating) 8,300 lbs (3,765 kg) 8,300 lbs (3,765 kg) 3.5L (with Trailer Tow Prep Package 8,300 lbs (3,765 kg) (AHT) 8,300 lbs (3,765 kg) NOTE: The trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the Tire and Loading Information placard.
Page 386: Trailer And Tongue Weight
384 STARTING AND OPERATING Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle.
Page 387: Towing Requirements
NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or authorized dealer-installed options must be considered as part of the total load on your vehicle. Refer to the “Tire and Loading Information” placard for the maximum combined weight of occupants and cargo for your vehicle.
Page 388 386 STARTING AND OPERATING WARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and that it will not shift during travel. When traile- ring cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.
Page 389 4. Tongue weight rating for the trailer hitch utilized. (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight.) Towing Requirements — Tires − Do not attempt to tow a trailer while using a compact spare tire.
Page 390 388 STARTING AND OPERATING actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required. − Trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs (907 kg).
Page 391 STARTING AND OPERATING 389 The Trailer Tow Package may include a 4- and 7-pin wiring harness. Use a factory approved trailer harness and connector. NOTE: Do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector.
Page 392: Towing Tips
390 STARTING AND OPERATING 7-Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Towing Tips — Automatic Transaxle The DRIVE range can be selected when towing. How- ever, if frequent shifting occurs while in this range, select the “3”...
Page 393 NOTE: Check the 4-speed automatic transaxle fluid level before towing. The 6-speed transaxle is sealed and the fluid level cannot be checked. See your authorized dealer for assistance. Towing Tips — Electronic Speed Control (If Equipped) − Don’t use in hilly terrain or with heavy loads. −...
Page 394: Recreational Towing (Behind Motorhome, Etc.)
392 STARTING AND OPERATING Towing Tips — Cooling System To reduce potential for engine and transaxle overheating, take the following actions: − City Driving When stopped for short periods, put transaxle in NEU- TRAL and increase engine idle speed. − Highway Driving Reduce speed.
Page 395: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....394 If Your Engine Overheats ....394 Engine Oil Overheating —...
Page 396: Hazard Warning Flasher
394 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The HAZARD switch is located in the instrument panel switch bank above the climate controls. Push and release the switch to turn on the hazard warning flashers. When the hazard warning is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency.
Page 397: Engine Oil Overheating - 2.4L Gas And 2.0L Diesel Engines Only (If Equipped)
CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads “H,” safely pull over and stop the vehicle. Idle the vehicle with the A/C turned off until the pointer drops back into the normal range. If the pointer remains on the “H,”...
Page 398: Jacking And Tire Changing
396 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.
Page 399: Spare Tire Location
Spare Tire Location The spare tire is stowed underneath the rear of the vehicle and is held in place by means of a cable winch mechanism. Preparations For Jacking 1. Park the vehicle on a firm level surface as far from the edge of the roadway as possible.
Page 400 398 WHAT TO DO IN EMERGENCIES Lowering/Raising Spare Tire NOTE: Assemble components 2 and 3 by seating the small ball at the end of component 2 in the small hole at the end of component 3. This will lock these components together.
Page 401: Spare Tire Stowage
4. Tilt the retainer at the end of the winch cable and remove it from the center of the wheel. Spare Tire Retainer WHAT TO DO IN EMERGENCIES 399 Spare Tire Stowage NOTE: On Seven-Passenger Models, fold the third-row passenger seats flat. This will provide more space when accessing the jacking tools and when operating the winch mechanism.
Page 402 400 WHAT TO DO IN EMERGENCIES Lowering/Raising Spare Tire NOTE: Assemble components 2 and 3 by seating the small ball at the end of component 2 in the small hole at the end of component 3. This will lock these components together.
Page 403: Jacking Instructions
4. Tilt the retainer at the end of the winch cable and drop it through the center of the wheel. Then place the spare tire with the cable and retainer underneath the vehicle. Spare Tire Retainer WHAT TO DO IN EMERGENCIES 401 5.
Page 404 402 WHAT TO DO IN EMERGENCIES WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. Block the wheel diagonally opposite the wheel to be raised.
Page 405 WHAT TO DO IN EMERGENCIES 403 Jack Engagement Locations...
Page 406 404 WHAT TO DO IN EMERGENCIES 4. Raise the vehicle by turning the jack screw clockwise with the jack handle. Raise the vehicle until the tire just clears the road surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability.
Page 407 Refer to “Compact Spare Tire” and to “Limited-Use Spare” under “Tires — General Information” in Sec- tion 5 for additional warnings, cautions, and informa- tion about the spare tire, its use, and operation. 7. Install the wheel nuts with the cone shaped end of the nut toward the wheel.
Page 408 406 WHAT TO DO IN EMERGENCIES 11. Place the deflated (flat) tire in the cargo area. Do not stow the deflated tire in the spare tire stowage location. Have the deflated (flat) tire repaired or replaced as soon as possible. 12.
Page 409: Jump-Starting Procedures
JUMP-STARTING PROCEDURES WARNING! Take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is ON. You can be hurt by the fan. Do not attempt to push or tow your vehicle to get it started.
Page 410 408 WHAT TO DO IN EMERGENCIES 1. Wear eye protection and remove any metal jewelry such as watchbands or bracelets that might make an inadvertent electrical contact. 2. When boosting from a battery in another vehicle, park that vehicle within booster cable reach, but without allowing the vehicles to touch.
Page 411 1 — Positive Terminal 2 — Negative Terminal 6. If the vehicle is equipped with Sentry Key Immobi- lizer, turn the ignition switch to the ON position for three seconds before moving the ignition switch to the START position. WHAT TO DO IN EMERGENCIES 409 7.
Page 412: Freeing A Stuck Vehicle
410 WHAT TO DO IN EMERGENCIES NOTE: Refer to “Maintenance Procedures” in Section 7 for information on accessing the battery for service or replacement. WARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent;...
Page 413 WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause axle and tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck, and don’t let anyone near a spinning wheel, no matter what the speed.
Page 414: Towing A Disabled Vehicle
412 WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE Without The Ignition Key Front Wheel Drive (FWD) Special care must be taken when the vehicle is towed with the ignition in the LOCK position. Flat bed towing is the preferred towing method. However, if a flat bed towing vehicle is not available, a wheel lift towing vehicle may be used.
Page 415: Towing This Vehicle Behind Another Vehicle With A Tow Dolly
If you must use the accessories (wipers, defrosters, etc.) while being towed, the key must be in the ON position, not the ACC position. Make certain the transaxle remains in NEUTRAL. Front Wheel Drive (FWD) Your vehicle may be towed under the following condi- tions: The shift lever must be in NEUTRAL, the distance to be traveled must not exceed 15 mi (25 km), and the towing speed must not exceed 25 mph (40 km/h).
Page 416 414 WHAT TO DO IN EMERGENCIES All Wheel Drive (AWD) CAUTION! The manufacturer does not recommend towing an All-Wheel Drive (AWD) on a tow dolly. Vehicle damage may occur.
Page 417: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS 2.4L Engine Compartment ....418 2.7L Engine Compartment ....419 3.5L Engine Compartment .
Page 418 416 MAINTAINING YOUR VEHICLE A/C Air Filter — If Equipped ... . 434 Power Steering — Fluid Check ... . 436 Front Suspension Ball Joints .
Page 419 License Plate Light ....470 Fluids And Capacities ....472 Fluids, Lubricants, And Genuine Parts .
Page 420: 2.4L Engine Compartment
418 MAINTAINING YOUR VEHICLE 2.4L ENGINE COMPARTMENT 1 — Coolant Bottle 2 — Engine Coolant Reservoir 3 — Power Steering Fluid 4 — Engine Oil Dipstick 5 — Engine Oil Fill 6 — Automatic Transaxle Dipstick 7 — Power Steering Fluid Reservoir 8 —...
Page 421: L Engine Compartment
2.7L ENGINE COMPARTMENT 1 — Coolant Bottle 2 — Coolant Pressure Cap 3 — Power Steering Fluid 4 — Engine Oil Fill 5 — Engine Oil Dipstick 6 — Automatic Transaxle Dispstick MAINTAINING YOUR VEHICLE 419 7 — Brake Fluid Reservoir 8 —...
Page 422: 3.5L Engine Compartment
420 MAINTAINING YOUR VEHICLE 3.5L ENGINE COMPARTMENT 1 — Coolant Bottle 2 — Coolant Pressure Cap 3 — Power Steering Fluid 4 — Engine Oil Fill 5 — Engine Oil Dipstick 6 — Brake Fluid Reservoir 7 — Remote Jump-Start Positive Battery Post 8 —...
Page 423: Onboard Diagnostic System - Obd Ii
ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transaxle control systems. When these systems are oper- ating properly, your vehicle will provide excellent per- formance and fuel economy, as well as engine emissions well within current government regulations.
Page 424: Emissions Inspection And Maintenance Programs
422 MAINTAINING YOUR VEHICLE off the message. If the problem persists, the message will appear the next time the vehicle is started. A loose, improperly installed, or damaged fuel filler cap may also turn on the MIL. EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of this vehicle’s emissions control system.
Page 425: Replacement Parts
5. Approximately 15 seconds later, one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition key or start the engine. This means that the vehicle’s OBD II system is not ready and you should not proceed to the I/M station.
Page 426: Authorized Dealer Service
424 MAINTAINING YOUR VEHICLE AUTHORIZED DEALER SERVICE Your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting any procedure yourself.
Page 427 MAINTAINING YOUR VEHICLE 425 The best time to check the engine oil level is about five minutes after a fully warmed engine is shut off. Do not check oil level before starting the engine after it has sat overnight. Checking engine oil level when the engine is cold will give you an incorrect reading.
Page 428 426 MAINTAINING YOUR VEHICLE CAUTION! Do not overfill the engine. Overfilling the engine will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature. This could damage your engine. Change Engine Oil The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.
Page 429 Engine Oil Viscosity (SAE Grade) — 2.4L and 2.7L Engines SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil filler cap also shows the recommended engine oil viscosity for your engine.
Page 430: Engine Oil Filter
428 MAINTAINING YOUR VEHICLE Disposing of Used Engine Oil and Oil Filters Care should be taken in disposing of used engine oil and oil filters from your vehicle. Used oil and oil filters, indiscriminately discarded, can present a problem to the environment.
Page 431: Spark Plugs
Spark Plugs Spark plugs must fire properly to assure engine perfor- mance and emissions control. New plugs should be installed at the specified mileage. The entire set should be replaced if there is any malfunction due to a faulty spark plug.
Page 432 430 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition.
Page 433: Maintenance-Free Battery
In unusual situations involving grossly malfunctioning engine operation, a scorching odor may indicate severe and abnormal catalyst overheating. If this occurs, safely bring the vehicle to a complete stop, shut the engine OFF, and allow the vehicle to cool. Thereafter, obtain service, including a tune-up to manufacturer’s specifications im- mediately.
Page 434 432 MAINTAINING YOUR VEHICLE WARNING! Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin, or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water.
Page 435: Air Conditioner Maintenance
Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at this time.
Page 436: A/C Air Filter - If Equipped
434 MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluoro- carbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by authorized dealers or other service facilities using recovery and recycling equipment.
Page 437 Glove Box Removal 3. Pivot the glove box downward. 4. Disengage the two retaining tabs that secure the filter cover to the HVAC housing and remove the cover. MAINTAINING YOUR VEHICLE 435 A/C Air Filter Replacement 5. Remove the A/C air filter by pulling it straight out of the housing.
Page 438: Power Steering - Fluid Check
436 MAINTAINING YOUR VEHICLE CAUTION! The A/C air filter is labeled with an arrow to indicate airflow direction through the filter. Failure to install the filter properly will result in the need to replace it more often. 7. Reinstall the glove box door. Make sure that the hinges are seated fully as you raise the door.
Page 439: Front Suspension Ball Joints
Front Suspension Ball Joints There are two front suspension lower ball joints that are permanently lubricated. Inspect these ball joints when other maintenance is performed. A damaged seal and the corresponding potentially damaged ball joint must be replaced. Steering Linkage The tie rod end ball joints should be inspected for external leakage and damage when other maintenance is performed.
Page 440: Windshield Washers/Rear Window Washer
438 MAINTAINING YOUR VEHICLE Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield or rear window. Avoid using the wiper blades to remove frost or ice from the windshield or rear window.
Page 441: Exhaust System
WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
Page 442: Cooling System
440 MAINTAINING YOUR VEHICLE Cooling System WARNING! When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the LOCK position. The fan is tempera- ture controlled and can start at any time the ignition switch is in the ON position.
Page 443 Cooling System — Drain, Flush, and Refill The system should be drained, flushed, and refilled at the intervals shown in the Maintenance Schedule in Section If the solution is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner.
Page 444 442 MAINTAINING YOUR VEHICLE Adding Coolant Your vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This coolant can be used up to five years or 100,000 mi (160 000 km) before replacement. To prevent reducing this extended maintenance period, it is important that you use the same coolant throughout the life of your vehicle.
Page 445 The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. WARNING! The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety pre- caution. Never add coolant when the engine is overheated.
Page 446 444 MAINTAINING YOUR VEHICLE Six Cylinder Engines — the level of the coolant in the pressurized coolant bottle should be between the “COLD” and “FULL” range on the bottle when the engine is cold. The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for coolant freeze point or replacing coolant.
Page 447: Hoses And Vacuum/Vapor Harnesses
Maintain coolant concentration at 50% HOAT engine coolant (minimum) and distilled water for proper corrosion protection of your engine, which contains aluminum components. Make sure that the radiator and coolant recovery bottle overflow hoses are not kinked or obstructed. Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean, also.
Page 448: Fuel System
446 MAINTAINING YOUR VEHICLE Fuel System The Electronic Fuel Injection high-pressure fuel system’s hoses and fittings have unique material characteristics that provide adequate sealing and resist attack by dete- riorated gasoline. You are urged to use only the manufacturer’s specified hoses and fittings, or their equivalent in material and specification, in any fuel system servicing.
Page 449 Ensure nylon tubing in these areas has not melted or collapsed. Inspect all hose clamps and couplings to make sure they are secure and no leaks are present. NOTE: Often, fluids such as oil, power steering fluid, and brake fluid are used during assembly plant operations to ease the assembly of hoses to couplings.
Page 450 448 MAINTAINING YOUR VEHICLE Clean the top of the master cylinder area before removing the cap. If necessary, add fluid to bring the fluid level up to the requirements described on the brake fluid reser- voir. Overfilling of fluid is not recommended because it may cause leaking in the system.
Page 451: Automatic Transaxle
CAUTION! Do not allow petroleum-based fluid to contaminate the brake fluid. Seal damage may result. Automatic Transaxle The automatic transaxle and differential assembly are contained within a single housing. The fluid level in the automatic transaxle should be checked whenever the vehicle is serviced. Operation with an improper fluid level will greatly reduce the life of the transaxle and the fluid.
Page 452 450 MAINTAINING YOUR VEHICLE 6. Remove the dipstick and determine if the fluid is hot or cold. Hot fluid is approximately 180°F (82°C), which is the normal operating temperature after the vehicle is driven at least 15 mi (24 km). Hot fluid cannot be held comfortably between the fingertips.
Page 453: Front And Rear Wheel Bearings
Fluid and Filter Changes Change the automatic transaxle fluid and filter at the intervals shown in the “Maintenance Schedule” in this manual. In addition, change the fluid and filter if the transaxle is disassembled for any reason. Selection of Lubricant It is important that the proper lubricant is used in the transaxle to assure optimum transaxle performance.
Page 454: Appearance Care And Protection From Corrosion
452 MAINTAINING YOUR VEHICLE Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.
Page 455 Use Mopar Cleaner Wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint. Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch...
Page 456 454 MAINTAINING YOUR VEHICLE Use Mopar touch up paint on scratches as soon as possible. Your authorized dealer has touch up paint to match the color of your vehicle. Wheel and Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome plated wheels should be cleaned regularly with a mild soap and water to prevent corrosion.
Page 457 Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and Mopar Total Clean.
Page 458 456 MAINTAINING YOUR VEHICLE Cleaning Headlights Your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth.
Page 459: Cleaning The Cupholders
Seat Belt Maintenance Do not bleach, dye, or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water.
Page 460 458 MAINTAINING YOUR VEHICLE CAUTION! When installing the power module cover, it is important to ensure the cover is properly posi- tioned and fully latched. Failure to do so may allow water to get into the TIPM, and possibly result in an electrical system failure. When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating.
Page 461 Cartridge Mini- Cavity Fuse Fuse 30 Amp Anti-Lock Brake Sys- Pink tem (ABS) Valve/ — Electronic Stability Program (ESP) 40 Amp Power Memory Seat - — Green if equipped 40 Amp Flex Fuel/PZEV Mo- — Green tor - if equipped 30 Amp (If Equipped) Head- Pink...
Page 462 460 MAINTAINING YOUR VEHICLE Cartridge Mini- Cavity Fuse Fuse 25 Amp — White 15 Amp — Blue 20 Amp — Yellow 20 Amp — Yellow 10 Amp — 25 Amp — Natural 20 Amp — Yellow Description Cavity Sunroof Module - if equipped Center High Mounted Stop Light (CHMSL)
Page 463 Cartridge Mini- Cavity Fuse Fuse 15 Amp Vanity Lamps/ Blue Hands-Free Module (HFM) - if equipped, Remote Display - if equipped, Satellite Digital Audio Re- ceiver (SDARS) - if — equipped, Universal Garage Door Opener (UGDO) - if equipped, Vanity Light, Video Enter- tainment System (VES)™...
Page 464 462 MAINTAINING YOUR VEHICLE Cartridge Mini- Cavity Fuse Fuse 10 Amp — 15 Amp — Blue 15 Amp — Blue 25 Amp — Natural Description Cavity Occupant Restraint Controller (ORC)/ Occupant Classifica- tion Module (OCM) Left Park/Side Marker/Running/Tail Lights, License Lights Right Park/Side Marker/Running/Tail Lights...
Page 465 Cartridge Mini- Cavity Fuse Fuse 20 Amp Fuel Pump/Diesel — Yellow Lift Pump 10 Amp Power MIRRORS — Switch/Drivers Win- dow Switch 10 Amp Steering Column — Lock, Wireless Igni- tion Node (WIN) 10 Amp NGC (Powertrain Control Module)/ — Transmission Feed (Batt) 10 Amp...
Page 466: Vehicle Storage
464 MAINTAINING YOUR VEHICLE Cartridge Mini- Cavity Fuse Fuse 10 Amp — 25 Amp — Natural — — — — — — — — — — Description Anti-Lock Brake Sys- tem (ABS), Electronic Stability Program (ESP), STOP LIGHT Switch Lock/Unlock Motors Ignition Run/ VEHICLE STORAGE Accessory Relay...
Page 467: Replacement Bulbs
REPLACEMENT BULBS All the inside bulbs are brass or glass wedge base. Aluminum base bulbs are not approved and should not be used for replacement. LIGHT BULBS — Interior Courtesy/Reading Lights (Incandescent) ..578 Courtesy/Reading Lights (Optional LED) .
Page 468: Bulb Replacement
466 MAINTAINING YOUR VEHICLE BULB REPLACEMENT Low Beam Headlight, High Beam Headlight, Front Turn Signal/Park Light, Side Marker Light 1. Open the hood. NOTE: It may be necessary to remove the air cleaner filter housing and position the Totally Integrated Power Module (TIPM) aside to replace certain the lights in the left headlight housing.
Page 469: Front Fog Light
CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. 4. Install the bulb and connector assembly into the headlight housing and rotate it ⁄...
Page 470: Tail/Stop Light, Rear Turn Signal Light, Tail Light, Backup Light
468 MAINTAINING YOUR VEHICLE CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. 4. Install the bulb and connector assembly into the fog light housing and rotate the connector to lock it in place.
Page 471 4. Rotate the applicable bulb’s electrical connector turn counterclockwise and remove it from the taillight housing. 1 — Tail/Stop Light Bulb 2 — Rear Turn Signal Light Bulb 5. Remove the bulb from the connector socket and install the replacement bulb. MAINTAINING YOUR VEHICLE 469 ⁄...
Page 472: License Light
470 MAINTAINING YOUR VEHICLE 1 — Tail Light Bulb 2 — Backup Light Bulb 5. Remove the bulb from the connector socket and install the replacement bulb. 6. Install the bulb and connector assembly into the housing and rotate the connector lock it in place.
Page 473 2. Insert a small flat-blade tool between the end of the lens with the locking tab and the surrounding housing and then pivot the tool to separate the lens from the housing. 3. Hold the lens with one hand and rotate the bulb’s electrical connector ⁄...
Page 474 472 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Component Fuel (approximate) Front Wheel Drive (FWD) Models with 2.4 Liter PZEV Engine FWD Models without 2.4 Liter PZEV Engine All-Wheel Drive Models Engine Oil with Filter 2.4 Liter Engine (SAE 5W-20, API Certified) 2.7 Liter Engine (SAE 5W-20, API Certified) 3.5 Liter Engine (SAE 10W-30, API Certified) Cooling System *...
Page 475 Component 2.7 Liter Engine and Single- or Dual-Zone Climate Control System (Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula) or equiva- lent 2.7 Liter Engine and Three-Zone Climate Control System (Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula) or equivalent 3.5 Liter Engine and Single- or Dual-Zone Climate Control System (Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula) or equiva- lent 3.5 Liter Engine and Three-Zone Climate Control System (Mopar...
Page 476 474 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Engine Coolant Engine Oil (2.4L) Engine Oil (2.7L) Engine Oil (3.5L) Oil Filter (2.4L) Oil Filter (2.7L) Oil Filter (3.5L) Spark Plugs (2.4L) Fluids, Lubricants, and Genuine Parts Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent Use API Certified SAE 5W-20 Engine Oil meeting the requirements of Chrysler Material Standard MS-6395.
Page 477 Component Spark Plugs (2.7L) Spark Plugs (3.5L) Fuel Selection (2.4L) Fuel Selection (2.7L) Fuel Selection (2.7L - EXCEPT CALI- FORNIA EMISSION STATES) Fuel Selection (3.5L) Fluids, Lubricants, and Genuine Parts TE10MCC5 (Gap.050 in [1.27 mm]) ZFR5LP-13G (Gap.050 in [1.27 mm]) 87 Octane 87 Octane E-85 Ethanol...
Page 478 476 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transaxle Power Transfer Unit (PTU) Rear Drive Assembly (RDA) Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts Mopar ATF+4 Automatic Transmission Fluid Mopar Gear Lubricant 75W-90 or equivalent Mopar Gear Lubricant 75W-90 or equivalent. Mopar DOT 3, SAE J1703 or equivalent should be used.
Page 479 MAINTENANCE SCHEDULES CONTENTS Emissions Control System Maintenance ..478 Maintenance Schedule ....478 Required Maintenance Intervals ... 481...
Page 480 478 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type, must be done at the times or mileages specified to ensure the continued proper functioning of the Emissions Con- trol System. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
Page 481 NOTE: The oil change indicator message will not monitor the time since the last oil change. Change your vehicles oil if it has been six months since your last oil change, even if the oil change indicator message is NOT illuminated.
Page 482 480 MAINTENANCE SCHEDULES At Each Stop for Fuel Check the engine oil level. Refer to “Engine Oil” under “Maintenance Procedures” in Section 7. Check the windshield washer solvent and add if required. Once a Month Check tire pressure and look for unusual wear or damage.
Page 483 Required Maintenance Intervals Maintenance Items Change the engine oil and engine oil filter. Rotate the tires. If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if nec- essary. Inspect the brake linings, and replace if necessary. Replace the air conditioning filter (if equipped).
Page 484 482 MAINTENANCE SCHEDULES Maintenance Items Replace the spark plugs on 2.4L and 2.7L engines. Change Rear Drive Assembly (RDA) fluid. Change Power Transfer Unit (PTU) fluid. Change the automatic transaxle fluid and filter if us- ing your vehicle for any of the following: police, taxi, fleet, or frequent trailer towing.
Page 485 † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
Page 487 IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......487 Prepare For The Appointment .
Page 488 486 IF YOU NEED CONSUMER ASSISTANCE Publication Order Forms ....492 Department Of Transportation Uniform Tire Quality Grades ..... 493 Treadwear .
Page 489: Suggestions For Obtaining Service For Your Vehicle
SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty.
Page 490: Chrysler Llc Customer Center
488 IF YOU NEED CONSUMER ASSISTANCE high quality service. The manufacturer’s authorized deal- ers have the facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer’s service manager first.
Page 491: In Mexico Contact
In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P. 05109 Mexico, D. F. In Mexico City: 5081-4568 Outside Mexico City: 1-800-505-1300 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommuni- cation Devices for the Deaf) equipment at its Customer Center.
Page 492: Warranty Information (U.s. Vehicles Only)
490 IF YOU NEED CONSUMER ASSISTANCE Contract, and you require service after the manufactur- er’s New Vehicle Limited Warranty expires, please refer to the contract documents, and contact the person listed in those documents. We appreciate that you have made a major investment when you purchased the vehicle.
Page 493: Mopar Parts
MOPAR PARTS Mopar fluids, lubricants, parts, and accessories are available from an authorized dealer. They will help keep the vehicle operating at its best. REPORTING SAFETY DEFECTS In The 50 United States And Washington, D.C. If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the...
Page 494: Publication Order Forms
492 IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mas- tercard, American Express, and Discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form.
Page 495: Traction Grades
Call toll free at: 1–800–890–4038 (U.S.) 1–800–387–1143 (Canada) Visit us on the Worldwide Web at: www.techauthority.com DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle.
Page 496 494 IF YOU NEED CONSUMER ASSISTANCE WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory...
Page 497 INDEX...
Page 498 496 INDEX About Your Brakes ....323,326 ABS (Anti-Lock Brake System) ..215,327,328 Adding Engine Coolant (Antifreeze) .
Page 499 Audio Systems (Radio) ....234,266 Auto Down Power Windows ....35 Auto Unlock, Doors .
Page 500 498 INDEX Brake Assist System ..... . 330 Brake Assist Warning Light ....216 Brake Control System, Electronic .
Page 501 Cargo Tie-Downs ......189 Cargo (Vehicle Loading) ....188,375 Catalytic Converter .
Page 502 500 INDEX Console, Overhead ..... . . 162 Contract, Service ......489 Converter, Catalytic .
Page 503 Disabled Vehicle Towing ....412 Disposal Antifreeze (Engine Coolant) ....443 Engine Oil .
Page 504 502 INDEX Air Cleaner ......429 Block Heater ......311 Break-In Recommendations .
Page 505 Filters Air Cleaner ......429 Air Conditioning ....301,434 Automatic Transaxle .
Page 506 504 INDEX Additives ......371 Clean Air ......369 Conserving .
Page 507 Gross Vehicle Weight Rating ... . . 375,377 GVWR ....... 375 Hands-Free Phone (UConnect ) .
Page 508 506 INDEX Key ....... 12,14 Ignition Key Removal ..... 14 Illuminated Entry .
Page 509 Latch Plate ......42 Latches ....... . 81 Hood .
Page 510 508 INDEX Illuminated Entry ..... . . 20 Instrument Cluster ....146,205 Intensity Control .
Page 511 Lubrication, Body ..... . . 437 Luggage Rack (Roof Rack) ....196 Lumbar Support .
Page 512 510 INDEX Occupant Restraints ..... . . 39 Octane Rating, Gasoline (Fuel) ... . 368,474 Odometer Trip .
Page 513 Phone, Cellular ....93,266,267 Phone, Hands-Free (UConnect ) ..93,266,267 Placard, Tire and Loading Information ..341 Port Universal Serial Bus (USB) .
Page 514 512 INDEX Rear Cup Holder ......178 Rear Liftgate ......38 Rear Seat, Folding .
Page 515 Safety Checks Inside Vehicle ....80 Safety Checks Outside Vehicle ....81 Safety Defects, Reporting .
Page 516 514 INDEX Security Alarm (Theft Alarm) ... . . 18,208 Selection of Coolant (Antifreeze) ..441,474 Selection of Oil ......426 Sentry Key (Immobilizer) .
Page 517 Engine Fails to Start ....310 Remote ......27 Starting and Operating .
Page 518 516 INDEX Tire and Loading Information Placard ..341 Tire Identification Number (TIN) ... . . 340 Tire Markings ......337 Tire Safety Information .
Page 519 Towing Vehicle Behind a Motor Home ..392 Traction ......320 Traction Control .
Page 520 518 INDEX Uniform Tire Quality Grades ....493 Universal Consumer Interface (UCI) Connector . . . 278 Universal Serial Bus (USB) Port ... 234,266 Universal Transmitter .
Page 521 Wheel Bearings ......451 Wheel Nut Torque ..... . . 406 Wind Buffeting .
Page 522 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
Page 523 Fourth Edition Printed in U.S.A.

Dodge 2009 Journey Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

Quick Links

Chapters

Related Manuals for Dodge 2009 Journey

Summary of Contents for Dodge 2009 Journey