Page 1 Caravan 2 0 0 8 O W N E R ’ S M A N U A L...
Page 2 VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents.
Page 3: Introduction 3
TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 5 CONTENTS Introduction ......4 How To Use This Manual ....4 Warnings And Cautions .
Page 6: Introduction
4 INTRODUCTION INTRODUCTION This Owner’s Manual has been prepared with the assis- tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully.
Page 7 INTRODUCTION 5...
Page 8: Warnings And Cautions
6 INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual you may miss important infor- mation.
Page 9: Vehicle Modifications/Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 11: Table Of Contents
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Wireless Ignition Node (WIN) ... . .12 Sentry Key Immobilizer System .
Page 12 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Sliding Side Door — If Equipped ..42 Sliding Side Door Child Protection Lock ..46 Liftgate .......48 Power Liftgate —...
Page 13: Things To Know Before Starting Your Vehicle
Restraining Infants And Small Children With Seat Delete Feature (Commercial Vehicles Only) ..90 Engine Break-In Recommendations ...93 Safety Tips ......93 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 Safety Checks You Should Make Inside The Vehicle .
Page 14: Things To Know Before Starting Your Vehicle 9
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Your vehicle uses a keyless ignition system. This system consists of a Remote Keyless Entry (RKE) transmitter with integrated ignition Key and a Wireless Ignition Node (WIN) with integral ignition switch. You can insert the double-sided key into the ignition switch with either side up.
Page 15 The valet key allows for entry into the vehicle should the battery in the vehicle or the transmitter go dead. The valet key is also for locking the glove box. You can keep the valet key with you when valet parking. To remove the valet key from the transmitter, slide the mechanical latch at the top of the transmitter sideways with your thumb and then pull the key out with your...
Page 16 14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Insert the integrated ignition key into the ignition switch. 3. Turn the ignition switch to the START position and release it as soon as the starter engages. The starter motor will continue to run and will disengage automatically when the engine begins running.
Page 17: Sentry Key Immobilizer System
Key-In-Ignition Reminder If you open the driver’s door with the integrated ignition key in the ignition, a chime will sound to remind you to remove the key. NOTE: The Key-In-Ignition reminder only sounds when the integrated ignition key is placed in the OFF or ACC position.
Page 18: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • The Sentry Key Immobilizer system is not compatible with aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. • Exxon/Mobil Speedpass™, additional RKE transmit- ters, or any other transponder-equipped components on the same key chain will not cause a fault unless the additional part is physically held against the trans-...
Page 19 programming a blank transmitter to the vehicle electron- ics. A blank transmitter is one that has never been programmed. NOTE: When having the Sentry Key system serviced, bring all vehicle RKE transmitters with you to the authorized dealer. Customer Key Programming If you have two valid RKE transmitters with integrated keys, you can program new transmitters to the system by performing the following steps:...
Page 20: Security Alarm System - If Equipped
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If a programmed key is lost, see your authorized dealer to have all remaining keys erased from the sys- tem’s memory. This will prevent the lost key from starting your vehicle. The remaining keys must then be reprogrammed.
Page 21 Arming The System Remove the key from the ignition switch and either press a power door lock switch while the driver or passenger door is open or press the LOCK button on the Remote Keyless Entry (RKE) transmitter. After all the doors are locked and closed the Vehicle Security Alarm Indicator Light in the instrument cluster will flash rapidly to signal that the system is arming.
Page 22: Illuminated Entry System - If Equipped
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE previously described arming sequences has occurred, the system will arm regardless of whether you are in the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound. If this occurs, disarm the system.
Page 23: Remote Keyless Entry (Rke) - If Equipped
REMOTE KEYLESS ENTRY (RKE) — IF EQUIPPED This system allows you to lock or unlock the doors and liftgate, and activate the PANIC alarm, optional power liftgate, left power sliding door, and right power sliding door from distances up to about 23 ft (7 m) using a hand-held radio RKE transmitter.
Page 24 22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seven-button transmitters will provide functions that allow the same basic operation as the three-button, but may also be used to OPEN/CLOSE the optional power liftgate, left power sliding door, or right power sliding door.
Page 25 • For vehicles not equipped with the EVIC, the Remote UNLOCK feature can be enabled or disabled by per- forming the following procedure: 1. Perform this operation while standing outside the vehicle. 2. Press the LOCK button for five to ten seconds. 3.
Page 26 24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Using The PANIC Alarm To turn the PANIC Alarm feature ON or OFF, press and hold the PANIC button on the RKE transmitter for at least one second and release. When the PANIC Alarm is on, the headlights and park lights will flash, the horn will pulse on and off and the interior lights will turn on.
Page 27 Open/Close Power Left Power Sliding Door — If Equipped Press the Left Power Sliding Door button twice on the RKE transmitter within five seconds to Open/Close Power Left Power Sliding Door. If the button is pushed while the door is being power-closed, the door will reverse to the full open position.
Page 28 26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The table below explains the Lamp Flash options. Which Turn Function Signal Lamps Lock Unlock 1st Press Left Side Unlock All Doors Left Side Left Side Right Side Right Side Liftgate Programming Additional RKE Transmitters Refer to Sentry Key Immobilizer System “Customer Key Programming.”...
Page 29 Battery Replacement 2. Remove and replace the battery. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch the battery, clean it with rubbing alcohol. 3. Reposition the access door panel over the battery opening and snap into place.
Page 30: Remote Starting System - If Equipped
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE STARTING SYSTEM — IF EQUIPPED Remote Starting conveniently starts the engine from outside the vehicle by using the Remote Keyless Entry (RKE) transmitter while maintaining the Security Alarm System. The Remote Starting System has a targeted range of 328 ft (100 m).
Page 31 To Enter Remote Start Mode Remote Starting Button Press and release the Remote Start button on the RKE transmitter twice, within five seconds. The parking lights will flash and the horn will THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 honk twice (if programmed).
Page 32 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Enter the Vehicle After Remote Start To enter the vehicle while the engine is running during a Remote Start, you must first unlock the vehicle using the UNLOCK button on the transmitter. After the vehicle is unlocked, you have 60 seconds to enter the vehicle, insert the key into the ignition switch and move it to the RUN position, otherwise the engine will cancel Remote Start-...
Page 33: Door Locks
To Turn Off the Engine While in Remote Start Mode Press and release the Remote Start button one time. NOTE: To avoid inadvertent shut downs, the system will disable the one time press of the Remote Start button for two seconds after receiving a valid Remote Start request.
Page 34: Power Door Locks - If Equipped
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the lock plunger is down when you shut the door, the door will lock. Therefore, make sure the keys are not inside the vehicle before closing the door. Sliding Door Lock Features WARNING! •...
Page 35 Driver Power Door Locks 1 - Unlock 2 - Lock If you press the power door lock switch while the key is in the ignition, and any front door is open, the power locks will not operate. This prevents you from acciden- tally locking your keys in the vehicle.
Page 36 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lock Doors Automatically — If Equipped If the Lock Doors Automatically feature is enabled, your door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h). The Lock Doors Automatically feature is enabled when your vehicle is shipped from the assembly plant and can be disabled by using the following procedure: •...
Page 37 The Lock Doors Automatically at 15 mph (24 km/h) feature can be reactivated by repeating the above men- tioned procedure or by performing the procedure in the EVIC, Customer Programmable Features section on ve- hicles so equipped. Unlock Doors Automatically On Exit — If Equipped The Unlock Doors Automatically On Exit feature unlocks all of the doors of the vehicle when any door is opened.
Page 38: Windows
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 7. To reactivate this feature, repeat the above steps. 8. If a chime is not heard, the program mode was canceled before the feature could be changed. If neces- sary, repeat the above procedure. The Unlock Doors Automatically On Exit feature can be reactivated by repeating the above mentioned procedure or by performing the procedure in the EVIC, Customer...
Page 39: Power Windows
POWER WINDOWS You can control all windows using switches on the driver’s door trim panel. The switches will operate only when the ignition switch is in the ON or ACC position and during power accessory delay. NOTE: Power Window switches will also remain active for up to 90 seconds after the ignition switch has been turned OFF, depending upon the accessory delay setting.
Page 40 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Window Lockout Switch — If Equipped The driver may lock out all power windows by depressing the bar switch just below the power window switches. Power Window Lockout Switch Front Passenger Power Window Switch There is a single switch on the front passenger’s door trim panel which operates the passenger door window and locks and unlocks all doors.
Page 41 Sliding Side Door Power Window Switch There is a single switch on each sliding side door which operates the sliding side door window. The switches will operate only when the ignition switch is in the ON or ACC position. Sliding Door Power Window Switch THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 NOTE: The sliding door windows do not fully open, stopping several inches above the window sill.
Page 42 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Up Feature With Anti–Pinch Protection — If Equipped The left front window switch may be equipped with an Auto Up feature. Lift the window switch to the second detent, release, and the window will go up automatically. To stop the window from going all the way up during the Auto Up operation, push down on the switch briefly.
Page 43: Sliding Side Door
2. Push the window switch down firmly to the second detent to open the window completely and continue to hold the switch down for an additional two seconds after the window is fully open. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears.
Page 44: Power Sliding Side Door - If Equipped
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • There is a hold-open latch that is activated when the sliding door is fully opened. This latch will keep your sliding door open on any incline. To close the sliding door after the hold-open latch is activated, you must rock the inside handle forward or pull outward on the outside handle.
Page 45 NOTE: The power sliding side door must be unlocked before the power sliding door switches will operate. Power Sliding Door Detail 1 — Heated Seat Switch 4 — Door Handle 5 — Power Sliding Door 2 — Power Window Switch Switch 3 —...
Page 46 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the power sliding side door is not in the full open or close position, it will fully open when a power sliding door switch is pressed. To close the door, wait until it is fully open and then press the switch again.
Page 47 You can turn the feature back on by repeating the above mentioned procedure. Power Sliding Side Door Master Lock Switch The power sliding side doors may also be opened by pressing the switches on the overhead console or the switches located on the trim panel just in front of the sliding door.
Page 48: Sliding Side Door Child Protection Lock
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Sliding Side Door Child Protection Lock To provide a safer environment for small children riding in the rear seats, the sliding doors are equipped with a child protection door lock system. NOTE: When the child lock system is engaged, the door can be opened only by using the outside door handle even though the inside door lock is in the unlocked position.
Page 49 NOTE: • After engaging the Child Protection Door Lock, al- ways test the door from the inside to make certain it is in the desired position. • When the Child Protection Door Lock system is en- gaged, (even if the inside door lock is in the unlocked position) the door can be opened only by using the outside door handle, the Remote Keyless Entry (RKE) transmitter, the switches on the overhead console, or...
Page 50: Liftgate
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LIFTGATE On vehicles equipped with power locks, the liftgate can be unlocked using the Remote Keyless Entry (RKE) transmitter button, or by activating the power door lock switches located on the front doors. To open the liftgate, depress the liftgate release handle located on the underside of the license plate bar and pull the liftgate open with one fluid motion.
Page 51: Power Liftgate - If Equipped
POWER LIFTGATE — IF EQUIPPED The power liftgate may be opened manually or by using the button on the Remote Keyless Entry (RKE) transmit- ter. Press the button on the transmitter twice within five seconds, to open the power liftgate. When the liftgate is fully open, pressing the button twice within five seconds, a second time, will close the liftgate.
Page 52 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The power liftgate may be closed by pressing the button, located in the upper left trim in the liftgate opening. Pushing once will only close the liftgate. This button cannot be used to open the liftgate. Liftgate Rear Switch WARNING! During power operation, personal injury or cargo...
Page 53 • The power liftgate must be in the full open or close positions for any of the buttons to operate. If the liftgate is not in the full open or close positions, it must be opened or closed manually. • If the liftgate release button is activated while the power liftgate is closing, the liftgate will reverse to the full open position.
Page 54: Storage Bin Safety Warning
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Gas props support the liftgate in the open position. However, because the gas pressure drops with tempera- ture, it may be necessary to assist the props when opening the liftgate in cold weather. STORAGE BIN SAFETY WARNING Safety Warnings WARNING!
Page 55 NOTE: Your vehicle may be built with a release strap or release lever attached to the Storage Bin Cover latch mechanism. Storage Bin Cover Emergency Release Lever — If Equipped As a security measure, your vehicle may be built with a Storage Bin Cover Emergency Release lever built into the storage bin cover latching mechanism.
Page 56: Storage Bin Cover Emergency Release Strap - If Equipped
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Storage Bin Cover Emergency Release Strap — If Equipped As a security measure, your vehicle may be built with a Storage Bin Cover Emergency Release strap built into the storage bin cover latching mechanism. Storage Bin Cover Emergency Release Strap NOTE: In the event of an individual being locked inside the storage bin, the storage bin cover can be opened from...
Page 57: Occupant Restraints
Reinstalling Storage Bin Cover Emergency Release Strap NOTE: Do not use the storage bin emergency release strap to lift the storage bin cover. The strap is intended for emergency release only. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems: •...
Page 58 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • All seat belt systems (except the driver’s, Swivel n’ Go, and third row center position) include Automatic Locking Retractors (ALRs), which lock the seat belt webbing into position by extending the belt all the way out and then adjusting the belt to the desired length to restrain a child seat or secure a large item in a seat.
Page 59: Lap/Shoulder Belts
Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle.
Page 60 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. •...
Page 61 2. The seat belt latch plate is near the seatback of the front seats and next to your arm in the rear seats. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap.
Page 62 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click”. Latch Plate To Buckle WARNING! • A belt that is buckled into the wrong buckle will not protect you properly.
Page 63 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.
Page 64 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection.
Page 65: Automatic Locking Retractors (Alr) Mode - If Equipped
pushing anywhere on the anchorage. To move the an- chorage downward, squeeze the actuation buttons while simultaneously pushing down on the anchorage assem- bly. As a guide, if you are shorter than average you will prefer a lower position, and if you are taller than average you will prefer a higher position.
Page 66: Seat Belt Pretensioners
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Pretensioners The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight about the occupant early in a collision.
Page 67: Seat Belts And Pregnant Women
NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or START position. DaimlerChrysler does not recom- mend deactivating BeltAlert . 1. With all doors closed and the ignition switch in any position except ON or START, buckle the driver’s seat belt.
Page 68: Seat Belt Extender
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Extender If a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your authorized dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long enough.
Page 69: Airbag System Components
window. If the vehicle is equipped with SABIC air bags, they are located above the side windows and their covers are also labeled: SRS AIRBAG. NOTE: Airbag covers may not be obvious in the interior trim; but they will open to allow airbag deployment. Airbag System Components The airbag system consists of the following: •...
Page 70 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The first stage inflator is triggered immediately during an impact that requires airbag deployment. The timing of the second stage determines whether the output force is low, medium, or high. If a low output is sufficient to meet the need, the second stage is expended later in the crash event.
Page 71 Thorax Airbag Label When the airbag deploys, it opens the seam between the front and side of the seat’s trim cover. Each airbag deploys independently, that is a left side impact deploys the left airbag only and a right-side impact deploys only the right airbag.
Page 72 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Side Airbag Inflatable Curtain (SABIC) — If Equipped SABIC Airbags offer side-impact and vehicle rollover protection to front and rear seat outboard occupants in addition to that provided by the body structure. Each airbag features inflated chambers placed adjacent to the head of each outboard occupant that reduce the potential for side-impact head injuries.
Page 73 moderate to severe side collisions. In certain types of collisions, both the front and side airbags may be trig- gered. However, even in collisions where the airbags work, you need the seat belts to keep you in the right position for the airbags to protect you properly. Here are some simple steps you can take to minimize the risk of harm from a deploying airbag.
Page 74: Airbag Deployment Sensors And Controls
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. If your vehicle has side airbags, do not lean against the door, airbags will inflate forcefully into the space between you and the door. 5. If the airbag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center.
Page 75 impact sensors signals, a central electronic ORC deploys the front airbags, side inflatable airbag curtains, side seat thorax airbags, and front seat belt pretensioners as re- quired for each type of impact. The ORC monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or ON position.
Page 76 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Front and Side Impact Sensors Impact Sensors trigger airbag deployment in front and side impacts, and aid the ORC in determining appropri- ate response to impact events. Additional sensors in the ORC determine the level of airbag deployment and provide verification.
Page 77 • Turns on the interior lights, which remain on as long as the battery has power or until the ignition key is removed. • Unlocks the doors automatically. If A Deployment Occurs The airbag systems are designed to deploy when the Occupant Restraint Controller (ORC) detect a moderate- to-severe collision, to help restrain the driver, front passenger and rear passengers, and then immediately...
Page 78 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instruc- tions for cleaning. • It is not advisable to drive your vehicle after the airbags have deployed.
Page 79 WARNING! Do not attempt to modify any part of your advanced airbag system. The airbag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any advanced airbag system service. If your seat, includ- ing your trim cover and cushion, needs to be serviced in any way (including removal or loosening/ tightening of seat attachment bolts), take the vehicle...
Page 80: Event Data Recorder (Edr)
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE located on the inside of the fuse block cover for the proper airbag fuses. See your authorized dealer if the fuse is good. Event Data Recorder (EDR) In the event of an accident, your vehicle is designed to record up to approximately five seconds of specific vehicle data parameters (see the following list) in an event data recorder prior to the moment of airbag de-...
Page 81 accessing the electronic data stored, unless ordered to download data by a court with legal jurisdiction (i.e., pursuant to a warrant). A copy of the data will be provided to the custodial entity upon request. General data that does not identify particular vehicles or crashes may be released for incorporation in aggregate crash databases, such as those maintained by the U.S.
Page 82: Integrated Child Seat - If Equipped
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Engine control status (including engine speed) • Transmission gear selection • Cruise control status • Traction/stability control status • Tire pressure monitoring system status – if equipped Integrated Child Seat — If Equipped Operating instructions for the second row bench seat with Integrated Child Seat are included with the seat.
Page 83: Child Restraints
Child Restraints Everyone in your vehicle needs to be buckled up at all times — babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it.
Page 84 82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Safety experts recommend rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types of child restraints can be used rearward-facing: infant carriers and convertible child seats.
Page 85 Older Children and Child Restraints Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who weigh 20 to 40 lbs (9 to 18 kg) and who are older than one year.
Page 86 84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. If this doesn’t help, move the child to the center rear seating position and use the lap belt.
Page 87 Here are some tips on getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. We also recommend that you make sure that you can install the child restraint in the vehicle where you will use it, before you buy it.
Page 88 86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Buckle the child into the seat according to the child restraint manufacturer’s directions. • When your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle. Don’t leave it loose in the vehicle.
Page 89 Rear Seat Tether Strap Mounting When using the tether anchorages in the center position on third row fold-in-floor seating, ensure that the strap is routed underneath the top of the seatback and the head restraint. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the...
Page 90 88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Because the lower anchorages are to be introduced to passenger carrying vehicles over a period of years, child restraint systems having attachments for those anchor- ages will continue to have features for installation in vehicles using the lap or lap/shoulder belt.
Page 91: Rear Seat Delete Feature (Commercial Vehicles Only) - If Equipped
Not all child restraint systems will be installed as we have described here. Again, carefully follow the instruc- tions that come with the child restraint system. WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint.
Page 92: Restraining Infants And Small Children With Seat
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Commercial Child Restraint Tether Anchor This vehicle is equipped with a child restraint tether anchor located on the lower rear of the front passenger seat. Use this tether anchor to secure only forward facing child restraints equipped with an upper tether strap.
Page 93 VEHICLE EQUIPPED WITH THE REAR SEAT DE- LETE FEATURE (Commercial Vehicles Only). • The forward-facing child seat is for children from about 20 to 40 lbs (9 to 18 kg), and more than one year old. • A “convertible” child seat, one that is designed to be used for children who are too heavy for a rearward- facing infant seat, may be used IN THE FORWARD FACING POSITION ONLY, IT MUST NEVER BE...
Page 94 92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Ensure that the child restraint tether strap is centered between the headrest supports underneath the head rest. 4. Using the hook attached to the child restraint tether strap, attach the child restraint tether strap to the metal anchor on the lower rear of the front passenger seat.
Page 95: Vehicle
ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine in your vehicle. Drive moderately during the first 300 mi (500 km). After the initial 60 mi (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.
Page 96: Periodic Safety Checks You Should Make Outside The Vehicle
94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Light The light should come on and remain on for four seconds as a bulb check when the ignition switch is first turned ON. If the LED is not lit during starting and/or the light stays on or comes ON while driving, have the system checked by an authorized dealer.
Page 97 Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO) follow the safety tips below. Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
Page 99: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors ......100 Manual Rear View Day/Night Mirror — If Equipped .
Page 100 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Setting Memory Positions And Linking RKE Transmitter To Memory ....156 To Open And Close The Hood ... . . 158 Hood Safety Switch —...
Page 101 Power Inverter — If Equipped ... . 196 Electrical Outlet Use With Engine Off ..198 Sun Screens— If Equipped ....198 Cup Holders And Convenience Tray Drawer .
Page 102: Mirrors
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Manual Rear View Day/Night Mirror — If Equipped Adjust the mirror to center on the view through the rear window. A two point pivot system allows for horizontal and vertical adjustment of the mirror. Manual Rearview Mirror Annoying headlight glare can be reduced by moving the small control under the mirror to the night position...
Page 103 Automatic Dimming Mirror UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Illuminated Vanity Mirrors —...
Page 104: Exterior Mirrors
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE EXTERIOR MIRRORS Side View Mirrors To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. WARNING! Vehicles and other objects seen in a outside convex mirrors will look smaller and farther away than they...
Page 105 Power Folding Mirror Switch Both mirrors will always move together and will fold anytime the button is pressed. The ignition switch does not have to be in the ON position. Power Remote Side View Mirrors — If Equipped Use the mirror select switch located on the driver’s door trim panel, to adjust the view obtained in the outside UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 mirrors.
Page 106: Hands-Free Communication (Uconnect ) - If Equipped
NOTE: The UConnect system requires a cellular phone equipped with the Bluetooth Hands-Free Profile, Ver- sion 0.96 or higher. See the UConnect supported phones. NOTE: For UConnect customer support, visit the following websites: • www.chrysler.com/uconnect • www.dodge.com/uconnect • www.jeep.com/uconnect • or call 1–877–855–8400 website for...
Page 107 UConnect allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle and enables you to mute the system’s microphone for private conversation. The UConnect phonebook enables you to store up to 32 names, with four numbers per name.
Page 108: Operation
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect system can be used with any Hands-Free Profile certified Bluetooth cellular phone. See the UConnect website for supported phones. If your cellu- lar phone supports a different profile (e.g., Headset Profile) you may not be able to use any UConnect features.
Page 109 example, you can use the combined form voice com- mand Phonebook New Entry, or you can break the combined form command into two voice commands: Phonebook and New Entry. Please remember, the UConnect system works best when you talk in a normal conversational tone, as if speaking to someone sitting a few feet/meters away from you.
Page 110 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, after the beep, say Pair a Phone and follow the audible prompts. • You will be asked to say a four-digit Personal Identi- fication Number (PIN), which you will later need to enter into your cellular phone.
Page 111 user from dialing an invalid combination of numbers. For example, in the U.S., 234-567-890 is nine digits long, which is not a valid U.S. phone number - the closest valid phone number has 10 digits. • The UConnect system will confirm the phone num- ber and then dial.
Page 112 110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, say the name of the new entry. Use of long names helps the voice recognition and it is recommended. For example, say Robert Smith or Robert instead of Bob. • When prompted, enter the number designation (e.g., Home, Work, Mobile, or Pager ).
Page 113 and you may see a message on the phone display that the Bluetooth link is busy. In this case, the user must first disconnect or drop the Bluetooth connection to the UConnect system, and then send the address book entry via Bluetooth . Please see your phone Owner’s Manual for specific instructions on how to drop the Bluetooth connection.
Page 114 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Delete Entries in the UConnect Phonebook NOTE: Editing phonebook entries is recommended when the vehicle is not in motion. • Press the PHONE button to begin. • After the Ready prompt and the following beep, say Phonebook Delete.
Page 115: Phone Call Features
List All Names in the UConnect Phonebook • Press the PHONE button to begin. • After the Ready prompt and the following beep, say Phonebook List Names. • The UConnect system will play the names of all the phonebook entries. •...
Page 116 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your cell phone.
Page 117 Three-Way Calling To initiate three-way calling, press the “Voice Recogni- tion” button while a call is in progress, and make a second phone call, as described under Making a Second Call While Current Call in Progress. After the second call has established, press and hold the PHONE button until you hear a double beep, indicating that the two calls have been joined into one conference call.
Page 118: Uconnect System Features
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the ignition key is switched to OFF, a call can continue on the UConnect system for a certain dura- tion, after which the call is automatically transferred from the UConnect system to the mobile phone. •...
Page 119 • After the Ready prompt and the following beep, say Emergency and the UConnect system will instruct the paired cellular phone to call the emergency num- ber. This feature is supported in the U.S., Canada, and Mexico. NOTE: The emergency number dialed is based on the country where the vehicle is purchased (911 for the U.S.
Page 120 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE certain companies, which time out a little too soon to work properly with the UConnect system. Voice Mail Calling To learn how to access your voice mail, refer to Working with Automated Systems. Working with Automated Systems This method is used in instances where one generally has to press numbers on the cellular phone keypad while...
Page 121 NOTE: • You may not hear all of the tones due to cellular phone network configurations; this is normal. • Some paging and voice mail systems have system time out settings that are too short and may not allow the use of this feature.
Page 122: Advanced Phone Connectivity
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE dialing a number with your paired Bluetooth cellular phone, the audio will be played through your vehicle’s audio system. The UConnect system will work the same as if you dial the number using voice recognition. NOTE: Certain brands of mobile phones do not send the dial ring to the UConnect system to play it on the vehicle audio system, so you will not hear it.
Page 123 Connect or Disconnect Link Between the UConnect System and Cellular Phone Your cellular phone can be paired with many different electronic devices, but can only be actively connected with one electronic device at a time. If you would like to connect or disconnect the Bluetooth connection between a UConnect paired cellular phone and the UConnect system, follow the instructions de- scribed in your cellular phone User’s Manual.
Page 124: Things You Should Know About Your Uconnect System
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The selected phone will be used for the next phone call. If the selected phone is not available, the UConnect system will return to using the highest priority phone present in or near (approximately within 30 ft [9 m]) the vehicle.
Page 125 Repeat the words and phrases when prompted by the UConnect system. For best results, the Voice Training session should be completed when the vehicle is parked with the engine running, all windows closed, and the blower fan switched OFF. This procedure may be repeated with a new user. The system will adapt to the last trained voice only.
Page 126 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When navigating through an automated system such as voice mail, or when sending a page, at the end of speaking the digit string, make sure to say Send. • Storing names in the phonebook when the vehicle is not in motion is recommended.
Page 127 • Echo at the far end can sometimes be reduced by lowering the in-vehicle audio volume. • In a convertible vehicle, system performance may be compromised with the convertible top down. Bluetooth Communication Link Cellular phones have been found to lose connection to the UConnect system.
Page 128 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 129 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127...
Page 130 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 131 Voice Commands Primary Alternate(s) zero three four five seven eight nine star (*) plus (+) pound (#) add location UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Voice Commands Primary Alternate(s) call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol...
Page 132 130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Primary Alternate(s) language list names list phones mobile mute mute off new entry pager pair a phone phone pairing pairing phonebook phone book previous record again redial Voice Commands Primary Alternate(s) return to main menu return or main menu select phone...
Page 133: General Information
General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired op- eration.
Page 134: Manual Front And Second Row Seat Adjuster
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Front And Second Row Seat Adjuster The adjusting bar is located under the front of the seat. Pull the bar up and move the seat to the desired position. Release the bar to lock the seat into position. Manual Seat Adjuster Using body pressure, move forward and rearward on the seat to be sure the seat adjusters have latched.
Page 135 8–Way Driver’s Power Seat — If Equipped The driver’s power seat switches are located on the outboard side of the seat. The front switch controls up/down, forward/rearward, and tilt adjustment. The rear switch controls the seatback recline adjustment. Driver Power Seat Switch 1 - Bottom Control 2 - Seatback Control UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133...
Page 136 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Pull up or push down on the head restraint cushion so that the upper edge is as high as practical.
Page 137 Heated Seats — If Equipped This feature heats the front driver and passenger seats. The controls for front heated seats are located on the center instrument panel area. The switch in- dicator lights will show when the HIGH or LOW heat is ON. Press the switch once to choose HIGH (two lights), press it a second time to choose LOW (one light), press it a third time for No Heat (no lights).
Page 138 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater.
Page 139 WARNING! DO NOT ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or fatally injured. Use the recliner only when the vehicle is parked.
Page 140: Stow 'N Go Seating - If Equipped
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Stow ’n Go Seating — If Equipped On vehicles equipped with Stow ’n Go seating, the second and third row seats may be folded into the floor for convenient storage. To Fold Second Row Seats 1.
Page 141 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 4. Pull up on the seatback recliner lever located on the outboard side of the seat and fold the seatback down. To assure the seatback is latched in the folded position, additional downward pressure on the seatback may be required when folding.
Page 142 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Pull rearward on the release strap located at the rear of the seat and tumble the seat forward into the storage bin. Second Row Seat Release Strap 6. Close the storage bin cover and slide the storage bin locking mechanism to the locked position.
Page 143 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 To Unfold Second Row Seats 1. Slide the storage bin locking mechanism to the un- locked position and then pull up on the storage bin latch to open the cover. 2. Pull up on the handle to lift the seat out of the storage bin and push the seat rearward to latch the seat anchors.
Page 144 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Pull up on the seatback recliner lever located on the outboard side of the seat, to return the seatback to its full upright position. Second Row Seatback Release Lever 4. Close the storage bin cover and adjust the head restraint to the desired position.
Page 145 The power recline feature, located on the side of the seat cushion, adjusts the seatback angle forward/rearward for occupant comfort Third Row Power Seat Switch UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Remote Third Row Power Seat Switch— If Equipped A One-Touch Third Row Power Folding Seat switch is located in the left rear trim panel as part of a switch-bank.
Page 146 144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The rear switch bank allows multiple power folding and unfolding positions for the third row seats. Left and right third row seats can be folded individually or together. The One Touch Third Row Power Folding Seat adjusts to the following positions using the switch bank located on the left rear trim panel: Rear Panel Power Switch Bank...
Page 147 NOTE: The Third Row Power Seat system includes obstacle detection for safe operation. When the system detects an obstacle, the motors will stop and reverse the motion for a brief period. Should this occur, remove the obstacle and repress the button again, for the desired position.
Page 148 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Unfold Third Row Seats 1. Pull up on the assist strap to lift the seat out of the storage bin and push the seat forward until the anchors latch. 2. Pull release strap marked “1” to unlock the recliner. 3.
Page 149 WARNING! To avoid serious injury or death, NEVER operate the vehicle with occupants in the third row seat while in the tailgate mode. Easy Access Seating The second row Stow ’n Go seats can be tilted forward for easy access to the third row seat or rear cargo area. To tilt the seat, pull forward on the release strap located on the front of the seat between the seatback and seat cushion and tilt the seat fully forward.
Page 150: Swivel 'N Go Premium Seating - If Equipped
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Swivel ’n Go Premium Seating — If Equipped Premium second row Swivel ’n Go Seating features include: • A table that installs between the second and third row seats. The table disassembles and stows in the hidden second row floor storage bin •...
Page 151 To swivel the seat: Pull the lower handle on the outboard side of the seat and push the side of the seatback to begin rotation. Once the seat begins to rotate, the handle may be released. The seat locks in position once reaching the forward or rearward positions only.
Page 152 150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Removing Swivel ’n Go Premium Seating — If Equipped 1. Remove any obstructions from the floor behind the seat, and stow the Third Row Seat. 2. Pull up on the release bar located at the bottom front edge of the swivel seat.
Page 153 Swivel ’n Go Premium Seating Table — If Equipped The Swivel ’n Go Seating Table consists of an easily assembled post and top. Second Row Seating and Table UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 The table and leg are stored beneath the floor when not in use.
Page 154 152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Open the floor storage cover in front of the second row seats. Table and Leg Storage 3. Remove the pole and table top by loosening the hook and loop straps. 4. Insert pole into base by aligning the lock button into notch of the base.
Page 155 5. Twist the pole in a clockwise rotation until it stops. Note: You will hear an audible “click” when the lock button engages the base. 6. Place the table top over the installed pole aligning with the mating feature of the underside of the table top. Apply pressure on the table top and press downward.
Page 156 154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To separate the table top from the pole, follow these steps: 1. Locate the release latch on the underside of the table top. Table Top Release 2. Pull horizontally on the latch to activate the release from the pole.
Page 157: Driver Memory Seat - If Equipped
Plastic Grocery Bag Retainer Hooks Retainer hooks which will hold plastic grocery bag handles are built into the seatbacks of all rear seats and some front seats. The floor supports the partial weight of the bagged goods. DRIVER MEMORY SEAT — IF EQUIPPED Once programmed, the Memory Buttons 1 and 2 on the driver’s door panel can be used to recall the driver’s seat, driver’s outside mirror, adjustable brake and accelerator...
Page 158: Setting Memory Positions And Linking Rke Transmitter To Memory
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Setting Memory Positions And Linking RKE Transmitter To Memory NOTE: Each time the SET(S) button and a numbered button (1 or 2) are pressed, you erase the memory settings for that button and store a new one. 1.
Page 159 10. Insert the ignition key and turn the ignition switch to the ON position. 11. Select Remote Linked to Memory in the Electronic Vehicle Information Center (EVIC) and enter Yes or select No from the EVIC and enter Yes . Refer to the Customer Programmable features in the Electronic Ve- hicle Information Center (EVIC) section for more infor- mation.
Page 160: To Open And Close The Hood
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Press and release Memory Button 1. The system will recall any memory settings stored in position 1. Wait for the system to complete the memory recall before continu- ing to step 3. 3.
Page 161: Hood Safety Switch - If Equipped
Hood Safety Catch Use the hood prop rod to secure the hood in the open position. To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately 12 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 inches (30 cm) and then drop it.
Page 162: Lights
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the vehicle is equipped with the Compass Mini-Trip Computer (CMTC) and the hood is not latched, a “hood” will be displayed in the PRNDL/Odometer window of the instrument cluster. LIGHTS All of the lights, except the hazard warning lights, headlamp high beams and flash to pass, are controlled by switches to the left of the steering column on the instru- ment panel.
Page 163 The interior lights will automatically turn off in about 10 minutes for the first activation and 90 seconds every activation thereafter until the engine is started, if one of the following occur: • A door, sliding door or the liftgate is left open •...
Page 164: Exterior Lights
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Parade Mode (Daytime Brightness Feature) Rotate the dimmer control to the first detent. This feature brightens the odometer, radio and overhead dis- plays when the park lights or head- lights are on. Dimmer Control With the park lights or headlights on, rotating the dimmer control for the interior lights on the instrument panel...
Page 165 Daytime Running Lights (Canada/Fleet Vehicles Only) The headlights on your vehicle will illuminate when the engine is started and the transmission is in any gear except PARK. This provides a constant lights on condi- tion until the ignition is turned OFF. The lights illuminate at less than 50% of normal intensity.
Page 166 164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Headlights NOTE: The engine must be running before the head- lights will come on in the Automatic mode. Headlights On with Wipers — If Equipped If your vehicle is equipped with Automatic Headlights it also has this customer programmable feature.
Page 167 If the headlights are turned off before the ignition, they will turn off in the normal manner. NOTE: The headlights must be turned off within 45 seconds of turning the ignition OFF to activate this feature. Front Fog Lights — If Equipped To activate the front fog lights, turn on the park lights or the low beam headlights and push in the headlight switch control knob.
Page 168: Multifunction Lever
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Battery Protection This feature provides battery protection to avoid wearing down the battery if the headlights, park lights, or front fog lights are left on for extended periods of time when the ignition switch is in the LOCK position. After eight minutes of the ignition switch being in the LOCK posi- tion and the headlight switch in any position other than OFF or AUTO, the lights will turn off automatically until...
Page 169 If either indicator flashes at a rapid rate, check for a defective outside turn signal light bulb. If one of the indicators fails to light when the lever is moved, it would suggest that the indicator light is defective. You may manually signal a lane change by moving the lever partially up or down.
Page 170 168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Wiper and Washer Functions The wipers and washers are operated by a switch within the multifunction lever. Rotate the end of the lever to select the desired wiper speed. NOTE: Always remove any buildup of snow that pre- vents the windshield wiper blades from returning to the off position.
Page 171 1. Multifunction Lever — Mist, Front Wiper and Washer Press the end of the multifunction lever inward to the first detent and release to clear the windshield. Pressing the multifunction lever inward to the second detent will cause the washers to spray for a maximum of 10 seconds, or until the lever is released, and the wipers will cycle three times.
Page 172 170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the rotary ring fully forward and the washers will spray until the ring is released, and then resume the intermit- tent interval. NOTE: Rear window wipers function in the intermittent wiper speed only. 4.
Page 173: Tilt Steering Column - If Equipped
TILT STEERING COLUMN — IF EQUIPPED To tilt the column, pull the small lever downward (located on the steering column and below the steering wheel) to the open position. You may then position the steering wheel up or down, as desired. Pull the small lever upward to the closed position to lock the steering wheel firmly in place.
Page 174: Rear Park Assist Sensors
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Rear Park Assist System will remember the last system state (enabled or disabled) from the last ignition cycle when the ignition is changed to the RUN/ON position. The Rear Park Assist System can be active only when the transaxle gear selector lever is in REVERSE.
Page 175 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 When the ignition switch is turned to the RUN/ON position, the warning display will turn on all of its LEDs for about one second. Each side of the warning display has six yellow and two red LED lights, one set to warn of obstacles behind the left rear of the vehicle and the other set to warn of obstacles behind the right rear of the vehicle.
Page 176 174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE PARK ASSIST WARNING DISPLAY DISTANCES DISPLAY LED OBSTACLE DISTANCE FROM: REAR CORNERS 1st LED 2nd LED 3rd LED 4th LED 31.5 in (80 cm) 5th LED 25.5 in (65 cm) 6th LED 20 in (50 cm) 7th LED 16 in (40 cm) 8th LED...
Page 177 WARNING! Drivers must be careful when backing up even when using the Rear Park Assist System. Always check carefully behind your vehicle, and be sure to check for pedestrians, animals, other vehicles, obstructions, or blind spots before backing up. You are responsible for the safety of your surroundings and must con- tinue to pay attention while backing up.
Page 178 176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • Ensure that the rear bumper is free of dirt and debris to keep the system operating properly. • Jackhammers, large trucks, and other vibrations could affect the performance of the system. Enabling and Disassembling The Rear Park Assist System There are times when you may want to disable the Rear...
Page 179: Adjustable Pedals - If Equipped
If SERVICE PARK ASSIST SYSTEM appears in the Electronic Vehicle Information Center (EVIC), after mak- ing sure the rear bumper is clean, please see your authorized dealer. Should this wrench symbol display with the letter P next to it, your Park Sense System needs servicing.
Page 180 178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the button forward to move the pedals forward (toward the front of the vehicle). Press the button rearward to move the pedals rearward (toward the driver). • The pedals can be adjusted with the ignition OFF. •...
Page 181: Electronic Speed Control - If Equipped
ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over the accelerator operation at speeds greater than 25 mph (40 km/h). Electronic Speed Control Switches UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 Activating Electronic Speed Control Push the ON/OFF button (located in the end of the lever) once and the CRUISE indicator light (located in the message window of the odometer) will illuminate show- ing the electronic speed control system is on.
Page 182 180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Setting Electronic Speed Control at a Desired Speed When the vehicle has reached the desired speed, press the SET lever downward and then release. Lift your foot off the accelerator and the vehicle will operate at the selected speed.
Page 183 NOTE: The Electronic Speed Control system has been designed to shut down if multiple speed control switch functions are operated simultaneously in order to ensure proper operation. If this occurs, the system can be reactivated by pushing the speed control switch ON/ OFF button and resetting the desired vehicle SET speed.
Page 184: Overhead Consoles
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE OVERHEAD CONSOLES Front Overhead Console — If Equipped Two versions of the overhead console are available. The base front overhead console models feature fixed incan- descent courtesy/reading lights, flip-down sunglass stor- age and conversation mirror. Premium front overhead console models feature an LED focused light that illuminates the instrument panel cup holders, Infrared Automatic Temperature Control Sensor...
Page 185 Courtesy/Interior Lighting At the forward end of the console are two courtesy lights (standard dome light has two buttons). The lights turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry, the lights will also turn on when the unlock button on the transmitter is pressed.
Page 186 184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Overhead Consoles — If Equipped The rear overhead storage system is available in two versions: with or without sunroof. An additional LED at the front of the rear console shines down on the second row footwell area while in courtesy mode, for added convenience.
Page 187: Garage Door Opener - If Equipped
Rear Courtesy/Reading Lights — If Equipped The overhead console had two sets of courtesy lights. The lights turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with Remote Keyless Entry, the lights will also turn on when the unlock button on the transmitter is pressed.
Page 188 186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The HomeLink buttons that are located in the headliner or sun visor designate the three different HomeLink channels. HomeLink Buttons NOTE: HomeLink is disabled when the Vehicle Secu- rity Alarm is active. WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver.
Page 189: Programming Homelink
WARNING! Vehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run your vehicle in the garage while training the transceiver. Exhaust gas can cause seri- ous injury or death. PROGRAMMING HOMELINK Before You Begin If you have not trained any of the HomeLink buttons, erase all channels before you begin training.
Page 190 188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Watch for the HomeLink indicator to change flash rates. When it changes, it is programmed. It may take up to 30 seconds, or longer in rare cases. The garage door may open and close while you train. NOTE: Some gate operators and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator/Canadian Programming”...
Page 191 GARAGE DOOR OPENER TRAIN BUTTON 1 — Door Opener 2 — Training Button 6. Firmly press and release the “Learn” or “Training” button. The name and color of the button may vary by manufacturer. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 NOTE: There are 30 seconds in which to initiate the next step after the “Learn”...
Page 192: Gate Operator/Canadian Programming
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using HomeLink To operate, simply press and release the programmed HomeLink button. Activation will now occur for the trained device (i.e., garage door opener, gate operator, security system, entry door lock, home/office lighting, etc.
Page 193: Security
has successfully accepted the frequency signal. The indicator light will flash slowly and then rapidly when fully trained. If you unplugged the device for training, plug it back in at this time. Then proceed with Step 4 under “Programming HomeLink ,” earlier in this section. SECURITY It is advised to erase all channels before you sell or turn in your vehicle.
Page 194: Power Sunroof - If Equipped
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. This device must accept any interference that may be received including interference that may cause undesired operation. NOTE: The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for compli- ance could void the user’s authority to operate the device.
Page 195 Closing the Sunroof Manually To close the sunroof from an open or vent position, press and hold the switch forward. The sunroof will close fully and stop automatically. Release the switch to stop sun- roof travel at any point. Sunroof Sunshade Operation The sunroof sunshade can be opened manually.
Page 196 194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Express-Vent Press and release the V button, and the sunroof will automatically open to the vent position. This is called Express-Vent. Express-Close Press the switch forward and release, and the sunroof will close automatically from any position. The sunroof will close fully, then stop automatically.
Page 197: Electrical Power Outlets - If Equipped
open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.
Page 198 196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE when the overload is removed. The circuit breaker also supplies power to the outlet in the removable floor console, when in the front position. Refer to section 3 “Removable Floor Console” in this manual. A third outlet is located on the driver’s side, just to the rear of the sliding door and is also controlled by the ignition switch.
Page 199 Inverter Outlet Power Switch NOTE: • When the Inverter Switch is pressed, there will be a delay of approximately one second before the inverter status indicator turns ON. The status indicator of the AC power inverter indicates whether the inverter is producing AC power.
Page 200 198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL OUTLET USE WITH ENGINE OFF CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
Page 201 Gently pull up on the tab to raise the sun screen. Continue pulling the sun screen until the tab is near the top of the window. Sun Screen Attaching To Retainer Clips Once the screen is completely to the top of the window, extend the top bar of the sun screen over the two hooks attached to the top of the window.
Page 202 200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUP HOLDERS AND CONVENIENCE TRAY DRAWER There are nine cup holders in the interior. Two cup holders in the center front instrument panel, four in the floor consoles and three more are located in the third row quarter trim panel.
Page 203 Interior Bottle Holders There are four bottle holders located in the interior. One bottle holder is molded into each front interior door trim panels, and one bottle holder is molded into each side sliding interior door trim panel. Each holder accommo- dates up to 20 oz.
Page 204 202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The cup holder/tray top is removable to access a large storage bin. • The Basic Console is removable from the vehicle for additional floor space by removing the cap at the console base. Basic Console Features 1 - Console Anchor 3 - Front Cup holders...
Page 205 • Slide the console base forward while lifting slightly to clear the rear load floor hook. • Remove the console. To Reinstall The Basic Floor Console • Position the console at a slight angle (front slightly higher than the rear. •...
Page 206 204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Top Tray Storage • Upper Storage Bin can hold nine regular or 18 thin CD’s or other items • Large Console Center Storage will store headphones for the available rear DVD entertainment system or other items •...
Page 207 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 The top and center console sections slide forward and rearward to provide added user comfort. Four cup hold- ers, each of which can accommodate large sized beverage containers. A one-piece cup holder insert for both cavities can easily be removed for cleaning.
Page 208 206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Position 2 shows the raised storage tray revealing a large storage area below. Console Position 2 Dual Storage Bins Position 3 shows the top portion of the console in a rearward position. This is accomplished by lifting the upper most latch at the front of the console.
Page 209 Console Position 4 To Remove The Premium Floor Console • Pull up on the bottom release handle in the front of the console • Lift the rear of the console up several inches UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 •...
Page 210 208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched. STORAGE Glove Compartments There are both upper and lower glove compartments. Upper Glove Compartment To open the upper compartment (4), press inward on the release button (3).
Page 211 Lower Glove Compartment To open the lower compartment (1) pull out on the release handle (2). The lower compartment handle is also equipped with a lock. Door Trim Panel Storage Front Door Storage Both interior front door panels have multiple pockets for storage.
Page 212 210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sliding Side Door Bottle Holder Both sliding doors have a bottle holder molded right into the trim. Sliding Door Bottle Holder Second Row Floor Storage Bins — If Equipped The Second Row Seat Storage Bins are located on the floor in front of the second row seats.
Page 213 Pull up on the storage bin latch to open the cover. Slide the storage bin locking mechanism to the unlocked position to allow greater access to the storage bin. CAUTION! The storage bin cover must lay flat and be locked to avoid damage from contact with the front seat tracks, which have minimal clearance to the cover.
Page 214 212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To remove the console use the following procedure: 1. Open the console lid and remove the storage tray. 2. Pull up on the release handle located inside the floor console, and slide the console rearward to disengage from the floor.
Page 215 WARNING! In an accident, serious injury could result if the removable floor console is not properly installed. Always be sure the removable floor console is fully latched. Rear Compartment Storage Your vehicle is equipped with open storage areas located in each rear trim panel. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213 Third Row Rear Seat and Rear Compartment Features 1 —...
Page 216 214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Coat Hooks Coat hooks are located along the headliner for the second and third row seating positions. The coat hook load limit is 10 lbs (4.5 kg). Exceeding the recommended load limit can cause the coat hooks to break or disengage from the vehicle.
Page 217 ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and siderails are designed to carry the weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars. Distribute cargo weight evenly on the roof rack crossbars.
Page 218 216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Crossbars should remain equally spaced or paral- lel at any luggage rack position for proper func- tion. Noncompliance could result in damage to the luggage rack, cargo and/or vehicle. • To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg).
Page 219 WARNING! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in per- sonal injury or property damage. Follow the Roof Rack Cautions when carrying cargo on your roof rack.
Page 220 218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LOAD-LEVELING SYSTEM — IF EQUIPPED The automatic load-leveling system will provide a level riding vehicle under most passenger and cargo loading conditions. A hydraulic pump contained within the shock absorbers raises the rear of the vehicle to the correct height. It takes approximately 1 mile (1.6 km) of driving for the leveling to complete depending on road surface conditions.
Page 221 UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panels And Controls ... . 223 Base Instrument Cluster ....224 Premium Instrument Cluster .
Page 222 220 UNDERSTANDING YOUR INSTRUMENT PANEL Sales Code REQ — AM/FM Stereo Radio And 6–Disc CD/DVD Changer (MP3/WMA AUX Jack) ....252 Operating Instructions - Radio Mode ..252 Operation Instructions - (Disc Mode For CD And MP3/WMA Audio Play, DVD-Video) .
Page 223 Sales Code RER — Multimedia System — If Equipped ......283 Operating Instructions — Satellite Radio ..284 Operating Instructions —...
Page 224 222 UNDERSTANDING YOUR INSTRUMENT PANEL Radio Operation And Cellular Phones ..299 Remote Sound System Controls — If Equipped . . 299 Radio Operation ..... . 299 CD Player .
Page 225: Instrument Panels And Controls
INSTRUMENT PANELS AND CONTROLS 1 - Air Vents 6 - Upper Glove Compartment 2 - Instrument Cluster 7 - Lower Glove Compartment 3 - Gear Selector Lever 8 - Climate Controls 4 - Radio 9 - Storage or DVD 5 - Storage Bin 10 - Cup Holders UNDERSTANDING YOUR INSTRUMENT PANEL 223 11 - Storage Bin...
Page 226: Base Instrument Cluster
224 UNDERSTANDING YOUR INSTRUMENT PANEL BASE INSTRUMENT CLUSTER...
Page 227: Premium Instrument Cluster
UNDERSTANDING YOUR INSTRUMENT PANEL 225 PREMIUM INSTRUMENT CLUSTER...
Page 228: Instrument Cluster Descriptions
226 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position. 2. Fuel Door Reminder The arrow in this symbol is a reminder that the Fuel Filler Door is located on the left side of the vehicle.
Page 229 WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer if your vehicle overheats. If you decide to look under the hood yourself, see Section 7 of this manual. Follow the warnings under the Cooling System Pres- sure Cap paragraph.
Page 230 228 UNDERSTANDING YOUR INSTRUMENT PANEL If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock brakes. If the ABS light does not turn on when the Ignition switch is turned to the ON position, have the light inspected by an authorized dealer.
Page 231 Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS system is required. The operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON position. The light should illuminate for approxi- mately two seconds.
Page 232 230 UNDERSTANDING YOUR INSTRUMENT PANEL replacement, be sure to keep a record of the reading before and after the service so that the correct mileage can be determined. The trip odometer shows individual trip mileage. To switch from odometer to trip odometer, press the Trip Odometer button.
Page 233 seconds after a single chime has sounded to indicate the next scheduled oil change interval. The engine oil change indicator system is duty cycle-based, which means the engine oil change interval may fluctuate dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN position.
Page 234 232 UNDERSTANDING YOUR INSTRUMENT PANEL 15. Malfunction Indicator Light This light is part of an onboard diagnostic system called OBD that monitors engine and automatic transmission control systems. The light will illu- minate when the key is in the ON position before engine start.
Page 235 require towing. The light will come on when the ignition is first turned ON and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer. 18. Oil Pressure Warning Light This light shows low engine oil pressure.
Page 236 234 UNDERSTANDING YOUR INSTRUMENT PANEL during starting, stays on, or turns on while driving, have the system inspected by an authorized dealer as soon as possible. 23. Voltage Light This light monitors the electrical system voltage. The light should turn on momentarily as the engine is started.
Page 237 reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. NOTE: Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsi- bility to maintain correct tire pressure, even if underin- flation has not reached the level to trigger illumination of the TPMS low tire pressure telltale.
Page 238 236 UNDERSTANDING YOUR INSTRUMENT PANEL For additional information on TPMS, refer to Section 5 — Starting and Operating, “Tire Pressure Monitoring Sys- tem” of this manual. For additional information on Tire Pressures, refer to Section 5 — Starting and Operating, “Tire Inflation Pressures”...
Page 239 Electronic Vehicle Information Center (EVIC) Display — If Equipped The Electronic Vehicle Information Center (EVIC) fea- tures a driver-interactive display that is located in the lower half of the speedometer. Oil Change Required Your vehicle is equipped with an engine oil change indicator system.
Page 240: Compass Mini-Trip Computer (Cmtc) - If Equipped
238 UNDERSTANDING YOUR INSTRUMENT PANEL COMPASS MINI-TRIP COMPUTER (CMTC) — IF EQUIPPED NOTE: The compass on your vehicle is self-calibrating, eliminating the need to manually calibrate the compass. The Compass Mini-Trip Computer features a driver- interactive display (displays information on outside tem- perature, compass direction, and trip information).
Page 241 To reset the display shown, turn the ignition switch to the ON position, then press and hold the reset button for approximately two seconds. When the appropriate conditions exist, the following odometer messages will display: NE ..Eight-point compass headings are displayed (N, S, E, W, NE, NW, SE, SW) 14°F.
Page 242: Compass/Temperature Display
240 UNDERSTANDING YOUR INSTRUMENT PANEL Compass/Temperature Display Compass Variance Compass Variance is the difference between magnetic North and Geographic North. In some areas of the country, the difference between magnetic and geographic North is great enough to cause the compass to give false readings.
Page 243: Electronic Vehicle Information Center (Evic) - If Equipped
2. Press and hold (approximately 10 seconds) the CMTC reset button until the current variance zone number is displayed. 3. Release the CMTC reset button, then press and hold again (approximately 10 seconds), until the direction is displayed with the CAL indicator on continuously in the display.
Page 244 242 UNDERSTANDING YOUR INSTRUMENT PANEL • Compass display • Outside temperature display • Trip computer functions • Audio Modes display EVIC Menu / Step Control Button as it appears on the left side of the steering column. Press and release the MENU button and the mode displayed will...
Page 245: Evic Displays
EVIC Displays When the appropriate conditions exist, the EVIC displays the following messages: • Door(s) Ajar (with a single chime if vehicle is in motion) • Liftgate Ajar (chime will sound when vehicle starts moving) • Hood Ajar (If equipped with hood switch) •...
Page 246: Trip Functions
244 UNDERSTANDING YOUR INSTRUMENT PANEL Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN position. To turn off the message temporarily, press and release the Menu button. To reset the oil change indicator system (after performing the scheduled maintenance) refer to the following procedure.
Page 247 Distance To Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level.
Page 248: Compass Display
246 UNDERSTANDING YOUR INSTRUMENT PANEL COMPASS DISPLAY The compass readings indicate the direction the vehicle is facing. Press and release the compass button to display one of eight com- pass readings and the outside temperature. Automatic Compass Calibration This compass is self-calibrating, which eliminates the need to manually reset the compass.
Page 249 UNDERSTANDING YOUR INSTRUMENT PANEL 247 Compass Variance Compass Variance is the difference between magnetic North and Geographic North. In some areas of the country, the difference between magnetic and geographic North is great enough to cause the compass to give false readings.
Page 250: Personal Settings (Customer Programmable Features)
248 UNDERSTANDING YOUR INSTRUMENT PANEL 1. Turn the ignition switch ON. 2. Press and hold the compass button for approximately two seconds. 3. Press the STEP button until “Compass Variance” mes- sage and the last variance zone number displays in the EVIC.
Page 251 Unlock Doors Automatically on Exit When ON is selected, all doors will unlock when the vehicle is stopped and the transmission is in the PARK or NEUTRAL position and the driver’s door is opened. To make your selection, press and release the RESET button until ON or OFF appears.
Page 252 250 UNDERSTANDING YOUR INSTRUMENT PANEL SELECT button until YES (Y) or NO (N) appears. Refer to “Lights/SmartBeams — If Equipped” in Section 3 of this manual for more information. Headlights On with Wipers (Available with Auto Headlights Only) When YES (Y) is selected, and the headlight switch is in the AUTO position, the headlights will turn on approxi- mately 10 seconds after the wipers are turned on.
Page 253: Radio General Information
Rear Park Assist System — If Equipped When ENABLE is selected, the Rear Park Assist System is activated. When DISABLE is selected, the System is deactivated and, the instrument cluster will display the PARK ASSIST DISABLED message. Display Units of Measure in The EVIC, odometer, and navigation system (if equipped) can be changed between English and Metric units of measure.
Page 254: Sales Code Req - Am/Fm Stereo Radio And 6-Disc Cd/Dvd Changer (Mp3/Wma Aux Jack)
252 UNDERSTANDING YOUR INSTRUMENT PANEL FM Reception Because FM transmission is based on frequency varia- tions, interference that consists of amplitude variations can be filtered out, leaving the reception relatively clear, which is the major feature of FM radio. NOTE: The radio, steering wheel radio controls (if equipped), and six-disc CD/DVD changer (if equipped) will remain active for up to 90 seconds after the ignition...
Page 255 When the audio system is turned on, the sound will be set at the same volume level as last played. SEEK Buttons Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down.
Page 256 254 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button Press the TIME button and the time of day will display. In AM or FM mode, pressing the TIME button will switch between the time and frequency displays. Clock Setting Procedure 1. Press and hold the TIME button until the hours blink. 2.
Page 257 Setting the Tone, Balance, and Fade Push the rotary Tune/Scroll control knob and BASS will display. Turn the Tune/Scroll control knob to the right or left to increase or decrease the bass tones. Push the rotary Tune/Scroll control knob a second time and MID will display.
Page 258 256 UNDERSTANDING YOUR INSTRUMENT PANEL Program Type No program type or undefined Adult Hits Classical Classic Rock College Country Foreign Language Information Jazz News Nostalgia Oldies Personality Public 16-Digit Character Display Rhythm and Blues None Adlt Hit Classicl Cls Rock College Country Soft Rhythm and Blues...
Page 259 station with the same selected Music Type name. The Music Type function only operates when in the FM mode. If a preset button is activated while in the Music Type (Program Type) mode, the Music Type mode will be exited and the radio will tune to the preset station. SETUP Button Pressing the SETUP button allows you to select between the following items:...
Page 260 258 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: These selections can only be made while playing a DVD. • VES Power - Allows you to turn VES on and off (if equipped). • VES Lock - Locks out rear VES remote controls (if equipped).
Page 261 Subtitle Language — If Equipped Selecting this item allows you to choose a default subtitle language (effective only if the language is supported by the disc). You can select a language not listed by scrolling down and selecting other. Enter the country code using the Tune/Scroll control knob to scroll up and down to select the number and then push to select.
Page 262: Operation Instructions - (Disc Mode For Cd And Mp3/Wma Audio Play, Dvd-Video)
260 UNDERSTANDING YOUR INSTRUMENT PANEL SET Button — To Set the Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory, press the SET button. The symbol SET 1 will now show in the display window. Select the button (1-6) you wish to lock onto this station and press and release that button.
Page 263 CAUTION! The radio may shut down during extremely hot conditions. When this occurs, the radio will indicate “Disc Hot” and shut off until a safe temperature is reached. This shutdown is necessary to protect the optics of the DVD player and other radio internal components.
Page 264: Notes On Playing Mp3/Wma Files
262 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the EJECT button for five seconds and all CDs will be ejected from the radio. The disc can be ejected with the radio and ignition OFF. SEEK Button (CD MODE) Press the right SEEK button for the next selection on the CD.
Page 265 Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension. When reading discs recorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read files properly and may be unable to play the file nor- mally.
Page 266 264 UNDERSTANDING YOUR INSTRUMENT PANEL When using the MP3/WMA encoder to compress audio data to an MP3/WMA file, the bit rate and sampling frequencies in the following table are supported. In addition, Variable Bit Rates (VBR) are also supported. The majority of MP3/WMA files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rates.
Page 267: List Button (Disc Mode For Mp3/Wma Play)
Loading times for playback of MP3/WMA files may be affected by the following: • Media - CD-RW media may take longer to load than CD-R media • Medium formats - Multisession discs may take longer to load than non-multisession discs •...
Page 268 266 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the INFO button again for three seconds to return to elapsed time display. Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device such as an MP3/WMA player, cassette player, or microphone and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers.
Page 269 Operating Instructions — Voice Recognition System (VR) (If Equipped) For the radio, refer to “Voice Recognition System (VR)” in Section 3. For UConnect “Voice Recognition System (VR)” refer to “Hands-Free Communication (UConnect )” in Section 3. Operating Instructions - Hands-Free Phone (UConnect ) —...
Page 270: Sales Code Res - Am/Fm Stereo Radio With Cd Player (Mp3 Aux Jack)
268 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RES — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of your radio faceplate. RES Radio (Non-Satellite Model Shown - With Satellite Similar) Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
Page 271 to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. SCAN Button Pressing the SCAN button causes the tuner to search for the next listenable station in AM or FM frequencies, pausing for five seconds at each listenable station before continuing to the next.
Page 272 270 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Adjust the hours by turning the right side Tune/Scroll control knob. 3. After adjusting the hours, press the right side Tune/ Scroll control knob to set the minutes. The minutes will begin to blink. 4.
Page 273 Push the rotary Tune/Scroll control knob a second time and MID will display. Turn the Tune/Scroll control knob to the right or left to increase or decrease the mid-range tones. Push the rotary Tune/Scroll control knob a third time and TREBLE will display.
Page 274 272 UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Foreign Language Information Jazz News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues 16-Digit Character Display Language Inform Jazz News Nostalga By pressing the SEEK button when the Music Type icon Oldies is displayed, the radio will be tuned to the next frequency Persnlty...
Page 275 SETUP Button Pressing the SETUP button allows you to select between the following items: • Set Clock — Pressing the SELECT button will allow you to set the clock. Turn the Tune/Scroll control knob to adjust the hours and then press and turn the Tune/Scroll control knob to adjust the minutes.
Page 276: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
274 UNDERSTANDING YOUR INSTRUMENT PANEL DISC Button Pressing the DISC button will allow you to switch from AM/FM modes to Disc modes. Operation Instructions - CD MODE for CD and MP3 Audio Play NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
Page 277 CAUTION! • This CD player will accept 4–3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels. These labels can peel away and jam the player mechanism. •...
Page 278: Notes On Playing Mp3 Files
276 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button Press this button to change the display from a large CD playing time display to a small CD playing time display. RW/FF Press the RW button to stop the CD at the beginning of the current CD track/title.
Page 279 files properly and may be unable to play the file nor- mally. UDF and Apple HFS formats are not supported. The radio uses the following limits for file systems: • Maximum number of folder levels: 8 • Maximum number of files: 255 •...
Page 280 278 UNDERSTANDING YOUR INSTRUMENT PANEL rates (VBR) are also supported. The majority of MP3 files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rates. MPEG Sampling Fre- Specification quency (kHz) MPEG-1 Audio 48, 44.1, 32 Layer 3 MPEG-2 Audio 24, 22.05, 16...
Page 281: List Button (Cd Mode For Mp3 Play)
LIST Button (CD Mode for MP3 Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the Tune/Scroll control knob. Selecting a folder by pressing the Tune/Scroll control knob will begin playing the files contained in that folder (or the next folder in sequence if the selection does not contain playable files).
Page 282: Sales Code Ren - Multimedia System - If Equipped
280 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (Auxiliary Mode) Press this button to change the display to time of day. The time of day will display for five seconds (when ignition is OFF). Operating Instructions - Hands-Free Phone (UConnect ) (If Equipped) Refer to “Hands-Free Communication (UConnect )”...
Page 283: Operating Instructions - Satellite Radio (If Equipped)
through the system’s wireless headphones. This means rear seat passengers can watch a DVD on the optional rear seat entertainment system, while the driver and front-seat passenger listen to the radio. Other special features include direct tune, music type selections, easy store presets, backup camera display for vehicles equipped with a backup camera, and on some models, a dual display screen operation.
Page 284 282 UNDERSTANDING YOUR INSTRUMENT PANEL 3. To move the hour forward, touch the screen where the word “Hour” with the arrow pointing upward is dis- played. To move the hour backward, touch the screen where the word “Hour” with the arrow pointing down- ward is displayed.
Page 285: If Equipped
Touch the screen where the words “Show Time if Radio is Off” are displayed to change the current setting. Changing the Time Zone 1. Turn on the multimedia system. 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3.
Page 286: Operating Instructions - Satellite Radio
284 UNDERSTANDING YOUR INSTRUMENT PANEL The satellite navigation capability combines a Global- Positioning System (GPS)-based navigation system with an integrated color screen to provide maps, turn identi- fication, selection menus, and instructions for selecting a variety of destinations and routes. A shared HDD for the navigation system, the database, and other radio features allows uploads of music and photos from CDs or through the USB port.
Page 287: Clock Setting Procedure
Clock Setting Procedure The GPS receiver in this system is synchronized to the time data being transmitted by the GPS satellites. The satellites’ clock is Greenwich Mean Time (GMT). This is the worldwide standard for time. This makes the sys- tem’s clock very accurate once the appropriate time zone and daylight savings information is set.
Page 288 286 UNDERSTANDING YOUR INSTRUMENT PANEL 3. When this feature is on, a check mark will appear in the box next to the words “Daylight Savings.” Touch the screen where the words “Daylight Savings” are dis- played to change the current setting. Setting the User Clock If you wish to set the clock to a time different from the system clock, you can manually adjust the time by...
Page 289: Satellite Radio - If Equipped (Ren/Req/Rer/Res/Reu Radios Only)
2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. When this feature is on, a check mark will appear in the box next to the words “Show Time if Radio is Off.” Touch the screen where the words “Show Time if Radio is Off”...
Page 290: Selecting Satellite Mode
288 UNDERSTANDING YOUR INSTRUMENT PANEL To access the ESN/SID, refer to the following steps: ESN/SID Access With REQ/RES Radios With the ignition switch in the ON/RUN or ACC posi- tion and the radio on, press the SETUP button and scroll using the Tune/Scroll control knob until Sirius ID is selected.
Page 291: Reception Quality
Reception Quality Satellite reception may be interrupted due to one of the following reasons: • The vehicle is parked in an underground parking structure or under a physical obstacle. • Dense tree coverage may interrupt reception in the form of short audio mutes. •...
Page 292 290 UNDERSTANDING YOUR INSTRUMENT PANEL additional three seconds will make the radio display the Song Title all of the time (press and hold again to return to normal display). INFO Button — REU Radio Pressing the INFO button will display information about Artist, Song Title, and Composer (if available).
Page 293 Pressing the MUSIC TYPE button again will close the MUSIC TYPE screen. Once closed, seek up, seek down, and scan will no longer be based on your selection. SETUP Button Pressing the SETUP button allows you to select the following items: •...
Page 294: Operating Instructions - Hands-Free Phone
292 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Hands-Free Phone (If Equipped) Refer to “Hands-Free Communication (UConnect )” in Section 3. Operating Instructions - Video Entertainment System (VES ) (If Equipped) Refer to separate “Video Entertainment System (VES ) Guide.” UNIVERSAL CONSUMER INTERFACE (UCI) —...
Page 295: Connecting The Ipod Device
Connecting The iPod Device Use the optional connection cable to connect an iPod to the vehicle’s UCI connector (which is located in the glove box or center console on some vehicles. This location may vary with vehicle). Once the iPod is connected and synchronized to the vehicle system (this may take a few seconds to connect), the vehicle brand logo appears on the iPod display, and it starts charging and is ready for...
Page 296 294 UNDERSTANDING YOUR INSTRUMENT PANEL RW (Rewind) Button Press and hold the RW button to move backward in the current track. Holding the RW button long enough will take you back to the beginning of the current track. Pressing and releasing the RW button will go back five seconds of the current track.
Page 297: List Or Browse Mode
SCAN Button Pressing the SCAN button will play the first five seconds of each track in the current list and then forward to the next song. To stop the SCAN mode and start playing the desired track, press the SCAN button again. During the SCAN mode, you can also press the SEEK button to the left or right to go to the previous or next tracks.
Page 298 296 UNDERSTANDING YOUR INSTRUMENT PANEL Radio Preset Buttons In the List mode, the radio preset buttons are used as shortcuts to the following lists on the iPod device. • 1 – Playlists • 2 – Artists • 3 – Albums •...
Page 299: Sirius Backseat Tv™ - If Equipped
SIRIUS BACKSEAT TV™ — IF EQUIPPED Satellite video uses direct satellite receiver broadcasting technology to provide streaming video coast to coast. The subscription service provider is SIRIUS Satellite Radio. SIRIUS Backseat TV™ offers three video channels for family entertainment, directly from its satellites and broadcasting studios.
Page 300 298 UNDERSTANDING YOUR INSTRUMENT PANEL • Nine different medias to choose from in each screen (AM, FM, Sirius Radio, DVD1, DVD2, Hard Drive Jukebox, AUX in radio, AUX1, AUX2). The LCD screen(s) are located in the overhead compart- ment console. Overhead Video Screens VES Remote Control Location NOTE: Refer to your VES User’s Manual for detailed...
Page 301: Radio Operation And Cellular Phones
RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being ON in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
Page 302: Cd Player
300 UNDERSTANDING YOUR INSTRUMENT PANEL CD Player Pressing the top of the switch once will go to the next track on the CD. Pressing the bottom of the switch once will go to the beginning of the current track or to the beginning of the previous track if it is within one second after the current track begins to play.
Page 303: Climate Controls
UNDERSTANDING YOUR INSTRUMENT PANEL 301 CLIMATE CONTROLS The Climate Control System allows you to regulate the temperature, amount, and direction of air circulating throughout the vehicle. The controls are located on the instrument panel, below the radio. MANUAL HEATING, VENTILATION AND AIR CONDITIONING (HVAC) SYSTEM The controls for the manual HVAC system in this vehicle consist of a series of outer rotary dials inner push knobs.
Page 304 302 UNDERSTANDING YOUR INSTRUMENT PANEL Front Blower Control There are four blower speeds. Use this control to regulate the amount of air forced through the system in any mode you select. The blower speed increases as you move the control clockwise from the off position.
Page 305 PANEL Mode Air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow. BI-LEVEL Mode Air is directed through the panel and floor outlets. NOTE: There is a difference in temperature (in any conditions other than full cold or full hot), between the upper and lower outlets for added comfort.
Page 306 304 UNDERSTANDING YOUR INSTRUMENT PANEL RECIRCULATION Control Press this button to choose between outside air intake or recirculation of the air inside the vehicle. A lamp will illu- minate when you are in RE- CIRCULATION mode. Only use the RECIRCULATION mode to temporarily block out any outside odors, smoke, or dust and to cool the inte-...
Page 307 ECONOMY Mode If ECONOMY mode is desired, press the A/C button to turn off the indicator light and the A/C compressor. Rotate the temperature control knob to the desired tem- perature. Air Conditioning Operation Push on this button to engage the Air Conditioning.
Page 308 306 UNDERSTANDING YOUR INSTRUMENT PANEL Three Zone Temperature Control 1 — Left Temp 7 — Right Temp 2 — PANEL 8 — Rear DEFROST 3 — BI-LEVEL 9 — RECIRCULATE 4 — BLOWER 10 — Front DEFROST 5 — FLOOR 11 —...
Page 309: Rear Manual Climate Control Zone - If Equipped
The primary control for the rear blower is on the front climate control unit located on the instrument panel. The front climate control unit has five positions, off, rear, and a range of blower speeds. Only when the primary control for the rear blower is in the REAR position do the second seat occupants have control of the rear blower speed.
Page 310 308 UNDERSTANDING YOUR INSTRUMENT PANEL Only when the front control for the rear blower is in the RR position do the second seat occupants have control of the rear blower speed. The rear blower control, located in the rear overhead console has an off position and a range of blower speeds.
Page 311: Automatic Temperature Control (Atc) - If Equipped
control is in FLOOR, DEFROST, or MIX modes, airflow will be directed out of the rear floor outlets. Rear Mode Control FLOOR Mode Air comes from the floor outlets. BI-LEVEL Mode Air comes from both the headliner outlets and the floor outlets.
Page 312 310 UNDERSTANDING YOUR INSTRUMENT PANEL The Infrared Three-Zone ATC System automatically maintains the interior comfort level desired by the driver and all passengers. This is accomplished by an infrared sensor, located in the forward overhead console. Based on the sensor input, the system automatically adjusts the air temperature, the airflow volume, and amount of outside air recirculation.
Page 313 Below the automatic control, the system selects the appropriate mode (airflow outlets) and fan speed. Front Lower ATC Panel 1 - Blower 4 - Rear HVAC Lock 2 - Rear On/Off 5 - Rear DEFROST 3 - Rear Mode UNDERSTANDING YOUR INSTRUMENT PANEL 311 Operation of the system is quite simple.
Page 314 312 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • It is not necessary to move the temperature settings for cold or hot vehicles. The system automatically adjusts the temperature, mode and fan speed to provide comfort as quickly as possible. • The temperature can be displayed in U.S. or Metric by selecting the US/M customer programmable feature.
Page 315 PANEL Mode Air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. Moving the air vanes of the center outlets down, will close off the airflow from the center outlets.
Page 316 314 UNDERSTANDING YOUR INSTRUMENT PANEL The SNOWFLAKE mode or A/C button allows the operator to manually activate or deactivate the air conditioning system. When in SNOWFLAKE mode the ATC display is on, cool, dehumidified air flows through the air outlets. If ECONOMY mode is desired, press the SNOWFLAKE button to turn off the SNOW- FLAKE mode in the ATC display and deactivate the A/C system.
Page 317 The REAR SYSTEM control for the Rear ATC System is on the front ATC control unit located on the instrument panel. Pressing the REAR LOCK button for the Rear ATC System from the front ATC control unit, illuminates a LOCK symbol in the rear display. The rear temperature and air source are controlled from the front ATC control unit.
Page 318 316 UNDERSTANDING YOUR INSTRUMENT PANEL Operation of the rear system is quite simple. 1. Press the REAR LOCK button on the front ATC control unit. This turns off the REAR LOCK icon in the rear temperature knob. 2. Rotate the Rear Blower, Rear Temperature and the Rear Mode Control knobs to suit your comfort needs.
Page 319 CAUTION! Interior air enters the Rear Automatic Temperature Control System through an intake grille located in the passenger side trim panel behind the third seat. The heater outlets are located in the passenger side trim panel just behind the sliding door. Do not block or place objects directly in front of the inlet grille or heater outlets.
Page 320: Summer Operation
318 UNDERSTANDING YOUR INSTRUMENT PANEL HEADLINER Mode Air comes from the outlets in the headliner. Each of these outlets can be individually adjusted to direct the flow of air. Moving the air vanes of the outlets to one side will shut off the airflow. SUMMER OPERATION The engine cooling system in air conditioned vehicles must be protected with a high-quality antifreeze coolant...
Page 321: Outside Air Intake
UNDERSTANDING YOUR INSTRUMENT PANEL 319 OUTSIDE AIR INTAKE OPERATING TIPS Make sure the air intake, located directly in front of the windshield, is free of obstructions such as leaves. Leaves collected in the air intake may reduce airflow and if they enter the plenum they could plug the water drains.
Page 322: A/C Air Filter - If Equipped
320 UNDERSTANDING YOUR INSTRUMENT PANEL A/C AIR FILTER — IF EQUIPPED On vehicles equipped with Automatic Temperature Con- trol (ATC), the climate control system filters out dust and pollen from the air. Refer to Section 7 “Air Conditioning” for filter replacement instructions. ELECTRIC REAR WINDOW DEFROSTER —...
Page 323: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ..... 324 Automatic Transmission ....325 Engine Block Heater —...
Page 324 322 STARTING AND OPERATING Flowing/Rising Water ....346 Tire Safety Information ....348 Tire Markings .
Page 325 Maintenance ......388 Vehicle Loading ......388 Vehicle Certification Label .
Page 326: Starting Procedures
324 STARTING AND OPERATING STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. WARNING! NEVER leave unattended children alone in a vehicle. Leaving children in a vehicle is dangerous for a number of reasons.
Page 327: Automatic Transmission
Automatic Transmission The gear selector lever must be in the NEUTRAL or PARK position before you can start the engine. Depress the brake pedal before shifting into any driving gear. Normal Starting (Above 32°F/0°C) 1. DO NOT depress the accelerator. 2.
Page 328 326 STARTING AND OPERATING If The Engine Fails To Start WARNING! • NEVER pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury.
Page 329: Engine Block Heater - If Equipped
If the engine shows no sign of starting after two 15– second intervals of cranking with the accelerator pedal held to the floor, the “Normal Starting” procedure should be repeated. After Starting The idle speed will automatically decrease as the engine warms up.
Page 330: Automatic Transmission
328 STARTING AND OPERATING AUTOMATIC TRANSMISSION CAUTION! Damage to the transmission may occur if the follow- ing precautions are not observed: • Shift the gear selector lever into PARK only after the vehicle has come to a complete stop. • Do not shift the gear selector lever from RE- VERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed.
Page 331: Four-Speed Or Six-Speed Automatic Transmission
while the ignition switch is in the ON position. Always press the brake pedal first before moving the gear selec- tor lever out of PARK. Automatic Transmission Ignition Interlock System For electrical system malfunctions, there is an override for the interlock system. In order to override this system, remove the cover located to the top right of the gear selector lever in the instrument panel.
Page 332 330 STARTING AND OPERATING the instrument cluster will display transmission gear selection as 6, 5, 4, 3, 2, 1 for six-speed and 4, 3, 2, 1 for four-speed transmissions. Gear Ranges DO NOT race the engine when shifting the gear selector lever from PARK or NEUTRAL positions into another gear range.
Page 333 WARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the gear selector lever into PARK, remove the key from the ignition, and apply the parking brake.
Page 334 332 STARTING AND OPERATING REVERSE Use REVERSE for moving the vehicle rearward. Shift into REVERSE only after the vehicle has come to a complete stop. NEUTRAL Shift the gear selector lever into this gear only after the vehicle has come to a complete stop. The engine may be started in this range.
Page 335 under heavy loading conditions, (i.e., in hilly terrain, traveling into strong head winds or while towing heavy trailers). Under these conditions, using the “3” range will improve performance and extend transmission life by reducing excessive shifting and heat build-up. CAUTION! If the transmission operating temperature exceeds acceptable limits, the vehicle computer will override DRIVE and select “5”...
Page 336: Reset Mode - Electronic Transmission
334 STARTING AND OPERATING Odometer Screen Display Actual Gear(s) 1-2 1-3 1-4 Allowed —Six- Speed Trans- mission Actual Gear(s) 1-2 1-3 1-4 N/A N/A 1–4 Allowed —Four-Speed Transmission NOTE: To select the proper gear position for maximum deceleration (engine braking), simply press and hold the gear selector lever to the left (-).
Page 337: Parking Brake
5. Shift into the desired gear range and resume driving. NOTE: Even if the transmission can be reset, it is recommended that you visit an authorized dealer at your earliest possible convenience. Your authorized dealer has diagnostic equipment to determine if the problem could recur.
Page 338 336 STARTING AND OPERATING before placing the gear selector lever in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the gear selector lever out of PARK. WARNING! • Always fully apply the parking brake when leav- ing your vehicle, or it may roll and cause damage or injury.
Page 339: Brake System
BRAKE SYSTEM Your vehicle is equipped with dual hydraulic brake systems. If either of the two hydraulic systems loses normal capability, the remaining system will still function. However, there will be some loss of overall braking effectiveness. This will be evident by increased pedal travel during application and greater pedal force required to slow or stop the vehicle.
Page 340: Anti-Lock Brake System (Abs)
338 STARTING AND OPERATING ANTI-LOCK BRAKE SYSTEM (ABS) ABS provides increased vehicle stability and brake per- formance under most braking conditions. The system automatically “pumps” the brakes during severe braking conditions to prevent wheel lock-up. ABS is activated during braking under certain road or stopping conditions.
Page 341 WARNING! • The Anti-Lock Brake System cannot prevent acci- dents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents. • The capabilities of an ABS-equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others.
Page 342: Electronic Brake Control Systems
340 STARTING AND OPERATING to the ABS system is required. Consult with your autho- rized dealer service center as soon as possible. ELECTRONIC BRAKE CONTROL SYSTEMS Your vehicle is equipped with an advanced electronic brake control system that includes TCS (Traction Control System), BAS (Brake Assist System) and ESP (Electronic Stability Program).
Page 343 WARNING! • The TCS cannot prevent the natural laws of phys- ics from acting on the vehicle, nor can it increase the traction afforded. • The TCS cannot prevent accidents, including those resulting from excessive speed in turns, or hydro- planing.
Page 344 342 STARTING AND OPERATING WARNING! • BAS (Brake Assist System) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevail- ing road conditions. • BAS cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning.
Page 345 ESP ON This is the normal operating mode for ESP on 2WD vehicles. Whenever the vehicle is started, the ESP system will be in this mode. This mode should be used for most driving situations. ESP should only be turned off for specific reasons as noted below.
Page 346: Power Steering
344 STARTING AND OPERATING Light comes on continuously with the engine running, a malfunction has been detected in either the ESP or the BAS system. If this light remains on after several ignition cycles, and the vehicle has been driven several miles/ kilometers at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed and corrected.
Page 347: Driving On Slippery Surfaces
WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. CAUTION! Prolonged operation of the steering system at the end of the steering wheel travel will increase the steering fluid temperature and it should be avoided when possible.
Page 348: Traction
346 STARTING AND OPERATING TRACTION When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability.
Page 349 Shallow Standing Water Although your vehicle is capable of driving through shallow standing water, consider the following Caution and Warning before doing so. CAUTION! • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle.
Page 350: Tire Safety Information
348 STARTING AND OPERATING WARNING! • Driving through standing water limits your vehi- cle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. • Driving through standing water limits your vehi- cle’s braking capabilities, which increases stop- ping distances.
Page 351 NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards.
Page 352 350 STARTING AND OPERATING Tire Sizing Chart Passenger Car tire size based on U.S. design standards ...blank... Passenger Car tire based on European design standards Light Truck tire based on U.S. design standards Temporary spare tire Overall diameter in inches (in) Section width in millimeters (mm) Aspect Ratio of section height to section width of tire, written in percent (%) 10.5...
Page 353 A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e., tire pressure, vehicle loading, road conditions, and posted speed limits) ...blank...
Page 354 352 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.
Page 355: Tire Loading And Tire Pressure
Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side B-Pillar. Tire Placard Location STARTING AND OPERATING 353 Tire and Loading Information Placard Tire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle...
Page 356 354 STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading Information placard and in the “Vehicle Loading”...
Page 357 amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 = 750, and 1400 – 750 = 650 lbs [295 kg]). 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.
Page 358 356 STARTING AND OPERATING...
Page 359: Tires - General Information
2WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 360 358 STARTING AND OPERATING WARNING! •Unequal tire pressures can cause steering problems. You could lose control of your vehicle. •Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left.
Page 361 Tire Placard Location The pressure should be checked and adjusted as well as inspecting for signs of tire wear or visible damage at least once a month. Use a good quality pocket-type gauge to check tire pressure. DO NOT make a visual judgement when determining proper inflation.
Page 362 360 STARTING AND OPERATING Tire pressures change by approximately 1 psi (7 kPa) per 12 F (7 C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the winter. Example: If garage temperature = 68°F (20°C) and the outside temperature = 32°F (0°C) then the cold tire inflation pressure should be increased by 3 psi (21 kPa), which equals 1 psi (7 kPa) for every 12 F (7 C) for this...
Page 363 Radial-Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Al- ways use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels).
Page 364 362 STARTING AND OPERATING DO NOT install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. DO NOT install more than one compact spare tire/wheel on the vehicle at any given time.
Page 365 WARNING! • Keep the limited use spare tire inflated to the cold tire inflation pressure listed on either your tire placard or limited use spare tire and wheel assem- bly. • Replace (or repair) the original tire at the first opportunity and reinstall it on your vehicle.
Page 366 364 STARTING AND OPERATING Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm).
Page 367 Keep dismounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease, and gasoline. Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure.
Page 368 366 STARTING AND OPERATING WARNING! • NEVER use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle. Using a tire with a smaller load index could result in tire overloading and failure. You could lose control and have an accident.
Page 369: Tire Chains
TIRE CHAINS Use only compact chains, or other traction aids that meet SAE type “Class S” specifications. Chains must be the proper size for the vehicle, as recommended by the chain manufacturer. NOTE: Do not use tire chains on a compact spare tire. STARTING AND OPERATING 367 CAUTION! To avoid damage to your vehicle or tires, observe the following...
Page 370: Snow Tires
368 STARTING AND OPERATING Always use the lower suggested operating speed if both the chain manufacturer and vehicle manufacture suggest a maximum speed. This notice applies to all chain traction devices, including link and cable (radial) chains. SNOW TIRES Some areas of the country require the use of snow tires during Winter.
Page 371: Tire Pressure Monitor System (Tpms)
The suggested rotation method is the “forward-cross” shown in the following diagram. TIRE PRESSURE MONITOR SYSTEM (TPMS) The TPMS will warn the driver of a low tire pressure based on the cold inflation tire pressure requirements found on the tire placard located on the driver’s-side B-pillar.
Page 372 370 STARTING AND OPERATING increased to the recommended cold tire placard pressure in order for the TPMS warning lamp to be turned off. The system will automatically update and the TPMS warning lamp will extinguish once the updated tire pressures have been received.
Page 373: Basic Tpms Without Evic - If Equipped
CAUTION! After inspecting or adjusting the tire pressure always reinstall the valve stem cap. This will prevent mois- ture and dirt from entering the valve stem, which could damage the TPMS SENSOR. NOTE: • The TPMS is not intended to replace normal tire care and maintenance, or to provide warning of a tire failure or condition.
Page 374 372 STARTING AND OPERATING The Basic TPMS consists of the following components: • Receiver Module • Four Wheel Sensors • TPMS Telltale Warning Light The TPMS Telltale Warning Light will illumi- nate in the instrument cluster, and an audible chime will be activated when one or more of the four active road tire pressures are low.
Page 375: Premium Tpms With Evic - If Equipped
NOTE: 1. The compact spare tire (if equipped) does not have a TPMS sensor. Therefore the TPMS will not monitor the pressure in the compact spare tire. 2. If you install the compact spare tire in place of a road tire that has a pressure below the low-pressure warning limit, upon the next ignition key cycle, a chime will sound and the TPMS Telltale Warning Light will turn on.
Page 376 374 STARTING AND OPERATING • Three Trigger Modules (mounted in three of the four wheel wells) • Various TPMS Messages, which display in the Elec- tronic Vehicle Information Center (EVIC), and graph- ics displaying tire pressures • Yellow TPMS Telltale Warning Light TPMS Low Pressure Warnings The TPMS Telltale Warning Light will illuminate in the instrument cluster, and an audible chime will be acti-...
Page 377 Should a low tire condition occur on any of the four active road tire(s), you should stop as soon as possible, and inflate the low tire(s) that is flashing on the graphic display to the vehicle’s recommended cold tire pressure value.
Page 378 376 STARTING AND OPERATING will not be present, and a pressure value will be dis- played instead of dashes. A system fault can occur by any of the following scenarios: 1. Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPMS sensors.
Page 379: Fuel Requirements
5. Once you repair or replace the original road tire, and reinstall it on the vehicle in place of the compact spare, the TPMS will update automatically. In addition, the TPMS Telltale Warning Light will turn off and the graphic in the EVIC will display a new pressure value instead of dashes (- -), as long no tire pressure is below the low pressure warning limit in any of the four active road tires.
Page 380 If you experience these symptoms, try another brand of “regular” gasoline be- fore considering service for the vehicle. Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifica- tions (the World Wide Fuel Charter, WWFC) to define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle.
Page 381 The manufacturer supports the use of reformulated gaso- lines. Properly blended reformulated gasolines will pro- vide excellent performance and durability of engine and fuel system components. Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxy- genates such as 10% ethanol, MTBE, and ETBE. Oxygen- ates are required in some areas of the country during the winter months to reduce carbon monoxide emissions.
Page 382 380 STARTING AND OPERATING It is even more important to look for gasolines without MMT in Canada, because MMT can be used at levels higher than those allowed in the United States. MMT is prohibited in Federal and California reformu- lated gasolines.
Page 383 • The use of fuel additives which are now being sold as octane enhancers is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of the manufacturer.
Page 384: Adding Fuel
382 STARTING AND OPERATING WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Guard against carbon monoxide with proper maintenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnor- mal conditions repaired promptly.
Page 385 CAUTION! Damage to the fuel system or emission control sys- tem could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system and may cause the Malfunction Indicator Light (MIL) to turn on due to fuel vapors escaping from the system.
Page 386: Loose Fuel Filler Cap Message
384 STARTING AND OPERATING WARNING! A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. Loose Fuel Filler Cap Message •...
Page 387: Ethanol Fuel (E-85)
E-85 Fuel Cap CAUTION! Only vehicles with the E-85 Decal and/or fuel filler door label can operate on E-85. STARTING AND OPERATING 385 E-85 Badge ETHANOL FUEL (E-85) E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline.
Page 388: Fuel Requirements
386 STARTING AND OPERATING WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smok- ing materials lit in or near the vehicle when remov- ing the fuel filler tube cap (gas cap) or filling the tank.
Page 389: Selection Of Engine Oil For Flexible Fuel Vehicles (Ffv) E-85 And Gasoline Vehicles
Selection Of Engine Oil For Flexible Fuel Vehicles (FFV) E-85 and Gasoline Vehicles FFV vehicles operated on E85 require specially formulated engine oils. These special requirements are included in Mopar engine oils, and in equivalent oils meeting DaimlerChrysler Specification MS-6395. The manufacturer only recommends engine oils that are API Certified and meet the requirements of Material Standard MS-6395.
Page 390: Maintenance
388 STARTING AND OPERATING Maintenance If you operate the vehicle using E-85 fuel, follow the maintenance schedule section of this manual. CAUTION! Do not use ethanol mixture greater than 85% in your vehicle. It will cause difficulty in cold starting and may affect driveability.
Page 391: Vehicle Certification Label
Vehicle Certification Label Your vehicle has a Vehicle Certification Label attached to the driver’s door pillar. The label contains the following information: • Name of manufacturer • Month and year of manufacture • Gross Vehicle Weight Rating (GVWR) • Gross Axle Weight Rating (GAWR) front •...
Page 392 390 STARTING AND OPERATING Tire Size The tire size on the Vehicle Certification Label represents the actual tire size on your vehicle. Replacement tires must be equal to the load capacity of this tire size. Rim Size This is the rim size that is appropriate for the tire size listed.
Page 393 Loading To load your vehicle properly, first figure out its empty weight, axle by axle and side by side. Store heavier items down low and be sure you distribute their weight as evenly as possible. Stow all loose items securely before driving.
Page 394 392 STARTING AND OPERATING A loaded vehicle is shown in the illustration. Note that neither the GVWR or the GAWR capacities have been exceeded. LOADING TABLE — EXAMPLE ONLY Front Axle Empty Weight 2,140 lbs (971 kg) Load (Driver, 360 lbs passengers, and (163 kg) cargo/luggage)
Page 395: Common Towing Definitions
TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer carefully re- view this information to tow your load as efficiently and safely as possible.
Page 396 394 STARTING AND OPERATING Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR.
Page 397 Weight-Distributing Hitch A weight-distributing system works by applying lever- age through spring (load) bars. They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer’s axle(s). When used in accordance with the manufacturers directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.
Page 398 396 STARTING AND OPERATING Weight Distributing Hitch System Improper Adjustment of Weight Distributing System...
Page 399 Trailer Hitch Classifications Your vehicle may be factory-equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional Trailer Tow Prep Package. See an authorized dealer for package content. The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition.
Page 400 398 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The Trailer Towing Weights Chart provides the maximum trailer weight ratings towable for a given drivetrain. TRAILER TOWING WEIGHTS (MAXIMUM TRAILER WEIGHT RATINGS) GCWR Engine/ (Gross Combined Transaxle Wt. Rating) 7,000 lbs (3 175 kg) 3.3L, 3.8L and 4.0L / Auto-...
Page 401 Trailer and Trailer Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to severely sway side-to-side, which will cause loss of control of the vehicle and trailer.
Page 402 400 STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the Tire and Loading Information placard in the Tire Safety Information Section of this manual for the maximum combined weight of occupants and cargo for your vehicle.
Page 403 WARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.
Page 404 402 STARTING AND OPERATING 4. Trailer tongue weight rating for that trailer hitch. (This requirement may limit the ability to always achieve the 10% to 15% range of trailer tongue weight as a percentage of total trailer weight.) Towing Requirements — Tires •...
Page 405 • Trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs (907 kg). CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity.
Page 406 404 STARTING AND OPERATING Towing Requirements — Trailer Lights and Wiring Whenever you pull a trailer, regardless of the trailer size, stop lights and turn signals on the trailer are required for motoring safety. The Trailer Tow Package may include a four-pin or a seven-pin wiring harness.
Page 407: Towing Tips
Seven-Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. STARTING AND OPERATING 405 Towing Tips — Automatic Transmission The DRIVE gear can be selected when towing. However, if frequent shifting occurs while in DRIVE, move the gear selector lever into third gear (with four-speed transmis- sion) or fifth gear (with six-speed transmission).
Page 408 406 STARTING AND OPERATING NOTE: • Check the automatic transmission fluid level before towing. • The six-speed automatic transmission is sealed and requires an authorized dealer service center to check the transmission fluid. Towing Tips — Electronic Speed Control (If Equipped) •...
Page 409: Recreational Towing (Behind Motorhome, Etc.)
RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) CAUTION! Towing this vehicle behind another vehicle (flat- towing with all four wheels on the ground) IS NOT RECOMMENDED. STARTING AND OPERATING 407 NOTE: If the vehicle requires towing make sure all four wheels are off the ground.
Page 411: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....410 If Your Engine Overheats ....410 Jacking And Tire Changing .
Page 412: Hazard Warning Flasher
410 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The hazard flasher switch is located in the center of the instrument panel below the radio. To engage the Hazard Warning Flashers, depress the switch on the instrument panel. When the Hazard Warn- ing Switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emer- gency.
Page 413 the fan control to High. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If temperature gauge reads “H”, pull over and stop the vehicle.
Page 414: Jacking And Tire Changing
412 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! • Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack.
Page 415: Jack Location
Jack Location The jack, jack handle and winch handle tools are stowed behind the rear left side trim panel in the rear cargo area. Turn the two cover latches to release the cover. WHAT TO DO IN EMERGENCIES 413 Rear Compartment Features 1 - Tie Down 5 - Liftgate Close Switch 2 - Switch Bank...
Page 416 414 WHAT TO DO IN EMERGENCIES Spare Tire Removal For vehicles equipped with Stow ’n Go seating, the spare tire is stowed inside a protective cover located under the center of the vehicle by means of a cable winch mecha- nism.
Page 417 Preparations For Jacking Park the vehicle on a firm level surface, avoid ice or slippery areas, set the parking brake and place the gear selector in PARK. Turn OFF the ignition. • Turn on the Hazard Warning Flasher. • Block both the front and rear of the wheel diagonally oppo- site the jacking position.
Page 418 416 WHAT TO DO IN EMERGENCIES WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle.
Page 419 1. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while the wheel is still on the ground. 2. To remove the compact spare tire/cover assembly, assemble the winch handle extensions to form a “T’ and fit the winch “T”...
Page 420 418 WHAT TO DO IN EMERGENCIES NOTE: If either front tire is flat, it may be necessary to jack up the vehicle to remove the compact spare tire/ cover assembly from under the vehicle. Refer to jack engagement locations in the following steps for proper jack placement.
Page 421 5. There are two jack engagement locations on each side of the vehicle body. These locations are on the sill flange of the vehicle body. WHAT TO DO IN EMERGENCIES 419 NOTE: Rear jack location is between a pair of down- standing tabs on the sill flange of the vehicle body.
Page 422 420 WHAT TO DO IN EMERGENCIES Jack Location...
Page 423 CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in Step 5. 6. Place the wrench on the jack screw and turn to the right until the jack head is properly engaged in the described location.
Page 424 422 WHAT TO DO IN EMERGENCIES 10. Lower the vehicle by turning the jack screw to the left. 11. Finish tightening the lug nuts. Push down on the wrench while tightening for increased leverage. Alternate lug nuts until each nut has been tightened twice. Correct wheel nut tightness is 95 ft lbs (130 N·m).
Page 425 of operation, and after each time a tire is changed, to allow the wheel nuts to become properly set. All nuts should first be firmly seated against the wheel. The nuts should then be tightened to recommended torque. Tighten the nuts to final torque in increments. Progress around the bolt circle, tightening the nut opposite to the nut just previously tightened until final torque is achieved.
Page 426 424 WHAT TO DO IN EMERGENCIES 2. Assemble the winch handle extensions to form the Spare Tire Hook and pull the wheel spacer from under the vehicle. 3. Turn the compact spare tire so that the valve stem is down and place the tire into the spare tire cover assem- bly.
Page 427: Jump-Starting Procedure
CAUTION! For vehicles equipped with Stow ’n Go seating, the Winch Mechanism is designed specifically to stow a COMPACT Spare Tire ONLY. Do not attempt to use the Winch to stow the Full Size ’Flat’ Tire, or any other Full Size Tire. Vehicle damage may result. WHAT TO DO IN EMERGENCIES 425 JUMP-STARTING PROCEDURE WARNING!
Page 428 426 WHAT TO DO IN EMERGENCIES When jump-starting, proceed as follows: 1. Wear eye protection and remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. 2. When a boost is provided by a battery in another vehicle, park that vehicle within booster cable reach and without letting the vehicles touch.
Page 429: Freeing A Stuck Vehicle
6. Start the engine in the vehicle which has the booster battery, let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery. 7. When removing the jumper cables, reverse the above sequence exactly. Be careful of the moving belts and fan. WARNING! Any procedure other than the jump-starting process listed could result in:...
Page 430: Towing A Disabled Vehicle
428 WHAT TO DO IN EMERGENCIES CAUTION! Racing the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damage the tires. Do not spin the wheels above 35 mph (55 km/h). TOWING A DISABLED VEHICLE Towing With The Ignition Key Your vehicle may be towed under the following condi- tions: The gear selector lever must be in NEUTRAL, the...
Page 431 CAUTION! • Do not push or tow this vehicle with another vehicle as damage to the bumper fascia and trans- mission may result. • If the vehicle being towed requires steering, the ignition switch must be in the OFF position, not in the LOCK or ACC positions.
Page 433 MAINTAINING YOUR VEHICLE CONTENTS 3.3L Engine Compartment ....434 3.8L Engine Compartment ....435 4.0L Engine Compartment .
Page 434 432 MAINTAINING YOUR VEHICLE Power Steering — Fluid Check ... . 452 Front Suspension — Ball Joints ... . 453 Steering Shaft Seal .
Page 435 Center High-Mounted Stop Light (CHMSL) . . . 485 License Light ......485 Fluids And Capacities ....486 MAINTAINING YOUR VEHICLE 433 Fluids, Lubricants And Genuine Parts .
Page 436: 3.3L Engine Compartment
434 MAINTAINING YOUR VEHICLE 3.3L ENGINE COMPARTMENT...
Page 437: L Engine Compartment
MAINTAINING YOUR VEHICLE 435 3.8L ENGINE COMPARTMENT...
Page 438: 4.0L Engine Compartment
436 MAINTAINING YOUR VEHICLE 4.0L ENGINE COMPARTMENT...
Page 439: Onboard Diagnostic System - Obd Ii
ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emis- sions well within current government regulations.
Page 440: Loose Fuel Filler Cap Message - Gascap
438 MAINTAINING YOUR VEHICLE Loose Fuel Filler Cap Message — gASCAP Should the “Loose Fuel Filler Cap” or “gASCAP” mes- sage appear, there may be a problem in the evaporative system. Before taking the vehicle into an authorized dealer, check first to see if the fuel filler cap is possibly loose, improperly installed, or damaged.
Page 441 This vehicle has a simple ignition key-actuated test, which you can use prior to going to the test station. To check if this vehicle’s OBD II system is ready, you must do the following: 1. Insert the ignition key into the ignition switch. 2.
Page 442: Replacement Parts
440 MAINTAINING YOUR VEHICLE serviced before going to the I/M station. The I/M station can fail the vehicle because the MIL is on with the engine running. REPLACEMENT PARTS Use of genuine Mopar parts for normal/scheduled maintenance and repairs is highly recommended to en- sure the designed performance.
Page 443: Maintenance Procedures
MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides the maintenance items for which there are fixed maintenance intervals, there are other items that should operate satisfactorily without periodic maintenance. However, if a malfunction of these items does occur, it could adversely affect the engine or vehicle performance.
Page 444 442 MAINTAINING YOUR VEHICLE Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level between the MIN and MAX markings on the dipstick. Adding one quart of oil when the reading is at the MIN mark will result in a MAX reading on these engines.
Page 445 recommends engine oils that are API certified and meet the requirements of DaimlerChrysler Material Standard MS-6395. American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacturer only recommends API Certified engine oils.
Page 446: Engine Oil Filter
444 MAINTAINING YOUR VEHICLE Synthetic Engine Oils You may use synthetic engine oils provided the recom- mended oil quality requirements are met, and the recom- mended maintenance intervals for oil and filter changes are followed. Materials Added to Engine Oil The manufacture strongly recommends against the addi- tion of any additives (other than leak detection dyes) to the engine oil.
Page 447: Drive Belt
DRIVE BELT At the mileage indicated in the maintenance schedule, replace the drive belt with a new drive belt. NOTE: The drive belt must be routed correctly to ensure proper drive function. SPARK PLUGS Spark plugs must fire properly to assure engine perfor- mance and emission control.
Page 448: Catalytic Converter
446 MAINTAINING YOUR VEHICLE CATALYTIC CONVERTER The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage.
Page 449 WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn.
Page 450: Maintenance-Free Battery
448 MAINTAINING YOUR VEHICLE Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.
Page 451 WARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water.
Page 452: Air Conditioner Maintenance
450 MAINTAINING YOUR VEHICLE AIR CONDITIONER MAINTENANCE For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a system performance check.
Page 453 Refrigerant Recovery And Recycling R-134a Air Conditioning Refrigerant is a hydrofluoro- carbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by an authorized dealer or other an authorized service facility using recovery and recycling equipment.
Page 454: Power Steering - Fluid Check
452 MAINTAINING YOUR VEHICLE 4. Disengage the two retaining tabs that secure the filter cover to the HVAC housing and remove the cover. A/C Air Filter Replacement 5. Remove the A/C Air Filter by pulling it straight out of the housing. 6.
Page 455: Front Suspension - Ball Joints
apparent, and/or the system is not functioning as antici- pated. Coordinate inspection efforts through an autho- rized DaimlerChrysler Dealership. WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to ensure accurate fluid level reading. Do not overfill.
Page 456: Drive Shaft Universal Joints
454 MAINTAINING YOUR VEHICLE DRIVE SHAFT UNIVERSAL JOINTS Your vehicle has constant velocity universal joints. Peri- odic lubrication of these joints is not required. However, the joint boots should be inspected for external leakage or damage when other maintenance is performed. If leakage or damage is evident, the universal joint boot and grease should be replaced immediately.
Page 457 Avoid using the wiper blades to remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. Windshield and Rear Window Washers The fluid reservoir for the windshield washers and the rear window washer is shared.
Page 458: Cooling System
456 MAINTAINING YOUR VEHICLE COOLING SYSTEM WARNING! • When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at anytime the ignition switch is in the ON position.
Page 459 drain from the coolant recovery bottle. DO NOT RE- MOVE THE COOLANT PRESSURE CAP WHEN THE COOLING SYSTEM IS HOT. Cooling System — Drain, Flush and Refill The system should be drained, flushed, and refilled at the intervals shown in the “Maintenance Schedule” in Sec- tion 8 of this manual.
Page 460 458 MAINTAINING YOUR VEHICLE Adding Coolant Your vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This coolant can be used up to five years or 102,000 mi (170 000 km) before replacement. To prevent reducing this extended maintenance period, it is important that you use the same coolant throughout the life of your vehicle.
Page 461 WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety pre- caution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system.
Page 462 460 MAINTAINING YOUR VEHICLE When additional coolant is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points To Remember NOTE: When the vehicle is stopped after a few miles (a few kilometers) of operation, you may observe vapor coming from the front of the engine compartment.
Page 463: Hoses And Vacuum/Vapor Harnesses
• Do not change the thermostat for summer or winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory coolant performance, poor gas mileage, and increased emissions. HOSES AND VACUUM/VAPOR HARNESSES Inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage.
Page 464: Brakes
462 MAINTAINING YOUR VEHICLE BRAKES In order to assure brake system performance, all brake system components should be inspected periodically. Suggested service intervals can be found in the Mainte- nance Schedules. WARNING! Riding the brakes can lead to brake failure and possibly an accident.
Page 465 NOTE: Inspection of brake hoses should be performed whenever the brake system is serviced and every engine oil change. Inspect hydraulic brake hoses for surface cracking, scuffing, or worn spots. If there is any evidence of cracking, scuffing, or worn spots, the hose should be replaced immediately! Eventual deterioration of the hose can take place resulting in a possibility of a burst failure.
Page 466: Automatic Transaxle
464 MAINTAINING YOUR VEHICLE WARNING! • Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. • Use of a brake fluid that has a lower initial boiling point than the recommended MOPAR product or a brake fluid that is unidentified as to FMVSS specification may result in sudden brake failure during hard prolonged braking.
Page 467 All six speed transaxles are equipped with a capped dipstick tube, it is sealed and should not be tampered with. Your authorized dealer has the necessary tools to ensure that the fluid level is set properly. Selection of Lubricant It is important that the proper lubricant is used in the transaxle to assure optimum transaxle performance.
Page 468 466 MAINTAINING YOUR VEHICLE Fluid Level Check — 3.3L Engine with Four-Speed Automatic Transaxle — If Equipped The dipstick is located just behind the radiator, lower right side. 4 Speed ATX Diptstick To properly check the automatic transaxle fluid level, the following procedure must be used: 1.
Page 469: Front And Rear Wheel Bearings
If the fluid level indicates low, add sufficient fluid to bring to the proper level. CAUTION! Do not overfill. Dirt and water in the transaxle can cause serious damage. To prevent dirt and water from entering the transaxle after checking or replenishing fluid, make certain that the dipstick cap is reseated properly.
Page 470 468 MAINTAINING YOUR VEHICLE trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle. Outside parking, which exposes your vehicle to airborne contaminants, road surfaces on which the vehicle is operated, extreme hot or cold weather and other extreme conditions will have an adverse effect on paint, metal trim, and under- body protection.
Page 471 • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces. Special Care •...
Page 472 470 MAINTAINING YOUR VEHICLE Wheel and Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome-plated wheels should be cleaned regularly with a mild soap and water to prevent corrosion. To remove heavy soil and/or excessive brake dust, use Mopar Wheel Cleaner (05066247AB) or equivalent or select a nonabrasive, non-acidic cleaner.
Page 473 soaking your leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, solvents, deter- gents, or ammonia-based cleaners to clean your leather upholstery. Application of a leather conditioner is not required to maintain the original condition. WARNING! Do not use volatile solvents for cleaning purposes.
Page 474 472 MAINTAINING YOUR VEHICLE 2. To maintain the high gloss shine, apply a scratch and swirl remover onto a damp cloth and apply to door applique. Rub the applique with a firm pressure then buff lightly with a clean cotton cloth until a high gloss shine is achieved.
Page 475: Cleaning The Instrument Panel Cup Holders
1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye or clean the seatbelts with chemical solvents or abrasive cleaners.
Page 476: Fuses/Totally Integrated Power Module (Tipm)
474 MAINTAINING YOUR VEHICLE Installation Place the liner into the cupholder drawer and press the liner into place so that the retention tabs seat into the corresponding openings in the drawer. FUSES/TOTALLY INTEGRATED POWER MODULE (TIPM) The Totally Integrated Power Module (TIPM) is located in the engine compartment near the battery.
Page 477 FUSES/TIPM Cartridge Mini Cavity Fuse Fuse 40 Amp — Power Folding Seat Green 30 Amp — Power Liftgate Module Pink 40 Amp — Rear Door Module (RR Green Door Node) 25 Amp — Driver Door Node Natural 25 Amp — Passenger Door Node Natural 40 Amp...
Page 478 476 MAINTAINING YOUR VEHICLE FUSES/TIPM Cartridge Mini Cavity Fuse Fuse 20 Amp — Front/Rear Washer Yellow 25 Amp — Sunroof Module Natural — 15 Amp Center High Mounted Blue Stop Light (CHMSL)/ Brake Switch — 20 Amp Trailer Lighting Yellow —...
Page 479 FUSES/TIPM Cartridge Mini Cavity Fuse Fuse — 30 Amp Amplifier (AMP) Green — 20 Amp Ignition Off Draw— Yellow Cabin Compartment Node (IOD-CCN), Wire- less Control Module (WCM), SIREN, Clock Module (CLK MOD), Multi-Function Control Switch (MULTIFCTN — 20 Amp Trailer Tow (Export Yellow Only)
Page 480 478 MAINTAINING YOUR VEHICLE FUSES/TIPM Cartridge Mini Cavity Fuse Fuse — 15 Amp Left Tail/License/Park Blue Lamp (LT-TAIL/LIC/ PRK LMP) — 15 Amp Right Tail/Park/Run Blue Lamp (RT-TAIL/PRK/ RUN LMP) — 25 Amp Auto Shut Down (ASD Natural #1 and #2) —...
Page 481 FUSES/TIPM Cartridge Mini Cavity Fuse Fuse — 10 Amp Occupant Classification Module (OCM) — 15 Amp Rear Wiper Module (RR Blue WIPER MOD), Power Folding Mirror (PWR FOLD MIR) — 20 Amp Back-Up Lamps (B/U Yellow LAMPS) — 10 Amp Occupant Restraint Con- troller (ORC), TT EU- ROPE...
Page 482 480 MAINTAINING YOUR VEHICLE FUSES/TIPM Cartridge Mini Cavity Fuse Fuse — 25 Amp Lock/Unlock Motors Natural (LOCK/UNLOCK MTRS) Description • When installing the Integrated Power Module cover, it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in a electrical system failure.
Page 483: Vehicle Storage
The Heated Mirrors, Lower Instrument Panel Power Outlet and Removable Floor Console, when in the front position are fused with self-resetting fuses that are only serviceable by an authorized dealer. The power seats are fused by a 30 Amp circuit breaker located under the driver’s seat.
Page 484: Bulb Replacement
482 MAINTAINING YOUR VEHICLE NOTE: For lighted switches, see your dealer for replace- ment. All of the interior bulbs are glass wedge base or glass cartridge types. Aluminum base bulbs are not approved and should not be used for replacement. LIGHT BULBS —...
Page 485: Front Park/Turn Signal And Side Marker Lights
5. Connect the wiring connector to bulb and slide red lock tab forward. Front Park/Turn Signal and Side Marker Lights 1. Raise the hood to access the rear of the headlight housing. 2. Twist the turn signal socket and remove from the headlight housing, then pull the bulb out.
Page 486: Rear Tail, Stop, Turn Signal, Side Marker And Backup Lights
484 MAINTAINING YOUR VEHICLE Rear Tail, Stop, Turn Signal, Side Marker and Backup Lights 1. Raise the liftgate. 2. Remove the tail light assembly by removing the two screws from the inboard side. Use a fiber stick or similar tool to gently pry the light on the outboard side to disengage the two ball studs.
Page 487: Center High-Mounted Stop Light (Chmsl)
1 — Stop, Tail, Turn Signal 2 — Backup Bulb bulb combo 3. Twist the socket and remove form the light assembly. 4. Pull the bulb to remove it from the socket. 5. Replace the bulb, reinstall the socket, and reattach the light assembly.
Page 488: Fluids And Capacities
486 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES FLUIDS AND CAPACITIES Fuel (approximate) All Engines Engine Oil with Filter 3.3L and 3.8L (SAE 5W-20 API Certified) 4.0L (SAE 10W-30 API Certified) Cooling System 3.3L, 3.8L and 4.0L (Use Mopar Antifreeze/Coolant Five Year/ 100,000 Mile Formula or equivalent.) Includes heater and coolant recovery bottle filled to MAX level.
Page 489: Fluids, Lubricants And Genuine Parts
FLUIDS, LUBRICANTS AND GENUINE PARTS Engine FLUIDS, LUBRICANTS AND GENUINE PARTS — ENGINE Component Coolant Mopar Antifreeze/Coolant Five Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent Oil – 3.3L, 3.8L Use API Certified SAE 5W-20 engine oil. Refer to your oil filler cap for correct SAE grade, meeting DaimlerChrysler Material Standard MS-6395.
Page 490: Chassis
488 MAINTAINING YOUR VEHICLE Chassis FLUIDS, LUBRICANTS AND GENUINE PARTS — CHASSIS Component Automatic Transmission Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts Mopar ATF+4 Automatic Transmission Fluid Mopar DOT 3 and SAE J1703 should be used or equivalent.
Page 491 MAINTENANCE SCHEDULES CONTENTS Emissions Control System Maintenance ..490 Maintenance Schedule ....490 Required Maintenance Intervals ... 493...
Page 492 490 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type, must be done at the times or mileages specified to ensure the continued proper functioning of the Emissions Con- trol System. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
Page 493 NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicle’s oil if it has been six months since your last oil change even if the oil change indicator message is NOT illuminated.
Page 494 492 MAINTENANCE SCHEDULES • Check the fluid levels of coolant reservoir, brake master cylinder, power steering and transmission and add as needed. • Check all lights and other electrical items for correct operation. At Each Oil Change • Change the engine oil filter. •...
Page 495 Required Maintenance Intervals Maintenance Items Change the engine oil and engine oil filter. Rotate Tires. If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary. Inspect the brake linings, replace if necessary. Replace the air conditioning filter.
Page 496 494 MAINTENANCE SCHEDULES Maintenance Items Change the automatic transmission fluid & filter if using your vehicle for any of the following: police, taxi, fleet or frequent trailer towing. Inspect and replace PCV valve if necessary. † Flush and replace the engine coolant. Replace the ignition cables on 3.3L, 3.8L engines.
Page 497 WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
Page 499: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......499 Prepare For The Appointment .
Page 500 498 IF YOU NEED CONSUMER ASSISTANCE Department Of Transportation Uniform Tire Quality Grades ......505 Treadwear ......505 Traction Grades .
Page 501: Suggestions For Obtaining Service For Your Vehicle
SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty.
Page 502: Chrysler Llc Customer Center
500 IF YOU NEED CONSUMER ASSISTANCE high quality service. The manufacturer’s authorized deal- ers have the facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer’s service manager first.
Page 503: Chrysler Canada Inc. Customer Center
Chrysler Canada Inc. Customer Center P.O. Box 1621 Windsor, Ontario N9A 4H6 Phone: (800) 465–2001 In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P. 05109 Mexico, D. F. In Mexico City: 5081-4568 Outside Mexico City: 1-800-505-1300 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the...
Page 504: Warranty Information (U.s. Vehicles Only)
502 IF YOU NEED CONSUMER ASSISTANCE service contract that is not a manufacturer’s Service Contract, and you require service after the manufactur- er’s New Vehicle Limited Warranty expires, please refer to the contract documents, and contact the person listed in those documents. We appreciate that you have made a major investment when you purchased the vehicle.
Page 505: Mopar Parts
MOPAR PARTS Mopar fluids, lubricants, parts, and accessories are available from an authorized dealer. They will help keep the vehicle operating at its best. REPORTING SAFETY DEFECTS In The 50 United States And Washington, D.C. If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the...
Page 506: Publication Order Forms
504 IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mas- tercard, American Express, and Discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form.
Page 507 Call toll free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Visit us on the Worldwide Web at: • www.techauthority.com DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle.
Page 508 506 IF YOU NEED CONSUMER ASSISTANCE WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory...
Page 509 INDEX...
Page 510 508 INDEX Adding Engine Coolant (Antifreeze) ..458 Adding Fuel ......382 Adding Washer Fluid .
Page 511 Automatic Dimming Mirror ....100 Automatic Door Locks ....34,35 Automatic Headlights .
Page 512 510 INDEX Brakes ......337,462 Brake/Transmission Interlock ....328 Break-In Recommendations, New Vehicle .
Page 513 Coin Holder ......201 Cold Weather Operation ....325 Compact Disc (CD) Maintenance .
Page 514 512 INDEX Digital Video Disc (DVD) Player ..280,283 Dimmer Control ......162 Dimmer Switch, Headlight .
Page 515 Emission Control System Maintenance ..438,490 Engine ......93,434,435,436 Air Cleaner ......445 Block Heater .
Page 516 514 INDEX Flashers Hazard Warning ..... . . 410 Turn Signal ..... 227,483,484 Flash-To-Pass .
Page 517 Requirements ..... . 377,486 System Hoses ......461 Tank Capacity .
Page 518 516 INDEX Passing ......170 Replacing ......482 Time Delay .
Page 519 Key, Sentry (Immobilizer) ....15 Key-In Reminder ......15 Keyless Entry System .
Page 520 518 INDEX License ......485 Lights On Reminder ....165 Low Fuel .
Page 521 Memory Seat ......104,155 Mini-Trip Computer ....238,244 Mirrors .
Page 522 520 INDEX Outside Rearview Mirrors ....100,102 Overdrive ......332 Overhead Console .
Page 523 Pretensioners Seat Belts ......64 Programmable Electronic Features ... . 248 Radial Ply Tires .
Page 524 522 INDEX Safety Checks Outside Vehicle ....94 Safety Defects, Reporting ....503 Safety, Exhaust Gas .
Page 525 Service Engine Soon Light (Malfunction Indicator) . . 232 Service Manuals ......504 Setting the Clock ....254,269,281,285 Settings, Personal .
Page 526 524 INDEX Synthetic Engine Oil ..... . 444 System, Navigation ..... . 283 System, Remote Starting .
Page 527 Tread Wear Indicators ....364 Wheel Nut Torque ..... 422 Tongue Weight/Trailer Weight .
Page 528 526 INDEX UConnect™ (Hands-Free Phone) ..104,283 Uniform Tire Quality Grades ....505 Universal Consumer Interface (UCI) Connector . . . 292 Universal Joints .
Page 529 Windshield Wiper Blades ....454 Windshield Wipers ..... . . 168 Wiper Blade Replacement .
Page 530 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
Page 531 81-226-0819 Fourth Edition Printed in U.S.A.

This manual is also suitable for:

2008 rt caravan

Dodge 2008 Caravan Owner's Manual

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Understanding Your Instrument Panel 251

Understanding Your Instrument Panel 297

Starting and Operating

What to Do in Emergencies

Maintaining Your Vehicle

If You Need Consumer Assistance

Quick Links

Chapters

Related Manuals for Dodge 2008 Caravan

Summary of Contents for Dodge 2008 Caravan