Page 1 Ram Truck 2 0 0 8 O W N E R ’ S M A N U A L...
Page 2 VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents.
Page 3: Introduction
SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 5: Table Of Contents
CONTENTS Introduction ......4 A Message From DaimlerChrysler Corporation . . . 4 How To Use This Manual ....5 Warnings And Cautions .
Page 6: Introduction
4 INTRODUCTION INTRODUCTION This Owner’s Manual has been prepared with the assis- tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully.
Page 7: How To Use This Manual
follow and careful adherence to them will ensure that you take full advantage of the features of this engine. Thank you for choosing the Cummins Turbo Diesel powered truck. HOW TO USE THIS MANUAL Consult the Table of Contents to determine which section contains the information you desire.
Page 8 6 INTRODUCTION...
Page 9: Van Conversions/Campers
WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against op- erating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against proce- dures which could result in damage to your vehicle. If you do not read this entire manual, you may miss important information.
Page 10: Vehicle Identification Number
8 INTRODUCTION VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is found on the left front corner of the instrument panel, visible through the windshield. This number also appears on the Auto- mobile Information Disclosure Label affixed to a window on your vehicle, the vehicle registration and title.
Page 11 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Ignition Key Removal ....12 Locking Doors With The Key .
Page 12 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Keyless Entry — If Equipped ..21 To Unlock The Doors ....22 To Lock The Doors .
Page 13 Driver And Right Front Passenger Supplemental Restraint System (SRS)—Airbags ...48 Event Data Recorder (EDR) ....59 Child Restraint ......61 New Engine Break-In .
Page 14: Things To Know Before Starting Your Vehicle 9
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The authorized dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your authorized dealer.
Page 15 NOTE: If you try to remove the key before you place the shift lever in PARK, the key may become trapped tem- porarily in the ignition cylinder. If this occurs, rotate the key to the right slightly, then remove the key as de- scribed.
Page 16: Locking Doors With The Key
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! An unlocked car is an invitation to thieves. Always remove key from the ignition and lock all doors when leaving the vehicle unattended. Manual Transmission — If Equipped When the steering wheel is in the LOCK position, the steering and ignition systems are locked to provide antitheft protection for your vehicle.
Page 17: Sentry Key
SENTRY KEY The Sentry Key Immobilizer system prevents unautho- rized vehicle operation by disabling the engine. The system does not need to be armed or activated. Operation is automatic, regardless of whether the vehicle is locked or unlocked. The system uses ignition keys that have an embedded electronic chip (transponder) to prevent unauthorized vehicle operation.
Page 18: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Exxon/Mobil Speedpass™, additional Sentry Keys , or any other transponder-equipped components on the same key chain will not cause a key-related (transponder) fault unless the additional part is physi- cally held against the ignition key being used when starting the vehicle.
Page 19: Customer Key Programming
Customer Key Programming If you have two valid Sentry Keys , you can program new Sentry Keys to the system by performing the following procedure: 1. Cut the additional Sentry Key Transponder blank(s) to match the ignition switch lock cylinder key code. 2.
Page 20: General Information
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If a programmed key is lost, see your authorized dealer to have all remaining keys erased from the sys- tem’s memory. This will prevent the lost key from starting your vehicle. The remaining keys must then be reprogrammed.
Page 21: Automatic Transmission Ignition Interlock
NOTE: If you turned the wheel to the right to engage the lock, you must turn the wheel slightly to the right to disengage it. If you turned the wheel to the left to engage the lock, turn the wheel slightly to the left to disengage it. Automatic Transmission Ignition Interlock System This system prevents the key from being removed unless the shift lever is in PARK.
Page 22: To Disarm The System
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE being set. After the alarm is set, the SECURITY light will flash at a slower rate to indicate that the system is armed. NOTE: If the SECURITY light stays on continuously during vehicle operation, have the system checked by an authorized dealer.
Page 23: Things To Know Before Starting Your Vehicle 21
NOTE: • The front courtesy overhead console and door cour- tesy lights do not turn off if the dimmer control is in the interior lights ON position (extreme top position). • The illuminated entry system will not operate if the dimmer control is in the extreme downward position.
Page 24: To Unlock The Doors
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To unlock the doors: Press and release the UNLOCK button on the Remote Keyless Entry (RKE) transmitter once to unlock only the driver’s door or twice to unlock all the doors. When the UNLOCK button is pressed, the illuminated entry will initiate, the parking lights will flash on twice and if installed, the cargo lamp will turn on for 30 seconds.
Page 25: To Lock The Doors
To lock the doors: Press and release the LOCK button on the RKE transmit- ter to lock all doors. If the ignition is OFF when the doors are locked, the parking lights will flash on once and the horn will chirp once. Park Lights Flash Feature Programming Vehicles will be shipped from the assembly plants with the park light flash feature activated.
Page 26: Using The Panic Alarm
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE (Customer Programmable Features)” under “Over- head Console with Electronic Vehicle Information Center (EVIC) – If Equipped” in Section 3. • For vehicles not equipped with the EVIC, perform the following procedure: 1. Perform this operation while standing outside the vehicle.
Page 27: General Information
General Information This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause undesired operation.
Page 28: Door Locks
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Perchlorate Material – special handling may apply, refer to www.dtsc.ca.gov/hazardouswaste/perchlorate. The recommended replacement battery is CR2032 bat- tery. NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board. 1.
Page 29: Power Door Locks - If Equipped
WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors when you drive as well as when you park and leave the vehicle. • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons.
Page 30 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE chime will sound if the key is in the ignition switch and a door is open, as a reminder to remove the key. Automatic Door Locks – If Equipped If this feature is enabled, your door locks will lock automatically when the vehicle’s speed exceeds 15 mph (25 km/h).
Page 31 8. If a chime is not heard, the program mode was canceled before the feature could be disabled. If neces- sary, repeat the above procedure. Auto Unlock On Exit — If Equipped This feature unlocks all of the doors of the vehicle when any door is opened.
Page 32: Child Protection Door Lock
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 7. Repeat the above steps to alternate the availability of this feature. 8. If a chime is not heard, the program mode was canceled before the feature could be changed. If neces- sary, repeat the above procedure.
Page 33 Child Lock Control THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: After setting the child protection door lock system, always test the door from the inside to make certain it is in the desired position.
Page 34: Windows
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOWS Power Windows – If Equipped Power Window Switches The control on the left front door panel has up-down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window control and on the rear doors of Quad Cab and Mega Cab models.
Page 35 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Auto Down (Driver’s Side Only) The driver’s window switch has an Auto Down feature. Press the window switch past the detent, release, and the window will go down automatically. Window Lockout Switch (4-Door Models Only) The window lockout switch on the driver’s door allows you to disable the window control on the other doors.
Page 36: Power Sliding Rear Window - If Equipped
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Sliding Rear Window – If Equipped Power Sliding Rear Window Switch The power sliding rear window switch is located on the instrument panel below the climate controls. Press the right side of the switch to open the glass and the left side of the switch to close the glass.
Page 37: Occupant Restraints
OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, front airbags for both the driver and front passenger and, if equipped, window bags for the driver and passengers seated next to a window.
Page 38: Lap/Shoulder Belts
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/Shoulder Belts All seating positions except the Quad Cab front center seating position have combination lap/shoulder belts.
Page 39 WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much worse.
Page 40 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is extended long enough to fit, insert the latch plate into the buckle until you hear a “click.” 1 — Latch Plate Latch Plate To Buckle...
Page 41 WARNING! • A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increas- ing the possibility of injury.
Page 42 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen.
Page 43 Regular Cab Front Center Three-Point Belt 1. The front center seat belt on the Regular Cab may be disconnected to open up utilization of the storage areas behind the front seats. The black latch plate can be detached from the black keyed seat belt buckle located on the inboard side of the passenger seat.
Page 44 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • If the black latch and black buckle are not prop- erly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in a collision.
Page 45: Adjustable Upper Shoulder Belt Anchorage
In-Use Position WARNING! If the black latch and buckle are not connected when the seat belt is used by an occupant, the seat belt will not restrain you properly. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Adjustable Upper Shoulder Belt Anchorage In the front row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck.
Page 46: Automatic Locking Retractors (Alr) Mode - If Equipped
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position.
Page 47: Center Lap Belts
Center Lap Belts The center seating position for the Quad Cab front seat has a lap belt only. To fasten the lap belt, slide the latch plate into the buckle until you hear a click. To lengthen the lap belt, tilt the latch plate and pull. To remove slack, pull the loose end of the webbing.
Page 48: Enhanced Seat Belt Reminder System (Beltalert )
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Seat Belt Reminder System (BeltAlert ) If the driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced Warning System (BeltAlert ) will alert the driver to buckle the seat belt.
Page 49: Seat Belts And Pregnant Women
The Enhanced Warning System (BeltAlert ) can be reac- tivated by repeating this procedure. NOTE: Although the Enhanced Warning System (BeltAlert ) has been deactivated, the Seat Belt Warning Light will continue to illuminate while the driver’s seat belt remains unbuckled. Seat Belts and Pregnant Women We recommend that pregnant women use seat belts throughout their pregnancies.
Page 50: Driver And Right Front Passenger Supplemental Restraint System (Srs)-Airbags
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver And Right Front Passenger Supplemental Restraint System (SRS)—Airbags This vehicle has airbags for both the driver and right front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the steering wheel.
Page 51 WARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured be- cause the airbags are no longer functional. These protective covers for the airbag cushions are de- signed to open only when the airbags are inflating.
Page 52 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some simple steps you can follow to minimize the risk of harm from a deploying airbag. 1. Children 12 years and under should always ride buckled up in a rear seat in an appropriate child restraint. Infants in rear-facing child restraints should NEVER ride in the front seat of a vehicle with a passenger front airbag, unless the airbag is turned off (2500/3500 Regular Cab...
Page 53 WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
Page 54 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Driver and Front Passenger Seat Belt Pretensioners (if equipped) • Driver Seat Track Position Sensor (if equipped) • Passenger Side Frontal Airbag ON/OFF Switch (2500/ 3500 Regular Cab Vehicles Only) • Passenger Airbag Disable (PAD) Indicator Light (2500/3500 Regular Cab Vehicles Only) How the Airbag System Works •...
Page 55 WARNING! Ignoring the AIRBAG warning light in your instru- ment panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away.
Page 56 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Driver and Passenger Airbag/Inflator Units are located in the center of the steering wheel and the right side of the instrument panel. When the ORC detects a collision requiring the airbags, it signals the inflator units.
Page 57 • The Knee Impact Bolsters help protect the knees of the driver and the front passenger, and positions them for the best interaction with the front airbag. Passenger Airbag On/Off Switch – (2500/3500 Regular Cab Vehicles Only) THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 The passenger front airbag is to be turned off only if the passenger: •...
Page 58 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Whenever an airbag is turned off, even a lap/ shoulder belted passenger may hit their head, neck, or chest on the dashboard (instrument panel) or windshield in a crash. This may result in serious injury or death.
Page 59 If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor.
Page 60 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you.
Page 61: Event Data Recorder (Edr)
• The light remains on or flickers after the six to eight- second interval. • The light flickers or comes on and remains on while driving. NOTE: If the speedometer, tachometer or any engine- related gauges are not working, the airbag control mod- ule may also be disabled.
Page 62 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In the event that an investigation is undertaken by DaimlerChrysler Corporation (regardless of initiative), the company or its designated representative will first obtain permission of the appropriate custodial entity for the vehicle (usually the vehicle owner or lessee) before accessing the electronic data stored, unless ordered to download data by a court with legal jurisdiction (i.e., pursuant to a warrant).
Page 63: Child Restraint
• Airbag deployment level (if applicable) • Impact acceleration and angle • Seat Belt status • Brake status (service and parking brakes) • Accelerator status (including vehicle speed) • Engine control status (including engine speed) • Transmission gear selection • Cruise control status •...
Page 64 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap can become so great that you could not hold the child, no matter how strong you are.
Page 65 unless the airbag is turned off. An airbag deployment could cause severe injury or death to infants in this position. • Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle.
Page 66 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips for getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.
Page 67 around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position. • Buckle the child into the seat according to the child restraint manufacturer’s directions. • When your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle.
Page 68 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: For children riding in the front seat of a Regular Cab model, refer to the “Passenger Airbag ON/OFF Switch” located in this section. Regular Cab Passenger Seat Quad Cab Rear Outboard Seats...
Page 69 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seatback tether anchorage, have been available for some time.
Page 70 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE of reach of children. It is recommended that before installing the child restraint, buckle the seat belt so the seat belt is tucked behind the child restraint and out of reach. If the buckled seat belt interferes with the child restraint installation, instead of tucking the seat belt behind the child restraint, route the seat belt through the child restraint belt path and then buckle it.
Page 71 rearward-facing infant restraints will also be equipped with a tether strap, a hook and means for adjusting the tension in the strap. In general, you will first loosen the adjusters on the lower straps and tether straps so that you can more easily attach the hook or connector to the lower anchorages and tether anchorages.
Page 72 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle.
Page 73 Multiple Child Restraint Installation Sequence - (Quad Cab Rear Seats) 1. Obtain tether straps by raising the head restraints and reaching between the rear glass and rear seat. The tether strap may be retained with an elastic band. Accessibility to the tether strap is greatly improved by raising the seat cushion to the “up”...
Page 74 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Multiple Child Restraints...
Page 75 Tether Anchorage Points at All Three Seating Positions (Mega Cab ) 1. Place the child restraint on the seat and adjust the tether strap so that it will reach over the seatback under the head restraint to the tether anchor directly behind the seat.
Page 76: New Engine Break-In
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Make sure that the child is upright in the seat. • The lap portion should be low on the hips and as snug as possible. • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position.
Page 77: Safety Tips
• Check the coolant and oil levels frequently. • Vary throttle position at highway speeds when carry- ing or towing significant weight. Because of the construction of the Cummins engine, engine run-in is enhanced by loaded operating conditions which allow the engine parts to achieve final finish and fit during the first 6,000 mi (10 000 km).
Page 78: Lock Your Vehicle
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lock Your Vehicle Always remove the key from the ignition and lock all doors when leaving the vehicle unattended, even in your own driveway or garage. Try to park your vehicle in a well-lighted area and never invite theft by leaving ar- ticles of value exposed.
Page 79: Safety Checks You Should Make Inside The Vehicle
Safety Checks You Should Make Inside The Vehicle Heater Defroster Ducts Inspect the heater defroster ducts for proper operation. Check for proper airflow through all defroster ducts. If there are any questions regarding the operation of your heater defroster ducts, have the system checked by an authorized dealer.
Page 80: Safety Checks You Should Make Outside The Vehicle
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Outside The Vehicle Tires Examine tires for tread wear or uneven wear patterns. Check for stones, nails, glass or other objects lodged in the tread. Inspect for tread cuts or sidewall cracks. Check wheel nuts for tightness and tires for proper pressure.
Page 81 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors .......84 Inside Mirror ......84 Automatic Dimming Mirror –...
Page 82 80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Seats ....... . 115 40-20-40 Front Seat .
Page 83 Electronic Speed Control — If Equipped ..139 To Activate ......140 To Set At A Desired Speed .
Page 84 82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pinch Protect Override ....159 Venting Sunroof - Express ....160 Sunshade Operation .
Page 85 Rear Window Features ....173 Electric Rear Window Defroster And Heated Sideview Mirrors — If Equipped ..173 Power Sliding Rear Window —...
Page 86: Mirrors
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Mirror The mirror should be adjusted to center on the view through the rear window. Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle).
Page 87: Automatic Dimming Mirror - If Equipped
Automatic Dimming Mirror – If Equipped This mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will indicate when the dimming feature is activated.
Page 88: Exterior Mirrors Folding Feature
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicles and other objects seen in a right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side convex mirror could cause you to collide with an- other vehicle or other object.
Page 89: Electric Rear Window Defroster And Heated Sideview Mirrors - If Equipped
Power Mirror Switches Set the top switch to the left or right for the left or right mirror, and set it to the center off position to prevent accidentally moving a mirror when you are finished adjusting the mirror. To adjust a mirror, select left or right with the top switch, and press one of the four arrows for the direction you want the mirror to move.
Page 90 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE extra-wide loads. To change position inboard or out- board, the mirror head should be rotated (flipped out or in). A small blindspot mirror is integrated onto the main mirror surface. NOTE: Fold the trailer towing mirrors rearward prior to entering an automated car wash.
Page 91: Hands-Free Communication (Uconnect ) - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 NOTE: For UConnect following websites: • www.chrysler.com/uconnect • www.dodge.com/uconnect • www.jeep.com/uconnect • or call 1–877–855–8400 UConnect allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle and enables you to mute the system’s microphone...
Page 92 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE different electronic devices to connect to each other without wires or a docking station, so UConnect works no matter where you stow your cellular phone (be it your purse, pocket, or briefcase), as long as your phone is turned on and has been paired to the vehicle’s UConnect system.
Page 93: Operation
The radio display will be used for visual prompts from the UConnect system such as CELL or caller ID on certain radios. Operation Voice commands can be used to operate the UConnect system and to navigate through the UConnect menu structure.
Page 94 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To activate the UConnect system from idle, simply press the PHONE button and follow the audible prompts for directions. All UConnect system sessions begin with a press of the PHONE button on the radio control head. Cancel Command At any prompt, after the beep, you can say Cancel and you will be returned to the main menu.
Page 95 • You will then be asked to give your cellular phone a priority level between 1 and 7, with 1 being the highest priority. You can pair up to seven cellular phones to your UConnect system. However, at any given time, only one cellular phone can be in use, connected to your UConnect system.
Page 96 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The system will prompt you to say the name of the person you want to call. • After the Ready prompt and the following beep, say the name of the person you want to call. For example, you can say John Doe, where John Doe is a previ- ously stored name entry in the UConnect phonebook.
Page 97 The UConnect system will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations. Each language has a separate 32-name phonebook accessible only in that language. Phonebook Download UConnect allows the user to download entries from their phone via Bluetooth .
Page 98 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You will then be asked for the name of the phonebook entry that you wish to edit. • Next, choose the number designation (home, work, mobile, or pager) that you wish to edit. •...
Page 99 • After you enter the name, the UConnect system will ask you which designation you wish to delete: home, work, mobile, pager, or all. Say the designation you wish to delete. • Note that only the phonebook entry in the current language is deleted.
Page 100: Phone Call Features
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phone Call Features The following features can be accessed through the UConnect system if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this feature can be accessed through the UConnect your cellular service provider for the features that you have.
Page 101 to Toggling Between Calls in this section. To combine two calls, refer to Conference Call in this section. Place/Retrieve a Call From Hold To put a call on hold, press the PHONE button until you hear a single beep. This indicates that the call is on hold. To bring the call back from hold, press and hold the PHONE button until you hear a single beep.
Page 102: Uconnect System Features
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the Ready prompt and the following beep, say Redial. • The UConnect system will call the last number that was dialed from your cellular phone. NOTE: This may not be the last number dialed from the UConnect system.
Page 103 After selecting one of the languages, all prompts and voice commands will be in that language. NOTE: After every UConnect language change opera- tion, only the language-specific 32-name phonebook is usable. The paired phone name is not language-specific and usable across all languages. Emergency Assistance If you are in an emergency and the mobile phone is reachable:...
Page 104 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Towing Assistance If you need towing assistance: • Press the PHONE button to begin. • After the Ready prompt and the following beep, say Towing Assistance. NOTE: The Towing Assistance number dialed is based on the country where the vehicle is purchased (1-800-528- 2069 for the U.S., 1-877-213-4525 for Canada, 55-14-3454 for Mexico City and 1-800-712-3040 for outside Mexico...
Page 105 sequence on your cellular phone keypad, you can press the “Voice Recognition” button and say the sequence you wish to enter, followed by the word Send. For example, if required to enter your PIN followed with a pound, (3 7 4 6 #), you can press the “Voice Recognition”...
Page 106 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Press the PHONE button to begin. • After the Ready prompt and the following beep, say Setup Confirmations. The UConnect system will play the current confirmation prompt status and you will be given the choice to change it. Phone and Network Status Indicators If available on the radio and/or on a premium display such as the instrument panel cluster, and supported by...
Page 107: Advanced Phone Connectivity
• Following the beep, say Mute. In order to un-mute the UConnect system: • Press the “Voice Recognition” button. • Following the beep, say Mute off. Advanced Phone Connectivity Transfer Call to and from Cellular Phone The UConnect system allows ongoing calls to be trans- ferred from your cellular phone to the UConnect system without terminating the call.
Page 108 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The UConnect system will play the phone names of all paired cellular phones in order from the highest to the lowest priority. To “select” or “delete” a paired phone being announced, press the “Voice Recogni- tion”...
Page 109: Things You Should Know About Your Uconnect System
Things You Should Know About Your UConnect System UConnect Tutorial To hear a brief tutorial of the system features, press the PHONE button and say “UConnect Tutorial.” Voice Training For users experiencing difficulty with the system recog- nizing their voice commands or numbers, the UConnect system Voice Training feature may be used.
Page 110 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Speak normally, without pausing, just as you would speak to a person sitting a few feet/meters away from you. • Make sure that no one other than you is speaking during a voice recognition period. •...
Page 111 • In a convertible vehicle, system performance may be compromised with the convertible top down. Far End Audio Performance • Audio quality is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, •...
Page 112 110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 113 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111...
Page 114 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 115 Voice Commands Primary Alternate(s) zero three four five seven eight nine star (*) plus (+) pound (#) add location UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Voice Commands Primary Alternate(s) call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol...
Page 116 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Primary Alternate(s) language list names list phones mobile mute mute off new entry pager pair a phone phone pairing pairing phonebook phone book previous record again redial Voice Commands Primary Alternate(s) return to main menu return or main menu select phone...
Page 117: General Information
General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired op- eration.
Page 118: 40-20-40 Front Seat
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 40-20-40 Front Seat Manual Seat Adjuster As the name implies, the seat is divided into three segments. The outboard seat portions are each 40% of the total width of the seat. The back of the center portion (20%) easily folds down to provide an armrest/center storage compartment (if equipped).
Page 119: Reclining Seats
Reclining Seats The recliner handle is on the outside of the seat cushion. Pull up on the handle, as shown, to release the seatback and adjust for comfort. Seat Recliner Handle UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 WARNING! You can be seriously, even fatally, injured riding in a seat with the seatback reclined.
Page 120: Adjustable Head Restraints
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjustable Head Restraints Head restraints can reduce the risk of neck injury in the event of impact from the rear. Pull up or push down on the restraints so that the upper edge is as high as practical, at least to the level of the ears.
Page 121: Manual Rotary Lumbar Support Adjustment - If Equipped
Manual Rotary Lumbar Support Adjustment — If Equipped Rotating the lumbar control knob on the left side of the driver’s seatback and on the right side of the passenger’s seatback increases or decreases the lumbar (lower back) support. Manual Lumbar Adjustment UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 Power Seats —...
Page 122 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Up, Down, Forward, and Rearward The power seat controls are on the outboard side of the front seat cushions. Three switches control the seat move- ment. The four-way switch in the center can be moved forward or backwards to get the most comfortable posi- tion.
Page 123: Rear Seat Features - Mega Cab Models
Rear Seat Features — Mega Cab Models Reclining Rear Seats — Mega Cab Models The recliner handle is on the outside of the seat cushion. Pull up on the handle, as shown, to release the seatback and adjust for comfort. Rear Seat Recliner Handle UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Folding Rear Seat (Table Mode) —...
Page 124 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Table Mode Handle Table Mode...
Page 125 Folding Rear Seat (Kneel Mode) — Mega Cab Models Both the left and right rear seats can be folded flat (Kneel Mode) and used for carrying cargo. Each of the rear seatbacks provide two D-rings and each of the rear storage bin lids provide two slotted cutouts.
Page 126 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Cargo must be securely tied down before driving your vehicle. Improperly secured cargo can fly around in a sudden stop and strike someone in the vehicle, causing serious injury or possible death. Secure cargo with a cargo tie down using the D-Rings provided on the back of the seats and the slotted cutouts in the rear storage bin lid.
Page 127 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 WARNING! Be certain that the seatback is securely locked into position. If the seatback in not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury.
Page 128: Heated Seats - If Equipped
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats — If Equipped The heated seat switches are located in the instrument panel under the climate controls. Heated Seat Switches Each heated seat switch has two settings (HI and LOW). Press the switch once to obtain High heat level, then press the switch again to obtain Low heat level.
Page 129: To Open And Close The Hood
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 TO OPEN AND CLOSE THE HOOD WARNING! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater.
Page 130 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To open the hood, two latches must be released. First pull the hood release lever located below the steering wheel at the base of the instrument panel. Once the hood is released you must reach into the opening beneath the center of the grille and push up the latch to release the safety catch before raising the hood.
Page 131: Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 LIGHTS Interior Lights Headlight Switch Location Dimmer Control...
Page 132: Battery Saver
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the switch) is rotated to the upward detent position, or if equipped, when the UN- LOCK button is pressed on the key fob.
Page 133: Headlamp Delay
Headlamp Delay To aid in your exit, your vehicle is equipped with a headlamp delay that will leave the headlamps on for 90 seconds. This delay is initiated when the ignition is turned OFF while the headlamp switch is ON, and then the headlamp switch is cycled OFF.
Page 134: Daytime Running Lights (Canada Only And Fleet Vehicles)
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other abrasive materials to clean the lenses.
Page 135: Cargo Light - If Equipped
Cargo Light — If Equipped Cargo Light Switch The cargo lights are turned ON by pressing on the CARGO button. The interior lights will also turn on when the cargo lights are on. The cargo lights will also turn ON for 30 seconds when a key fob UNLOCK is pressed, as part of the illuminated entry feature.
Page 136 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE You can signal a lane change by moving the lever partially up or down. Turn Signal Lever Turn Signal Auto Mode Tap the multifunction control lever once and the turn signal (left or right) will flash three times, and automati- cally turn off.
Page 137: Windshield Wipers And Washers
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 WINDSHIELD WIPERS AND WASHERS Windshield Wipers High Beam / Low Beam Windshield Wiper / Washer Switch...
Page 138: Windshield Washers
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The wipers and washers are operated by a switch in the multifunction control lever. Turn the end of the handle to select the desired wiper speed. Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable.
Page 139: Tilt Steering Column
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 while in the OFF position, the wiper will wipe approxi- mately three wipes after the wash knob is released. To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate.
Page 140: Driver Adjustable Pedals - If Equipped
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Tilting the steering column while the vehicle is moving is dangerous. Without a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped.
Page 141: Adjustment
Adjustment 1. Position the driver seat so that you are at least 10 in (254 mm) away from the airbag located in the center of the steering wheel. 2. Fasten and adjust the seatbelts. 3. Move the adjustable pedal switch, located to the left of the steering column near the parking brake release, in the direction you desire to move the pedals.
Page 142: To Activate
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The Electronic Speed Control System has been designed to shut down if multiple speed control switch buttons (i.e., SET and CANCEL) are operated simulta- neously, in order to ensure proper operation. The system can be reactivated by pushing the speed control switch ON/OFF button and re-establishing the desired vehicle SET speed.
Page 143: To Resume Speed
To Resume Speed To resume a previously set speed, push and release the RESUME button. Resume can be used at any speed above 30 mph (50 km/h). To Vary The Speed Setting When the speed control is on, speed can be increased by pressing and holding the RESUME/ACCEL button.
Page 144: Overhead Console With Electronic Vehicle Information Center (Evic) - Diesel Only
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Vehicles equipped with a 4–speed automatic transmis- sion may exhibit several 4-3 downshifts under the above conditions. To reduce the frequency of the downshifts and to improve vehicle performance, it is advisable to lock out overdrive by pressing the O/D OFF button located at the end of the gear shifter.
Page 145: Electronic Vehicle Information Center (Evic) - If Equipped
Dome/Reading Lights UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Electronic Vehicle Information Center (EVIC) — If Equipped Overhead Console with EVIC Pressing the menu button will change the display to one of the following features:...
Page 146 144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Trip Functions Pressing the STEP button allows you to scroll through one of the following Trip Function features: • TRIP – Shows the total distance traveled since the last reset. To reset the TRIP function, press and hold the RESET button.
Page 147 will continue until the vehicle runs out of fuel. Adding a significant amount of fuel to the vehicle will turn off the LOW FUEL text and a new DTE value will display. System Status (EVIC Displays) When the appropriate conditions exist, the Electronic Vehicle Information Center (EVIC) displays the following messages: •...
Page 148 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN position.
Page 149 Press and release the Menu button until the Personal Settings displays on the EVIC. Use the STEP button to display one of the following: • “LANGUAGE” – When in this display you may select one of three languages for all display nomenclature, including the trip functions.
Page 150 148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • “SOUND HORN W/LOCK > ON” – When ON is selected, a short horn sound will occur when the remote keyless entry LOCK button is pressed. This feature may be selected with or without the flash lights on lock/unlock feature.
Page 151: Compass/Temperature Button
NOTE: If this feature is enabled, the headlamps will be on during the engine pre-heat and cold crank; therefore, it is recommended that the feature be disabled when overnight ambient temperature is at or below 20°F (-7°C) to prevent excessive drain on batteries during cold crank- ing.
Page 152: 150 Understanding The Features Of Your Vehicle
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Compass Calibration If the compass appears erratic and the “CAL” message does not appear in the EVIC display, you must put the compass into the Calibration Mode manually as follows: 1. Turn the ignition switch to the ON/RUN position. 2.
Page 153: Garage Door Opener - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 1. Turn the ignition switch to the ON/RUN position. 2. Press the Menu button until Personal Settings is displayed. 3. Press the STEP button until “Compass Variance” is displayed. 4. Press and release RESET button until the proper variance zone is selected according to the map.
Page 154 152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The HomeLink buttons are located in the overhead console, and contain one, two, or three dots/lines desig- nating the different HomeLink channels. HomeLink Buttons NOTE: HomeLink is disabled when the Vehicle Secu- rity Alarm is active. WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver.
Page 155: Programming Homelink
WARNING! Vehicle exhaust contains carbon monoxide, a danger- ous gas. Do not run your vehicle in the garage while training the transceiver. Exhaust gas can cause seri- ous injury or death. Programming HomeLink Before You Begin If you have not trained any of the HomeLink buttons, erase all channels before you begin training.
Page 156 154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Then release both the HomeLink and hand-held trans- mitter buttons. If the EVIC display states “DID NOT TRAIN” repeat Step 3. If the signal is too weak, replace the battery in the original hand-held transmitter. It may take up to 30 seconds, or longer, in rare cases.
Page 157: Gate Operator/Canadian Programming
1 — Garage Door Opener 2 — Training Button 6. Firmly press and release the “learn” or “training” button. The name and color of the button may vary by manufacturer. NOTE: There are 30 seconds in which to initiate the next step after the “Learn”...
Page 158: Using Homelink
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner. It may be helpful to unplug the device during the cycling process to prevent possible overheating of the garage door or gate motor.
Page 159: Security
3. Without releasing the button, proceed with Program- ming HomeLink Step 2 and follow all remaining steps. Security It is advised to erase all channels before you sell or turn in your vehicle. To do this, press and hold the two outside buttons for 20 seconds until the EVIC message states “CHANNELS CLEARED.”...
Page 160: Power Sunroof - If Equipped
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for compli- ance could void the user’s authority to operate the device.
Page 161: Open Sunroof - Express Mode
Open Sunroof - Express Mode Momentarily pressing the switch rearward will activate the Express Open Feature, causing the sunroof to open automatically. During the Express Open operation, any movement of the switch will stop the sunroof and it will remain in a partial open position. Again, momentarily pressing the switch rearward will activate the Express Open Feature.
Page 162: Venting Sunroof - Express
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Venting Sunroof - Express Press and release the V button, and the sunroof will open to the vent position. This is called Express Vent, and will occur regardless of sunroof position. During Express Vent operation, any movement of the switch will stop the sunroof.
Page 163 There is an additional power outlet inside the center console of vehicles equipped with 40-20-40, or Bucket front seats. There is also a power outlet located on the rear of the center console for Quad Cab or Mega Cab vehicles (only) equipped with bucket seats. The outlet(s) has/have a fused direct feed from the battery so it/they receive power whether the ignition is ON or OFF.
Page 164: Cigar Lighter And Ash Receiver
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CIGAR LIGHTER AND ASH RECEIVER The removable ash receiver is located in the instrument panel cupholder tray. The cigar lighter is located on the instrument panel, above and to the left of the ash receiver. As a child safety precaution, the lighter only operates with the ignition switch ON.
Page 165: Cupholders
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 CUPHOLDERS Front Instrument Panel Cupholders (40–20–40 Seats) — Automatic Transmission Your new vehicle is equipped with two adjustable cup- holders. The cupholder is opened by pulling on the cup holder door handle located on the front surface. Each opening in the cupholder is adjustable and will hold cups and mugs of various sizes.
Page 166 164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cupholder Door Handle Cupholders Automatic Transmission...
Page 167: Front Instrument Panel Cupholders
Front Instrument Panel Cupholders (Bucket Seats) — Automatic Transmission If your new vehicle is equipped with bucket seats there are three cupholders located on the front of the center console. Cupholders Bucket Seat UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 Front Instrument Panel Cupholders —...
Page 168: Rear Cupholder (Quad Cab ) - If Equipped
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Cupholder (Quad Cab ) — If Equipped Quad Cab vehicles may be equipped with a rear cup- holder that consists of two cup wells for rear passenger convenience. Rear Cupholder (Mega Cab ) Mega Cab vehicles are equipped with rear cupholders located in the center armrest.
Page 169: Storage
STORAGE Center Storage Compartment (40–20–40 Seat) – If Equipped Center Storage Compartment The center portion of the seat folds down to provide an armrest with unique storage compartments under the lid. Push the button on the front of the armrest to raise the UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 cover.
Page 170: Center Storage Compartment (Bucket Seats) - If Equipped
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
Page 171 storage area into separate compartments. Lift the lower handle on the front of the armrest, and raise the armrest for access to the lower storage bin. On Quad Cab and Mega Cab models the rear of the floor console offers a power outlet, a tip out bin and a rear air duct (Mega Cab Only).
Page 172: Storage And Seats (Quad Cab Models)
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage and Seats (Quad Cab Models) Located in the center of the front 40–20–40 seat cushion there is a storage compartment. Regular Cab models also have storage behind the seat. The Quad Cab models provide additional storage under the rear seat.
Page 173: Storage And Seats (Mega Cab Models)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 Storage and Seats (Mega Cab Models) The Mega Cab models provide additional storage behind the rear seat. To gain access to the Mega Cab rear storage, fold the rear seats to the “kneel position”. (See page 123 for more information.) Push down on the front of the storage compartment handle and lift the storage compartment cover.
Page 174: Plastic Grocery Bag Retainers (Mega Cab Models)
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The rear storage compartment can be divided into three separate compartments by using the divider doors inside the storage compartment. Mega Cab Rear Storage Dividers Plastic Grocery Bag Retainers (Mega Cab Models) Retainer hooks which will hold plastic grocery bag handles are built into the back panel of the cab, behind the rear seat.
Page 175: Rear Window Features
REAR WINDOW FEATURES Electric Rear Window Defroster and Heated Sideview Mirrors — If Equipped The Electric Rear Window Defroster and Heated Sideview Mirrors are activated by pressing the heated grid button, located on the Climate Control panel, with the ignition ON. Turning OFF the ignition will deactivate the Electric Rear Window Defroster and Heated Sideview Mirrors feature.
Page 176: Sliding Rear Window - If Equipped
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sliding Rear Window — If Equipped A locking device in the center of the window helps to prevent entry from the rear of the vehicle. Squeeze the lock to release the window. FOLD FLAT LOAD FLOOR — IF EQUIPPED Quad Cab models with a 60/40 rear seat may be equipped with a folding load floor.
Page 177 WARNING! Do not operate the vehicle with loose items stored on the load floor. While driving or in an accident you may experience abrupt stopping, rapid acceleration, or sharp turns. Loose objects stored on the load floor may move around with force and strike occupants, resulting in serious or fatal injury.
Page 178 176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Grasp the knob on the load floor and lift the knob until the load floor unfolds into position. Load Floor In Open Position 3. Reverse the procedure to store the load floor. Positioning the Load Floor for Storage Access Under the Seat 1.
Page 179: Pickup Box
Load Floor Securing Straps 4. Reverse the procedure to put the load floor back in the secured down position before you operate the vehicle. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 PICKUP BOX Pickup Box Features The pickup box on your new vehicle has many features designed for utility and convenience.
Page 180 178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If you are installing a toolbox to the front of the pickup box, you must use Mopar available from your authorized dealer. You can carry wide building materials (sheets of ply- wood, etc.) by building a raised load floor. Place lumber across the box in the indentations provided above the wheel housings and in the bulkhead dividers to form the floor.
Page 181: Slide-In Campers
There are stampings in the sheet metal on the inner side bulkheads of the box in front of and behind both wheel housings. Place wooden boards across the box from side to side to create separate load compartments in the pickup box.
Page 182 180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Dual rear wheel pickup models require properly spaced rear clearance lights. If such a vehicle is operated without a tailgate, suitable lights must be installed. Tailgate Support Strap Attachment Tailgate Open...
Page 183 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 WARNING! To avoid inhaling carbon monoxide, which is deadly, the exhaust system on vehicles equipped with “Cap or Slide-In Campers” should extend beyond the overhanging camper compartment and be free of leaks.
Page 185: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instruments And Controls ....187 Instrument Cluster ..... . 188 Instrument Cluster –...
Page 186 184 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Hands-Free Phone — If Equipped ......209 Operating Instructions - Satellite Radio —...
Page 187 Noise Reduction ..... . 230 Operating Instructions - (CD Mode For CD Audio Play) ......230 Load/Eject Button (CD Mode For CD Audio Play) .
Page 188 186 UNDERSTANDING YOUR INSTRUMENT PANEL Satellite Antenna ..... . 245 Reception Quality ..... 245 Remote Sound System Controls —...
Page 189: Instruments And Controls
INSTRUMENTS AND CONTROLS 1 — Headlight Switch 6 — Passenger Airbag* 2 — Air Outlets 7 — Glove Box 3 — Instrument Cluster 8 — Passenger Airbag On/Off Switch* 4 — Climate Controls 9 — Power Outlet 5 — Radio 10 —...
Page 190: Instrument Cluster
188 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER Instrument Cluster – 6.7L Diesel Engine...
Page 191: Instrument Cluster Description
INSTRUMENT CLUSTER DESCRIPTION 1. Check Gauges This light illuminates when the Voltmeter, Engine Oil Pressure or Engine Coolant Temperature gauges indicate a reading either too high or too low. Examine the gauges carefully, and follow the instructions contained below for each indicated problem. NOTE: When the ignition switch is turned to OFF, the Fuel Gauge, Voltmeter, Oil Pressure and Engine Coolant Temperature gauges may not show accurate readings.
Page 192 190 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Turn Signal Indicators Lights in instrument cluster flash when outside turn signals are operating. 4. Tachometer The tachometer indicates engine speed in revolutions per minute. CAUTION! Do not operate the engine with the tachometer pointer at high rpm for extended periods.
Page 193 9. Oil Pressure Gauge The pointer should always indicate some oil pres- sure when the engine is running. A continuous high or low reading, under normal driving conditions, may indicate a lubrication system malfunction. Immedi- ate service should be obtained. NOTE: If the gauge pointer moves to either extreme of the gauge, the “Check Gauges”...
Page 194 192 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Do not leave your vehicle unattended with the en- gine running as you would not be able to react to the temperature indicator if the engine overheats. NOTE: Engine idle speed will automatically increase to 1000 rpm at elevated coolant temperatures to improve engine cooling.
Page 195 during repair or replacement, be sure to keep a record of the reading before and after the service so that the correct mileage can be determined. The two trip odometers show individual trip mileage. To switch from odometer to trip odometers, press and release the Trip Odometer button.
Page 196 194 UNDERSTANDING YOUR INSTRUMENT PANEL 17. Malfunction Indicator Light (MIL) This light is part of an onboard diagnostic system which monitors the emissions and engine control system. If the vehicle is ready for emissions testing the light will come on when the ignition is first turned on and remain on, as a bulb check, until the engine is started.
Page 197 If the light remains on when the parking brake is released, it indicates a possible brake hydraulic system malfunction. In this case, the light will remain on until the cause is corrected. If brake failure is indicated, immediate repair is necessary and continued operation of the vehicle in this condition is dangerous.
Page 198 196 UNDERSTANDING YOUR INSTRUMENT PANEL experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing. The light will come on when the ignition is first turned on and remain on for 15 seconds as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer.
Page 199 As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accord- ingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure.
Page 200 198 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, type, and/or style.
Page 201 Follow engine starting procedure for proper engine start- ing and operating. Wait until the Wait To Start indicator turns OFF, then start the vehicle. NOTE: The Wait To Start Indicator may not illuminate if the engine coolant temperature is warm enough. 27.
Page 202: Electronic Digital Clock
200 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC DIGITAL CLOCK The clock and radio each use the display panel built into the radio. A digital readout shows the frequency and/or time in hours and minutes (depending on your radio model) whenever the ignition switch is in the ON or ACC position.
Page 203: Two Types Of Signals
Two Types of Signals There are two basic types of radio signals: AM or Amplitude Modulation, in which the transmitted sound causes the amplitude, or height, of the radio waves to vary; and FM or Frequency Modulation, in which the frequency of the wave is varied to carry the sound.
Page 204: Sales Code Ref - Am/Fm/Cd (Single Disc) Radio With Optional Satellite Radio And Hands Free Phone Capability
202 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE REF — AM/FM/CD (SINGLE DISC) RADIO WITH OPTIONAL SATELLITE RADIO AND HANDS FREE PHONE CAPABILITY NOTE: The radio sales code is located on the lower right side of your radio faceplate. REF Radio Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
Page 205 Mode Button (Radio Mode) Press the MODE button repeatedly to select between the CD player and Satellite Radio (if equipped). SEEK Button (Radio Mode) Press and release the SEEK button to search for the next listenable station in either AM/FM or Satellite (if equipped) mode.
Page 206 204 UNDERSTANDING YOUR INSTRUMENT PANEL Clock Setting Procedure 1. Press and hold the TIME button until the hours blink. 2. Adjust the hours by turning the TUNE/AUDIO con- trol. 3. After the hours are adjusted, press the TUNE/AUDIO control to set the minutes. The minutes will begin to blink.
Page 207 Press the rotary TUNE control a fourth time and BAL will display. Turn the TUNE control to the right or left to adjust the sound level from the right or left side speakers. Press the rotary TUNE control a fifth time and FADE will display.
Page 208: Operating Instructions - Cd Mode
206 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - CD Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Inserting The Compact Disc (Single CD Player) Gently insert one CD into the CD player with the CD label facing up.
Page 209 SCAN Button (CD Mode) Press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time. EJECT Button (CD Mode) Press this button and the disc will unload and move to the entrance for easy removal.
Page 210: Operating Instructions - Auxiliary Mode
208 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device such as an MP3 player, cassette player, or microphone and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers.
Page 211: Operating Instructions - Hands-Free Phone - If
TIME Button (Auxiliary Mode) Press this button to change the display from elapsed playing time to time of day. The time of day will display for five seconds. RW/FF (Auxiliary Mode) No function. RND/SET Button (Auxiliary Mode) No function. Mode Button (Auxiliary Mode) Press the MODE button repeatedly to select between the CD player and Satellite Radio (if equipped).
Page 212: Sales Code Raq - Am/Fm/Cd (6-Disc) Radio
210 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RAQ – AM/FM/CD (6-DISC) RADIO WITH OPTIONAL SATELLITE RADIO, HANDS-FREE PHONE, AND VIDEO ENTERTAINMENT SYSTEMS (VES™) CAPABILITIES NOTE: The radio sales code is located on the lower right side of your radio faceplate. RAQ Radio Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC...
Page 213 Mode Button (Radio Mode) Press the MODE button repeatedly to select between the CD player, Satellite Radio, or Video Entertainment Sys- tem (VES)™ (if equipped). SEEK Button (Radio Mode) Press and release the SEEK button to search for the next listenable station in either AM/FM or Satellite (if equipped) mode.
Page 214 212 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button Press the TIME button and the time of day will be displayed for five seconds. Clock Setting Procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the TUNE/AUDIO con- trol.
Page 215 Press the rotary TUNE control a second time and MID will display. Turn the TUNE control to the right or left to increase or decrease the Mid Range tones. Press the rotary TUNE control a third time and TREBLE will display. Turn the TUNE control to the right or left to increase or decrease the Treble tones.
Page 216 214 UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the PTY button to select the following format types: Program Type No program type or undefined Adult Hits Alert Alert Classical Classic Rock College Country Emergency Test Foreign Language Information Jazz News Nostalgia 16 Digit-Character Display None Adult_Hits...
Page 217 By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. If a preset button is activated while in the PTY (Program Type) mode, the PTY mode will be exited and the radio will tune to the preset station.
Page 218: Operating Instructions
216 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - (CD Mode for CD Audio Play) NOTE: The ignition switch must be in the ON or ACC position to operate the radio. NOTE: This Radio is capable of playing compact discs (CD), recordable compact discs (CD-R), rewritable com- pact discs (CD-RW) compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks.
Page 219: Play)
SEEK Button (CD Mode for CD Audio Play) Press the right side of the SEEK button for the next selection on the CD. Press the left side of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection.
Page 220 218 UNDERSTANDING YOUR INSTRUMENT PANEL Radio display will show EJECTING DISC when the disc is being ejected and prompt the user to remove the disc. Press and hold the LOAD/ EJT button for five seconds and all CDs will be ejected from the radio. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded.
Page 221: Notes On Playing Mp3 Files
RND/PTY Button (Random Play Button) (CD Mode for CD Audio Play) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. Press the SEEK button to move to the next randomly selected track.
Page 222 220 UNDERSTANDING YOUR INSTRUMENT PANEL • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator 3-character extension) • Level 2: 31 (including a separator 3-character extension) Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3 files).
Page 223: Audio Play)
Playlist files are not supported. MP3 Pro files are not supported. Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
Page 224 222 UNDERSTANDING YOUR INSTRUMENT PANEL PLEASE WAIT and prompt when to INSERT DISC. After the radio displays LOAD DISC insert the CD into the player. Radio display will show LOADING DISC when the disc is loading. LOAD/EJECT - Eject Press the LOAD/ EJECT button and the push- button with the corresponding number where the CD was loaded and the disc will unload and move to the entrance for easy removal.
Page 225 TUNE Control (CD Mode for MP3 Play) Pressing the TUNE control allows the adjustment of Tone, Balance, and Fade. AM/FM Button (CD Mode for MP3 Play) Switches back to Radio mode. RND/ PTY Button (CD Mode for MP3 Play) Pressing this button plays files randomly. SET/DIR Button (CD Mode for MP3 Play) Press the SET/DIR Button to display folders, when playing an MP3 discs that have a file/folder structure.
Page 226: Sales Code Rak - Am/Fm/Cassette/Cd (6-Disc) Radio With Optional Satellite Radio, Hands Free Phone, Video, Mp3, And Wma Capabilities
224 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RAK – AM/FM/CASSETTE/CD (6-DISC) RADIO WITH OPTIONAL SATELLITE RADIO, HANDS FREE PHONE, VIDEO, MP3, and WMA CAPABILITIES NOTE: The radio sales code is located on the lower right side of your radio faceplate. RAK Radio Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC...
Page 227 SEEK Button (Radio Mode) Press and release the SEEK button to search for the next station in either AM/FM or Satellite (if equipped) mode. Press the right side of the button to seek up and the left side to seek down. The radio will remained tuned to the new station until you make another selection.
Page 228 226 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF (Radio Mode) Pressing the rewind/fast forward button causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either AM, FM or Satel- lite (if equipped) frequencies. TUNE Control (Radio Mode) Turn the right side rotary control to increase or decrease the frequency.
Page 229 UNDERSTANDING YOUR INSTRUMENT PANEL 227 Turn the tune knob to select the following format types: 16 Digit-Character Program Type Display 16 Digit-Character Program Type Display Nostalgia Nostalgia No program type or un- Jazz Jazz None defined Classical Classical News News Rhythm and Blues Rhythm_and_Blues Information...
Page 230: Operating Instructions - Tape Player
228 UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. If a preset button is activated while in the PTY (Program Type) mode, the PTY mode will be exited and the radio will tune to the preset station.
Page 231: Fast Forward (Ff)
Fast Forward (FF) Press the FF button up momentarily to advance the tape in the direction that it is playing. The tape will advance until the button is pressed again or the end of the tape is reached. At the end of the tape, the tape will play in the opposite direction.
Page 232: Noise Reduction
230 UNDERSTANDING YOUR INSTRUMENT PANEL Noise Reduction The Dolby Noise Reduction System* is on whenever the tape player is on, but may be switched off. To turn off the Dolby Noise Reduction System: Press Preset 1 after you insert the tape. The NR light in the display will go off when the Dolby System is off.
Page 233: Load/Eject Button (Cd Mode For Cd Audio Play)
If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the disc number, the track number, and index time in minutes and seconds.
Page 234 232 UNDERSTANDING YOUR INSTRUMENT PANEL Radio display will show EJECTING DISC when the disc is being ejected and prompt the user to remove the disc. Press and hold the LOAD/EJT button for five seconds and all CDs will be ejected from the radio. If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded.
Page 235: Notes On Playing Mp3 Files
RND/PTY Button (Random Play Button) (CD Mode for CD Audio Play) Press this button while the CD is playing to activate Random play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace. NOTE: MP3 and WMA Random play are for file folders only.
Page 236 234 UNDERSTANDING YOUR INSTRUMENT PANEL The radio uses the following limits for file systems: • Maximum number of directory levels: 15 • Maximum number of files: 255 • Maximum number of folders: 100 • Maximum number of characters in file/folder names: •...
Page 237 MPEG Sampling Fre- Specification quency (kHz) MPEG-1 Audio 48, 44.1, 32 Layer 3 MPEG-2 Audio 24, 22.05, 16 Layer 3 ID3 Tag information for artist, song title, and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios.
Page 238: Operating Instructions - (Cd Mode For Mp3 And Wma Audio Play)
236 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - (CD Mode for MP3 and WMA Audio Play) SEEK Button (CD Mode for MP3 and WMA Play) Pressing the right side of the SEEK button plays the next file. Pressing the left side of the SEEK button plays the beginning of the file.
Page 239 INFO Button (CD Mode for MP3 Play) Press the INFO button while playing MP3 or WMA disc. The radio scrolls through the following TAG information: Song Title, Artist, File Name, and Folder Name (if avail- able). Press the INFO button once more to return to elapsed time priority mode.
Page 240: Sales Code Rec - Am/Fm/Cd (6-Disc) Radio
238 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Hands Free Phone (If Equipped) Refer to “Hands-Free Phone” in Section 3 of the Owner’s Manual. Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the “Satellite Radio” section of the Owner’s Manual.
Page 241: Equipped
menus and instructions for selecting a variety of destina- tions and routes, AM/FM stereo radio and six-disc CD changer with MP3 capability. Mapping information for navigation is supplied on a DVD that is loaded into the unit. One map DVD covers all of North America.
Page 242 240 UNDERSTANDING YOUR INSTRUMENT PANEL 2. To show the GPS clock, select “Displayed Clock: GPS Clock” and press ENTER. 3. To adjust the time zone, Select “Time Zone” and press ENTER. Select the appropriate time zone and press ENTER. 4. To turn daylight savings on or off, select “Daylight Savings”...
Page 243: Video Entertainment System (Sales Code Xrv) - If Equipped
3. To decrease the clock by one hour, use the Select Encoder to highlight the “-” sign. Press ENTER. Press ENTER again to decrease the clock by another hour. 4. To increase the clock by minutes, make sure “MIN +” is highlighted and press ENTER.
Page 244: System Activation
242 UNDERSTANDING YOUR INSTRUMENT PANEL System Activation Sirius Satellite Radio service is pre-activated, and you may begin listening immediately to the one year of audio service that is included with the factory-installed satellite radio system in your vehicle. Sirius will supply a wel- come kit that contains general information, including how to setup your on-line listening account at no addi- tional charge.
Page 245: Selecting Satellite Mode In Ref, Raq, And Rak Radios
when any other button is pushed, the ignition is turned OFF, or five minutes have passed since any button was pushed. ESN/SID Access with REC Navigation Radios Please refer to your Navigation User’s Manual. With the ignition in the ACC position and the radio off, press the CD Eject and SET buttons simultaneously until the 12 digits of the ESN/SID appear on the screen.
Page 246: Storing And Selecting Preset Channels
244 UNDERSTANDING YOUR INSTRUMENT PANEL Press and release the SCAN button (if equipped) to automatically change channels every seven seconds. The radio will pause on each channel for seven seconds before moving on to the next channel. The word SCAN will appear in the display between each channel change.
Page 247: Pty Button Seek
PTY Button SEEK When the desired program is obtained, press the SEEK button within five seconds. The channel will change to the next channel that matches the program type selected. Satellite Antenna To ensure optimum reception on vehicles available with a luggage rack, do not place items on the roof around the rooftop antenna location.
Page 248: Remote Sound System Controls - If Equipped
246 UNDERSTANDING YOUR INSTRUMENT PANEL REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. Remote Sound System Controls The right-hand control is a rocker type switch with a button in the center.
Page 249: Tape Player
Tape Player Pressing the top of the switch once will go to the next selection on the cassette. Pressing the bottom of the switch once will go to the beginning of the current selection or to the beginning of the previous selection if it is within the first five seconds of the current selection.
Page 250: Compact Disc Maintenance
248 UNDERSTANDING YOUR INSTRUMENT PANEL 5. A loose tape should be corrected before use. To rewind a loose tape, insert the eraser end of a pencil into the tape drive gear and twist the pencil in the required direction. Maintain your cassette tape player. The head and capstan shaft in the cassette player can pick up dirt or tape deposits each time a cassette is played.
Page 251: Radio Operation And Cellular Phones
NOTE: If you experience difficulty in playing a particu- lar disc, it may be damaged, oversized, or have theft protection encoding. Try a known good disc before considering disc player service. RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the operation of a cellular phone in your vehicle can cause erratic or noisy perfor- mance from your radio.
Page 252: Heater Only - If Equipped
250 UNDERSTANDING YOUR INSTRUMENT PANEL Heater Only — If Equipped Manual Heating Controls The mode control (at the right of the control panel) can be set in any of the following positions: NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes.
Page 253 Recirculation Modes (Panel or Bi-Level) Select the recirculation modes when the outside air contains smoke or odors. This feature allows for recircu- lation of interior air only. Air flows through the panel outlets in this mode. Air flows through the panel only, or through both the panel and floor vents depending on the selected mode (panel vs bi-level).
Page 254: Air Conditioning And Heating
252 UNDERSTANDING YOUR INSTRUMENT PANEL Air Conditioning and Heating — If Equipped Air Conditioning And Heating Air Conditioning Operation To turn on the Air Conditioning, set the fan control at any speed and press the snowflake button located at the right of the control panel. Conditioned air will be directed through the outlets selected by the mode control.
Page 255 NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are iden- tified by the small dots. Recirculation Modes (Panel or Bi-Level) Select the recirculation modes when the outside air contains smoke, odors, high humidity, or if rapid cooling is desired.
Page 256 254 UNDERSTANDING YOUR INSTRUMENT PANEL the windshield, and the demister outlets located at the edge of each side of the instrument panel, and the air conditioning may be on. NOTE: The air conditioning compressor operates in both Mix and Defrost or a blend of these modes, even if the A/C button has not been pressed.
Page 257: Air Conditioning With Dual Zone Temperature
Side window demisters direct airflow specifically to the window glass to help prevent interior fogging of the glass. They are located in the extreme outside upper edges of the instrument panel. The demisters also pro- vide extra air ducts for circulation. They are in operation whenever the Floor, Mix or Defrost modes are in use.
Page 258 256 UNDERSTANDING YOUR INSTRUMENT PANEL Air Conditioning and Heating Operation To turn on the Air Conditioning, set the fan control at any speed and press the snowflake button located on the control panel. Conditioned air will be directed through the outlets selected by the mode control. A light in the snowflake button shows that the air conditioning is on.
Page 259 NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are iden- tified by the small dots and give an even blend of both modes. Panel Outside air flows through the outlets located in the instrument panel.
Page 260 258 UNDERSTANDING YOUR INSTRUMENT PANEL Blower Control The rotary knob on the left of the control panel is the blower control. Turn the knob clockwise to one of the four positions to obtain the blower speed you desire. To turn the blower off, turn the knob to the far left posi- tion.
Page 261 Circulation The cab is designed with features to promote outside air circulation. There are grilles in the cab back panel. These are air exhausters that provide the means for regular exchange of cab air. Side window demisters direct airflow specifically to the window glass to help prevent interior fogging of the glass.
Page 262: Operating Tips
260 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips Fast Cooldown For a fast cooldown, turn the blower fan rotary knob to the extreme right position, turn the mode control to the panel fresh position, press the snowflake button to turn on the air conditioning, and drive with the windows open for the first few minutes.
Page 263 Summer Operation Air conditioned vehicles must be protected with a high quality antifreeze coolant during summer to provide proper corrosion protection and to raise the boiling point of the coolant for protection against overheating. A 50 % concentration is recommended. For proper coolant type, refer to “Recommended Fluids and Genuine Parts”...
Page 264: Operating Tips Chart
262 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips Chart...
Page 265: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures – Diesel Engines ..268 Automatic Transmission – If Equipped ..268 Manual Transmission – If Equipped ..269 Normal Starting Procedure –...
Page 266 264 STARTING AND OPERATING Manual Transmission ....291 Shifting ......291 Downshifting .
Page 267 Tire Identification Number (TIN) ..319 Tire Loading And Tire Pressure ... 320 Tires — General Information ....324 Tire Pressure .
Page 268 266 STARTING AND OPERATING Fuel Requirements ..... . 348 Fuel Requirements (6.7L Diesel Engines) ..348 Adding Fuel (Diesel Engines) .
Page 269 Recreational Towing (Behind Motorhome, Etc.) . . 375 Recreational Towing – 2-Wheel Drive Models ......375 STARTING AND OPERATING 267 Recreational Towing –...
Page 270: Starting Procedures - Diesel Engines
268 STARTING AND OPERATING STARTING PROCEDURES – DIESEL ENGINES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. The starter should not be operated for more than 15- second intervals. Waiting a few minutes between such intervals will protect the starter from overheating.
Page 271: Manual Transmission - If Equipped
NOTE: The engine block heater cord is a factory in- stalled option. If your vehicle is not equipped, heater cords are available from your authorized Mopar dealer. • A 12–volt heater built into the fuel filter housing aids in preventing fuel gelling. It is controlled by a built-in thermostat.
Page 272: Starting Procedure - Engine Manifold Air Temperature Below 66°F (19°C)
270 STARTING AND OPERATING CAUTION! If WATER IN FUEL indicator light remains on DO NOT START engine before you drain water from the fuel filter to avoid engine damage. Refer to “Drain- ing Fuel/Water Separator Filter (6.7L Diesel Engine)” under “Maintenance Procedures” in Section 7. 4.
Page 273 Follow the steps in the Normal Starting Procedure ex- cept: CAUTION! Do not crank engine for more than 15 seconds at a time or starter motor damage may result. Turn key to OFF and wait at least two minutes for starter to cool before repeating start procedure.
Page 274 272 STARTING AND OPERATING For Extremely Cold Weather Starting — Engine Manifold Air Temperature Below 0°F (-18°C) In extremely cold weather below 0°F (-18°C) it may be beneficial to cycle the manifold heaters twice before attempting to start the engine. This can be accomplished by turning the ignition OFF for at least five seconds and then back ON after the WAIT TO START light has gone off, but before the engine is started.
Page 275 • If the engine is started before the WAIT TO START light turns off, the preheat cycle will turn off. • If the engine is cranked for more than 10 seconds, the post-heat cycle will turn off. NOTE: Engine idle speed will automatically increase to 1000 RPM at low coolant temperatures to improve engine warm-up.
Page 276: Starting Fluids
274 STARTING AND OPERATING Starting Fluids WARNING! STARTING FLUIDS or flammable liquids are NEVER TO BE USED in the Cummins Diesel (see Warning label). Never pour diesel fuel, flammable liquid, starting fluids (ether) into the air cleaner canister, air intake piping, or turbocharger inlet in an attempt to start the vehicle.
Page 277: Cold Weather Precautions
• Voltmeter Operation: 1. The voltmeter may show a gauge fluctuation if certain engine temperatures are below 66°F (19°C). This cycling operation is caused by the post-heat cycle of the intake manifold heater system. The number of cycles and the length of the cycling operation is controlled by the engine control module.
Page 278 276 STARTING AND OPERATING • Climatized Ultra Low Sulfur Diesel Fuel is a blend of Number 2 Ultra Low Sulfur and Number 1 Ultra Low Sulfur Diesel Fuels which reduces the temperature at which wax crystals form in fuel. NOTE: The engine requires the use of “Ultra Low Sulfur Diesel Fuel”.
Page 279 Block Heater Usage A. Temperatures below 0°F (-18°C) • Block Heater Required for 15W-40 • Block Heater Recommended for 5W-40 B. Temperatures below - 20°F (-29°C) • Block Heater Required for 5W-40 Winter Front Usage If a winter front or cold weather cover is to be used, a percentage of the total grille opening area must be left uncovered to provide sufficient air flow to the charge air cooler and automatic transmission oil cooler.
Page 280: Engine Idling
278 STARTING AND OPERATING NOTE: High-speed, no-load running of a cold engine can result in excessive white smoke and poor engine performance. No-load engine speeds should be kept under 1,200 rpm during the warm-up period, especially in cold ambient temperature conditions. If temperatures are below 32°F (0°C), operate the engine at moderate speeds for 5 minutes before full loads are applied.
Page 281 NOTE: An optional driver-controlled high idle speed is available on automatic transmission equipped vehicles with speed control. This feature allows the driver to select an elevated idle speed between 1100 and 1500 rpms. Your dealer can enable this feature. The optional driver-controlled high idle speed will help increase cylinder temperatures and provide additional cab heat, however, may still cause the exhaust aftertreat- ment system to not properly regenerate.
Page 282: Stopping The Engine
280 STARTING AND OPERATING Stopping The Engine Idle the engine a few minutes before routine shutdown. After full load operation, idle the engine 3 to 5 minutes before shutting it down. This idle period will allow the lubricating oil and coolant to carry excess heat away from the combustion chamber, bearings, internal components, and turbocharger.
Page 283: Engine Speed Control
Engine Speed Control CAUTION! Prevent overspeeding the engine going down hill. When descending steep grades, use a combination of gears and service brakes to control vehicle/engine speed. Overspeed can cause severe engine damage. Operating Precautions Avoid Overheating The Engine The temperature of the coolant (a mixture of 50% ethylene-glycol and 50% water) must not exceed the normal range of the temperature gauge (240°F/116°C) with a 16 psi (110 kPa) radiator cap.
Page 284 282 STARTING AND OPERATING • Up Steep Hills — select a lower transmission gear, but try and keep the torque converter clutch engaged. • Air Conditioning — turn it off temporarily. Do Not Operate The Engine With Low Oil Pressure When the engine is at normal operating temperature, the minimum oil pressures required are: Idle 700 to 800 RPM .
Page 285: Diesel Exhaust Brake (Engine Braking)
STARTING AND OPERATING 283 DIESEL EXHAUST BRAKE (ENGINE BRAKING) – IF EQUIPPED The exhaust brake feature will only function when the driver turns the exhaust brake switch to the ON position. Once the switch is in the ON position and the vehicle is moving faster than 5 mph (8 km/h);...
Page 286 284 STARTING AND OPERATING WARNING! Do not use the Exhaust Brake feature when driving in icy or slippery conditions as the increased engine braking can cause the rear wheels to slide and the vehicle to swing around with the possible loss of vehicle control, which may cause an accident possi- bly resulting in personal injury or death.
Page 287: Transmission Shifting
TRANSMISSION SHIFTING Automatic Transmission with Overdrive (68RFE) — If Equipped The gear selector lever display located in the instrument panel cluster indicates the transmission gear range (the selector is illuminated for night driving). The selector lever is mounted on the right side of the steering column. You must depress the brake pedal to pull the selector lever out of PARK position (Brake Interlock System).
Page 288 286 STARTING AND OPERATING WARNING! Your vehicle could move and injure you and others if it is not completely in PARK. Check by trying to move the shift lever back and forth without first pulling it toward you after you have set it in PARK. Make sure it is in PARK before leaving the vehicle.
Page 289 Upshifts into both overdrive gears, 5th and 6th, will be delayed when the transmission fluid temperature is below 40° F (4.5° C) or above 240° F (115.5° C). NOTE: Use caution when operating a heavily loaded vehicle in 2nd or 1st gear in high ambients as torque converter slip can impose significant additional heat load on the cooling system.
Page 290 288 STARTING AND OPERATING NOTE: If the vehicle is started in extremely cold tem- peratures, the transmission may not shift into Overdrive and will automatically select the most desirable gear for operation at this temperature. Normal operation will resume when the transmission fluid temperature has risen to a suitable level.
Page 291 delayed. Shifts into 5th and 6th gear are still allowed under steady cruise conditions. Closed throttle down- shifts (for improved engine braking) may occur during steady braking maneuvers. Pressing the switch a second time restores normal operation. Normal operation is always the default at engine start-up.
Page 292 290 STARTING AND OPERATING NOTE: To select the proper gear position for maximum deceleration (engine braking), simply press and hold the switch down (-). The transmission will shift to the range from which the vehicle can best be slowed down. Torque Converter Clutch A feature designed to improve fuel economy has been included in the automatic transmission on your vehicle.
Page 293: Manual Transmission
MANUAL TRANSMISSION WARNING! You or others could be injured if you leave the vehicle unattended without having the parking brake fully applied. The parking brake should al- ways be applied when the driver is not in the vehicle, especially on an incline. CAUTION! Never drive with your foot resting on the clutch pedal, or attempt to hold the vehicle on a hill with the...
Page 294 292 STARTING AND OPERATING Truck models with manual transmission are equipped with a clutch interlocking ignition system. The clutch pedal must be fully depressed to start the vehicle. Fully depress the clutch pedal before shifting gears. As you release the clutch pedal, lightly depress the accelera- tor pedal.
Page 295: Downshifting
Downshifting Moving from a high gear down to a lower gear is recommended to preserve brakes when driving down steep hills. In addition, downshifting at the right time provides better acceleration when you desire to resume speed. Downshift progressively. Do not skip gears to avoid overspeeding the engine and clutch.
Page 296: Reverse Shifting
294 STARTING AND OPERATING Maximum Recommended Downshifting Speeds Gear Selec- 6 to 5 5 to 4 4 to 3 tion Maxi- 68 mph 50 mph 32 mph (109 Speed km/h) km/h) km/h) Reverse Shifting To shift into REVERSE (R), bring the vehicle to a com- plete stop.
Page 297 This transfer case is intended to be driven in the 2-wheel drive position (2H) for normal street and highway con- ditions such as dry hard surfaced roads. When additional traction is required the transfer case 4H and 4L positions can be used to lock the front and rear driveshafts together and force the front and rear wheels to rotate at the same speed.
Page 298 296 STARTING AND OPERATING NOTE: Delayed shifts out of four-wheel drive may be experienced due to uneven tire wear, low or uneven tire pressures, excessive vehicle loading, or cold tempera- tures. WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the NEUTRAL position without first fully engaging the parking brake.
Page 299: Shifting Procedure - Manually Shifted Transfer
4-Wheel Drive Low Range - Low speed 4-wheel drive. Locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed. Additional traction and maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h).
Page 300: Transfer Case Reminder Light
298 STARTING AND OPERATING vehicle in motion, the transfer case will engage/ disengage faster if you momentarily release the accelera- tor pedal after completing the shift. Apply a constant force when shifting the transfer case lever. 2H or 4H ⇔ 4L With the vehicle rolling at 2 to 3 mph (3 to 5 km/h), shift an automatic transmission to NEUTRAL or depress the clutch on a manual transmission.
Page 301: Electronically Shifted Transfer Case Operating Information/Precautions (4 Position Switch) - If Equipped
Electronically Shifted Transfer Case Operating Information/Precautions (4 Position Switch) — If Equipped Transfer Case Switch STARTING AND OPERATING 299 This is an electric shift transfer case and is operated by the 4WD Control Switch (Transfer Case Switch), which is located on the instrument panel. This Electronically Shifted transfer case provides four mode positions: 2 (rear)-wheel drive high range, 4-wheel drive lock range, 4-wheel drive low range, and NEU-...
Page 302 300 STARTING AND OPERATING in the 4WD LOCK and 4WD LOW positions on dry hard surfaced roads may cause increased tire wear and dam- age to the driveline components. NOTE: The transfer case NEUTRAL position is selected by depressing the recessed button located on the lower left hand corner of the 4WD Control Switch.
Page 303 If One or More Shift Conditions Are Not Met: 1. The indicator light for the current position will remain 2. The newly selected position indicator light will con- tinue to flash. 3. The transfer case will not shift. NOTE: Before retrying a selection, make certain that all the necessary requirements for selecting a new transfer case position have been met.
Page 304 302 STARTING AND OPERATING When operating your vehicle in 4WD LOW, the engine speed is approximately three times that of the 2WD or 4WD LOCK positions at a given road speed. Take care not to overspeed the engine and do not exceed 25 mph (40 km/h).
Page 305: Shifting Procedure - Electronically Shifted
4WD LOCK 4-Wheel Drive Lock Range - Locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed. Additional traction for loose, slippery road surfaces only. 4WD LOW 4-Wheel Drive Low Range - Low speed 4-wheel drive. Locks the front and rear driveshafts together.
Page 306 304 STARTING AND OPERATING light will continue to flash until all the requirements for the selected position have been met. To retry a shift: return the control knob back to the original position, make certain all shift requirements have been met, wait five seconds and try the shift again.
Page 307 Preferred Procedure 1. With engine running, slow vehicle to 2 to 3 mph (3 to 5 km/h). 2. Shift the transmission into NEUTRAL (depress clutch on manual transmissions). 3. While still rolling, rotate the transfer case control switch to the desired position. 4.
Page 308: Limited-Slip Differential - If Equipped
306 STARTING AND OPERATING LIMITED-SLIP DIFFERENTIAL — IF EQUIPPED The limited-slip differential provides additional traction on snow, ice, mud, sand and gravel, particularly when there is a difference between the traction characteristics of the surface under the right and left rear wheels. During normal driving and cornering, the limited-slip unit per- forms similarly to a conventional differential.
Page 309: Driving On Slippery Surfaces
DRIVING ON SLIPPERY SURFACES When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability.
Page 310: Shallow Standing Water
308 STARTING AND OPERATING Shallow Standing Water Although your vehicle is capable of driving through shallow standing water, consider the following Caution and Warning before doing so. CAUTION! • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle.
Page 311: Driving Off-Road
WARNING! • Driving through standing water limits your vehi- cle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. • Driving through standing water limits your vehi- cle’s braking capabilities, which increases stop- ping distances. Therefore, after driving through standing water, drive slowly and lightly press on the brake pedal several times to dry the brakes.
Page 312: Parking Brake
310 STARTING AND OPERATING NOTE: After off-road usage, particularly in sand or mud, inspect the underside of the vehicle for accumu- lated dirt at the propeller shaft, axles, U-joints, brake rotors and calipers. Use a hose to clean off any accumulation of dirt or mud. Check the exhaust system and all exposed components for any sign of damage.
Page 313 Parking Brake Release Be sure the parking brake is firmly set when parked and the shift lever is in the PARK position. When parking on a hill you should apply the parking brake before placing the shift lever in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever out of PARK.
Page 314: Brake System
312 STARTING AND OPERATING When parking on a hill, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. The parking brake should always be applied whenever the driver is not in the vehicle. BRAKE SYSTEM If power assist is lost for any reason (for example, repeated brake applications with the engine off), the...
Page 315: Four-Wheel Anti-Lock Brake System
Four-Wheel Anti-Lock Brake System WARNING! Anti-Lock Brake Systems contain sophisticated elec- tronic equipment. It may be susceptible to interfer- ence caused by improperly installed or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability. Installation of such equipment should be performed by qualified professionals.
Page 316 314 STARTING AND OPERATING This Anti-lock Brake System is designed to aid the driver in maintaining vehicle control under adverse braking conditions. The system operates with a separate com- puter to modulate hydraulic pressure to prevent wheel lockup and help avoid skidding on slippery surfaces. The system’s pump motor runs during an ABS stop to provide regulated hydraulic pressure.
Page 317: Power Steering
POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible to steer your vehicle.
Page 318: Tire Safety Information
316 STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings NOTE: • P (Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tire sizing is based on European design standards.
Page 319 Tire Sizing Chart Size Designation: P = Passenger Car tire size based on U.S. design standards ...blank... = Passenger Car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect ratio in percent (%).
Page 320 318 STARTING AND OPERATING Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load correspond- ing to its load index under certain operating conditions —...
Page 321: Tire Identification Number (Tin)
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, DOT = Department of Transportation —...
Page 322: Tire Loading And Tire Pressure
320 STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side B-Pillar. Tire Placard Location Tire and Loading Information Placard Tire And Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle...
Page 323 Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading Information placard and in the “Vehicle Loading”...
Page 324 322 STARTING AND OPERATING available cargo and luggage load capacity is 650 lbs (295 kg) {(since 5 x 150 = 750, and 1400 – 750 = 650 lbs (295 kg)}. 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.
Page 325 STARTING AND OPERATING 323...
Page 326: Tires - General Information
324 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 327: Tire Inflation Pressures
2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under-inflation also increases tire rolling resistance and results in higher fuel consump- tion.
Page 328 326 STARTING AND OPERATING check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under-inflated. CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem.
Page 329: Radial Ply Tires
Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important.
Page 330: Compact Spare Tire - If Equipped
328 STARTING AND OPERATING Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and rein- stalled at the first opportunity.
Page 331: Tire Spinning
original equipped tire on the front or rear axle of your vehicle, but it is not. Installation of this limited-use spare tire affects vehicle handling. Since it is not the same tire, replace (or repair) the original tire and reinstall on the vehicle at the first opportunity.
Page 332: Tread Wear Indicators
330 STARTING AND OPERATING Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm).
Page 333: Replacement Tires
WARNING! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have an accident resulting in serious injury or death. Keep dismounted tires in a cool, dry place with as little exposure to light as possible.
Page 334: Alignment And Balance
332 STARTING AND OPERATING WARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, result- ing in changes to steering, handling, and braking of your vehicle.
Page 335: Supplemental Tire Pressure Information - If Equipped
Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. SUPPLEMENTAL TIRE PRESSURE INFORMATION — IF EQUIPPED A light load vehicle condition is defined as two passen- gers [150 lbs (68 kg) each] plus 200 lbs (91 kg) of cargo.
Page 336 334 STARTING AND OPERATING These cautions apply to all chain traction devices, includ- ing link and cable (radial) chains. Tire chain use is permitted only on the rear tires of Ram 4X2 trucks. NOTE: The use of class “U” chains is permitted on the front and rear of 4X4, 2500 Ram Trucks with LT245/ 70R17E tires.
Page 337: Snow Tires
SNOW TIRES Snow tires should be of the same size and type construc- tion as the front tires. Consult the manufacturer of the snow tire to determine any maximum vehicle speed requirement associated with the tire. These tires should always be operated at the vehicle maximum capacity inflation pressures under any load condition.
Page 338 336 STARTING AND OPERATING Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permis- sible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being per- formed.
Page 339: Dual Rear Wheels
Dual Rear Wheels The tires used on dual wheel assemblies should be matched for wear to prevent overloading one tire in a set. To check if tires are even, lay a straight edge across all four tires. The straight edge should touch all the tires. STARTING AND OPERATING 337 CAUTION! 3500 Dual Rear Tires have only one approved direc-...
Page 340: Tire Pressure Monitor System (Tpms) - If Equipped
338 STARTING AND OPERATING TIRE PRESSURE MONITOR SYSTEM (TPMS) — IF EQUIPPED The Tire Pressure Monitoring System (TPMS) will warn the driver of a low tire pressure based on the vehicle recommended cold tire inflation placard pressure. The placard pressure is defined on the Tire and Loading Information label.
Page 341 The TPM System will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above recom- mended cold placard pressure. Once the low tire pressure warning has been illuminated, the tire pressure must be increased to the recommended cold placard pressure in order for the TPMS warning lamp to be turned off.
Page 342 340 STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure always reinstall the valve stem cap. This will prevent mois- ture and dirt from entering the valve stem, which could damage the Tire Pressure Monitoring Sensor. NOTE: • The TPMS is not intended to replace normal tire care and maintenance, nor to provide warning of a tire failure or condition.
Page 343: Tire Pressure Monitor System (Tpms) "Light Load" Reset Switch Description - If Equipped
Tire Pressure Monitor System (TPMS) “Light Load” Reset Switch Description – If Equipped WARNING! Never operate your vehicle with the TPMS and tire pressures set to the Light Load Inflation Pressure settings if carrying more than two occupants (150 lbs each) plus 200 pounds of cargo.
Page 344 342 STARTING AND OPERATING Light Load Reset Switch “Light Load” Reset Switch Operation – If Equipped • This vehicle may have different recommended tire pressure values between the front and rear tires as shown in both the Tire Loading Information Label and the Supplemental Tire Pressure Information Label.
Page 345 Example Supplemental Tire Pressure Label To switch from the max load inflation pressure (cold) low pressure warning threshold to the light load inflation pressure (cold) low pressure warning threshold, begin by placing the ignition switch in the RUN position. Next, lower all four road tire pressures to the Light Load Inflation Pressure values as listed on the Supplemental STARTING AND OPERATING 343...
Page 346: Tire Pressure Monitor System Components
344 STARTING AND OPERATING WARNING! It is the driver’s responsibility to change to the max load inflation pressure (cold) low pressure warning threshold condition when not driving in the light load condition as defined as two occupants ( 150 lbs each) plus 200 pounds of cargo.
Page 347 NOTE: It is particularly important, for you to check the tire pressure in all of your tires regularly and to maintain the proper pressure. The Tire Pressure Monitoring System (TPMS) consists of the following components: • Receiver Module • 4 Wheel Sensors •...
Page 348 346 STARTING AND OPERATING the ignition key is cycled, this sequence will repeat, providing the system fault still exists. A system fault can occur by any of the following scenarios: 1. Signal interference due to electronic devices or driving next to facilities emitting the same Radio Frequencies as the TPM sensors.
Page 349: General Information
Light will turn OFF, as long as no tire pressure is below the low-pressure warning limit in any of the four active road tires. The vehicle may need to be driven for up to 10 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information.
Page 350: Fuel Requirements
348 STARTING AND OPERATING FUEL REQUIREMENTS Fuel Requirements (6.7L Diesel Engines) Use good quality diesel fuel from a reputable supplier in your vehicle. Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.
Page 351: Adding Fuel (Diesel Engines)
Fuel Specifications The Cummins Turbocharged, Charge Air Cooled, Diesel engine has been developed to take advantage of the high energy content and generally lower cost No. 2 Ultra Low Sulfur diesel fuel or No. 2 Ultra Low Sulfur climatized diesel fuels. Experience has shown that it also operates on No.
Page 352: Fuel Filler Cap (Gas Cap)
350 STARTING AND OPERATING WARNING! A fire may result if fuel is pumped into a portable container that is on a truck bed. You could be burned. Always place fuel containers on the ground while filling. Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door.
Page 353: Bulk Fuel Storage
You may try priming as described below. However, if the engine will not start, refer to the fuel priming procedure in the Service Manual or have the vehicle towed to an authorized Dodge dealer. WARNING! Do not open the high pressure fuel system with the engine running.
Page 354: Vehicle Loading
352 STARTING AND OPERATING 2. Crank the engine for 1 to 2 seconds. If the engine does not start, then release the key or starter button back to the RUN position (do not turn the key back to the OFF position).
Page 355 Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options and cargo. The label also specifies maximum capacities of front and rear axle systems (GAWR). Total load must be limited so GVWR and front and rear GAWR are not exceeded.
Page 356 354 STARTING AND OPERATING Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle. The front and rear curb weight values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added.
Page 357 An EXAMPLE of a loaded vehicle is shown in the following chart. Note that neither GVWR nor GAWR capabilities are exceeded. Overloading can cause poten- tial safety hazards and shorten service life. NOTE: The weights shown in this chart are not necessarily the weights for your vehicle.
Page 358: Trailer Towing
356 STARTING AND OPERATING TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer carefully re- view this information to tow your load as efficiently and safely as possible.
Page 359 Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR. WARNING! It is important that you do not exceed the maximum front or rear GAWR.
Page 360 358 STARTING AND OPERATING Weight-Distributing Hitch A weight-distributing system works by applying lever- age through spring (load) bars. They are typically used for heavier loads, to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer axle(s). When used in accordance with the manufacturers’...
Page 361 STARTING AND OPERATING 359 Weight-Distributing Hitch System Improper Adjustment Of Weight-Distributing System...
Page 362: Trailer Hitch Classification
360 STARTING AND OPERATING Fifth-Wheel Hitch A special high platform with a coupling that mounts over the rear axle of the tow vehicle in the truck bed. Connects a vehicle and fifth-wheel trailer with a coupling king pin. Gooseneck Hitch The gooseneck hitch employs a pivoted coupling arm which attaches to a ball mounted in the bed of a pickup truck.
Page 363: Trailer Towing Weights (Maximum Trailer Weight Ratings)
• http:// www.dodge.com/towing. • http:// www.dodge.ca (Canada). Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle.
Page 364: Towing Requirements
362 STARTING AND OPERATING • The weight of any other type of cargo or equipment put in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle.
Page 365 WARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.
Page 366 364 STARTING AND OPERATING 2. GTW 3. GAWR 4. Tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve the 10% to 15% range of tongue weight as a percentage of total trailer weight). Towing Requirements —...
Page 367 − An electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required. − Trailer brakes are recommended for trailers over 1,000 lbs (454 kg) and required for trailers in excess of 2,000 lbs (907 kg).
Page 368 366 STARTING AND OPERATING The Trailer Tow Package may include a 4 and 7 pin wiring harness. Use a factory approved trailer harness and connector. NOTE: Do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector.
Page 369 7-Pin Connector STARTING AND OPERATING 367 WARNING! Any work done to the vehicles electrical system, or wiring, should be performed by a qualified automo- tive technician, if done improperly it may cause damage to the electrical system wiring and could result in serious or fatal injury.
Page 370: Towing Tips
368 STARTING AND OPERATING Trailer Tow Additional Lamp Loads Output Maximum Functions Current Stop/Turn Left Stop/Turn Right Trailer Park Lamps Towing Tips Before setting out on a trip, practice turning, stopping Additional Bulbs and backing the trailer in an area away from heavy Allowed Example traffic.
Page 371 The automatic transmission fluid and filter should be changed if you REGULARLY tow a trailer for more than 45 minutes of continuous operation. See Maintenance Schedule in section 8 of this manual for transmission fluid change intervals. NOTE: Check the automatic transmission fluid level before towing.
Page 372: Trailer Towing Mirrors - If Equipped
370 STARTING AND OPERATING − refer to Cooling System Operating information in the Maintenance section of this manual for more informa- tion. Trailer Towing Mirrors — If Equipped These mirrors are designed with an adjustable mirror head to provide a greater vision range when towing extra-wide loads.
Page 373: Snowplow
/ installer obtain and STARTING AND OPERATING 371 follow the recommendations contained within the cur- rent Dodge BODY BUILDER’S GUIDE. See your dealer, installer or snowplow manufacture for this information. There are unique electrical systems that must be con- nected to properly assure operator safety and prevent overloading vehicle systems.
Page 374: Before Plowing
• Check that snowplow lighting is connected and func- tioning properly. Snowplow Prep Package Model Availability For Information about snowplow applications visit www.dodge.com or refer to the current Dodge Body Builders Guide. 1. The maximum number of occupants in the truck should not exceed two.
Page 375: Over The Road Operation With Snowplow Attached
of the plow. Front end tow-in should be checked and reset if necessary at the beginning and end of the snowplow season. This will help prevent uneven tire wear. The blade should be lowered whenever the vehicle is parked. Maintain and operate your vehicle and snowplow equip- ment following the recommendations provided by the specific snowplow manufacturer.
Page 376: General Maintenance
374 STARTING AND OPERATING NOTE: During snowplow usage on vehicles equipped with an overhead console module, the outside tempera- ture display will show higher temperatures than the outside ambient temperature. The higher displayed tem- perature is due to blocked or reduced airflow to the underhood ambient temperature sensor by the snow- plow.
Page 377 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) CAUTION! Front or rear wheel lifts should not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when recreational towing. Recreational Towing – 2-Wheel Drive Models Recreational towing of 2-Wheel Drive models is not allowed.
Page 378 376 STARTING AND OPERATING Recreational Towing Procedure — Manual Shift Transfer Case — If Equipped Use the following procedure to prepare your vehicle for recreational towing: CAUTION! It is necessary to follow these steps to be certain that the transfer case is fully in NEUTRAL before recre- ational towing to prevent damage to internal parts.
Page 379 CAUTION! Damage to the automatic transmission may occur if the transmission is shifted into PARK with the trans- fer case in NEUTRAL and the engine running. With the transfer case in NEUTRAL ensure that the engine is OFF prior to shifting the transmission into PARK. Returning to Normal Operation —...
Page 380 378 STARTING AND OPERATING CAUTION! • Do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. • Do not disconnect the rear driveshaft because fluid will leak from the transfer case and damage the internal parts.
Page 381 7. After shift is completed and the NEUTRAL light comes on, release the NEUTRAL button. 8. Start engine. 9. Shift automatic transmission into REVERSE. 10. Release brake pedal for five seconds and ensure that there is no vehicle movement. 11. Repeat steps 9 and 10 with the transmission in DRIVE.
Page 382 380 STARTING AND OPERATING CAUTION! Damage to the transmission may occur if the trans- mission is shifted into PARK with the transfer case in NEUTRAL and the engine running. With the transfer case in NEUTRAL ensure, that the engine is OFF prior to shifting the transmission into PARK.
Page 383 NOTE: Steps 1 through 5 are requirements that must be met prior to depressing the transfer case Neutral (N) button, and must continue to be met until one second elapses and the shift has been completed. If any of these requirements (with the exception of step 3 - key ON) are not met prior to depressing the Neutral (N) button, or are no longer met during the one second time, then all of the...
Page 384 382 STARTING AND OPERATING WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the NEUTRAL position without first fully engaging the parking brake. The transfer case NEUTRAL position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move despite the transmission position.
Page 385: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....384 Jacking And Tire Changing ....385 All Models –...
Page 386: Hazard Warning Flasher
384 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The Hazard Warning switch is mounted on the top of the steering column as shown in the illustration. Hazard Light Warning Switch To engage the Hazard Warning lights, depress the button on the top of the steering column.
Page 387: Jacking And Tire Changing
JACKING AND TIRE CHANGING WARNING! • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack.
Page 388: Jacking Instructions
386 WHAT TO DO IN EMERGENCIES WARNING! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience, abrupt stopping, rapid accelera- tion, or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury.
Page 389: Tire Changing Procedure
NOTE: The winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch. Tire Changing Procedure WARNING! Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you.
Page 390 388 WHAT TO DO IN EMERGENCIES • Turn on the Hazard Warning Flasher. • Block both the front and rear of the wheel diagonally oppo- site the jacking position. For example, if the right front wheel is being changed, block the left rear wheel.
Page 391 1. Remove the spare wheel, jack, and tools from storage. 2. Using the wheel wrench, loosen, but do not remove, the wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground. 3. For 2500/3500 4x2 series trucks, when changing a front wheel, place the bottle jack under the frame rail behind the wheel.
Page 392 390 WHAT TO DO IN EMERGENCIES NOTE: If the jack will not lower by turning the dial (thumbwheel) by hand, it may be necessary to use the jack drive tube in order to lower the jack. 4X2 Jacking...
Page 393 4. By rotating the wheel wrench clockwise, raise the vehicle until the wheel just clears the surface. WHAT TO DO IN EMERGENCIES 391 WARNING! Raising the vehicle higher than necessary can make the vehicle unstable and cause an accident. It could slip off the jack and hurt someone near it.
Page 394 392 WHAT TO DO IN EMERGENCIES 6. Using the wheel wrench, finish tightening the nuts using a crisscross pattern. Correct nut tightness is 135 ft. lbs. (183 N·m) torque for 2500/3500 single rear wheel (SRW) models and 145 ft. lbs. (197 N·m) for 3500 dual rear wheel models.
Page 395 On 3500 models with dual rear wheels (DRW), you must first remove the hub caps. The jack handle driver has a hook at one end that will fit in the pry off notch of the rear hub caps. Position the hook and pull out on the ratchet firmly.
Page 396 394 WHAT TO DO IN EMERGENCIES 8-Stud — Dual Rear Wheels Dual wheels are flat mounted, center piloted. The lug nuts are a two piece assembly. When the tires are being rotated or replaced, clean these lug nuts and add two drops of oil at the interface between the hex and the washer.
Page 397 WHAT TO DO IN EMERGENCIES 395 These dual rear wheels should be tightened as follows: 1. Tighten the wheel nuts in the numbered sequence to a snug fit. 2. Retighten the wheel nuts in the same sequence to the torques listed in the table. Go through the sequence a second time to verify that specific torque has been achieved.
Page 398: Hoisting
396 WHAT TO DO IN EMERGENCIES tightened to recommended torque. Tighten the nuts to final torque in increments. Progress around the bolt circle, tightening the nut opposite to the nut just previ- ously tightened until final torque is achieved. Recom- mended torques are shown in the following chart.
Page 399: Jump-Starting
JUMP-STARTING WARNING! To prevent personal injury or damage to clothing, do not allow battery fluid to contact eyes, skin or fabrics. Do not lean over a battery when connecting jumper cables or allow cable clamps to touch each other. Keep open flames or sparks away from battery vent holes.
Page 400 398 WHAT TO DO IN EMERGENCIES CAUTION! Use the Jump-Start Procedure only when the charge indicator (if equipped) in both batteries is dark in the center. Do not attempt jump-starting when either battery charge indicator (if equipped) is bright or yellow.
Page 401 2. Connect one end of the other jumper cable to negative (-) post of booster battery. Connect the other end of the jumper cable to a good ground on the engine block of the vehicle with the discharged battery. Make sure a good connection is made, free of dirt and grease.
Page 402: With Portable Starting Unit
400 WHAT TO DO IN EMERGENCIES WARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; 3. Damage to charging system of booster vehicle or of immobilized vehicle.
Page 403: Emergency Tow Hooks - If Equipped
In general, the least amount of accelerator pedal pressure to maintain the rocking motion without spinning the wheels or racing the engine, is most effective. Racing the engine or spinning the wheels, due to the frustration of not freeing the vehicle, may lead to transmission over- heating and failure.
Page 404: Towing A Disabled Vehicle
402 WHAT TO DO IN EMERGENCIES CAUTION! Tow hooks are for emergency use only, to rescue a vehicle stranded off-road. Do not use tow hooks for tow truck hookup or highway towing. You could damage your vehicle. TOWING A DISABLED VEHICLE Proper towing or lifting equipment is required to prevent damage to your vehicle.
Page 405: 2-Wheel Drive Vehicles
2–Wheel Drive Vehicles Provided that the transmission is operable, tow with the transmission in NEUTRAL and the ignition key in the OFF position along with the front wheels raised and the rear wheels on the ground. Speed must not exceed 30 mph (50 km/h) and distance must not exceed 15 mi (25 km).
Page 407: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS Engine Compartment — 6.7L Diesel Engine ..408 Onboard Diagnostic System (OBD II) ..409 Replacement Parts ..... . 409 Engine Data Plate .
Page 408 406 MAINTAINING YOUR VEHICLE Front Suspension Ball Joints ....431 Steering Linkage — Inspection ... . 432 Front Prop Shaft Lubrication .
Page 409 Vehicle Storage ......464 Replacement Light Bulbs ....465 Bulb Replacement .
Page 410: Engine Compartment - 6.7L Diesel Engine
408 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 6.7L DIESEL ENGINE...
Page 411: Onboard Diagnostic System (Obd Ii)
ONBOARD DIAGNOSTIC SYSTEM (OBD II) Vehicles equipped with California emissions controls have a sophisticated onboard diagnostic system called OBDII. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
Page 412: Engine Data Plate
410 MAINTAINING YOUR VEHICLE ENGINE DATA PLATE Use the information from the engine data plate when discussing service or sourcing parts for your engine. The engine data plate is located on the intake side of the breather cover. AUTHORIZED DEALER SERVICE Your authorized dealer has the qualified service person- nel, special tools and equipment to perform all service operations in an expert manner.
Page 413 CAUTION! To maintain your vehicle safely follow these guide- lines: • Watch your vehicle’s mileage and check your Maintenance Schedules regularly for required ser- vicing. Excessive wear or damage to certain vehicle components can result if required services are not performed.
Page 414: Maintenance Procedures
412 MAINTAINING YOUR VEHICLE WARNING! To maintain your vehicle safely and avoid personal injury, follow these guidelines: • Never spray or pour diesel fuel, flammable liquid or starting fluids (ether) into the air cleaner assembly, air intake piping or turbocharger inlet in an attempt to start the vehicle, unintended engine acceleration may occur.
Page 415: Engine Oil
Engine Oil Checking Oil Level To assure proper lubrication of your vehicle’s engine, the engine oil must be maintained at the correct level. Check the oil level at regular intervals. The best time to check the oil level is before starting the engine after it has been parked overnight.
Page 416 414 MAINTAINING YOUR VEHICLE Never operate the engine with oil level below the “ADD” mark or above the upper “SAFE” mark. Change Engine Oil (6.7L Diesel Engine) Follow the 6.7L Diesel Maintenance Schedule for recom- mended engine oil change intervals. Engine Oil Selection (6.7L Diesel Engines) For best performance and maximum protection under all types of operating conditions, the manufacturer only...
Page 417 Engine Oil Viscosity (SAE Grade) 15W-40 Engine DaimlerChrysler Materials Standard MS-10902 and the API CJ-4 engine oil category. Engine oil not designated by the DaimlerChrysler or Cummins Material Standards and API CJ-4 should not be used, engine and exhaust system durability may be compromised.
Page 418 416 MAINTAINING YOUR VEHICLE Engine Oil Filter Refer to Fluids, Lubricants and Genuine Parts for the correct part number. The engine oil filter should be changed at every engine oil change. Engine Oil And Filter — Change Operate the engine until the coolant temperature reaches 140°F (60°C).
Page 419 CAUTION! Fill the oil filter element with clean oil before instal- lation. Use the same type oil that will be used in the engine. When filling the oil filter, prevent foreign material from falling into the filter. Severe engine damage may occur. Apply a light film of lubricating oil to the sealing surface of the filter gasket before installing the filter.
Page 420: Drive Belt
418 MAINTAINING YOUR VEHICLE Start the engine and operate it at idle for several minutes. Check for leaks at the lubricating oil filter and oil pan drain plug. Run the engine until it has reached operating tempera- ture, stop the engine. Wait approximately 15 minutes to let the oil in the upper parts of the engine drain back to the pan.
Page 421: Engine Air Cleaner Filter (6.7L Diesel Engines)
Engine Air Cleaner Filter (6.7L Diesel Engines) CAUTION! All air entering the engine intake must be filtered. The abrasive particles in unfiltered air will cause rapid wear to engine components. The condition of the air cleaner filter is monitored by the Engine Control Module.
Page 422 420 MAINTAINING YOUR VEHICLE If the vehicle experiences a sudden loss of engine power when being driven in heavy snow, rain or when plowing snow, and the EVIC message center states SERVICE AIR FILTER or the Filter Minder™ (if equipped) is showing a plugged filter, then visually inspect the air filter for snow/ice build up or extreme water saturation.
Page 423 The clear plastic housing on the Filter Minder™ (If Equipped), allows you to view the amount of air pressure drop across the filter element. It consists of a diaphragm and a calibrated spring sealed inside the plastic housing. As the air cleaner filter becomes clogged and air pressure drop across the filter element increases, a yellow disc travels along a graduated scale on the side of the Filter Minder™.
Page 424: Draining Fuel/Water Separator Filter (6.7L Diesel Engine)
422 MAINTAINING YOUR VEHICLE Draining Fuel/Water Separator Filter (6.7L Diesel Engine) CAUTION! Do not drain the fuel/water separator filter when the engine is running. CAUTION! Do not prefill the fuel filter when installing a new fuel filter. There is a possibility that debris could be introduced into the fuel filter during this action.
Page 425 If the WATER IN FUEL LIGHT comes on and a single chime is heard while you are driving, or with the key in the ON position, there may be a problem with your water separator wiring or sensor. See your authorized dealer for service.
Page 426 424 MAINTAINING YOUR VEHICLE WARNING! Do not open the high pressure fuel system with the engine running. Engine operation causes high fuel pressure. High pressure fuel spray can cause serious injury or death. Priming if the engine has run out of fuel 1.
Page 427: Message Process Flow (Catalyst Full Message)
WARNING! Do not use alcohol or gasoline as a fuel blending agent. They can be unstable under certain conditions and be hazardous or explosive when mixed with diesel fuel. CAUTION! Due to lack of lubricants in alcohol or gasoline, the use of these fuels can cause damage to the fuel system.
Page 428 426 MAINTAINING YOUR VEHICLE To achieve these emission standards, your vehicle is equipped with a state of the art engine and exhaust system. The engine and exhaust aftertreatment system work together to achieve the EPA Heavy Duty Diesel Engine Emissions Standards. These systems are seam- lessly integrated into your vehicle and managed by the Cummins 6.7L engine Powertrain Control Module...
Page 429 located on the top of the engine valve cover. For addi- tional information, see your local authorized dealer. Catalyst Full See Owner Manual “Catalyst Full See Owner Manual” will be displayed on the overhead console of your vehicle if the exhaust particulate filter reaches 80% of its maximum storage capacity.
Page 430: Maintenance Free Batteries
428 MAINTAINING YOUR VEHICLE CATALYST FULL SERVICE REQD If the particulate filter reaches 99% of its capacity, the overhead console in your vehicle will chime twice and display the message CATALYST FULL SERVICE REQD. At this point the engine PCM will register a fault code, the instrument panel will display a MIL light and the engine PCM will derate the truck, reducing its horse- power and torque output.
Page 431 WARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water.
Page 432: Air Conditioner Maintenance
430 MAINTAINING YOUR VEHICLE Battery Blanket Usage A battery loses 60% of its cranking power as the battery temperature decreases to 0°F (-18°C). For the same de- crease in temperature, the engine requires twice as much power to crank at the same RPM. The use of 120 VAC powered battery blankets will greatly increase starting capability at low temperatures.
Page 433: Power Steering - Fluid Check
NOTE: Use only manufacturer approved A/C System Sealers, Stop Leak Products, Seal Conditioners, Compres- sor Oil, or Refrigerants. Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar- bon (HFC) that is endorsed by the Environmental Pro- tection Agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment.
Page 434: Steering Linkage - Inspection
432 MAINTAINING YOUR VEHICLE Steering Linkage — Inspection Whenever the vehicle is hoisted all steering linkage joints should be inspected for evidence of damage. If seals are damaged, parts should be replaced to prevent leakage or contamination of the grease. Front Prop Shaft Lubrication Lubricate the front driveshaft grease fitting at each oil change listed in the appropriate maintenance schedule...
Page 435: Body Lubrication
Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors, liftgate, tailgate, sliding doors and hood hinges should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear. Prior to the application of any lubricant, the parts concerned should be wiped clean to remove dust and grit.
Page 436: Windshield Washers
434 MAINTAINING YOUR VEHICLE Windshield Washers The fluid reservoir is located under the hood and should be checked for fluid level at regular intervals. Fill the reservoir with windshield washer solvent only (not ra- diator antifreeze). When refilling the washer fluid reser- voir, take some washer fluid and apply it to a cloth or towel and wipe the wiper blades clean.
Page 437: Exhaust System
Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken,...
Page 438: Cooling System
436 MAINTAINING YOUR VEHICLE Cooling System WARNING! You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, don’t open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator is hot.
Page 439 Coolant bottle level check The coolant reserve system provides a quick visual method of determining that the coolant level is adequate. With the engine idling and warmed to the normal operating temperature, the level of the coolant on the coolant bottle should be between the fluid level marks. Check the coolant level whenever the hood is raised.
Page 440 438 MAINTAINING YOUR VEHICLE CAUTION! The manufacturer highly recommends that all cool- ing system service, maintenance, and repairs be per- formed by your local authorized dealer. If the solution is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner.
Page 441 Adding Coolant Your vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This coolant can be used up to 5 Years or 100,000 miles (160 000 km) before replacement. To prevent reducing this extended maintenance period, it is important that you use the same coolant throughout the life of your vehicle.
Page 442 440 MAINTAINING YOUR VEHICLE The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety pre- caution.
Page 443 The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for coolant freeze point or replacing coolant. Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month.
Page 444: Fan
442 MAINTAINING YOUR VEHICLE • Make sure that the radiator and coolant recovery bottle overflow hoses are not kinked or obstructed. • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean also.
Page 445: Hoses And Vacuum/Vapor Harnesses
To guarantee optimum performance of the system, keep the surfaces of the charge air cooler, condenser and radiator clean and free of debris. Periodically check the hoses leading to and from the charge air cooler for cracks or loose clamps resulting in loss of pressure and reduced engine performance.
Page 446 444 MAINTAINING YOUR VEHICLE Brake Master Cylinder The fluid level of the master cylinder should be checked when performing under the hood service, or immedi- ately if the brake system warning lamp indicates system failure. The brake master cylinder has a translucent plastic reservoir.
Page 447: Clutch Linkage
WARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter or moisture.
Page 448: Rear Axle And 4X4 Front Driving Axle Fluid Level
446 MAINTAINING YOUR VEHICLE Rear Axle And 4x4 Front Driving Axle Fluid Level For Model 9.25 Front Axles and 10.5”/11.5” Rear Axles refer to Fluids, Lubricants and Genuine Parts for the correct lubricant type. For normal service, periodic fluid level checks are not required. When the vehicle is ser- viced for other reasons, the exterior surfaces of the axle assembly should be inspected.
Page 449: Manual Transmission - If Equipped
Drain And Refill Follow the Maintenance Schedule for recommended transfer case fluid change intervals. Lubricant Selection Refer to Fluids, Lubricants and Genuine Parts for the correct lubricant type. Manual Transmission — If Equipped Fluid Level Check This fluid level can be checked by removing the filler plug.
Page 450 448 MAINTAINING YOUR VEHICLE CAUTION! Using a transmission fluid other than the manufac- turers recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturers recommended fluid will result in more frequent fluid and filter changes.
Page 451 5. Remove the dipstick, wipe it clean and reinsert it until seated. 6. Remove the dipstick again and note the fluid level on both sides. The fluid level should be between the “HOT” (upper) reference holes on the dipstick at normal operat- ing temperature.
Page 452: Front Wheel Bearings
450 MAINTAINING YOUR VEHICLE Automatic Transmission Fluid and Filter Change To obtain best performance and long life for automatic transmissions, the manufacturer recommends that they be given regular maintenance service by an authorized dealer or Service Center. It is important that the trans- mission fluid is maintained at the correct level, and that it is drained and refilled as specified.
Page 453: Noise Control System Required Maintenance & Warranty
MAINTAINING YOUR VEHICLE Rear Wheel Bearings Clean and repack when brake linings are replaced or rotors resurfaced. Noise Control System Required Maintenance & Warranty For 3500 Two-Wheel Drive and Four-Wheel Drive mod- els over 10,000 lbs. (4 535 kg) Gross Vehicle Weight Rating.
Page 454 452 MAINTAINING YOUR VEHICLE Required Maintenance For Noise Control Systems The following maintenance services must be performed every 6 months or 6,000 miles (9 600 km), whichever comes first, to assure proper operation of the noise control systems. In addition, inspection and service should be performed anytime a malfunction is observed or suspected.
Page 455 Among those acts presumed to constitute tampering are the acts listed below. • AIR CLEANER − Removal of the air cleaner. − Removal of the air cleaner filter element from the air cleaner housing. − Removal of the air ducting. •...
Page 456 454 MAINTAINING YOUR VEHICLE Maintenance Log and Service Chart (Diesel Engines) Noise Systems Maintenance Chart and Service Log — Insert Month, Day, Year under column mileage closest to the mileage at which service was performed. MILES KILOMETERS Exhaust system-inspect Air cleaner assembly-inspect ODOMETER READING PERFORMED BY PERFORMED AT...
Page 457: Appearance Care And Protection From Corrosion
Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.
Page 458 456 MAINTAINING YOUR VEHICLE • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder which will scratch metal and painted surfaces.
Page 459 Wheel and Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome plated wheels should be cleaned regularly with a mild soap and water to prevent corrosion. To remove heavy soil, use Mopar Wheel Cleaner or select a non- abrasive, non-acidic cleaner.
Page 460 458 MAINTAINING YOUR VEHICLE Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and Mopar Total Clean.
Page 461: Fuses (Integrated Power Module)
1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners.
Page 462 460 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 20 Amp Yellow 20 Amp Yellow — 15 Amp Blue 20 Amp Yellow 10 Amp — 10 Amp Description Cavity Cartridge Power Outlet Console Cabin Compartment Node (CCN) Door Locks — Aisin Transmission Controls (Diesel Only) Power Sunroof...
Page 463 Cavity Cartridge Mini Fuse Fuse 30 Amp Electric Brake Pink 25 Amp Power-Battery Natural RWAL/ABS Module Feed 15 Amp Park Lights Left Blue 20 Amp Trailer Park Lights Yellow 15 Amp Park Lights Right Blue — — 40 Amp ABS Pump Green 30 Amp Trailer Tow Battery...
Page 464 462 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 40 Amp Green 10 Amp 10 Amp 15 Amp Blue 10 Amp Description Cavity Cartridge Power Seats Power Run/Start- PCM/Steering Angle Sensor 4X4 Switch/Pass Dr Switch/EC Mirror Power Run/Start- ABS/RWAL/Smart Bar/YAW Sensor/ Universal Exhaust Gas Oxygen (Uego) Sensor Controller...
Page 465 Cavity Cartridge Mini Fuse Fuse 10 Amp Seatbelt Tension Reducer/Power IGN Run/Acc 20 Amp Power IGN Run/Acc Yellow — Cigar Lighter/Rear Power Point — — 30 Amp Diesel PCM (Diesel Pink Only) Description • When installing the Integrated Power Module cover, it is important to ensure the cover is prop- erly positioned and fully latched.
Page 466: Vehicle Storage
464 MAINTAINING YOUR VEHICLE VEHICLE STORAGE If you are storing your vehicle for more than 21 days, we recommend that you take the following steps to mini- mize the drain on your vehicle’s battery: • Disconnect the Ignition-Off Draw fuse (IOD) fuse located in the Integrated Power Module, located in the engine compartment.
Page 467: Replacement Light Bulbs
REPLACEMENT LIGHT BULBS LIGHT BULBS — Inside Overhead Console Lights ....TS 212-2 Dome Light......7679 All of the inside bulbs are brass or glass wedge base.
Page 468: Bulb Replacement
466 MAINTAINING YOUR VEHICLE BULB REPLACEMENT Headlight (Halogen)/Front Park and Turn Lights CAUTION! This is a halogen bulb. Avoid touching the glass with your fingers. Reduced bulb life will result. 1. Open the hood 2. Remove the two bolts from the front of the headlight housing.
Page 469 3. Remove the plug from the inner fender well and remove the nut through the access hole. Inner Fender Plug MAINTAINING YOUR VEHICLE Rear Headlight Housing Nut Access 4. Pull the housing out from the fender to allow room to disconnect the electrical connectors.
Page 470 468 MAINTAINING YOUR VEHICLE NOTE: For easier removal, pull the headlight assembly straight forward, applying the greatest amount of force to the outer edge of the headlight assembly. Headlight Removal Bulb Removal 5. Unlock and pull connector straight from the base of the headlight halogen bulb.
Page 471: Fog Lights
6. Twist connector on the side marker/turn signal/park light bulb ⁄ turn and remove connector and bulb from housing. 7. Remove housing from vehicle with headlight halogen bulb in housing. 8. Twist the headlight halogen bulb headlight bulb from the housing. 9.
Page 472: Tail, Stop, Turn And Backup Lights
470 MAINTAINING YOUR VEHICLE 2. Pull bulb straight from the connector. 3. Reverse procedure for installation of bulbs and hous- ing. Tail, Stop, Turn and Backup Lights 1. Remove the two screws that pass through the bed sheetmetal. Removing The Two Screws...
Page 473 2. Pull the housing straight out from the body, with a quick motion, to separate the housing from the body. If not pulled straight, locators may be damaged. Pulling Housing From Body MAINTAINING YOUR VEHICLE 3. Rotate the bulb socket counterclockwise to remove from the housing.
Page 474 472 MAINTAINING YOUR VEHICLE 4. Pull bulb straight out of socket. Pulling Bulb From Socket 5. Reverse Procedure to install bulb and housing. Place the two raised blocks past the body. Sliding Raised Blocks Past Body...
Page 475: Center High-Mounted Stoplight (Chmsl) With Cargo Light
Center High-Mounted Stoplight (CHMSL) With Cargo Light 1. Remove the two screws holding the housing/lens to the body as shown. MAINTAINING YOUR VEHICLE 2. Separate the connector holding the housing and wir- ing harness to the body. 3. Turn desired bulb socket ⁄...
Page 476: Cab Top Clearance Lights - If Equipped
474 MAINTAINING YOUR VEHICLE 4. Pull desired bulb straight from the socket. • Outside Bulbs: Cargo Lights • Inside Bulb: Center High-Mounted Stop Light 5. Reverse procedure for installation of bulbs and hous- ing. Cab Top Clearance Lights — If Equipped 1.
Page 477 MAINTAINING YOUR VEHICLE 2. Rotate the socket ⁄ turn and pull it from the light 3. Pull the bulb straight from it’s socket and replace. assembly.
Page 478: Tailgate Id Lights (Dual Rear Wheels) - If Equipped
476 MAINTAINING YOUR VEHICLE Tailgate ID Lights (Dual Rear Wheels) — If Equipped 1. Remove the two screws and housing and access the bulb sockets from the rear. 2. Turn socket ⁄ turn counterclockwise to access the bulb.
Page 479: Rear Light Bar Id Marker (Dual Rear Wheel) - If Equipped
3. Pull bulb straight out from socket. 4. Reverse procedure for installation of bulbs and hous- ing. MAINTAINING YOUR VEHICLE Rear Light Bar ID Marker (Dual Rear Wheel) — If Equipped 1. Loosen the two screws and the housing to gain access to the bulb sockets.
Page 480: Side Marker Lights (Dual Rear Wheels)
478 MAINTAINING YOUR VEHICLE 3. Pull the bulb straight out from the socket. 4. Reverse procedure for installation of bulbs and hous- ing. Side Marker Lights (Dual Rear Wheels) 1. Push rearward on the side marker light assembly. 2. Pull the entire assembly from the fender. 3.
Page 481: Fluid Capacities
FLUID CAPACITIES FLUID CAPACITIES U.S. Fuel 2500 Shortbed Models 34 gal 2500 Longbed Models 35 gal 3500 Shortbed Models 34 gal 3500 Longbed Models 35 gal FLUID CAPACITIES Metric Engine Oil 6.7L HO Turbo Diesel Engine I-6 (SAE 15W-40, 128L API CJ-4 Certified, that 132L meets CES 20081 Stan-...
Page 482: Fluids, Lubricants And Genuine Parts
480 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil (6.7L Turbo Diesel) Engine Oil Filter (6.7L Turbo Diesel Engine) Engine Fuel Filter (6.7L Turbo Diesel Engine) Crankcase Ventilation Filter (6.7L Turbo Diesel Engine) Fluids, Lubricants and Genuine Parts Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology).
Page 483 Component Fuel Selection (6.7L Turbo Diesel Engine) Fluids, Lubricants and Genuine Parts Use good quality diesel fuel from a reputable supplier in your vehicle. Fed- eral law requires that you must fuel this vehicle with Ultra Low Sulfur High- way Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sul- fur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.
Page 484: Chassis
482 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Transfer Case Manual Transmission Fluid G-56 Clutch Linkage Front and Rear Axle Fluid 2500/3500 Models Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts. Mopar ATF+4, Automatic Transmission Fluid. Mopar ATF+4, Automatic Transmission Fluid. Mopar ATF+4, Automatic Transmission Fluid.
Page 485: Maintenance Schedules
MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..484 Maintenance Schedules — 6.7L Turbo Diesel ..484 Oil Change Indicator System ... . . 486 Perform Service Indicator .
Page 486: Emission Control System Maintenance
484 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The Scheduled maintenance services, listed in bold type in this section (Section 8) must be done at the times or mileages specified to assure the continued proper func- tioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
Page 487 take some washer fluid and apply it to a cloth or towel and wipe clean the wiper blades, this will help blade performance. Once a Month • Check tire pressure and look for unusual wear or damage. • Inspect the batteries and clean and tighten the termi- nals as required.
Page 488: Perform Service Indicator
486 MAINTENANCE SCHEDULES Oil Change Indicator System Your vehicle is equipped with an engine oil change indicator system. This system will alert you when it is time to change your engine oil by displaying the words “Oil Change Required” on your Electronic Vehicle Infor- mation Center (EVIC).
Page 489: Maintenance Schedule
Maintenance Schedule (Miles) Kilometers [Months] Change engine oil and engine oil filter. (Under no cir- cumstances should oil change intervals exceed 12 000 km (7,500 mi) or 6 months, which ever comes first). Lubricate Front Drive Shaft Fitting (4X4). Rotate tires. Lubricate outer tie rod ends.
Page 490 488 MAINTENANCE SCHEDULES (Miles) Kilometers [Months] Change engine oil and engine oil filter. Lubricate Front Drive Shaft Fitting (4X4). Rotate tires. Lubricate outer tie rod ends. Change the transfer case fluid (4X4). Change front and rear axle fluid (4X4). Change the automatic transmission fluid & filter if using your vehicle for any of the following: police, taxi, fleet or frequent trailer towing.
Page 491 (Miles) Kilometers [Months] Inspect the brake linings, replace if necessary. Inspect and adjust parking brake if necessary. Inspect front wheel bearings. Replace Crankcase Ventilation Filter (CCV). Clean EGR Valve**. Clean EGR Cooler**. MAINTENANCE SCHEDULES 489 (45,000) (52,500) (60,000) 72 000 84 000 97 000 [36]...
Page 492 490 MAINTENANCE SCHEDULES (Miles) Kilometers [Months] Change engine oil and engine oil filter. Lubricate Front Drive Shaft Fitting (4X4). Rotate tires. Lubricate outer tie rod ends. Flush and replace engine coolant, if not replaced at 60 mos.*** Inspect the transfer case fluid (4X4). Change front and rear axle fluid (4X4).
Page 493 (Miles) Kilometers [Months] Change engine oil and engine oil filter. Lubricate Front Drive Shaft Fitting (4X4). Rotate tires. Lubricate outer tie rod ends. Flush and replace engine coolant at 120 months, if not replaced at 100,000 miles (161 000 km).*** Inspect drive belt, replace as required.* Change transfer case fluid (4X4).
Page 494 492 MAINTENANCE SCHEDULES (Miles) Kilometers [Months] Inspect the brake linings, replace if necessary. Inspect and adjust parking brake if necessary. Adjust valve lash clearance. Replace Crankcase Ventilation Filter (CCV). Clean the EGR Valve. Clean the EGR Cooler. Inspection and service should also be performed anytime a malfunction is observed or suspected.
Page 495 CAUTION! ***The manufacturer highly recommends that all cooling system service, maintenance, and repairs be performed by your local authorized dealer. MAINTENANCE SCHEDULES 493 WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment.
Page 497: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......497 Prepare For The Appointment .
Page 498 496 IF YOU NEED CONSUMER ASSISTANCE Publication Order Forms ....501 Department Of Transportation Uniform Tire Quality Grades ......503 Treadwear .
Page 499: Suggestions For Obtaining Service For Your Vehicle
SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty.
Page 500: Daimlerchrysler Motors Corporation Customer Center
498 IF YOU NEED CONSUMER ASSISTANCE special tools, and the latest information to ensure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your authorized dealer’s service manager first. Most matters can be re- solved with this process.
Page 501: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommuni- cation Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
Page 502: Warranty Information (U.s. Vehicles Only)
500 IF YOU NEED CONSUMER ASSISTANCE WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain prod- ucts of component wear contain, or emit, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Page 503: In Canada
To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), or go to http://www.safercar.gov; or write to: Administra- tor, NHTSA, 400 Seventh Street, SW., Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from http://www.safercar.gov.
Page 504 502 IF YOU NEED CONSUMER ASSISTANCE • Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with dia- grams, charts and detailed illustrations. These practi- cal manuals make it easy for students and technicians to find and fix problems on computer-controlled ve- hicle systems and features.
Page 505 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle.
Page 506 504 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.
Page 507 INDEX...
Page 508 506 INDEX Adding Fuel ......349 Adjustable Pedals ..... . . 138 Air Cleaner, Engine (Engine Air Cleaner Filter) .
Page 509 Shifting ......285 Special Additives ..... . 450 Autostick .
Page 510 508 INDEX Radiator (Coolant Pressure) ....439 Car Washes ......455 Carbon Monoxide Warning .
Page 511 Drain, Flush, and Refill ....437 Inspection ......440 Points to Remember .
Page 512 510 INDEX Electric Rear Window Defrost ... . . 87,173 Electrical Power Outlets ....160 Electronic Range Select (ERS) .
Page 513 Fan ........442 Filters Closed Crankcase Ventilation (CCV) ..426 Engine Oil .
Page 514 512 INDEX Voltmeter ......189,275 Gear Ranges ......285,292 General Information .
Page 515 Illuminated Entry ......20 Immobilizer (Sentry Key) ....15 Infant Restraint .
Page 516 514 INDEX Bulb Replacement ....465,466 Cap Top Clearance ..... 474 Cargo .
Page 517 Power Door ......27 Steering Wheel ......18 Lower Anchors and Tether for CHildren (LATCH) .
Page 518 516 INDEX Trip ......192,199 Off-Pavement Driving (Off-Road) ... . 309 Off-Road Driving (Off-Pavement) .
Page 519 Placard, Tire and Loading Information ..320 Power Distribution Center (Fuses) ....459 Door Locks ......27 Mirrors .
Page 520 518 INDEX Remote Keyless Entry (RKE) ....21 Remote Sound System (Radio) Controls ..246 Replacement Keys ......16 Replacement Tires .
Page 521 Reclining ......117 Reclining Rear ......121 Security Alarm (Theft Alarm) .
Page 522 520 INDEX Starting Procedures ..... . 268 Starting Procedures (Diesel Engines) ..268 Steering Linkage .
Page 523 Inflation Pressures ..... 325 Jacking ......387 Life of Tires .
Page 524 522 INDEX Trailer Towing Guide ..... 361 Trailer Weight ......361 Transaxle Automatic .
Page 525 Warning Lights (Instrument Cluster Description) ......189 Warnings and Cautions ..... 7 Warranty Information .
Page 526 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
Page 527 81-326-0828 Second Edition Printed in U.S.A.

This manual is also suitable for:

2008 dr ram 2008 dr/dh ram 2008 ram 1500 2008 ram 2500 2008 ram 4500 2008 ram 5500 ... Show all

Dodge 2008 DH Ram Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

150 Understanding the Features of Your Vehicle

Understanding the Features of Your Vehicle 159

174 Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

Quick Links

Chapters

Related Manuals for Dodge 2008 DH Ram

Summary of Contents for Dodge 2008 DH Ram