Page 1 Avenger 2 0 0 8 O W N E R ’ S M A N U A L...
Page 2 VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents.
Page 3: Introduction 3
TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 5 CONTENTS Introduction ......4 How To Use This Manual ....4 Warnings And Cautions .
Page 6: Introduction
4 INTRODUCTION INTRODUCTION This Owner’s Manual has been prepared with the assis- tance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully.
Page 7 INTRODUCTION 5...
Page 8: Warnings And Cautions
6 INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual you may miss important infor- mation.
Page 9: Vehicle Modifications/Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 11: Table Of Contents
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Ignition Key Removal ....12 Key-In-Ignition Reminder .
Page 12 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Using The Express Down Windows Feature — If Equipped ......25 Using The Panic Alarm .
Page 13 Seat Belt Pretensioners ....48 Enhanced Seat Belt Reminder System (BeltAlert ) ......48 BeltAlert Programming .
Page 14: Things To Know Before Starting Your Vehicle 9
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place.
Page 15 NOTE: • If you try to remove the key before you place the selector lever in PARK, the key may become trapped temporarily in the ignition switch lock cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described.
Page 16: Key-In-Ignition Reminder
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! An unlocked car is an invitation to thieves. Always remove key from the ignition and lock all doors when leaving the vehicle unattended. KEY-IN-IGNITION REMINDER Opening the driver’s door when the key is in the ignition, sounds a signal to remind you to remove the key.
Page 17 the vehicle. The system will shut the engine off in two seconds if someone uses an invalid key to try to start the engine. NOTE: A key that has not been programmed is also considered an invalid key, even if it is cut to fit the ignition switch lock cylinder for that vehicle.
Page 18: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Replacement Keys NOTE: Only keys that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a Sentry Key is programmed to a vehicle, it cannot be programmed to any other vehicle.
Page 19: General Information
3. Insert the second valid key into the ignition switch. Turn the ignition switch to the ON position within 15 seconds. After 10 seconds, a chime will sound. In addi- tion, the Vehicle Security Light will begin to flash. Turn the ignition switch to the LOCK position and remove the second key.
Page 20: Security Alarm System - If Equipped
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • This device must accept any interference that may be received, including interference that may cause undes- ired operation. SECURITY ALARM SYSTEM — IF EQUIPPED The Vehicle Security Alarm (VSA) system monitors the doors and trunk for unauthorized entry and ignition switch for unauthorized operation.
Page 21: To Disarm The System
will automatically disarm. After 16 seconds, the Vehicle Security Light will flash slowly. This shows that the system is fully armed. NOTE: • During the 16 second arming period, if a door is opened or the ignition switch is turned ON, the system will automatically disarm.
Page 22: Illuminated Entry System - If Equipped
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the alarm system is armed and the battery becomes disconnected the system will remain armed when the battery is reconnected. The exterior lights will flash, the horn will sound, and the ignition will not start the vehicle.
Page 23: Remote Keyless Entry - If Equipped
REMOTE KEYLESS ENTRY — IF EQUIPPED This system allows you to lock or unlock the doors, open the trunk, or activate the PANIC alarm from distances a maximum of 66 ft (20 m) using a hand-held radio transmitter. The transmitter need not be pointed at the vehicle to activate the system.
Page 24: To Unlock The Doors
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE TO UNLOCK THE DOORS Press and release the UNLOCK button on the transmitter once to unlock the driver’s door, or twice to unlock all doors. The turn signal lights will flash to acknowledge the unlock signal.
Page 25 Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm. Flash Lights With Lock The feature will cause the turn signal lights to flash when the doors are locked or unlocked with the transmitter. This feature can be turned on or turned off.
Page 26: To Lock The Doors
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Illuminated Approach — If Equipped This feature activates the headlights for up to 90 seconds when the doors are unlocked with the transmitter. The time for this feature is programmable on vehicles equipped with EVIC.
Page 27: To Unlatch The Trunk
NOTE: Pressing the LOCK button on the transmitter while you are in the vehicle will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm. TO UNLATCH THE TRUNK Press the TRUNK button on the transmitter two times to unlatch the trunk.
Page 28: Programming Additional Transmitters
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE PROGRAMMING ADDITIONAL TRANSMITTERS Refer to SENTRY KEY “Sentry Key Programming.” If you do not have a programmed transmitter, contact your authorized dealer for details. BATTERY REPLACEMENT The recommended replacement battery is CR2032. NOTE: Perchlorate Material —...
Page 29: General Information
GENERAL INFORMATION This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received including interference that may cause undesired operation.
Page 30: Remote Start System - If Equipped
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE START SYSTEM — IF EQUIPPED Remote start conveniently starts the engine from outside the vehicle by using the Remote Keyless Entry (RKE) key fob while maintaining security. The system has a targeted range of up to 328 ft (100 m).
Page 31: How To Use Remote Start
HOW TO USE REMOTE START All of the following conditions must be met before the engine will remote start: • Shift the gear selector lever into PARK. • Doors closed. • Hood closed. • Trunk closed. • Hazard switch off. •...
Page 32: Door Locks
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Exit Remote Start Mode And Drive The Vehicle Before the end of the 15-minute cycle, press and release the UNLOCK button on the RKE transmitter to unlock the doors and disarm the Vehicle Security Alarm (if equipped).
Page 33 WARNING! • For personal security, and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle.
Page 34: Power Door Locks
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE POWER DOOR LOCKS A door lock switch is located on the driver and passenger door panel. Press this switch to lock or unlock the doors. Power Door Lock Switch Automatic Door Locks — If Equipped The auto door lock feature can be enabled or disabled by your authorized dealer.
Page 35 Automatic Unlock Doors On Exit Programming The Auto Unlock on Exit feature can be enabled or disabled as follows: • For vehicles equipped with the Electronic Vehicle Information Center (EVIC), refer to “Personal Settings (Customer Programmable Features)” under “Elec- tronic Vehicle Information Center (EVIC)” in Section 4 of this manual for details.
Page 36: Child-Protection" Door Lock System (Rear Doors)
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE “CHILD-PROTECTION” DOOR LOCK SYSTEM (REAR DOORS) The Rear Door Child-Protection Locks are located inside the rear edge of the door. Insert the tip of the ignition key or similar flat-bladed object into the lock and rotate approximately one—quarter turn to the lock or unlock position (as indicated by the stamped icons).
Page 37: Power Windows
NOTE: For emergency exit with the system engaged, move the lock plunger up (unlocked position), roll down the window, and open the door with the outside door handle. POWER WINDOWS POWER WINDOW SWITCHES The control on the driver’s door has up-down switches that give you fingertip control of all four power win- dows.
Page 38: Auto Window Down - If Equipped
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the win- dows while operating the power window switches. Such entrapment may result in serious injury or death.
Page 39: Auto Window Up - If Equipped
AUTO WINDOW UP — IF EQUIPPED Lift the window switch to the second detent, release, and the window will go up automatically. To cancel the Auto Up movement, operate the switch either in the up or down direction and release the switch. To close the window part way, lift the window switch to the first detent and release it when you want the window to stop.
Page 40: Window Lockout Switch
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOW LOCKOUT SWITCH The window lockout switch on the driver’s door allows you to disable the window control on the other doors. To disable the window controls on the other doors, press the window lock button.
Page 41: Trunk Release
TRUNK RELEASE From inside the car the trunk lid can be released by depressing the Trunk Release Button located on the instrument panel to the left of the steering wheel. The transmis- sion must be in Park before the switch will operate. NOTE: The gear selector lever must be in PARK for this switch to operate.
Page 42: Trunk Internal Emergency Release
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE TRUNK INTERNAL EMERGENCY RELEASE Interior Trunk Emergency Release NOTE: As a security measure, a Trunk Internal Emer- gency Release lever is built into the trunk latching mechanism. In the event of an individual being locked inside the trunk, the trunk can be simply opened by pulling on the glow-in-the-dark handle attached to the trunk latching mechanism.
Page 43 • Supplemental Side Airbag Inflatable Curtains (SABIC) that span the front and second rows for sedans — if equipped • Supplemental seat side (Thorax) airbags — if equipped • Front seat belt retractors incorporate pretensioners to enhance occupant protection by managing occupant energy during an impact event.
Page 44: Lap/Shoulder Belts
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and cause a collision that includes you. This can happen far away from home or on your own street.
Page 45 WARNING! • Wearing your belt in the wrong place could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of part of the belt. Follow these instructions to wear your seat belt safely and to keep your pas- sengers safe, too.
Page 46 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” WARNING! • A belt that is buckled into the wrong buckle will not protect you properly.
Page 47 WARNING! • A belt that is worn under your arm is very danger- ous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries.
Page 48 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen.
Page 49: Adjustable Upper Shoulder Belt Anchorage
1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate. 3.
Page 50: Rear Seat Belts
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REAR SEAT BELTS Three point belts are nonadjustable for outboard and center rear passengers on sedans. The center belt is mounted to the rear shelf panel and exits through a bezel in the panel. SEAT BELT PRETENSIONERS The seat belts for both front seating positions are equipped with pretensioning devices that are designed to...
Page 51: Beltalert Programming
BeltAlert will be reactivated if the driver’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h). BELTALERT PROGRAMMING BeltAlert can be enabled or disabled by your authorized dealer or by following these steps: NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or START position.
Page 52: Automatic Locking Mode
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE AUTOMATIC LOCKING MODE In this mode, the shoulder belt is automatically pre- locked. However, the belt will still retract to remove any slack in the shoulder belt. The Automatic Locking Mode is available on all passenger-seating positions. Use the Automatic Locking Mode anytime a child safety seat is installed in a passenger seating position.
Page 53: Supplemental Restraint System (Srs) - Airbag
Seat Belt Extender If a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your dealer can provide you with a seat belt extender. This extender should be used only if the existing belt is not long enough.
Page 54: Airbag System Components
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Front Airbag Components NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity and occupant size.
Page 55: Front Seat Airbag Features
• Front Seat— side mounted (Thorax) Airbags — If Equipped • Front Impact Sensors • Side Impact Sensors (If Equipped) • Steering Wheel and Column • Instrument Panel • Seat Belt Reminder Light • Knee Impact Bolster • Front Seat Belt Pretensioners FRONT SEAT AIRBAG FEATURES The front airbag system has dual-stage driver and front passenger airbags.
Page 56 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Front Passenger Airbag Special Features A new active venting front-passenger airbag is designed to reduce the risk of occupants who may be out of position by the use of active vents positioned on each side of the airbag.
Page 57 Supplemental Side Airbag Inflatable Curtain (SABIC) — If Equipped Supplemental Side Airbag Inflatable Curtain (SABIC) Airbags offer side-impact protection to front and rear seat outboard occupants in addition to that provided by the body structure. Each airbag features inflated chambers place adjacent to the head of each outboard occupant that reduce the potential for side-impact head injuries.
Page 58 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the airbag covers or attempt to open them manually. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflat- ing.
Page 59 The seat belts are designed to protect you in many types of collisions. The front airbags deploy in moderate to severe frontal collisions. If your vehicle is equipped, the side airbag on the crash side of the vehicle is triggered in moderate to severe side collisions.
Page 60 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate. 4. If your vehicle has side airbags, do not lean against the door, airbags will inflate forcefully into the space between you and the door.
Page 61: Airbag Deployment Sensors And Controls
AIRBAG DEPLOYMENT SENSORS AND CONTROLS Occupant Restraint Controller (ORC) The Occupant Restraint Controller System (ORC) is part of a Federally regulated safety system required for this vehicle. The ORC determines if a frontal collision is severe enough to require the airbags to inflate. Based on the sensor signals, a central electronic Occupant Restraint Controller (ORC) deploys the front airbags, side inflat- able airbag curtains (if equipped), seat-mounted side...
Page 62 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Ignoring the AIRBAG light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away.
Page 63 (ORC) to properly classify the front passenger and calcu- late the proper airbag deployment. Do not make any modifications to the front passenger seat components, assembly, or to the seat cover. The following requirements must be strictly adhered to: • Do not make any modifications to the front passenger seat components, assembly, or to the seat cover in any way.
Page 64 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Accident Response System In the event of an impact that causes airbag deployment, with the vehicle stopped, and the vehicle communication network intact, and the power intact, the Enhanced Accident Response System performs the following func- tions: •...
Page 65 process that generates the nontoxic gas used for airbag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor.
Page 66 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you.
Page 67: Event Data Recorder (Edr)
Airbag Light You will want to have the airbags ready to inflate for your protection in a collision. While the airbag system is designed to be mainte- nance free, if any of the following occurs, have an authorized dealer service the system immediately. •...
Page 68 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE used by DaimlerChrysler Corporation and others to learn more about the possible causes of crashes and associated injuries in order to assess and improve vehicle perfor- mance. In addition to crash investigations initiated by DaimlerChrysler Corporation, such investigations may be requested by customers, insurance carriers, govern- ment officials, and professional crash researchers, such as...
Page 69: Child Restraint
Data Parameters that May Be Recorded: • Diagnostic trouble code(s) and warning light status for electronically-controlled safety systems, including the airbag system • Airbag disable light status (if equipped) • Time of airbag deployment (in terms of ignition cycles and vehicle mileage) •...
Page 70 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are.
Page 71 • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag. An airbag deployment could cause severe injury or death to infants in this position. Older Children and Child Restraints Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle.
Page 72 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips on getting the most out of your child restraints: • Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seatback, should use the lap/shoulder belt in a rear seat.
Page 73 around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position. • Buckle the child into the seat according to the child restraint manufacturer’s directions. • When your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle.
Page 74 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Rear Seat LATCH Anchors Child restraints systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the top tether anchorage have been available for some time.
Page 75 have tether straps, and you are urged to take advantage of all of the available attachments provided with your child restraint in any vehicle. NOTE: When using the LATCH attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed and out of reach of children.
Page 76 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE window. These tether strap anchorages are under a plastic cover with this symbol on it. Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap.
Page 77 the child restraint belt path and then buckle it. This should stow the seat belt out of the reach of an inquisitive child. Remind all children in the vehicle that the seat belts are not toys and should not be played with, and never leave your child unattended in the vehicle.
Page 78 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE between the two posts. If not possible, lower the head restraint and pass the tether strap around the outboard side of the head restraint. 3. Attach the tether strap hook (A) of the child restraint to the anchor (B) and remove slack in the tether strap according to the child restraint manufacturer’s instruc- tions.
Page 79 In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle-end belt several times to shorten it.
Page 80: Engine Break-In Recommendations
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts. ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine in your vehicle.
Page 81: Safety Checks You Should Make Inside The Vehicle
Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area. If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle.
Page 82: Periodic Safety Checks You Should Make Outside The Vehicle
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. NOTE: If the defrost feature is not functioning, the cause should be located and corrected immediately by an authorized service center.
Page 83 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors .......85 Inside Day/Night Mirror — If Equipped ..85 Automatic Dimming Mirror —...
Page 84 82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Training ......119 Seats ....... . 120 Manual Front Seat Adjustments .
Page 85 Headlights With Wipers Feature (Available With Auto Headlights Only) ..137 Windshield Washers ....138 Adding Washer Fluid ....138 Tilt/Telescoping Steering Column .
Page 86 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electrical Power Outlets ....153 Electrical Outlet Use With Engine Off ..154 Cigar Lighter And Ash Receiver —...
Page 87: Mirrors
MIRRORS INSIDE DAY/NIGHT MIRROR — IF EQUIPPED Adjust the mirror to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical mirror adjustment. Adjusting Rear View Mirror UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle).
Page 88: Automatic Dimming Mirror - If Equipped
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE AUTOMATIC DIMMING MIRROR — IF EQUIPPED This mirror will automatically adjust for annoying head- light glare from vehicles behind you. Push in the button on the face of the mirror to activate the dimming feature. Automatic Dimming Mirror —...
Page 89: Adjusting Side View Mirrors
Power Mirror Adjust Switch After selecting a mirror, move the knob in the same direction you want the mirror to move. When finished, return the knob to the center O (OFF) position to guard against accidentally moving a mirror position. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Mirror Directions ADJUSTING SIDE VIEW MIRRORS...
Page 90: Illuminated Vanity Mirrors - If Equipped
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirror — Passenger’s Side Adjust the convex outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle. WARNING! Vehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are.
Page 91: Hands-Free Communication (Uconnect ) - If Equipped
NOTE: For UConnect customer support, visit the following websites: • www.chrysler.com/uconnect • www.dodge.com/uconnect • www.jeep.com/uconnect • or call 1–877–855–8400 UConnect allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle and enables you to mute the system’s microphone...
Page 92 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE a separate 32-name phonebook accessible only in that language. This system is driven through your Bluetooth “Hands-Free profile” cellular phone. UConnect features Bluetooth technology - the global standard that enables different electronic devices to connect to each other without wires or a docking station, so UConnect works no matter where you stow your cellular phone (be it your purse, pocket, or briefcase), as long as your phone is...
Page 93: Operation
can be adjusted either from the radio volume control knob or from the steering wheel radio control (right switch), if so equipped. The radio display will be used for visual prompts from the UConnect system such as CELL or caller ID on certain radios.
Page 94 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Help Command If you need assistance at any prompt, or if you want to know your options at any prompt, say Help following the beep. The UConnect system will play all the options at any prompt if you ask for help.
Page 95 • For identification purposes, you will be prompted to give the UConnect system a name for your cellular phone. Each cellular phone that is paired should be given a unique phone name. • You will then be asked to give your cellular phone a priority level between 1 and 7, with 1 being the highest priority.
Page 96 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Call by Saying a Name • Press the PHONE button to begin. • After the Ready prompt and the following beep, say “Call. • The system will prompt you to say the name of the person you want to call.
Page 97 After you are finished adding an entry into the phone- book, you will be given the opportunity to add more phone numbers to the current entry or to return to the main menu. The UConnect system will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations.
Page 98 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Edit Entries in the UConnect Phonebook NOTE: Editing names in the phonebook is recom- mended when the vehicle is not in motion. • Press the PHONE button to begin. • After the Ready prompt and the following beep, say Phonebook Edit.
Page 99 from which you choose. To select one of the entries from the list, press the “Voice Recognition” button while the UConnect system is playing the desired entry and say Delete. • After you enter the name, the UConnect system will ask you which designation you wish to delete: home, work, mobile, pager, or all.
Page 100: Phone Call Features
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The UConnect system will then prompt you as to the number designation you wish to call. • The selected number will be dialed. Phone Call Features The following features can be accessed through the UConnect system if the feature(s) are available on your cellular service plan.
Page 101 Call followed by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in progress. To go back to the first call, refer to Toggling Between Calls in this section. To combine two calls, refer to Conference Call in this section.
Page 102: Uconnect System Features
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE hold may not become active automatically. This is cell phone-dependent. To bring the call back from hold, press and hold the PHONE button until you hear a single beep. Redial • Press the PHONE button to begin. •...
Page 103 • After the Ready prompt and the following beep, say the name of the language you wish to switch to English, Espanol, or Francais. • Continue to follow the system prompts to complete language selection. After selecting one of the languages, all prompts and voice commands will be in that language.
Page 104 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Your phone must be turned on and paired to the UConnect system to allow use of this vehicle feature in emergency situations, when the cell phone has network coverage and stays paired to the UConnect system. Towing Assistance If you need towing assistance: •...
Page 105 When calling a number with your UConnect system that normally requires you to enter in a touch-tone sequence on your cellular phone keypad, you can press the “Voice Recognition” button and say the sequence you wish to enter, followed by the word Send. For example, if required to enter your PIN followed with a pound, (3 7 4 6 #), you can press the “Voice Recognition”...
Page 106 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turning Confirmation Prompts On/Off Turning confirmation prompts off will stop the system from confirming your choices (e.g., the UConnect sys- tem will not repeat a phone number before you dial it). • Press the PHONE button to begin. •...
Page 107: Advanced Phone Connectivity
Mute/Un-Mute (Mute Off) When you mute the UConnect system, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the UConnect system: •...
Page 108 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, say List Phones. • The UConnect system will play the phone names of all paired cellular phones in order from the highest to the lowest priority. To “select” or “delete” a paired phone being announced, press the “Voice Recogni- tion”...
Page 109: Things You Should Know About Your Uconnect System
Things You Should Know About Your UConnect System UConnect Tutorial To hear a brief tutorial of the system features, press the PHONE button and say “UConnect Tutorial.” Voice Training For users experiencing difficulty with the system recog- nizing their voice commands or numbers, the UConnect system Voice Training feature may be used.
Page 110 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Speak normally, without pausing, just as you would speak to a person sitting a few feet/meters away from you. • Make sure that no one other than you is speaking during a voice recognition period. •...
Page 111 • In a convertible vehicle, system performance may be compromised with the convertible top down. Far End Audio Performance • Audio quality is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, •...
Page 112 110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 113 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111...
Page 114 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 115 Voice Commands Primary Alternate(s) zero three four five seven eight nine star (*) plus (+) pound (#) add location UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Voice Commands Primary Alternate(s) call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol...
Page 116 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Primary Alternate(s) language list names list phones mobile mute mute off new entry pager pair a phone phone pairing pairing phonebook phone book previous record again redial Voice Commands Primary Alternate(s) return to main menu return or main menu select phone...
Page 117: General Information
General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired op- eration.
Page 118: Commands
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pressing the VR hard-key while the system is speaking is known as “barging in.” The system will be interrupted and you can add or change commands. This will become helpful once you start to learn the options. NOTE: At any time, you can say the words CANCEL, HELP, or MAIN MENU.
Page 119 Main Menu Start a dialogue by pressing the VR hard-key. You may say MAIN MENU to switch to the main menu. In this mode, you can say the following commands: • RADIO (to switch to the radio mode) • DISC (to switch to the disc mode) •...
Page 120 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Satellite Radio To switch to satellite radio mode say SAT or SATELLITE RADIO. In this mode, you may say the following com- mands: • CHANNEL NUMBER (to change the channel by its spoken number) •...
Page 121: Voice Training
− CONTINUE (to continue recording) − DELETE (to delete the recording) • PLAY MEMOS (to play previously recorded memos) — During the playback you may press the VR hard- key to stop playing memos. You continue by saying one of the following commands: −...
Page 122: Seats
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS Manual Front Seat Adjustments Forward/Rearward The adjusting bar is at the front of the seats, near the floor. Pull the bar up to move the seat to the desired position. Manual Seat Adjusting Bar After releasing the adjusting bar, apply forward and rearward body pressure to be sure the seat is latched.
Page 123 Driver Seat Manual Height Adjuster — If Equipped A lever style height adjustment feature enhances comfort for petite as well as tall drivers. A lever with a ratcheting mechanism, located on the outboard side of the seat, raises and lowers it. Total travel is 2.2 in. (56 mm). Manual Seat Height Adjustment Lever UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Reclining Bucket Seats...
Page 124 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked.
Page 125: Power Seats - If Equipped
Power Seats — If Equipped The power seat switches are on the outboard side of the seat near the floor. Use the front switch to move the seat up, down, forward, rearward, or to tilt the seat. The rear switch controls the seatback recliner. Power Seat Switches UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 CAUTION!
Page 126: Fold-Flat Front Passenger Seat
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE This feature heats leather or cloth front driver and passenger seats. The controls for the heated seats are located in the center console below the climate controls. There are indicator lights in the switches, which indicate a low heat setting (one light lit) or high heat setting (two lights lit).
Page 127: Adjustable Head Restraints
The hard seatback features a work surface and a molded rim for retaining items stored on the seat back panel. Fold Flat Front Passenger Seat UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 ADJUSTABLE HEAD RESTRAINTS Head restraints can reduce the risk of whiplash injury in the event of impact from the rear.
Page 128: Folding Rear Seat
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE FOLDING REAR SEAT To provide additional storage area, the rear seatback can be folded forward. Pull on the loops shown in the picture to fold down either or both seatbacks. When returning the rear seat back to the upright position, be sure the seat back is latched.
Page 129: Folding Rear Seat Center Armrest
FOLDING REAR SEAT CENTER ARMREST The rear seat is equipped with a folding armrest with cup holders. Folding Rear Seat Armrest UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located under the left side of the instrument panel.
Page 130 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Then lift the secondary latch located under the front edge of the hood, near the center and raise the hood. Hood Safety Catch Use the hood prop rod to secure the hood in the open position.
Page 131: Lights
WARNING! If the hood is not fully latched it could fly up when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving. LIGHTS MAP/READING/INTERIOR LIGHTS These lights are mounted between the sun visors above the rear view mirror.
Page 132: Multi-Function Control Lever
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE because a door is open. This includes the glove box light, but not the trunk light. To restore interior light operation, either turn the ignition switch ON or cycle the light switch. MULTI-FUNCTION CONTROL LEVER The Multi-Function Control Lever controls the operation of the headlights, parking lights, turn signals, headlight beam selection, instrument panel light dimming, interior...
Page 133: Automatic Headlight System - If Equipped
Dimmer Control AUTOMATIC HEADLIGHT SYSTEM — IF EQUIPPED Turning the end of the multi-function control lever to the third detent, “A” (Auto), will activate the automatic headlight system. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 With the engine running and the multi-function control lever in the “A”...
Page 134: Daytime Running Lights (Drl) - If Equipped
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If the Multi-Function Control Lever is held in the flash to pass position for more than 15 seconds, the high beams will shut off. If this occurs, wait 30 seconds for the next flash to pass operation. DAYTIME RUNNING LIGHTS (DRL) —...
Page 135: Turn Signals
Front Fog Light Control NOTE: The front fog lights will only operate with the headlights on low beam. Selecting high beam headlights will turn off the front fog lights. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 TURN SIGNALS Move the Multi-Function Control Lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights.
Page 136: Highbeam/Lowbeam Select Switch
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the fuse or indicator bulb is defective.
Page 137 Windshield Wiper/Washer Lever Rotate the end of the lever to the first detent past the intermittent settings for Low-speed wiper operation, or to the second detent past the intermittent settings for High-speed wiper operation. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 NOTE: The wipers will automatically return to the PARK position if you turn off the ignition switch while they are operating.
Page 138: Intermittent Wiper System
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE INTERMITTENT WIPER SYSTEM Use the intermittent wiper system when weather condi- tions make a single wiping cycle with a variable pause between cycles desirable. Rotate the end of the Wind- shield Wiper/Washer Control Lever to the first detent, and then turn the end of the lever to select the desired delay interval.
Page 139: Mist Feature
MIST FEATURE Push down on the wiper control lever to activate a single wipe to clear the windshield of road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate. Mist Control UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 HEADLIGHTS WITH WIPERS FEATURE (Available...
Page 140: Windshield Washers
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WASHERS To use the washer, pull the Windshield Wiper/Washer Control lever toward you and hold it for as long as washer spray is desired. If you activate the washer while the wiper control is in the delay range, the wipers will operate in low speed for two wipe cycles after releasing the lever and then resume the intermittent interval previously selected.
Page 141: Tilt/Telescoping Steering Column
TILT/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping control handle is located below the steering wheel at the end of the steering column.
Page 142: Electronic Speed Control - If Equipped
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over the accelerator operation at speeds greater than 25 mph (40 km/h). The Speed Control Lever is located on the right side of the steering wheel.
Page 143: To Set Desired Speed
WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you are not using it. To Set Desired Speed: When the vehicle has reached the desired speed, push down on the lever and release SET DECEL.
Page 144: To Vary Speed Setting
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Vary Speed Setting: When the speed control is ON, speed can be increased by pushing up and holding RESUME ACCEL. Release the lever when the desired speed is reached, and the new speed will be set.
Page 145: Garage Door Opener - If Equipped
On steep hills, a greater speed loss or gain may occur so it may be preferable to drive without speed control. GARAGE DOOR OPENER — IF EQUIPPED HomeLink replaces up to three remote controls (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting, or home security systems.
Page 146: Programming Homelink
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse”...
Page 147 Your vehicle should be parked outside of the garage when programming. Begin Programming 1. Turn the ignition switch to the ON/RUN position. 2. Hold the battery side of the hand-held transmitter away from the HomeLink button you wish to program. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink button you wish to program while keeping the indicator light in view.
Page 148 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the indicator light stays on constantly, programming is complete and the garage door (or device) should activate when the HomeLink button is pressed. If the indicator light blinks rapidly for two seconds, and then turns to a constant light, proceed to Step 5 “Pro- gramming A Rolling Code System.”...
Page 149 NOTE: There are 30 seconds in which to initiate the next step after the “Learn” button has been pressed. 7. Return to the vehicle and press the programmed HomeLink button twice (holding the button for two seconds each time). If the device is plugged in and activates, programming is complete.
Page 150: Gate Operator/Canadian Programming
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE GATE OPERATOR/CANADIAN PROGRAMMING Canadian radio frequency laws require transmitter sig- nals to time-out (or quit) after several seconds of trans- mission – which may not be long enough for HomeLink to pick up the signal during programming. Similar to this Canadian law, some U.S.
Page 151: Troubleshooting Tips
TROUBLESHOOTING TIPS If you are having trouble programming HomeLink , here are some of the most common solutions: • Replace the battery in the original transmitter. • Press the “Learn” button on the Garage Door Opener to complete the training for a Rolling Code. •...
Page 152: Power Sunroof - If Equipped
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED The sunroof controls are mounted between the sun visors in the Dome/Reading Lamp. Power Sunroof Switch 1 - Left Interior Light 3 - ATC Sensor - If Equipped 2 - Power Sunroof Switch 4 - Right Interior Light WARNING!
Page 153: Sunroof Operation
SUNROOF OPERATION Opening Sunroof Manually Press the switch rearward and hold, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. During this opera- tion, any release of the sunroof switch will stop the sunroof.
Page 154: Sunshade Operation
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SUNSHADE OPERATION The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. NOTE: The sunshade cannot be closed if the sunroof is open. WIND BUFFETING Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears.
Page 155: Understanding The Features Of Your Vehicle 153
ELECTRICAL POWER OUTLETS There are two 12-volt electrical outlets on this vehicle. Both of the outlets are protected by a fuse. The instrument panel power outlet, located below the climate control knobs, has power available only when the ignition is on. This outlet will also operate a conventional cigar lighter unit.
Page 156: Electrical Outlet Use With Engine Off
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The center console power outlet is powered directly from the battery (power available at all times). Items plugged into this outlet may discharge the battery and/or prevent engine starting. Console Interior Electrical Outlet Use With Engine Off CAUTION! •...
Page 157: Cigar Lighter And Ash Receiver - If Equipped
CIGAR LIGHTER AND ASH RECEIVER — IF EQUIPPED CUPHOLDER ASH RECEIVER — IF EQUIPPED An optional ash receiver is available from your autho- rized dealer and will fit in the center console front cupholder. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 CAUTION! For vehicles equipped with the heated and cooled cupholder, locate the cup holder ash receiver in the...
Page 158: Console Features
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONSOLE FEATURES The center console armrest slides forward from design position to provide added user comfort. Two cupholders can accommodate large sized fast food beverage contain- ers, and 20 oz (500 ml) bottles. A one-piece cup holder insert for both cavities can easily be removed for clean- ing.
Page 159: Video Console - If Equipped
1. The left latch opens to the top storage area. 2. The lower bin can be accessed directly, without first exposing the upper bin, by operating the right latch with the armrest down. 3. The first storage bin can be used to hold smaller items. 4.
Page 160: Cup Holders
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Audio/Video RCA Jacks Video Console See Section Four, “Video Entertainment System-If Equipped,” of this manual, for further information. CUP HOLDERS Heated or Cooled Cup Holder — If Equipped With this feature the rear cavity of the cup holder can keep cool beverages cool, and hot beverages hot.
Page 161: Rear Bottle Holders
Heated or Cooled Cupholder CAUTION! Make sure the beverage container can withstand the temperatures shown above, when using the Cooled or Heated Cup Holder. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 Rear Bottle Holders There are built-in bottle holders located in both rear door trim panels.
Page 162: Storage
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! If containers of hot liquid are placed in the bottle holder, they can spill when the door is closed, burn- ing the occupants. Be careful when closing the doors to avoid injury. STORAGE CARGO AREA The 60/40 split-folding rear seat provides cargo-carrying...
Page 163: Beverage Cooler Storage Bin - If Equipped
WARNING! • The weight and position of cargo and passengers can change the vehicle center of gravity and ve- hicle handling. To avoid loss of control resulting in personal injury, follow these guidelines for loading your vehicle: • Always place cargo evenly on the cargo floor. Put heavier objects as low and as far forward as possible.
Page 164 162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The cooling bin will hold up to four, standing, 12 ounce, beverage cans. The cooler bin is also equipped with a soft molded liner that is removable for easy cleaning. Inside the bin is a vent which, when opened, allows either air conditioned or fresh air to flow into the storage bin.
Page 165: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....167 Instrument Cluster — Base ....168 Instrument Cluster —...
Page 166 164 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - CD Mode For CD And MP3 Audio Play ..... . 198 Notes On Playing MP3 Files ... . . 200 List Button (CD Mode For MP3 Play) .
Page 167 Universal Consumer Interface (UCI) — If Equipped ......227 Connecting The iPod Device ... . 227 Controlling The iPod Using Radio Buttons .
Page 168 166 UNDERSTANDING YOUR INSTRUMENT PANEL Manual Air Conditioning And Heating System . . 242 Automatic Temperature Control (ATC) — If Equipped ......246 Operating Tips .
Page 169: Instrument Panel Features
UNDERSTANDING YOUR INSTRUMENT PANEL 167 INSTRUMENT PANEL FEATURES Instrument Panel Features...
Page 170: Instrument Cluster - Base
168 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — BASE...
Page 171: Instrument Cluster - Premium
UNDERSTANDING YOUR INSTRUMENT PANEL 169 INSTRUMENT CLUSTER — PREMIUM...
Page 172: Instrument Cluster Descriptions
170 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge When the ignition switch is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 2. Fuel Door Reminder This is a reminder that the Fuel Filler Door is located on the left side of the vehicle.
Page 173 5. Low Fuel Light When the fuel level drops to 2 gallons, the fuel symbol will light and a single chime will sound. 6. Charging System Light This light shows the status of the electrical charg- ing system. The light should come on briefly when the ignition is first turned on and remain on briefly as a bulb check.
Page 174 172 UNDERSTANDING YOUR INSTRUMENT PANEL will turn off after the engine is started. If the bulb does not come on during starting, have the system checked by an authorized dealer. If the light comes on and remains on while driving, stop the vehicle and shut off the engine.
Page 175 The two trip odometers show individual trip mileage. To switch from odometer to trip odometers, press and release the Trip Odometer button. To reset a trip odom- eter, display the desired trip odometer to be reset then push and hold the button until the display resets (ap- proximately 2 seconds).
Page 176 174 UNDERSTANDING YOUR INSTRUMENT PANEL indicator system is duty cycle based, which means the engine oil change interval may fluctuate dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the “ON” position. To turn off the message temporarily, press and release the Trip Odometer button on the instrument cluster.
Page 177 Dual Trip Odometer — If Equipped Press and release this button to change the display from odometer to “Trip A.” Press and release it a second time to change the display to “Trip B.” Press and release it a third time to change the display back to the odometer. To reset the trip odometer, first display the trip mileage that you want to reset, “Trip A”...
Page 178 176 UNDERSTANDING YOUR INSTRUMENT PANEL 20. Turn Signal Indicators The arrows will flash in unison with the exterior turn signal, when using the turn signal lever. 21. Front Fog Light Indicator — If Equipped This light shows when the front fog lights are ON. 22.
Page 179 Accordingly, when the low tire pressure telltale illumi- nates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.
Page 180 178 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, type, and/or style.
Page 181 could lead to immediate loss of power or severe catalytic converter damage. The vehicle should be serviced as soon as possible if this occurs. 26. Anti-Lock Warning Light (ABS) This light monitors the ABS. This light will come on when the ignition key is turned to the ON position and may stay on for as long as four seconds.
Page 182 180 UNDERSTANDING YOUR INSTRUMENT PANEL The dual brake system provides a reserve braking capac- ity in the event of a failure to a portion of the hydraulic system. Failure of either half of the dual brake system is indicated by the Brake Warning Light which will turn on when the brake fluid level in the master cylinder has dropped below a specified level.
Page 183: Electronic Vehicle Information Center (Evic) - If Equipped
the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer. The light also will turn on when the parking brake is applied with the ignition switch in the ON position. NOTE: This light shows only that the parking brake is applied.
Page 184 182 UNDERSTANDING YOUR INSTRUMENT PANEL The Electronic Vehicle Information Center (EVIC) fea- tures a driver-interactive display. It is located in the lower left part of the cluster below the fuel and engine tem- perature gauges. The EVIC consists of the following: •...
Page 185: Evic Displays
Press and release the RESET button to accept a selection. The RESET button also resets various Trip Functions. RESET Button EVIC DISPLAYS When the appropriate conditions exist, the Electronic Vehicle Information Center (EVIC) displays the following messages. • Turn Signal On (with a continuous warning chime) •...
Page 186: Oil Change Required
184 UNDERSTANDING YOUR INSTRUMENT PANEL OIL CHANGE REQUIRED Your vehicle is equipped with an engine oil change indicator system. The Oil Change Required message will flash in the EVIC display for approximately 10 seconds after a single chime has sounded to indicate the next scheduled oil change interval.
Page 187 To Reset The Display Reset will only occur if a resettable function is currently displayed. Press and hold the RESET button once to clear the function currently displayed. To reset all resettable functions, press and release the RESET button a second time within three seconds of resetting the currently displayed function (Reset ALL will display during this three second window).
Page 188: Compass Display
186 UNDERSTANDING YOUR INSTRUMENT PANEL • Elapsed Time Shows the total elapsed time of travel since the last reset. Elapsed time will increment when the ignition switch is in the ON or START position. • Display Units In: To make your selection, press and release the RESET button until U.S.
Page 189 UNDERSTANDING YOUR INSTRUMENT PANEL 187 4. Press and release the RESET button and the “CAL” indicator will quit flashing. 5. Drive the vehicle slowly, completing one or more circles (in an area free from large metal or metallic objects) until the “CAL” indicator turns off. The compass will now function normally.
Page 190: Evic Personal Settings (Customer Programmable Features)
188 UNDERSTANDING YOUR INSTRUMENT PANEL 1. Turn the ignition switch to the ON position. Leave the selector lever in PARK. 2. Press and release the MENU button until “Personal Settings” displays in the EVIC. 3. Press and release the STEP button until “Compass Variance”...
Page 191 Auto Unlock on Exit When ON is selected and the transaxle is in the PARK or NEUTRAL position, all doors will unlock when the driver’s door is opened. To make your selection, press and hold the RESET button until ON or OFF appears. Remote Key Unlock When “Driver Door 1st Press”...
Page 192 190 UNDERSTANDING YOUR INSTRUMENT PANEL when exiting the vehicle. To make your selection, press and hold the RESET button until 0, 30, 60, or 90 seconds appears. Headlights With Wipers (Available with Auto Headlights Only) When ON is selected, and the headlight switch is in the AUTO position, the headlights will turn on approxi- mately 10 seconds after the wipers are turned on.
Page 193: Radio General Information
RADIO GENERAL INFORMATION RADIO BROADCAST SIGNALS The radio will provide excellent reception under most operating conditions. Like any system, however, automo- tive radios have performance limitations, due to mobile operation and natural phenomena, which might lead you to believe your sound system is malfunctioning. To help you understand and save you concern about these “ap- parent”...
Page 194: Sales Code Res - Am/Fm Stereo Radio With Cd Player (Mp3 Aux Jack)
192 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The radio, steering wheel radio controls (if equipped), and six-disc CD/DVD changer (if equipped) will remain active for up to 10 minutes after the ignition switch has been turned OFF. Opening a vehicle front door will cancel this feature.
Page 195 Power Switch/Volume Control (Rotary) Push the On/Volume control knob to turn on the radio. Push the On/Volume control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the On/Volume control knob to the right increases the vol- ume and to the left decreases it.
Page 196 194 UNDERSTANDING YOUR INSTRUMENT PANEL Phone Button (UConnect Hands-Free Phone) — If Equipped Press this button to operate the Hands-Free Phone (UConnect ) feature (if equipped). Refer to “Hands-Free Communication (UConnect )” in Section 3. If your vehicle is not equipped with or this feature is not available on your vehicle, a “Not Equipped With UConnect”...
Page 197 INFO Button Press the INFO button for an RDS station (one with call letters displayed). The radio will return a Radio Text message broadcast from an FM station (FM mode only). RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next frequency in the direction of the arrows.
Page 198 196 UNDERSTANDING YOUR INSTRUMENT PANEL MUSIC TYPE Button Pressing this button once will turn on the Music Type mode for five seconds. Pressing the MUSIC TYPE button or turning the Tune/Scroll control knob within five seconds will allow the program format type to be se- lected.
Page 199 16-Digit Character Program Type Sports Talk Top 40 Weather By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name. The Music Type function only operates when in the FM mode.
Page 200: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
198 UNDERSTANDING YOUR INSTRUMENT PANEL the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stored into pushbutton memory.
Page 201 begin to play when you insert the disc. The display will show the disc number, the track number, and index time in minutes and seconds. Play will begin at the start of track 1. CAUTION! • This CD player will accept 4–3/4 in (12 cm) discs only.
Page 202: Notes On Playing Mp3 Files
200 UNDERSTANDING YOUR INSTRUMENT PANEL the current selection. Pressing and holding the SEEK button will allow faster scrolling through the tracks in CD, MP3 modes. SCAN Button Press the SCAN button to scan through each track on the CD currently playing. TIME Button Press this button to change the display from a large CD playing time display to a small CD playing time display.
Page 203 Supported Media (Disc Types) The MP3 file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3, and CDDA+MP3. Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660 Level 1 and Level 2 and includes the Joliet extension. When reading discs recorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read files properly and may be unable to play the file nor-...
Page 204 202 UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats The radio will recognize only files with the *.MP3 exten- sion as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file.
Page 205: List Button (Cd Mode For Mp3 Play)
Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files. Loading times for playback of MP3 files may be affected by the following: •...
Page 206 204 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the INFO button again for three seconds to return to elapsed time display. Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device such as an MP3 player, or cassette player, and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers.
Page 207: Sales Code Req - Am/Fm Stereo Radio And 6-Disc Cd/Dvd Changer (Mp3/Wma Aux Jack)
SALES CODE REQ — AM/FM STEREO RADIO AND 6–DISC CD/DVD CHANGER (MP3/WMA AUX JACK) NOTE: The radio sales code is located on the lower right side of your radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
Page 208 206 UNDERSTANDING YOUR INSTRUMENT PANEL Voice Recognition Button (UConnect Hands-Free Phone) — If Equipped Press this button to operate the Hands-Free Phone (UConnect ) feature (if equipped). Refer to “Hands-Free Communication (UConnect )” in Section 3. If your vehicle is not equipped with or this feature is not available on your vehicle, a “Not Equipped With UConnect”...
Page 209 The clock can also be set by pressing the SETUP button and selecting the “SET HOME CLOCK” entry. Once in this display follow the above procedure, starting at Step INFO Button Press the INFO button for an RDS station (one with call letters displayed).
Page 210 208 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary Tune/Scroll control knob a fifth time and FADE will display. Turn the Tune/Scroll control knob to the left or right to adjust the sound level between the front and rear speakers. Push the rotary Tune/Scroll control knob again to exit setting tone, balance, and fade.
Page 211 16-Digit Character Program Type Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency UNDERSTANDING YOUR INSTRUMENT PANEL 209 station with the same selected Music Type name.
Page 212 210 UNDERSTANDING YOUR INSTRUMENT PANEL • DISC Play/Pause - You can toggle between playing the DVD and pausing the DVD by pushing the SELECT button (if equipped). • DVD Play Options - Selecting the DVD Play Options will display the following: •...
Page 213 Menu Language — If Equipped Selecting this item will allow the user to choose the default startup DVD menu language (effective only if language supported by disc). If you want to select a language not listed, then scroll down and select other. Enter the four-digit country code using the Tune/Scroll control knob to scroll up and down to select the number and then push to select.
Page 214 212 UNDERSTANDING YOUR INSTRUMENT PANEL Aspect Ratio — If Equipped Selecting this item allows you to choose between wide screen, pan scan, and letter box. AutoPlay — If Equipped When this is set to On and a DVD video is inserted, it will bypass the DVD menu screen and automatically play the movie.
Page 215: Operation Instructions
Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6 These buttons tune the radio to the stations that you commit to pushbutton memory {12 AM, 12 FM, and 12 Satellite (if equipped) stations}. DISC Button Pressing the DISC button will allow you to switch from AM/FM modes to Disc modes.
Page 216 214 UNDERSTANDING YOUR INSTRUMENT PANEL Radio display will show LOADING DISC when the disc is loading and “READING DISC” when the radio is reading the disc. CAUTION! This CD player will accept 4–3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism.
Page 217: Notes On Playing Mp3/Wma Files
RW/FF (CD MODE) Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released, or RW or another CD button is pressed. The RW (Rewind) button works in a similar manner. AM or FM Button (CD MODE) Switches the radio to the Radio mode.
Page 218 216 UNDERSTANDING YOUR INSTRUMENT PANEL Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3/ WMA files). Discs created with an option such as keep disc open after writing are most likely multisession discs.
Page 219 WMA File Format Sampling Fre- Specification quency (kHz) 44.1 and 48 ID3 Tag information for artist, song title, and album title are supported for ID3 version 1 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported.
Page 220: List Button (Disc Mode For Mp3/Wma Play)
218 UNDERSTANDING YOUR INSTRUMENT PANEL LIST Button (DISC Mode for MP3/WMA Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the Tune/Scroll control knob. Selecting a folder by pressing the Tune/Scroll control knob will begin playing the files contained in that folder (or the next folder in sequence if the selection does not contain...
Page 221 SCAN Button (Auxiliary Mode) No function. EJECT Button (Auxiliary Mode) No function. TIME Button (Auxiliary Mode) Press the TIME button to change the display from elapsed playing time to time of day. The time of day will display for five seconds. RW/FF (Auxiliary Mode) No function.
Page 222: Sales Code Ren - Multimedia System - If Equipped
220 UNDERSTANDING YOUR INSTRUMENT PANEL Dolby Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. Macrovision This product incorporates copyright protection technol- ogy that is protected by U.S. patents and other intellec- tual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only, unless otherwise authorized by Macrovision.
Page 223: Operating Instructions - Satellite Radio
through the system’s wireless headphones. This means rear seat passengers can watch a DVD on the optional rear seat entertainment system, while the driver and front-seat passenger listen to the radio. Other special features include direct tune, music type selections, easy store presets, backup camera display for vehicles equipped with a backup camera, and on some models, a dual display screen operation.
Page 224 222 UNDERSTANDING YOUR INSTRUMENT PANEL 3. To move the hour forward, touch the screen where the word “Hour” with the arrow pointing upward is dis- played. To move the hour backward, touch the screen where the word “Hour” with the arrow pointing down- ward is displayed.
Page 225: Sales Code Rer - Multimedia System - If Equipped
Touch the screen where the words “Show Time if Radio is Off” are displayed to change the current setting. Changing the Time Zone 1. Turn on the multimedia system. 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3.
Page 226: Operating Instructions - Satellite Radio
224 UNDERSTANDING YOUR INSTRUMENT PANEL The satellite navigation capability combines a Global- Positioning System (GPS)-based navigation system with an integrated color screen to provide maps, turn identi- fication, selection menus, and instructions for selecting a variety of destinations and routes. A shared HDD for the navigation system, the database, and other radio features allows uploads of music and photos from CDs or through the USB port.
Page 227: Clock Setting Procedure
Clock Setting Procedure The GPS receiver in this system is synchronized to the time data being transmitted by the GPS satellites. The satellites’ clock is Greenwich Mean Time (GMT). This is the worldwide standard for time. This makes the sys- tem’s clock very accurate once the appropriate time zone and daylight savings information is set.
Page 228 226 UNDERSTANDING YOUR INSTRUMENT PANEL 3. When this feature is on, a check mark will appear in the box next to the words “Daylight Savings.” Touch the screen where the words “Daylight Savings” are dis- played to change the current setting. Setting the User Clock If you wish to set the clock to a time different from the system clock, you can manually adjust the time by...
Page 229: Universal Consumer Interface (Uci) - If Equipped
2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. 3. When this feature is on, a check mark will appear in the box next to the words “Show Time if Radio is Off.” Touch the screen where the words “Show Time if Radio is Off”...
Page 230: Controlling The Ipod Using Radio Buttons
228 UNDERSTANDING YOUR INSTRUMENT PANEL Controlling The iPod Using Radio Buttons To get into the UCI (iPod ) mode and access a connected iPod , press the AUX button on the radio faceplate. Once in the UCI (iPod ) mode, the iPod available from iPod ) will start playing over the vehicle audio system.
Page 231 Pressing and releasing the FF button will go forward five seconds of the current track. SEEK Buttons Use the SEEK buttons to move to the previous or the next track. If the left (down) button is pressed during the first two seconds of the current track, it will go back to the previous track in the list;...
Page 232: List Or Browse Mode
230 UNDERSTANDING YOUR INSTRUMENT PANEL List or Browse Mode During Play mode, pressing any of the following buttons will take you to List mode. List mode enables you to scroll through the list of menus and tracks on the iPod device.
Page 233: Satellite Radio - If Equipped (Ren/Req/Rer/Res/Reu Radios Only)
After pressing a preset button, you will see the list you are in on the top line and the first item in that list on the second line. To exit the List mode without selecting a track, press the same preset button again to go back to Play mode. LIST Button Pressing the LIST button will take to the top level menu of the iPod .
Page 234: Electronic Serial Number/Sirius Identification Number (Esn/Sid)
232 UNDERSTANDING YOUR INSTRUMENT PANEL number 888-539-7474, or visit the Sirius web site at www.sirius.com, or at www.siriuscanada.ca for Cana- dian residents. Electronic Serial Number/Sirius Identification Number (ESN/SID) Please have the following information available when calling: 1. The Electronic Serial Number/Sirius Identification Number (ESN/SID).
Page 235: Selecting Satellite Mode
Selecting Satellite Mode Press the SAT button until SAT appears in the display. A CD may remain in the radio while in the Satellite radio mode. Satellite Antenna To ensure optimum reception, do not place items on the roof around the rooftop antenna location or strap items to the trunk lid around the trunk lid antenna (if equipped).
Page 236 234 UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button Pressing the SCAN button causes the tuner to search for the next channel, pausing for eight seconds before con- tinuing to the next. To stop the search, press the SCAN button a second time. INFO Button —...
Page 237 By pressing the SEEK button when the Music Type function is active, the radio will be tuned to the next channel with the same selected Music Type name. If a preset button is activated while in the Music Type (Program Type) mode, the Music Type mode will be exited and the radio will tune to the preset channel.
Page 238: Operating Instructions - Hands-Free Phone
236 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second channel to each pushbutton by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2. This allows a total of 12 Satellite channels to be stored into pushbutton memory.
Page 239: Operation With Res / Req Am/Fm Stereo Radio With Cd Player
Remote Sound Controls Operation with RES / REQ AM/FM Stereo Radio with CD Player Right-Hand Switch Functions • Press the top of the switch to increase the volume. • Press the bottom of the switch to decrease the volume. UNDERSTANDING YOUR INSTRUMENT PANEL 237 •...
Page 240: Operation With Rer Multi-Media System
238 UNDERSTANDING YOUR INSTRUMENT PANEL beginning of the previous track if it is within one second after the current track begins to play. • Press the switch up or down twice to listen to the second track on the CD, three times to listen to the third track, and so forth.
Page 241: Video Entertainment System (Ves) - If Equipped
• Press the switch up or down twice to listen to the second track on the CD, three times to listen to the third track, and so forth. • Press the button located in the center of the control to change CDs on the 6-Disc in-dash CD changer radio.
Page 242 240 UNDERSTANDING YOUR INSTRUMENT PANEL • The LCD screen swings up from the rear of the armrest to allow the rear seat passenger(s) to view the display. VES Video Screen NOTE: Close the armrest after the LCD screen has been raised to its viewing position.
Page 243: Radio Operation And Cellular Phones
• Two wireless infrared headsets allow rear seat passen- gers to listen to the same or individual audio sources. Audio/Video RCA Jacks (AUX Jacks) on the rear of the center console enable the monitor to display video directly from a video camera, connect video games for display on the screen, or play music directly from an MP3 player.
Page 244: Climate Controls
242 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Do not apply paper, paper CD labels, or tape to the disc; avoid scratching a disc. 4. Do not use solvents such as benzine, thinner, cleaners, or antistatic sprays. 5. Store a disc in its case after playing. 6.
Page 245 Blower Control Use this control to regulate the amount of air forced through the ven- tilation system in any mode. The blower speed increases as you move the control to the right from the “O” (Off) position. There are four blower speeds.
Page 246 244 UNDERSTANDING YOUR INSTRUMENT PANEL • Panel Air is directed through the outlets in the instru- ment panel. These outlets can be adjusted to direct airflow. The center instrument panel outlets can be NOTE: aimed so that they are directed toward the rear seat passengers for maximum airflow to the rear.
Page 247 NOTE: The air conditioning compressor operates in Mix and Defrost, or a blend of these modes, even if the Air Conditioning Snowflake button is not pressed. This de- humidifies the air to help dry the windshield. To improve fuel economy, use these modes only when necessary. •...
Page 248: If Equipped
246 UNDERSTANDING YOUR INSTRUMENT PANEL • MAX A/C For maximum cooling use the A/C and recirculation buttons at the same time. • Economy Mode If economy mode is desired, press the A/C button to turn off the indicator light and the A/C compressor. Then, move the temperature control to the desired temperature.
Page 249 cabin infrared sensor mounted between the sun-visors and from various sensors located throughout the vehicle. The controls on the climate control provide the system with operator input. Other sensors take account of ve- hicle speed, A/C pressure, outside temperature, and engine cooling temperature.
Page 250 248 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: • The temperature setting can be adjusted at anytime without affecting automatic operation. • Pressing the Air Conditioning Control button while in AUTO mode will cause the LED in the control button to flash three times and then turn off. This indicates that the system is in AUTO mode and requesting the air conditioning is not necessary.
Page 251 UNDERSTANDING YOUR INSTRUMENT PANEL 249...
Page 252 250 UNDERSTANDING YOUR INSTRUMENT PANEL The operator can override the AUTO mode setting to change airflow distribution by rotating the Mode Control knob (on the right) to one of the following positions. • Panel Air is directed through the outlets in the instru- ment panel.
Page 253 • Defrost Air is directed through the windshield and side window demist outlets. Use this mode with maximum blower and temperature settings for best windshield and side window defrosting. • Air Conditioner Control Press this button to turn on the air conditioning during manual operation only.
Page 254: Operating Tips
252 UNDERSTANDING YOUR INSTRUMENT PANEL • Extended use of recirculation may cause the windows to fog. If the interior of the windows begins to fog, press the RECIRCULATION button to return to out- side air. Some temp/humidity conditions will cause captured interior air to condense on windows and hamper visibility.
Page 255 Winter Operation Use of the air Recirculation mode during winter months is not recommended because it may cause window fogging. Vacation Storage Anytime you store your vehicle, or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the fresh air and high blower settings.
Page 256 254 UNDERSTANDING YOUR INSTRUMENT PANEL Outside Air Intake Make sure the air intake, located directly in front of the windshield, is free of obstructions such as leaves. Leaves collected in the air intake may reduce airflow, and if they enter the plenum, they could plug the water drains. In winter months, make sure the air intake is clear of ice, slush, and snow.
Page 257 UNDERSTANDING YOUR INSTRUMENT PANEL 255 Control Setting Suggestions for Various Weather Conditions...
Page 258: Rear Window Features
256 UNDERSTANDING YOUR INSTRUMENT PANEL REAR WINDOW FEATURES Electric Rear Window Defroster — If Equipped The electric Rear Window Defroster Control is located on the climate control. Press this button to turn on the rear window defroster and the heated side mirrors (if equipped).
Page 259: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ..... 261 Automatic Transaxle ....261 Normal Starting .
Page 260 258 STARTING AND OPERATING All Wheel Drive — If Equipped ... . 275 Parking Brake ......276 Brake System .
Page 261 Tread Wear Indicators ....306 Life Of Tire ......306 Replacement Tires .
Page 262 260 STARTING AND OPERATING Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles ..326 Starting ......327 Cruising Range .
Page 263: Starting Procedures
STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belt. Make sure all occupants have securely fastened their seat belts. WARNING! Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons.
Page 264: Normal Starting
262 STARTING AND OPERATING Normal Starting Normal Starting of either a cold or a warm engine does not require pumping or depressing the accelerator pedal. Simply turn the ignition switch to the START position and release when the engine starts. If the engine fails to start within 15 seconds, turn the ignition switch to the LOCK position, wait 10 to 15 seconds, then repeat the normal starting procedure.
Page 265: Extremely Cold Weather (Below 20°F Or 29°C)
Ignition Key Position Extremely Cold Weather (Below To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (avail- able from your authorized dealer) is recommended. If Engine Fails To Start If the engine fails to start after you have followed the NORMAL STARTING procedure, it may be flooded.
Page 266: After Starting
264 STARTING AND OPERATING CAUTION! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to 15 seconds before trying again. After Starting The idle speed will automatically decrease as the engine warms up.
Page 267 Remote Start To exit the Remote Start mode, allow the en- gine to run the cycle or depress the unlock button to disarm the Vehicle Theft Security Alarm and within one minute insert the key STARTING AND OPERATING 265 into the ignition and turn the ignition to the RUN position.
Page 268: Engine Block Heater - If Equipped
266 STARTING AND OPERATING The following conditions must be met before the engine will remote start: • Automatic Transaxle in PARK • All doors are closed • Hood is closed • Hazard Switch is off • Brake Switch is inactive •...
Page 269: Automatic Transaxle
AUTOMATIC TRANSAXLE CAUTION! Damage to the transaxle may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed.
Page 270 268 STARTING AND OPERATING WARNING! It is dangerous to shift the gear selector lever out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse.
Page 271: Brake/Transaxle Interlock System
Brake/Transaxle Interlock System This system prevents you from moving the gear selector lever out of PARK and into any gear unless the brake pedal is pressed. This system is active only while the ignition switch is in the ON position. Always press the brake pedal first, before moving the gear selector out of PARK.
Page 272: Speed / 6 Speed Automatic Transaxle
270 STARTING AND OPERATING feature is inoperable. The engine can be started and stopped, but the key cannot be removed until you obtain service. 4 Speed / 6 Speed Automatic Transaxle / AutoStick — If Equipped The electronically controlled transaxle provides a precise shift schedule.
Page 273 CAUTION! DO NOT race the engine when shifting from PARK or NEUTRAL positions into another gear range as this can damage the drivetrain. REVERSE Use this range for moving the vehicle rearward. Shift into this range only after the vehicle has come to a complete stop.
Page 274 272 STARTING AND OPERATING conditions, using the “5” range will improve perfor- mance and extend transaxle life by reducing excessive shifting and heat build-up. OVERDRIVE— 4 Speed Transaxle This range should be used for most city and highway driving, it provides the smoothest upshifts, downshifts, and best fuel economy.
Page 275 CAUTION! If the transaxle operating temperature exceeds ac- ceptable limits, the vehicle computer will override OVERDRIVE and “3” DRIVE range by changing shift points. This is done to prevent transaxle damage due to overheating. Reset Mode - Electronic Transaxle The transaxle is monitored electronically for abnormal conditions.
Page 276: Autostick - If Equipped
274 STARTING AND OPERATING AUTOSTICK — IF EQUIPPED AutoStick is a driver-interactive transaxle that offers six manual ratio changes to provide you with more control. AutoStick allows you to maximize engine braking, eliminate undesirable upshifts and downshifts, and im- prove overall vehicle performance. This system can also provide you with more control during passing, city driving, cold slippery conditions, mountain driving, trailer towing, and many other situations.
Page 277: All Wheel Drive - If Equipped
• The transaxle will automatically shift up when maxi- mum engine speed is reached while Autostick engaged. • Transaxle shifting will be more noticeable when Autostick is engaged. • If a downshift would cause the engine to over-speed, that shift will not occur until it is safe for the engine. The transaxle will stay in the manually selected gear.
Page 278: Parking Brake
276 STARTING AND OPERATING CAUTION! All wheels must have the same size and type tires. Unequal tire sizes must not be used. Unequal tire size may cause failure of the power transfer unit. PARKING BRAKE When the parking brake is applied with the ignition on, the Brake Light in the instrument cluster will come on.
Page 279 Parking Brake Lever NOTE: • When parking on a hill, it is important to set the parking brake before placing the gear selector in park, otherwise the load on the automatic transaxle locking mechanism may make it difficult to move the selector STARTING AND OPERATING 277 out of park.
Page 280: Brake System
278 STARTING AND OPERATING BRAKE SYSTEM Your vehicle is equipped with power assisted brakes as standard equipment. In the event power assist is lost for any reason (i.e., repeated brake applications with the engine off) the brakes will still function. However, the effort required to brake the vehicle will be much greater than that required with the power system operating.
Page 281: Anit-Lock Brake System (Abs)
Anit-Lock Brake System (ABS) The Anti-Lock Brake System provides increased vehicle stability and brake performance under most braking conditions. The system automatically “pumps” the brakes during severe braking conditions to prevent wheel lock-up. WARNING! Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident.
Page 282 280 STARTING AND OPERATING The ABS light monitors the Anti-Lock Brake System. The light will come on when the ignition switch is turned to the ON position and may stay on for as long as four seconds. If the ABS light remains on or comes on while driving, it indicates that the Anti-Lock portion of the brake system is not functioning and that service is required.
Page 283: Electronic Brake Control Systems - Abs/Tcs/Bas/Esp
• the clicking sound of solenoid valves, • brake pedal pulsations, • and a slight drop or fall away of the brake pedal at the end of the stop. These are all normal characteristics of ABS. WARNING! The Anti-Lock Brake System contains sophisticated electronic equipment that may be susceptible to interference caused by improperly installed or high output radio transmitting equipment.
Page 284: Traction Control System (Tcs)
282 STARTING AND OPERATING help avoid skidding on slippery surfaces during braking. Refer to “Anti-Lock Brake System” in this Section of the manual for more information about ABS. TRACTION CONTROL SYSTEM (TCS) This system monitors the amount of wheel spin of each of the driven wheels.
Page 285: Electronic Stability Program (Esp)
WARNING! • BAS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The BAS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydro- planing.
Page 286 284 STARTING AND OPERATING ESP/TCS Indicator Light The “ESP/TCS Indicator Light, located in the instrument cluster, starts to flash as soon as the tires lose traction and the ESP system becomes active. The ESP/TCS Indicator Light also flashes when TCS is active. If the ESP/TCS Indicator Light begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible.
Page 287 ESP Operating Modes All ESP equipped vehicles can choose the following ESP operating modes: ESP ON This is the normal operating mode for ESP. Whenever the vehicle is started the ESP system will be in this mode. This mode should be used for almost all driving situa- tions.
Page 288 286 STARTING AND OPERATING overcome, turn ESP on again by momentarily depressing the “ESP Control Switch.” This may be done while the vehicle is in motion. ESP/BAS Warning Light and ESP/TCS Indicator Light The malfunction indicator for the ESP is com- bined with the BAS indicator.
Page 289: Power Steering
POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible to steer your vehicle.
Page 290: Driving On Slippery Surfaces
288 STARTING AND OPERATING DRIVING ON SLIPPERY SURFACES ACCELERATION Rapid acceleration on snow covered, wet, or other slip- pery surfaces may cause the front wheels to pull errati- cally to the right or left. This phenomenon occurs when there is a difference in the surface traction under the front (driving) wheels.
Page 291: Driving Through Water
DRIVING THROUGH WATER Driving through water more than a few inches/ centimeters deep will require extra caution to ensure safety and prevent damage to your vehicle. Flowing/Rising Water WARNING! Do not drive on, or cross, a road or a path where water is flowing and/or rising (as in storm run-off).
Page 292 290 STARTING AND OPERATING CAUTION! • Driving through standing water may cause dam- age to your vehicle’s drivetrain components. Al- ways inspect your vehicle’s fluids (i.e., engine oil, transmission, axle, etc.) for signs of contamination (i.e., fluid that is milky or foamy in appearance) after driving through standing water.
Page 293: Tire Safety Information
TIRE SAFETY INFORMATION Tire Markings NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. STARTING AND OPERATING 291 •...
Page 294 292 STARTING AND OPERATING Tire Sizing Chart Passenger Car tire size based on U.S. design standards ...blank... Passenger Car tire based on European design standards Light Truck tire based on U.S. design standards Temporary spare tire Overall diameter in inches (in) Section width in millimeters (mm) Aspect Ratio of section height to section width of tire, written in percent (%) 10.5...
Page 295 Load Index (a numerical code associated with the maximum load a tire can carry) A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e., tire pressure, vehicle loading, road conditions, and posted speed limits) ...blank...
Page 296 294 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, EXAMPLE: DOT MA L9 ABCD 0301 ABCD Prior to July 2000, tire manufacturers were only required to have one number to represent the year in which the tire...
Page 297: Tire Loading And Tire Pressure
Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side B-Pillar. Tire Placard Location STARTING AND OPERATING 295 Tire and Loading Information Placard Tire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle...
Page 298 296 STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading Information placard and in the “Vehicle Loading”...
Page 299 amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 = 750, and 1400 – 750 = 650 lbs [295 kg]). 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.
Page 300 298 STARTING AND OPERATING...
Page 301: Tires - General Information
WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 302: Tire Inflation Pressures
300 STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation, also increases tire rolling resistance and results in higher fuel consump- tion.
Page 303 check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under inflated. CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem.
Page 304: Radial-Ply Tires
302 STARTING AND OPERATING Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important.
Page 305: Compact Spare Tire - If Equipped
Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and rein- stalled at the first opportunity.
Page 306: Limited Use Spare - If Equipped
304 STARTING AND OPERATING CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the compact spare installed. Damage to the vehicle may result. Limited Use Spare — If Equipped The limited use spare tire is for temporary emergency use on your vehicle.
Page 307: Tire Spinning
WARNING! Prolonged use of limited use spare, or incorrect tire size of front wheel, may damage the transaxle differ- ential and result in loss of vehicle mobility and could result in loss of vehicle control. Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck.
Page 308: Tread Wear Indicators
306 STARTING AND OPERATING Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes approximately 1/16 in (2 mm).
Page 309: Replacement Tires
Keep dismounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with oil, grease, and gasoline. Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure.
Page 310: Alignment And Balance
308 STARTING AND OPERATING WARNING! • Never use a tire with a smaller load index or capacity, other than what was originally equipped on your vehicle. Using a tire with a smaller load index could result in tire overloading and failure. You could lose control and have an accident.
Page 311: Tire Chains
TIRE CHAINS Due to limited clearance, tire chains are not recom- mended. CAUTION! Damage to the vehicle may result if tire chains are used. SNOW TIRES Some areas of the country require the use of snow tires during Winter. Standard tires are of the all-season type and satisfy this requirement as indicated by the M+S designation on the tire sidewall.
Page 312: Tire Pressure Monitor System (Tpms) - If Equipped
310 STARTING AND OPERATING Follow the Maintenance Schedule in Section 8 for the recommended tire rotation frequency. Remember, more frequent rotation is permissible if desired. Also, correct for anything causing rapid or unusual wear prior to performing the tire rotation. The suggested rotation method is the “forward-cross”...
Page 313 pressure will also increase as the vehicle is driven - this is normal and there should be no adjustment for this increased pressure. • The TPM System will warn the driver of a low tire pressure if the tire pressure falls below the low- pressure warning limit for any reason, including low temperature effects and natural pressure loss through the tire.
Page 314 312 STARTING AND OPERATING CAUTION! • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when us- ing replacement equipment that is not of the same size, type, and/or style.
Page 315: Base System - If Equipped
• Seasonal temperature changes will affect tire pressure, and the TPMS will monitor the actual tire pressure in the tire. BASE SYSTEM — IF EQUIPPED The Tire Pressure Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels.
Page 316 314 STARTING AND OPERATING repeat, providing the system fault still exists. The Tire Pressure Monitoring Telltale Light will turn off when the fault condition no longer exists. A system fault can occur due to any of the following: 1. Jamming due to electronic devices or driving next to facilities emitting the same Radio Frequencies as the TPM sensors.
Page 317: Premium System - If Equipped
PREMIUM SYSTEM — IF EQUIPPED The Tire Pressure Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure readings to the Receiver Module. NOTE: It is particularly important for you to check the tire pressure in all of the tires on your vehicle monthly and to maintain the proper pressure.
Page 318 316 STARTING AND OPERATING Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Light will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires. In addition, the Electronic Vehicle Information Center (EVIC) will display a graphic showing the pressure values of each tire with the low tire pressure values flashing.
Page 319 turn off. The vehicle may need to be driven for up to 10 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information. Check TPMS Warning When a system fault is detected, a chime will sound and the Tire Pressure Monitoring Telltale Light will flash on and off for 75 seconds and then remain on solid.
Page 320 318 STARTING AND OPERATING 1. Jamming due to electronic devices or driving next to facilities emitting the same Radio Frequencies as the TPM sensors. 2. Installing some form of aftermarket window tinting that affects radio wave signals. 3. Lots of snow or ice around the wheels or wheel housings.
Page 321: General Information
5. Once you repair or replace the original road tire, and reinstall it on the vehicle in place of the compact spare, the TPMS will update automatically. In addition, the TPM Telltale Light will turn OFF and the graphic in the EVIC will display a new pressure value instead of dashes (- -), as long no tire pressure is below the low-pressure warning limit in any of the four active road tires.
Page 322: 3.5L Engine
(with the ap- propriate octane rating for your engine) before consider- ing service for the vehicle. Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifica- tions (the World Wide Fuel Charter, WWFC) which...
Page 323: Gasoline/Oxygenate Blends
Reformulated gasolines contain oxygenates, and are spe- cifically blended to reduce vehicle emissions and im- prove air quality. The manufacturer supports the use of reformulated gaso- lines. Properly blended reformulated gasolines will pro- vide excellent performance and durability of engine and fuel system components.
Page 324: Mmt In Gasoline
322 STARTING AND OPERATING MMT IN GASOLINE MMT is a manganese containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with MMT provides no performance advantage beyond gasoline of the same octane number without MMT. Gasoline blended with MMT reduces spark plug life and reduces emission system performance in some vehicles.
Page 325: Carbon Monoxide Warnings
• An out-of-tune engine, or certain fuel or ignition malfunctions, can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate service. Contact your authorized dealer for service assistance.
Page 326: Flexible Fuel- 2.7L Engines Only (Except California Emission States)
324 STARTING AND OPERATING • Guard against carbon monoxide with proper mainte- nance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the trunk closed when driving your vehicle to prevent carbon monoxide and other poisonous ex- haust gases from entering the vehicle.
Page 327: Ethanol Fuel (E-85)
Along with the special E-85 fuel filler cap, your vehicle may display a badge, which also indicates it can operate on E-85. E-85 Badge STARTING AND OPERATING 325 ETHANOL FUEL (E-85) E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline.
Page 328: Fuel Requirements
326 STARTING AND OPERATING FUEL REQUIREMENTS Your vehicle will operate on both unleaded gasoline with an octane rating of 87, or E-85 fuel, or any mixture of these two. For best results, a refueling pattern that alternates be- tween E-85 and unleaded gasoline should be avoided. When you do switch fuels, it is recommended that: •...
Page 329: Starting
STARTING The characteristics of E-85 fuel make it unsuitable for use when ambient temperatures fall below 0°F (-18°C). In the range of 0°F (-18°C) to 32°F (0°C), you may experience an increase in the time it takes for your engine to start, and a deterioration in driveability (sags and/or hesitations) until the engine is fully warmed up.
Page 330: Adding Fuel
328 STARTING AND OPERATING ADDING FUEL FUEL FILLER CAP (GAS CAP) As a reminder, a fuel icon with an arrow indicating which side of the vehicle the fuel filler door is located on, is located in the instrument cluster. The gas cap is behind the fuel filler door, on the left rear quarter panel of the vehicle.
Page 331 Fuel Filler Door Features NOTE: If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle. STARTING AND OPERATING 329 CAUTION! • Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap).
Page 332: Loose Filler Cap Message
330 STARTING AND OPERATING WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • Never add fuel when the engine is running. This is in violation of most state and federal fire regula- tions and doing so will cause the malfunction indicator light to turn on.
Page 333: Vehicle Loading
VEHICLE LOADING Vehicle Loading Capacities Front Seat Occupants ..... . . 2 Rear Seat Occupants ..... . . 3 Luggage.
Page 334: Gross Vehicle Weight Rating (Gvwr)
332 STARTING AND OPERATING The bar code allows a computer scanner to read the Vehicle Identification Number (VIN). Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, and cargo. The total load must be limited so that you do not exceed the GVWR.
Page 335: Loading
Figure out the weight on the front and rear of the vehicle separately. It is important that you distribute the load evenly over the front and rear axles. Overloading can cause potential safety hazards and shorten useful service life. Heavier axles or suspension components do not necessarily increase the vehicle’s GVWR.
Page 336: Trailer Towing
334 STARTING AND OPERATING TRAILER TOWING In this section, you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer, carefully review this information to tow your load as efficiently and safely as possible.
Page 337 Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR. WARNING! It is important that you do not exceed the maximum front or rear GAWR.
Page 338: Trailer Hitch Classifications
336 STARTING AND OPERATING Trailer Hitch Classifications The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Trailer Hitch Classification Definitions Class Max.
Page 339: Trailer Towing Weights (Maximum Trailer Weight Ratings)
Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Transaxle Max. Frontal Area 2.4L/Auto See Note 2.7L/Auto See Note 3.5L/Auto 22 Sq., Ft. (2.0 Sq. M) Refer to local laws for maximum trailer towing speeds. The trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and it should never exceed the weight referenced on the Tire...
Page 340: Trailer And Trailer Tongue Weight
338 STARTING AND OPERATING Trailer and Trailer Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of vehicle and trailer.
Page 341: Towing Requirements
NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the Tire and Loading Information placard in the Tire Safety Information Section of this manual for the maximum combined weight of occupants and cargo for your vehicle.
Page 342 340 STARTING AND OPERATING WARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and that it will not shift during travel. When traile- ring cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.
Page 343 4. Trailer tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always achieve 10% of trailer tongue weight as a percentage of total trailer weight). Towing Requirements — Tires • Do not attempt to tow a trailer while using a compact spare tire.
Page 344 342 STARTING AND OPERATING • Trailer brakes are recommended for trailers over 1,000 lbs (450 kg) and required for trailers in excess of 2,000 lbs (907 kg). CAUTION! If the trailer weighs more than 1,000 lbs (450 kg) loaded, it should have its own brakes with adequate braking capacity.
Page 345: Towing Tips
NOTE: Do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle, but you must mate the harness to a trailer connector. 4-Pin Connector STARTING AND OPERATING 343 7-Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping, and backing the trailer in an area located away from heavy traffic.
Page 346 344 STARTING AND OPERATING Automatic Transaxle The DRIVE range can be selected when towing. How- ever, if frequent shifting occurs while in this range, third gear for a four-speed automatic and the fifth gear for a six-speed AutoStick should be selected. NOTE: Using third or fifth instead of DRIVE while operating the vehicle under heavy operating conditions, will improve performance and extend transaxle life by...
Page 347: Recreational Towing (Behind Motorhome, Etc.)
• Highway Driving Reduce speed. • Air Conditioning Turn off temporarily. • Refer to Cooling System Operating information in the Maintenance section of this manual for more informa- tion. If you have any questions or concerns after reviewing this section, please consult your authorized dealer to for full details on the towing capabilities of the vehicle.
Page 349: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....348 If Your Engine Overheats ....348 Engine Oil Overheating (2.4L Engine Only) —...
Page 350: Hazard Warning Flasher
348 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The flasher switch is located on the instrument panel, below the radio. Depress the switch and both cluster indicators and all front and rear direc- tional signals will flash. Depress the switch again to turn Hazard Warning Flashers off.
Page 351 NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off. The air conditioning system adds heat to the engine cooling system and turning off the A/C removes this heat.
Page 352: Engine Oil Overheating (2.4L Engine Only) - If Equipped
350 WHAT TO DO IN EMERGENCIES WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call a service center if your vehicle overheats. If you decide to look under the hood yourself, refer to Section 7, Maintenance, of this manual.
Page 353: Jack Location
WHAT TO DO IN EMERGENCIES 351 Jack Location The jack and jack-handle are stowed under the load floor in the trunk. Spare Tire Stowage The compact spare tire is stowed under the load floor in the trunk. Spare Tire Removal Lift up the load floor cover and remove the hold down.
Page 354: Preparations For Jacking
352 WHAT TO DO IN EMERGENCIES Preparations For Jacking Park the vehicle on a firm level surface, avoid ice or slippery areas, set the parking brake and place the gear selector in PARK (automatic transaxle) or REVERSE (manual transaxle). Turn OFF the ignition. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic.
Page 355 WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • Block the wheel diagonally opposite the wheel to be raised.
Page 356 354 WHAT TO DO IN EMERGENCIES NOTE: The Jack Handle attaches to the side of the jack with two attachment points. When the jack is partially expanded, the tension between the two attachment points holds the jack handle in place. Removing Jack Handle From Jack 2.
Page 357 WHAT TO DO IN EMERGENCIES 355 Jacking Locations...
Page 358 356 WHAT TO DO IN EMERGENCIES 3. There are two front jacking locations and two rear jacking locations on each side of the body as shown. CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in step 3. 4.
Page 359 WARNING! To avoid possible personal injury, handle the wheel covers with care to avoid contact with any sharp edges. 7. Lower the vehicle by turning the jack screw to the left. 8. Finish tightening the nuts. Push down on the wrench while tightening the wheel nuts.
Page 360: Jump-Starting Procedures Due To A Low Battery
358 WHAT TO DO IN EMERGENCIES 11. Check the tire pressure as soon as possible. Correct pressure as required. JUMP-STARTING PROCEDURES DUE TO A LOW BATTERY Jump-starting remote battery terminals are located under the hood. The battery is stored between the left front headlight assembly and the left front wheel splash shield.
Page 361 1. Wear eye protection and remove any metal jewelry such as watchbands or bracelets that might make an inadvertent electrical contact. 2. When boosting from a battery in another vehicle, park that vehicle within booster cable reach, but without allowing the vehicles to touch. Set parking brake, place automatic transaxle in PARK and turn ignition to LOCK for both vehicles.
Page 362 360 WHAT TO DO IN EMERGENCIES 5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine ground (-) of the vehicle with the discharged battery. Make sure you have a good contact on the engine ground. Refer to the following illustration for jump-starting connections.
Page 363: Freeing A Stuck Vehicle
FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand, or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels. Then shift back and forth between Reverse and First gear.
Page 364: Towing A Disabled Vehicle
362 WHAT TO DO IN EMERGENCIES CAUTION! Racing the engine or spinning the wheels too fast may lead to transaxle overheating and failure. It can also damage the tires. Do not spin the wheels above 30 mph (48 km/h). Do not spin the wheels continu- ously for more than 30 seconds.
Page 365: Towing Without The Ignition Key
If you must use the accessories (wipers, defrosters, etc.) while being towed, the key must be in the ON position, not the ACC position. Make certain the transaxle remains in NEUTRAL. TOWING WITHOUT THE IGNITION KEY Special care must be taken when the vehicle is towed with the ignition in the LOCK position.
Page 366: Towing Without Power - Override Transaxle Interlock System
364 WHAT TO DO IN EMERGENCIES TOWING WITHOUT POWER — OVERRIDE TRANSAXLE INTERLOCK SYSTEM Special care must be taken when the vehicle is towed with the ignition in the LOCK position. A dolly should be used under the front wheels if the rear wheels are raised. Proper towing equipment is necessary to prevent dam- age to the vehicle.
Page 367: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS 2.4L Engine Compartment ....368 2.7L Engine Compartment ....369 3.5L Engine Compartment .
Page 368 366 MAINTAINING YOUR VEHICLE A/C Air Filter — If Equipped ... . 383 Power Steering ..... . . 385 Front Suspension .
Page 369 MAINTAINING YOUR VEHICLE 367 Center High-Mounted Stop Light ..418 Fluids, Lubricants, And Genuine Parts ..422 Fluids And Capacities ....420 Engine .
Page 370: 2.4L Engine Compartment
368 MAINTAINING YOUR VEHICLE 2.4L ENGINE COMPARTMENT...
Page 371: L Engine Compartment
MAINTAINING YOUR VEHICLE 369 2.7L ENGINE COMPARTMENT...
Page 372: 3.5L Engine Compartment
370 MAINTAINING YOUR VEHICLE 3.5L ENGINE COMPARTMENT 3.5L Engine...
Page 373: Onboard Diagnostic System - Obd Ii
ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transaxle control systems. When these systems are oper- ating properly, your vehicle will provide excellent per- formance and fuel economy, as well as maintaining engine emissions well within current government regu- lations.
Page 374: Emissions Inspection And Maintenance
372 MAINTAINING YOUR VEHICLE RESET button to turn off the message. If the problem persists, the message will appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the MIL.
Page 375: Replacement Parts
5. Approximately 15 seconds later, one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition key or start the engine. This means that the vehicle’s OBD II system is not ready and you should not proceed to the I/M station.
Page 376: Authorized Dealer Service
374 MAINTAINING YOUR VEHICLE AUTHORIZED DEALER SERVICE Your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting any procedure yourself.
Page 377 MAINTAINING YOUR VEHICLE 375 The best time to check the engine oil level is about 5 minutes after a fully warmed engine is shut off. Do not check oil level before starting the engine after it has sat overnight. Checking engine oil level when the engine is cold will give you an incorrect reading.
Page 378 376 MAINTAINING YOUR VEHICLE CAUTION! Do not overfill the engine. Overfilling the engine will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature. This could damage your engine. Change Engine Oil The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.
Page 379 Engine Oil Viscosity (SAE Grade) — 2.4L and 2.7L Engines SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. Your engine oil filler cap also shows the recommended engine oil viscosity for your vehicle.
Page 380: Engine Oil Filter
378 MAINTAINING YOUR VEHICLE Materials Added to Engine Oils The manufacture strongly recommends against the addi- tion of any additives (other than leak detection dyes) to the engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental ad- ditives.
Page 381: Spark Plugs
SPARK PLUGS Spark plugs must fire properly to assure engine perfor- mance and emission control. New plugs should be in- stalled at the specified mileage. The entire set should be replaced if there is any malfunction due to a faulty spark plug.
Page 382 380 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition.
Page 383: Maintenance-Free Battery
To minimize the possibility of catalyst damage: • Do not shut off the engine or interrupt the ignition when the transaxle is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle.
Page 384: Air Conditioner Maintenance
382 MAINTAINING YOUR VEHICLE CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked posi- tive (+) and negative (-) and identified on the battery case.
Page 385: A/C Air Filter - If Equipped
WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Section 3 of the Warranty Information book for further warranty information.
Page 386 384 MAINTAINING YOUR VEHICLE The A/C Air Filter is located in the fresh air inlet behind the glove box. Perform the following procedure to re- place the filter: 1. Open the glove box and remove all contents. 2. Push in on the sides of the glove box and pivot the glove box downward.
Page 387: Power Steering
CAUTION! The A/C Air Filter is labeled with an arrow to indicate airflow direction through the filter. Failure to install the filter properly will result in the need to replace it more often. 7. Reinstall the glove box door dampener and glove box. POWER STEERING Checking the power steering fluid level at a defined service interval is not required.
Page 388: Steering Linkage
386 MAINTAINING YOUR VEHICLE STEERING LINKAGE The tie rod end ball joints should be inspected for external leakage and damage when other maintenance is performed. BODY LUBRICATION Locks and all body pivot points, including seat tracks, door hinges, trunk hinges, and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear.
Page 389: Windshield Washers
Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. NOTE: Always refer to the wiper blade packaging for specific installation instructions. Many wiper blade re- placements fit multiple vehicles. WINDSHIELD WASHERS NOTE: Refer to the appropriate “Engine Compartment” diagram in Section 7 for the location of the windshield washer fluid reservoir.
Page 390: Cooling System
388 MAINTAINING YOUR VEHICLE into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for an oil change or lubrication. Replace as required. WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you.
Page 391 Coolant Checks Check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If coolant is dirty or rusty in appearance, the system should be drained, flushed, and refilled with fresh coolant. Check the front of the A/C condenser for any accumulation of bugs, leaves, etc.
Page 392 390 MAINTAINING YOUR VEHICLE CAUTION! • Mixing of coolants other than specified HOAT engine coolants, may result in engine damage and may decrease corrosion protection. If a non-HOAT coolant is introduced into the cooling system in an emergency, it should be replaced with the speci- fied coolant as soon as possible.
Page 393 • Use only high purity water such as distilled or deion- ized water when mixing the water/engine coolant solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where the vehicle is operated.
Page 394 392 MAINTAINING YOUR VEHICLE Disposal of Used Engine Coolant Used ethylene glycol based engine coolant is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by animals or children, do not store ethylene glycol based engine coolant in open containers or allow it to remain in puddles on the ground.
Page 395 humidity accumulating on the radiator and being vapor- ized when the thermostat opens, allowing hot coolant to enter the radiator. If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. •...
Page 396: Hoses And Vacuum/Vapor Harnesses
394 MAINTAINING YOUR VEHICLE HOSES AND VACUUM/VAPOR HARNESSES Inspect surfaces of hoses and nylon tubing for evidence of heat and mechanical damage. Hard or soft spots, brittle rubber, cracking, tears, cuts, abrasions, and exces- sive swelling indicate deterioration of the rubber Pay particular attention to the hoses nearest to high heat sources such as the exhaust manifold.
Page 397 WARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You wouldn’t have your full braking capacity in an emergency.
Page 398 396 MAINTAINING YOUR VEHICLE immediately! Eventual deterioration of the hose can take place resulting in a possibility of a burst failure. WARNING! Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately.
Page 399: Automatic Transaxle
WARNING! • Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. • Use of a brake fluid that has a lower initial boiling point than the recommended MOPAR product or a brake fluid that is unidentified as to FMVSS specification may result in sudden brake failure during hard prolonged braking.
Page 400 398 MAINTAINING YOUR VEHICLE Fluid Level Check — Vehicles with 2.4L and 2.7L Engines Use the following procedure to check the automatic transaxle fluid level properly: 1. Park the vehicle on level ground. 2. Run the engine at curb idle speed for a minimum of 60 seconds.
Page 401 CAUTION! • Using a transmission fluid other than the manu- facturer’s recommended fluid may cause deterio- ration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than that recommended by the manufacturer will result in more frequent fluid and filter changes.
Page 402: Front And Rear Wheel Bearings
400 MAINTAINING YOUR VEHICLE FRONT AND REAR WHEEL BEARINGS Front and rear wheel bearings are permanently sealed. No regular maintenance is required for these compo- nents. APPEARANCE CARE AND PROTECTION FROM CORROSION Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geo- graphic locations and usage.
Page 403 Washing • Wash your vehicle regularly. Always wash your ve- hicle in the shade using Mopar Car Wash or a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar, or other similar deposits have accumu- lated on your vehicle, use Mopar Super Kleen Bug and Tar Remover to remove.
Page 404 402 MAINTAINING YOUR VEHICLE • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating, have your vehicle repaired as soon as pos- sible. The cost of such repairs is considered the respon- sibility of the owner.
Page 405 Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses. Interior Care Instrument Panel Cover The instrument panel cover has a low glare surface, which minimizes reflections in the windshield. Do not use protectants or other products, which may cause undesirable reflections.
Page 406 404 MAINTAINING YOUR VEHICLE WARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. YES Essentials Fabric Cleaning Procedure – If Equipped YES Essentials seats may be cleaned in the following manner: •...
Page 407: Cleaning Center Console Cupholders
Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet, soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners.
Page 408: Fuses - Totally Integrated Power Module (Tipm)
406 MAINTAINING YOUR VEHICLE FUSES — TOTALLY INTEGRATED POWER MODULE (TIPM) The TIPM is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini fuses. A label that identifies each component may be printed on the inside of the cover. Refer to the following chart for FUSES/TIPM location.
Page 409 Car- Mini Cavity tridge Fuse Fuse 20 Amp — Yellow Battery Feed — Cen- 10 Amp ter High Mounted — Stop Light (CHMSL)/ Brake Switch 10 Amp Battery Feed — Igni- — tion Switch 20 Amp Trailer Tow — If —...
Page 410 408 MAINTAINING YOUR VEHICLE Car- Mini Cavity tridge Fuse Fuse 10 Amp — 40 Amp — Green 15 Amp — Lt. Blue 10 Amp — Description Cavity Ignition Off Draw (IOD) — Cabin Com- partment Node (CCN)/ Interior Lighting Battery Feed — Ra- diator Fan Relay IGN Run/ACC —...
Page 411 Car- Mini Cavity tridge Fuse Fuse 25 Amp Battery Feed — PWR — Clear Sunroof Feed Ignition Run — 10 Amp — Heated Mirrors - If Equipped 15 Amp Auto Shutdown — Lt. Blue (ASD) Relay Feed 2 Ignition Run — Occu- pant Classification 10 Amp —...
Page 412 410 MAINTAINING YOUR VEHICLE Car- Mini Cavity tridge Fuse Fuse 10 Amp — 30 Amp — Pink Description Cavity Battery Feed — Switch Bank/ Diagnostic Link Connector/ Powertrain Control Module (PCM) Battery Feed — Anti- Lock Brakes (ABS) Module - if equipped/Electronic Stability Program (ESP) Module - If...
Page 413: Vehicle Storage
CAUTION! • When installing the Totally Integrated Power Module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the Totally Integrated Power Module, and possibly result in an electrical system failure.
Page 414: Bulb Replacement
412 MAINTAINING YOUR VEHICLE NOTE: For lighted switches, see your authorized dealer for replacement instructions. LIGHTS BULBS — Outside Low Beam Headlight ..... 9006 High Beam Headlight.
Page 415 2. Reach into engine compartment and from behind the lamp assembly and grasp the connector. Headlight Housing - Rear View 3. Rotate bulb and connector ⁄ turn and pull outward from assembly. MAINTAINING YOUR VEHICLE 413 Twisting Bulb From Socket CAUTION! Do not touch the new bulb with your fingers.
Page 416 414 MAINTAINING YOUR VEHICLE 4. Pull the bulb out of the socket and replace the bulb. Removing Halogen Bulb From Assembly 5. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. 6. Reinsert the bulb and socket assembly and rotate clockwise ⁄...
Page 417: Fog Lights
Fog Lights 1. Access to the lights through the lower fascia cutout is limited. 2. We recommend you access the lights by turning the steering wheel to allow access and remove the inner fender shield. Fog Light and Connector MAINTAINING YOUR VEHICLE 415 3.
Page 418: Taillights, Rear Turn Signals And Backup Lights - Replacement
416 MAINTAINING YOUR VEHICLE Taillights, Rear Turn Signals And Backup Lights — Replacement The turn signal, brake and taillights and backup lights are located in the rear corner body panel housing. Rear Tail Light Changing the Rear Corner Taillight Bulbs 1.
Page 419 2. Remove the two plastic wing nuts from the taillight housing. Location Plastic Wing Nuts 3. Grasp the taillight and pull firmly outward pushing gently on the studs from inside to disengage the light housing. MAINTAINING YOUR VEHICLE 417 4. Twist and remove socket from light. 5.
Page 420: License Plate Light - Rear
418 MAINTAINING YOUR VEHICLE License Plate Light — Rear 1. Remove two retaining screws holding the light lens in place. Location and Removal of Rear License Light Assembly 2. Gently pry the light assembly loose. 3. Pull bulb from socket, replace and reattach the light assembly with the two retaining screws.
Page 421 2. Twist and remove socket from the back of the light housing. Changing High Mount Stop Light Bulb MAINTAINING YOUR VEHICLE 419 3. Replace the bulb and reinstall the socket into the housing by locking it in place with a twist.
Page 422 420 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Engine Fuel (approximate) All FWD Engines — (Except 2.4L PZEV) 3.5L Engine with AWD (All Wheel Drive) 2.4L PZEV (Partial Zero Emissions Vehicle) Engine Oil with Filter 2.4 Liter Engine (SAE 5W-20, API Certified) 2.7 Liter Engine (SAE 5W-20, API Certified) 3.5 Liter Engine (SAE 10W-30, API Certified) FLUIDS AND CAPACITIES...
Page 423 Engine Cooling System * 2.4 Liter Engine (Mopar Antifreeze/Coolant 5 Year/ 100,000 Mile Formula) or equivalent. 2.7 Liter Engine (Mopar Antifreeze/Coolant 5 Year/ 100,000 Mile Formula) or equivalent. 3.5 Liter Engine (Mopar Antifreeze/Coolant 5 Year/ 100,000 Mile Formula) or equivalent. * Includes heater and coolant recovery bottle filled to MAX level.
Page 424 422 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Engine Coolant Additive Technology) or equivalent Use API Certified engine oil. SAE 5W-20 is recommended. Refer to the engine oil Engine Oil (2.4L, 2.7L) fill cap for the correct SAE grade meeting DaimlerChrysler Material Standard MS- 6395.
Page 425 Component Spark Plugs (2.7L) RE14PMC5 (Gap.050 in [1.27 mm]) Spark Plugs (3.5L) ZFR5LP-13G (Gap.050 in [1.27 mm]) Fuel Selection (2.4L, 2.7L) 87 Octane Fuel Selection (2.7L - EX- CEPT CALIFORNIA EMIS- E-85 Ethanol SION STATES) Fuel Selection (3.5L) 87 to 89 Octane * PZEV = Partial Zero Emission Vehicle MAINTAINING YOUR VEHICLE 423 Fluids, Lubricants, and Genuine Parts...
Page 426 424 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transaxle Mopar ATF+4 Automatic Transmission Fluid. Mopar DOT 3 and SAE J1703 should be used. If DOT 3 brake fluid is not avail- Brake Master Cylinder able, then DOT 4 is acceptable. Use only recommended brake fluids. Power Steering Reservoir Mopar ATF+4 Automatic Transmission Fluid.
Page 427 MAINTENANCE SCHEDULES CONTENTS Emissions Control System Maintenance ..426 Maintenance Schedule ....426 Required Maintenance Intervals ... 429...
Page 428 426 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type, must be done at the times or mileages specified to ensure the continued proper functioning of the Emissions Con- trol System. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
Page 429 oil if it has been six months since your last oil change even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your vehicle off-road for an extended period of time. •...
Page 430 428 MAINTENANCE SCHEDULES NOTE: Six-speed AutoStick Transaxle, if equipped, is sealed therefore, checking the fluid level can only be done by a certified dealership service center. • Check all lights and other electrical items for correct operation. At Each Oil Change •...
Page 431 Required Maintenance Intervals Maintenance Items Change the engine oil and engine oil filter. Rotate the tires. If using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if nec- essary. Inspect the brake linings, and replace if necessary. Replace the air conditioning filter (if equipped).
Page 432 430 MAINTENANCE SCHEDULES Maintenance Items Replace the spark plugs on 2.4L engines (except PZEV* engine). Inspect and adjust the power steering pump belt ten- sion on 2.4L engines. Inspect the generator belt on 2.4L engines, and replace if necessary. Change the automatic transaxle fluid & filter if using your vehicle for any of the following: police, taxi, fleet, or frequent trailer towing.
Page 433 Maintenance Items Replace the timing belt on 2.4L and 3.5L engines. Change the automatic transaxle fluid & filter. Replace the accessory drive belt on 2.7L engines. *P artial Z ero E missions V ehicle † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty.
Page 435 IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......435 Prepare For The Appointment .
Page 436 434 IF YOU NEED CONSUMER ASSISTANCE Department Of Transportation Uniform Tire Quality Grades ......441 Treadwear ......441 Traction Grades .
Page 437: Suggestions For Obtaining Service For Your Vehicle
SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty.
Page 438: Chrysler Llc Customer Center
436 IF YOU NEED CONSUMER ASSISTANCE high quality service. The manufacturer’s authorized deal- ers have the facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer’s service manager first.
Page 439: In Mexico Contact
In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P. 05109 Mexico, D. F. In Mexico City: 5081-4568 Outside Mexico City: 1-800-505-1300 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommuni- cation Devices for the Deaf) equipment at its Customer Center.
Page 440: Warranty Information (U.s. Vehicles Only)
438 IF YOU NEED CONSUMER ASSISTANCE Contract, and you require service after the manufactur- er’s New Vehicle Limited Warranty expires, please refer to the contract documents, and contact the person listed in those documents. We appreciate that you have made a major investment when you purchased the vehicle.
Page 441: Mopar Parts
MOPAR PARTS Mopar fluids, lubricants, parts, and accessories are available from your authorized dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In The 50 United States And Washington, D.C. If you believe that your vehicle has a defect that could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the...
Page 442: Publication Order Forms
440 IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mas- tercard, American Express, and Discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form.
Page 443: Department Of Transportation Uniform Tire
Call toll free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Visit us on the Worldwide Web at: • www.techauthority.com DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle.
Page 444: Temperature Grades
442 IF YOU NEED CONSUMER ASSISTANCE WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory...
Page 445 INDEX...
Page 446 444 INDEX ABS (Anti-Lock Brake System) ....279 Adding Engine Coolant (Antifreeze) ..390 Adding Fuel ......328 Adding Washer Fluid .
Page 447 Automatic Door Locks ..... 32 Automatic Oil Change Indicator ..173,184,426 Automatic Temperature Control (ATC) ..246 Automatic Transaxle .
Page 448 446 INDEX Bulbs, Light ......411 Calibration, Compass ..... 186 Capacities, Antifreeze (Engine Coolant) .
Page 449 Compact Spare Tire ..... . 303 Compass ......186 Compass Calibration .
Page 450 448 INDEX Digital Video Disc (DVD) Player ..220,223 Dimmer Switch, Headlight ....134 Dipsticks Automatic Transaxle .
Page 451 Cooling ......388 Exhaust Gas Caution ....323 Fuel Requirements .
Page 452 450 INDEX Engine Oil ......326 Fuel Requirements ....324,326 Maintenance .
Page 453 Fuel System Caution ..... 329 Fueling ....... 328 Fuses .
Page 454 452 INDEX Heated Seats ......123 Heater ....... 242 Heater, Engine Block .
Page 455 Keyless Entry System (Sedan) ....21 Keys ....... . . 12 Knee Bolster .
Page 456 454 INDEX Security Alarm (Theft Alarm) ....18 Theft Alarm (Security Alarm) ....171 Tire Pressure Monitoring (TPMS) .
Page 457 MP3 Player ......220,223 MTBE/ETBE ......321 Multi-Function Control Lever .
Page 458 456 INDEX Paint Care ......400 Panic Alarm ......25 Parking Brake .
Page 459 Radio (Sound Systems) ....220,223 Rear Cup Holder ......159 Rear Seat, Folding .
Page 460 458 INDEX Schedule, Maintenance ....426 Seat Belt Maintenance ....405 Seat Belt Reminder .
Page 461 Side Window Demisters (Defrosters) ..253 Signals, Turn ......416 Slippery Surfaces, Driving On .
Page 462 460 INDEX Theft System (Security Alarm) ....18 Tilt Steering Column ..... 139 Time Delay, Headlight .
Page 463 Recreational ..... . . 345,363 Weight ......337 Towing Assistance .
Page 464 462 INDEX Understanding Your Instrument Panel ..167 Uniform Tire Quality Grades ....441 Universal Consumer Interface (UCI) Connector . . . 227 Universal Serial Bus (USB) Port .
Page 465 Window Fogging ......253 Windows ......35 Power .
Page 466 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
Page 467 81-226-0830 Third Edition Printed in U.S.A.

This manual is also suitable for:

2008 js avenger sedan

Dodge 2008 Avenger Owner's Manual

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

Quick Links

Chapters

Related Manuals for Dodge 2008 Avenger

Summary of Contents for Dodge 2008 Avenger