HP SignagePlayer mp8200 Hardware Reference Manual
  1. Manuals
  2. Brands
  3. HP Manuals
  4. Desktop
  5. SignagePlayer mp8200
  6. Hardware reference manual
HP SignagePlayer mp8200 Hardware Reference Manual

HP SignagePlayer mp8200 Hardware Reference Manual

Hardware reference guide - hp signageplayer mp8200 and hp signageplayer mp8200s
Hide thumbs Also See for SignagePlayer mp8200:
Table of Contents

Advertisement

Quick Links

Download this manual
Hardware Reference Guide
HP SignagePlayer mp8200, mp8200s

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SignagePlayer mp8200 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for HP SignagePlayer mp8200

Summary of Contents for HP SignagePlayer mp8200

  • Page 1 Hardware Reference Guide HP SignagePlayer mp8200, mp8200s...
  • Page 2 © Copyright 2010–2011 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. Microsoft, Windows, and Windows Vista are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. The only warranties for HP products and...
  • Page 3 About This Book WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information.
  • Page 4 About This Book...

  • Page 5: Table Of Contents

    Table of contents 1 Product Features ....................... 1 Standard Configuration Features ....................1 Front Panel Components ......................2 Rear Panel Components ......................3 Media Card Reader Components ....................4 Keyboard ..........................5 Using the Windows Logo Key ..................6 Serial Number Location ......................7 2 Hardware Upgrades ......................
  • Page 6 Installing a Security Lock ......................30 HP/Kensington MicroSaver Security Cable Lock ............30 Padlock ........................31 HP Business PC Security Lock ..................31 Front Bezel Security ....................35 Appendix A Battery Replacement ..................37 Appendix B Electrostatic Discharge ..................40 Preventing Electrostatic Damage ....................

  • Page 7: Product Features

    Product Features Standard Configuration Features Features may vary depending on the model. For a complete listing of the hardware and software installed in the computer, run the diagnostic utility (included on some computer models only). Figure 1-1 Configuration Standard Configuration Features...

  • Page 8: Front Panel Components

    Front Panel Components Drive configuration may vary by model. Some models have a bezel blank covering the optical drive bay. Figure 1-2 Front Panel Components Table 1-1 Front Panel Components Optical Drive Microphone/Headphone Connector Power On Light USB (Universal Serial Bus) Ports SD Media Card Reader (optional) Hard Drive Activity Light Headphone Connector...

  • Page 9: Rear Panel Components

    Rear Panel Components Figure 1-3 Rear Panel Components Table 1-2 Rear Panel Components Line-Out Connector for powered audio devices Power Cord Connector (green) PS/2 Keyboard Connector (purple) TV Tuner (optional) Universal Serial Bus (USB) ports Line-In Audio Connector (blue) DisplayPort Monitor Connector PS/2 Mouse Connector (green) VGA Monitor Connector RJ-45 Network Connector...

  • Page 10: Media Card Reader Components

    Media Card Reader Components The media card reader is an optional device available on some models only. Refer to the following illustration and table to identify the media card reader components. Figure 1-4 Media Card Reader Components Table 1-3 Media Card Reader Components Slot Media xD-Picture Card (xD)

  • Page 11: Keyboard

    Keyboard Figure 1-5 Keyboard Components Table 1-4 Keyboard Components Function Keys Perform special functions depending on the software application being used. Editing Keys Includes the following: Insert, Home, Page Up, Delete, End, and Page Down. Status Lights Indicate the status of the computer and keyboard settings (Num Lock, Caps Lock, and Scroll Lock).

  • Page 12: Using The Windows Logo Key

    Using the Windows Logo Key Use the Windows Logo key in combination with other keys to perform certain functions available in the Windows operating system. Refer to Keyboard on page 5 to identify the Windows Logo key. Table 1-5 Windows Logo Key Functions The following Windows Logo Key functions are available in Microsoft Windows XP, Microsoft Windows Vista, and Microsoft Windows 7.

  • Page 13: Serial Number Location

    Table 1-5 Windows Logo Key Functions (continued) Windows Logo Key + up arrow Maximizes the window Windows Logo Key + left arrow Snaps the window to the left side of the screen Windows Logo Key + right arrow Snaps the window to the right side of the screen Windows Logo Key + down arrow Minimizes the window...

  • Page 14: Hardware Upgrades

    Hardware Upgrades Serviceability Features The computer includes features that make it easy to upgrade and service. No tools are needed for most of the installation procedures described in this chapter. Warnings and Cautions Before performing upgrades be sure to carefully read all of the applicable instructions, cautions, and warnings in this guide.

  • Page 15: Connecting The Power Cord

    Connecting the Power Cord When connecting the power supply, it is important to follow the steps below to ensure the power cord does not pull free from the computer. Connect the round end of the power cord to the power supply connector on the rear of the computer (1).

  • Page 16: Removing The Computer Access Panel

    Removing the Computer Access Panel To access internal components, you must remove the access panel: Remove/disengage any security devices that prohibit opening the computer. Remove all removable media, such as compact discs or USB flash drives, from the computer. Turn off the computer properly through the operating system, then turn off any external devices. Disconnect the power cord from the power outlet and disconnect any external devices.

  • Page 17: Replacing The Computer Access Panel

    Replacing the Computer Access Panel Align the tabs on the panel with the slots on the chassis then slide the panel towards the front of the chassis until it stops (1). Tighten the thumbscrew to secure the access panel (2). Figure 2-3 Replacing the Computer Access Panel Replacing the Computer Access Panel...

  • Page 18: Removing The Front Bezel

    Removing the Front Bezel Remove/disengage any security devices that prohibit opening the computer. Remove all removable media, such as compact discs or USB flash drives, from the computer. Turn off the computer properly through the operating system, then turn off any external devices. Disconnect the power cord from the power outlet and disconnect any external devices.

  • Page 19: Removing A Bezel Blank

    Removing a Bezel Blank On some models, there is a bezel blank covering the internal drive bay that needs to be removed before installing a drive. To remove a bezel blank: Remove the access panel and front bezel. To remove the bezel blank, push the two retaining tabs that hold the bezel blank in place towards the outer left edge of the bezel (1) and pull the bezel blank inwards to remove it (2).

  • Page 20: Replacing The Front Bezel

    Replacing the Front Bezel Insert the three hooks on the bottom side of the bezel into the rectangular holes on the chassis (1) then rotate the top side of the bezel onto the chassis (2) and snap it into place. Figure 2-6 Replacing the Front Bezel Chapter 2 Hardware Upgrades...

  • Page 21: Changing From Desktop To Tower Configuration

    Changing from Desktop to Tower Configuration Remove/disengage any security devices that prohibit opening the computer. Remove all removable media, such as compact discs or USB flash drives, from the computer. Turn off the computer properly through the operating system, then turn off any external devices. Disconnect the power cord from the power outlet and disconnect any external devices.

  • Page 22: System Board Connections

    System Board Connections Refer to the following illustration and table to identify the system board connectors. Figure 2-8 System Board Connections System Board Connector System Board Label Color Component SATA 3.0 SATA1 light blue Optical Drive Power SATA PWR1 white Optical Drive Mobile PCI Express Module black...

  • Page 23: Installing Additional Memory

    Installing Additional Memory The computer comes with double data rate 3 synchronous dynamic random access memory (DDR3- SDRAM) small outline dual inline memory modules (SODIMMs). SODIMMs The memory sockets on the system board can be populated with up to two industry-standard SODIMMs.

  • Page 24: Populating Sodimm Sockets

    Populating SODIMM Sockets There are two SODIMM sockets on the system board, with one socket per channel. The sockets are labeled XMM1 and XMM3. The XMM1 socket operates in memory channel A. The XMM3 socket operates in memory channel B. Figure 2-9 SODIMM Socket Locations Table 2-1...

  • Page 25: Installing Sodimms

    Installing SODIMMs CAUTION: You must disconnect the power cord and wait approximately 30 seconds for the power to drain before adding or removing memory modules. Regardless of the power-on state, voltage is always supplied to the memory modules as long as the computer is plugged into an active AC outlet. Adding or removing memory modules while voltage is present may cause irreparable damage to the memory modules or system board.
  • Page 26 To remove a SODIMM, press outward on the two latches on each side of the SODIMM (1) then pull the SODIMM out of the socket (2). Figure 2-10 Removing a SODIMM Slide the new SODIMM into the socket at approximately a 30° angle (1) then press the SODIMM down (2) so that the latches lock it in place.

  • Page 27: Replacing The Optical Drive

    Reconnect the power cord and turn on the computer. Lock any security devices that were disengaged when the computer cover or access panel was removed. The computer automatically recognizes the additional memory when you turn on the computer. Replacing the Optical Drive The computer uses a slimline Serial ATA (SATA) optical drive.
  • Page 28 Disconnect the cables on the rear of the optical drive (1), push the green release latch on the right rear side of the drive toward the center of the drive (2), then slide the drive forward and out of the bay through the front bezel (3).

  • Page 29: Preparing The New Optical Drive

    Preparing the New Optical Drive Before the new optical drive can be used, the release latch must be attached. Peel the backing off the adhesive on the release latch. Without allowing the release latch to touch the optical drive, carefully align the holes on the release latch with the pins on the side of the optical drive.

  • Page 30: Installing The New Optical Drive

    Installing the New Optical Drive NOTE: If you are installing an optical drive in a bay that did not previously have a drive in it, you must remove the access panel and the bezel blank covering the opening of the bay before proceeding. Follow the procedures in Removing the Computer Access Panel on page 10 Removing a Bezel...

  • Page 31: Replacing The Hard Drive

    Replacing the Hard Drive NOTE: The computer supports only 2.5-inch Serial ATA (SATA) internal hard drives. Before you remove the old hard drive, be sure to back up the data from the old hard drive so that you can transfer the data to the new hard drive. The 2.5-inch hard drive is enclosed in a carrier under the optical drive.
  • Page 32 Lift the hard drive carrier straight up and out of the chassis. Figure 2-16 Removing the Hard Drive Carrier Remove the four guide screws from the sides of the hard drive carrier. Figure 2-17 Removing the Guide Screws Lift the hard drive up to the top of the carrier (1) and slide the drive out of the carrier (2). Figure 2-18 Removing the Hard Drive from the Carrier Chapter 2 Hardware Upgrades...
  • Page 33 Position the hard drive so that the top of the hard drive is up against the top of the carrier (1) so that the circuit board on the bottom of the hard drive does not come in contact wit the tabs on the bottom of the carrier, then slide the new hard drive into the carrier (2).
  • Page 34 To place the hard drive carrier back in the chassis, align the guide screws with the slots on the drive bay, drop the carrier straight down into the drive bay (1), and press the handle on the carrier all the way down (2) so that the drive is properly seated and locked in place. Figure 2-21 Installing the Hard Drive Carrier Replace the optical drive and reconnect the cable on the back of the optical drive.

  • Page 35: Installing And Removing A Port Cover

    Installing and Removing a Port Cover An optional rear port cover is available for the computer. To install the port cover: Thread the cables through the bottom hole on the port cover (1) and connect the cables to the rear ports on the computer.

  • Page 36: Installing A Security Lock

    Installing a Security Lock HP/Kensington MicroSaver Security Cable Lock There are two cable lock slots on the rear of the computer. The slot next to the thumbscrew should be used when there is no port cover. The slot on the far right should be used when a port cover is installed. Figure 2-24 Installing a Cable Lock with No Port Cover Figure 2-25...

  • Page 37: Padlock

    Padlock Figure 2-26 Installing a Padlock HP Business PC Security Lock Fasten the security cable by looping it around a stationary object. Figure 2-27 Securing the Cable to a Fixed Object Installing a Security Lock...
  • Page 38 Insert the Kensington lock into the Kensington lock slot on the back of the monitor and secure the lock to the monitor by inserting the key into the key hole on the rear of the lock and rotating the key 90 degrees. Figure 2-28 Installing the Kensington Lock on the Monitor Slide the security cable through the hole in the Kensington lock on the rear of the monitor.
  • Page 39 Use the bracket provided in the kit to secure other peripheral devices by laying the device cable across the center of the bracket (1) and inserting the security cable through one of the two holes in the bracket (2). Use the hole in the bracket that best secures the peripheral device cable. Figure 2-30 Securing Peripheral Devices (Printer Shown) Thread the keyboard and mouse cables through the computer chassis lock.
  • Page 40 Screw the lock to the chassis in the thumbscrew hole using the screw provided. Figure 2-32 Attaching the Lock to the Chassis Insert the plug end of the security cable into the lock (1) and push the button in (2) to engage the lock.

  • Page 41: Front Bezel Security

    When complete, all devices in your workstation will be secured. Figure 2-34 Secured Workstation Front Bezel Security The front bezel can be locked in place by installing a security screw provided by HP. To install the security screw: Remove/disengage any security devices that prohibit opening the computer. Remove all removable media, such as compact discs or USB flash drives, from the computer.
  • Page 42 Remove the black screw on the front of the chassis behind the bezel. The screw is located next to the optical drive and is labeled "BEZEL." Figure 2-35 Retrieving the Front Bezel Security Screw Replace the front bezel. Install the security screw through the middle front bezel release tab and into the chassis to secure the front bezel in place.

  • Page 43: Appendix A Battery Replacement

    Battery Replacement The battery that comes with the computer provides power to the real-time clock. When replacing the battery, use a battery equivalent to the battery originally installed in the computer. The computer comes with a 3-volt lithium coin cell battery. WARNING! The computer contains an internal lithium manganese dioxide battery.
  • Page 44 Locate the battery and battery holder on the system board. NOTE: On some computer models, it may be necessary to remove an internal component to gain access to the battery. Depending on the type of battery holder on the system board, complete the following instructions to replace the battery.
  • Page 45 Type 3 Pull back on the clip (1) that is holding the battery in place, and remove the battery (2). Insert the new battery and position the clip back into place. Figure A-3 Removing a Coin Cell Battery (Type 3) NOTE: After the battery has been replaced, use the following steps to complete this procedure.

  • Page 46: Appendix B Electrostatic Discharge

    Electrostatic Discharge A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device. Preventing Electrostatic Damage To prevent electrostatic damage, observe the following precautions: Avoid hand contact by transporting and storing products in static-safe containers.

  • Page 47: Appendix C Computer Operating Guidelines, Routine Care And Shipping Preparation

    Computer Operating Guidelines, Routine Care and Shipping Preparation Computer Operating Guidelines and Routine Care Follow these guidelines to properly set up and care for the computer and monitor: Keep the computer away from excessive moisture, direct sunlight, and extremes of heat and cold. ●...

  • Page 48: Optical Drive Precautions

    Optical Drive Precautions Be sure to observe the following guidelines while operating or cleaning the optical drive. Operation Do not move the drive during operation. This may cause it to malfunction during reading. ● Avoid exposing the drive to sudden changes in temperature, as condensation may form inside the ●...

  • Page 49: Index

    Index access panel keyboard removing USDT removal 10 components 5 battery 37 USDT replacement 11 Windows Logo key 6 USDT bezel blanks 13 USDT computer access panel battery replacement 37 locks USDT front bezel 12 USDT cable lock 30 USDT hard drive 25 USDT front bezel 35 USDT optical drive 21 computer operating guidelines 41...

This manual is also suitable for:

Signageplayer mp8200s

Table of Contents