Asus TS300-E3 PS4 User Manual page 79

3 . 3 . 3 . 3 . Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4) Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4) Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4)
3 . Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4) Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4)
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
If you installed Serial ATA hard disk drives, you can create a RAID 0,
RAID 1, RAID 0+1, and software RAID 5 configuration using the Intel
Matrix Storage Technology or RAID 0, RAID 1 and RAID 0+1
configuration using the LSI MegaRAID
ICH7R Southbridge.
These connectors are set I D E
connect Serial ATA boot/data hard disk drives to these connectors. If
you intend to create a Serial ATA RAID set using these connectors, set
the C o n f i g u r e S A T A a s C o n f i g u r e S A T A a s C o n f i g u r e S A T A a s C o n f i g u r e S A T A a s item in the BIOS to [RAID]. See section C o n f i g u r e S A T A a s
"4.3.4 IDE Configuration" for details.
LAN2
P5MT Series SATA connectors
I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A
• You must install Windows
before using Serial ATA hard disk drives. The Serial ATA RAID
feature (RAID 0/RAID 1) is available only if you are using Windows
2000/2003.
• Use only two Serial ATA RAID connectors for each RAID 0 or RAID 1
set.
• When using the connectors in I D E
hard disk drive to the SATA1 or SATA2 connector. Refer to the table
below for the recommended SATA hard disk drive connections.
Serial ATA hard disk drive connection Serial ATA hard disk drive connection
Serial ATA hard disk drive connection Serial ATA hard disk drive connection Serial ATA hard disk drive connection
C o n n e c t o r C o n n e c t o r C o n n e c t o r C o n n e c t o r C o n n e c t o r
S A T A 1 / S A T A 2 S A T A 1 / S A T A 2 S A T A 1 / S A T A 2 S A T A 1 / S A T A 2 S A T A 1 / S A T A 2
S A T A 3 / S A T A 4 S A T A 3 / S A T A 4 S A T A 3 / S A T A 4 S A T A 3 / S A T A 4 S A T A 3 / S A T A 4
A S U S T S 3 0 0 - E 3 A S U S T S 3 0 0 - E 3 A S U S T S 3 0 0 - E 3 A S U S T S 3 0 0 - E 3 A S U S T S 3 0 0 - E 3
® utility embedded on the Intel
I D E I D E
I D E mode by default. In I D E I D E
SATA4
GND
RSATA_TXP4 RSATA_TXP2
RSATA_TXN4 RSATA_TXN2
GND
RSATA_RXP4 RSATA_RXP2
RSATA_RXN4 RSATA_RXN2
GND
SATA3
GND
RSATA_TXP3 RSATA_TXP1
RSATA_TXN3 RSATA_TXN1
GND
RSATA_RXP3 RSATA_RXP1
RSATA_RXN3 RSATA_RXN1
GND
®
2000 Service Pack 4 or Windows
I D E I D E
I D E I D E mode, connect the primary (boot)
S e t t i n g S e t t i n g S e t t i n g S e t t i n g S e t t i n g U s e U s e U s e U s e U s e
M a s t e r M a s t e r M a s t e r M a s t e r M a s t e r B o o t d i s k B o o t d i s k B o o t d i s k B o o t d i s k B o o t d i s k
S l a v e S l a v e S l a v e S l a v e S l a v e D a t a d i s k D a t a d i s k D a t a d i s k D a t a d i s k D a t a d i s k
I D E I D E
I D E mode, you can I D E
SATA2
GND
GND
GND
SATA1
GND
GND
GND
®
®
®
2003
®
4 - 1 1 4 - 1 1 4 - 1 1 4 - 1 1 4 - 1 1