Advertisement
INSTRUCTIONS - MAX
Properly Connecting Your
Surge Protector
To completely protect your equipment from
power surges, every wire leading into or out
of the equipment you want to protect must
be connected to the appropriate Panamax
surge protector. Damaging lightning and
power surges can get into your system
through any AC power or signal line (phone
lines, grounding wires, LAN cables, modem
cables, etc.) connected to your electrical
equipment.
Installation Procedures
1. Turn OFF the power to all equipment that
will be plugged into the unit.
2. Plug the protector into a properly ground-
ed AC outlet.
3. Once proper AC wiring and grounding has
been established via a green "Ground OK"
light, plug the equipment to be protected
into the AC outlets on the unit.
4. Note the position of the IN and OUT jack
on the ImagePro™ -EX unit. The IN jacks
are for the line connections that come from
the wall or floor jack. The OUT jacks are the
line connections to your connected equip-
ment.
MAX
ImagePRO-EX PRODUCT SPECIFICATIONS
®
AC SURGE PROTECTION
Line Voltage..................................................120VAC, 50/60Hz
Maximum Current Rating
MIP15........................................................................15A
MIP20........................................................................20A
EMI/RFI Noise Filtration............................65 dB (100KHz - 1 MHz)
Thermal Fusing..................................................................Yes
SurgeGate™ Circuitry...........................................................Yes
Overvoltage Shutoff..............................................146V ± 8V
Protect or Disconnect™ Circuitry..................................................Yes
Single Pulse Energy Dissipation....................................1650 Joules
Peak Impulse Current.............................................52,000 Amps
Voltage Protection Rating (UL1449 3rd Edition, 3,000A).............500V
Protection Modes.................................................L-N, L-G, N-G
Initial Clamping Level...................................................200 Volts
Surge Response Time...........................................<1 nanosecond
© 2009 Panamax, Inc.. MAX and the Panamax logo are registered US trademarks of Panamax. ImagePro, SignalPerfect, Firewall for Noise and Protect or Disconnect are trademarks of Panamax.
ImagePro
®
5. Plug the incoming LAN and/or telephone
line into the appropriate IN jack. The line
should now be connected between the wall
and the unit.
6. Plug the LAN and/or phone cord into the
appropriate OUT jack. Plug the other end
into the equipment to be protected.
7. One at a time, turn each piece of connect-
ed equipment ON and check for power and
correct operation.
Security Lock Installation
Security Lock – An equipment-to-protector
cord security lock is included with the
MAX
ImagePro™. This feature will allow
®
the user to attach and lock the connected
equipment's power cord to the protector.
This will insure that the protector remains
connected to the office equipment, which is
a useful tool for ensuring the validity of
service agreements.
1. Open the security lock and route both
power cords (surge protector and connect-
ed equipment) through the hasp.
2. Close the lock around the power cords.
Your equipment is now locked to the
MAX
ImagePro™.
®
TELEPHONE PROTECTION
Pins Protected..........................................RJ-11/45, pins 4,5
Protection Modes................................Metallic & Longitudinal
Clamping Level.............................................................260V
Capacitance....................................................30pf (approx.)
10/100 Base-T LAN PROTECTION
Pins Protected.....................................RJ-11/45, pins 1,2,3,6
Protection Modes.......................................All pins to ground
Clamping Level.................................................................7V
EX Series (15Amp and 20Amp)
™
AC line from
connected
equipment.
CONTACTING PANAMAX
For product and warranty information or
other general information, please contact
PANAMAX Customer Relations at:
Email: custrelations@panamax.com
Web: www.panamax.com
Fax: 707-283-5901
Toll Free:800-472-5555 or
Phone: 707-283-5900,
7:30 AM - 4:30 PM, PST
1690 Corporate Circle, Petaluma, CA 94954
800-472-5555 • www.panamax.com
INS00812 REV. C
7/09
Advertisement
