Panamax MIP20 Instructions

INSTRUCTIONS - MAX
Important Safety Points
Panamax surge protectors and the connect-
ed equipment must be indoors in a dry
location and in the same building. Although
your Panamax protector is very durable, the
internal components are not isolated from
the environment. Do not install any
Panamax product near heat emitting appli-
ances such as a radiator or heat register.
Do not install this product where excessive
moisture is present.
It is not uncommon for a building to be
improperly grounded. In order to protect
your equipment, Panamax products must
be plugged into a properly grounded 3-wire
outlet. Additionally, building wiring and
grounding must conform to applicable NEC
(USA) or CEC (Canada) codes for the
Panamax warranty to be valid.
Do not use 2-blade ground adapters with
this product. If an extension cord is
required, use only Panamax #GEC1410. If
your surge protector indicates a Line Fault,
do not use the product. Call your electrician
to correct the building's wiring.
CAUTION – Do not install this device
if there is not at least 10 meters (30 feet)
or more of wire between the electrical
outlet and electrical service panel.
Features
MIP-20A-EX
20 Amp AC configured receptacles
Ground OK Indicator light
Protection OK Indicator light
Three-stage, GFCI
Compatible filter circuit
provides high levels of
Normal and Common
mode EMI/RFI noise
•
filtration
•
Eight foot power cord
15 amp plug
20 amp plug
MIP-15A-EX
MIP-20A-EX
ImagePRO
®
Power Filtration and Surge
Protection for Digital Office
Equipment
The MAX ImagePRO™ EX Series is
®
designed to provide clean power and pro-
tect digital office equipment from a variety
of undesirable power conditions. Digital
components are prone to operating at unac-
ceptable performance levels when exposed
to EMI/RFI interference or power fluctua-
tions (surges and spikes). Without the
proper protection,digital equipment may
experience data loss, lock-ups or even cir-
cuit damage. The MAX ImagePRO-EX
®
series will protect your digital office equip-
ment from a combination of power prob-
lems including, normal and common mode
EMI/RFI noise interference, ground noise,
surges, spikes, and sustained over-voltages.
The MAX ImagePro™-EX is available in
®
15-Amp (MIP-15A-EX) and 20-Amp (MIP-
20A-EX) models. This includes:
Firewall for Noise™ Circuitry – This
technology provides enhanced Neutral-to-
Ground Noise Filtration for your digital
office equipment. EMI/RFI noise can
contaminate the equipment safety ground,
which in turn will contaminate the connect-
ed digital equipment, and prevent it from
operating at peak performance levels.
LAN Protection
2 pairs of RJ-45
bi-directional connectors
(2 LAN cables included)
•
Unsafe Power Indicator light
•
Line Fault Indicator light
•
•
-
EX Series (15Amp and 20Amp)
™
GFCI Compatibility
This circuit features an improved 2-satge
common-mode architecture that provides
compatibility for GFCI's ans NEC article
250.6.
Firewall for Noise™ - circuitry prevents
EMI/RFI noise from contaminating the con-
nected digital equipment through the
ground wiring.
Automatic Voltage Monitoring (AVM )–
This power monitoring system acts as a
gate to prevent unsafe voltages from dam-
aging sensitive electronic equipment. It
automatically detects a prolonged over-volt-
age and disconnects the power to the con-
nected equipment, then reconnects it when
the power returns to a safe level. It even
protects the MAX
®
Wiring Fault Safety Shutoff – This technol-
ogy will detect a miswired wall receptacle or
an open-ground by monitoring the voltage
between neutral and ground. If an unsafe
condition exists, the MAX
disconnect the power from the connected
equipment.
Telephone Protection
2 pairs of RJ-11
In/Out connectors
•
(2 telco cable included)
•
Two rubber strips running the length of the product
provide a non-slip grip and prevent marring surface.
SignalPerfect™ Telephone Line Protection
Two pairs of RJ-11 phone jacks are avail-
able to protect a single-line telephone
modem (pins 4,5 protected) with fuseless
Auto-Resetting technology and optimized
circuitry to ensure a clean, clear signal.
Ethernet LAN Protection – Two pairs of
RJ-11/45 jacks are available to protect one
Ethernet 10/100 Base-T network connection
(all pins protected).
Diagnostic lights -
Power ON and Protection OK- (green)
normally ON - indicates that the surge
protector is functioning properly, power
is on, and it is protecting all connected
equipment.
ImagePro™ unit. Ground OK – (green) normally ON -
indicates that the wall outlet is properly
wired.
Line Fault – (red) normally OFF - when
lit, indicates that the wall outlet is
ImagePro™ will improperly wired.
®
Unsafe Power – (red) normally OFF –
when lit, indicates that incoming voltages
are unsafe and the surge protector has
disconnected the power to protect your
equipment or that there is a wiring fault.
Separate protection
circuits for 10/100 BaseT
Ethernet and telephone
•
•
Three Always-on AC outlets
(20 Amp MIP20)
(15 Amp MIP15)
Wall mountable
(Velco strips
included).
Includes security
lock to prevent theft.
•
INS00812 REV. C 7/09