BIXOLON SRP-500C - Color Inkjet Printer Installation Manual

KN06-00002A (Rev.1.0)
◈ Information
This Installation Guide includes a brief outline of information necessary for
product installation. For more detailed installation information, please refer to the
user manual in the enclosed CD. The contents of the CD include the following.
1. Manual: User Manual, Code Chart, Control Commands
2. Drivers: Windows Drivers, OPOS Drivers
3. Utilities: a logo download tool
◈ Components
Cable Cover
SRP-500
AC/DC Adaptor
◈ Connecting the cables
1. Plug the power cord into the AC Adaptor, and then plug the AC Adaptor into
the power connector of the printer
2. Turn off the printer and the host ECR (host computer).
3. Check the interface cable (Serial, Parallel, USB), and connect the interface
connector cable accordingly.
4. Plug the drawer kick-out cable into the drawer kick-out connector on the
printer.
Interface
connector
Interface cable
(Serial/Parallel/USB)

◈ Installing the Ink Cartridge

1. Turn on the printer.
2. Remove new ink cartridge from the pouch and remove the tape affixed to the
front side.
3. Open front cover of the printer and pull the cartridge holder forward.
4. Take out old ink cartridge(s) and place new cartridge(s) into carriage. Hold
round tab to ensure clean installation.
Black cartridges go into left carriage, and color cartridges go into right
carriage. Tab faces front of printer.
5. Close cartridge holder(s) and front cover.
Tab
Tape
Metallic connector
area
※ Note
The ink drop counter is automatically reset when the ink cartridge is installed.
Paper Roll Ink Cartridge
Power cord Installation Guide
Drawer kick-out
connector
Power connector
Adaptor
Power cord
Drawer kick-
out cable
Front cover
Cartridge holder
Printer Installation Guide
INKJET PRINTER

◈ Installing the Paper Roll

Procuct Installation CD Procuct Installation CD Procuct Installation CD
◈ Using the Operation Panel
CD
• Power (LED)
When turning on the power, a green LED will be lit.
• Error (LED)
When an error occurs, a red LED will be lit. (e.g. no paper,
cover ajar, etc.)
• Cartridge (LED)
The LED will be lit when the ink has run out or the cartridge is
removed. Check the status of the right cartridge with the right
LED, and the left cartridge, with the left LED. For
monochrome, the left LED is used. The left cartridge is black,
and the right cartridge is color.
• Clean (Button)
Use this button to clean the ink cartridge heads.
• Feed (Button)
Press the FEED button once to discharge extra paper. Holding
down the FEED button will discharge paper continuously until
the button is released.
◈ Setting the DIP Switches
Changing Dip Switch settings must be done when the printer is off. Any changes
done while the printer is on will not be processed.
1. Serial Interface
• DIP Switch 1
SW Function
1-1
Emulation
1-2
1-3 Auto Cutter
1-4 Cartridge
1-5 Density
1-6 Special Function
1-7 Near-End Sensor Status
1-8 Low Ink Check
• DIP Switch 2
SW Function
2-1 Data Receive Error
2-2
2-3 Handshaking
2-4 Data Length
2-5 Parity Check
2-6 Parity Selection
2-7
Baud Rate Selection
2-8
2. Parallel / USB Interface
• DIP Switch 1
SW Function
1-1
Emulation
1-2
1-3 Auto Cutter
1-4 Cartridge
1-5 Density
1-6 Special Function
1-7 Near-End Sensor Status
1-8 Low Ink Check
1. Open the rear cover.
2. Insert a new paper roll, making sure to
align it properly.
3. Pull out a small amount of paper, and
close the rear cover.
ON
Refer to the following table 1
Enable
One cartridge Two cartridges
*1)
Bold
*2)
Enable
Enable
Disable
ON
Print ?
Reserved
DTR/DSR XON/XOFF
7 bits
Enable
EVEN
Refer to the following table 2
ON
Refer to the following table 1
Enable
One cartridge Two cartridges
*1)
Bold
*2)
Enable
Enable
Disable
SRP-500
OFF Default
OFF
OFF
Disable OFF
OFF
Normal OFF
Disable OFF
Disable OFF
Enable OFF
OFF Default
Ignore OFF
OFF
OFF
8bits OFF
Disable OFF
ODD OFF
OFF
OFF
OFF Default
OFF
OFF
Disable OFF
OFF
Normal OFF
Disable OFF
Disable OFF
Enable OFF