Related Manuals for Panduit ATLONA OMEGA AT-OME-SW21-TX
Summary of Contents for Panduit ATLONA OMEGA AT-OME-SW21-TX
- Page 1 HDBaseT Transmitter with USB-C and HDMI Inputs plus USB Hub Atlona Manuals AT-OME-SW21-TX Switcher / Transmitter...
- Page 2 Version Information Version Release Date Notes May 2025 Factory release AT-OME-SW21-TX...
- Page 3 Sales, Marketing, and Customer Support Main Office International Headquarters Atlona Incorporated Atlona International AG 70 Daggett Drive Tödistrasse 18 San Jose, CA 95134 8002 Zürich United States Switzerland Office: +41 43 508 4321 Office: +1.408.962.0515 (US/International) Sales and Customer Service Hours Sales and Customer Service Hours Monday - Friday: 6:00 a.m.
- Page 4 Important Safety Information 9. Do not defeat the safety purpose of a polarized CAUTION or grounding-type plug. A polarized plug has two RISK OF ELECTRIC SHOCK blades with one wider than the other. A grounding DO NOT OPEN type plug has two blades and a third grounding CAUTION: TO REDUCT THE RISK OF prong.
- Page 5 Table of Contents Introduction Features Package Contents Panel Description Installation Captive Screw Connections RS-232 Mounting Instructions Cable Guidelines Connection Instructions IP Modes DHCP Static Connection Diagram Control Front Panel RS-232 TCP/IP WebGUI Front Panel Settings Input Selection RS-232 Settings IP Settings Front Panel Display Timer WebGUI AV Settings...
- Page 6 Introduction The Atlona AT-OME-SW21-TX is a compact, versatile switcher and HDBaseT transmitter with USB-C and HDMI ® ® inputs. It sends video up to 4K/60 4:2:0, plus embedded audio, control, and USB 2.0 over distances up to 330 feet (100 meters). Part of the Omega™ Series of integration products for modern AV communications and collaboration, the OME-SW21-TX features mirrored HDMI and HDBaseT outputs and is HDCP 2.3 compliant.
- Page 7 Panel Description AT-OME-SW21-TX LINK OMEGA DISPLAY INPUT DOWN ENTER RESET AT-OME-SW21-TX RX TX USB-C IN HDMI IN HDMI OUT HDBaseT OUT HOST RS-232 PWR and LINK LEDs HDMI OUT Illuminates green when receiving power and amber Connect an HDMI cable from here to an HDMI when receiving signal.
- Page 8 Installation RS-232 Connection A 3-pin captive screw connector has been included for RS-232. Pin out will be determined by the RS-232 cable and connect as RX (receive), TX (transmit) and (ground). Mounting Instructions The .OME-SW21-TX includes two mounting brackets and four mounting screws, which can be used to attach the unit to any flat surface.
- Page 9 Installation 4. Mount the unit using the oval-shaped holes, on each mounting bracket. If using a drywall surface, a #6 drywall screw is recommended. E - S - O M 2 4 V I P M 2 3 2 R S - S E T - S K T P U...
- Page 10 Installation Connection Instructions 1. Connect an HDMI source to the HDMI IN port. 2. Connect a USB-C source to the USB-C IN port, using the included cable. 3. Connect an HDMI cable from the output port to an HDMI display. 4.
- Page 11 Installation IP Modes DHCP By default, the AT-OME-SW21-TX is set to DHCP mode. In this mode, when the AT-OME-SW21-TX is connected to the Local Area Network (LAN), it will automatically be assigned an IP address by the DHCP server (if available). The IP address can be seen on the front panel OSD.
- Page 12 Installation Connection Diagram Laptop 21 -T E- SW A T- E - S SE T TE R IN PU PL A D IS LI N AT-OME-SW21-TX VI CE AT-OME-EX-RX Confidence Monitor Interactive Display AT-OME-SW21-TX...
- Page 13 Control The product has CEC display control over HDMI. More information can be found in the Web Server section. Front Panel The unit has a front panel display and buttons to view and set up basic settings. See the Front Panel section for more information.
- Page 14 Front Panel The unit has a front panel display and buttons to view and set up basic settings. Any button can awaken the front panel, but to avoid triggering secondary functions, it is recommended to use the ENTER button. At any time during use, the BACK button can be used to navigate to previous menu options.
- Page 15 Front Panel To reset the IP of the unit, use the following steps: Setting Setting [ RS232 BAUD ] AT-OME-SW21-TX RS232 BAUD Input: [USB-C] IP MODE IP MODE ENTER ENTER DOWN ENTER IP RESET IP RESET IP reset back ENTER Front Panel Display Timer To conserve the front panel display, the unit has a default timer of 30 seconds before it is turned off.
- Page 16 Web Server The OME-SW21-TX includes a built-in webGUI, which allows easy remote management and control of all features. Follow the instructions below to access the webGUI. 1. Make sure that an Ethernet cable is connected between the LAN port on the OME-SW21-TX and the network. 2.
- Page 17 Web Server AV Settings Select A/V Settings from the top navigation to adjust routing and video settings. Video Input Selection - Use the drop-down menu to switch USB Type-C or HDMI inputs. HDMI Output +5V - When set to Always On, it will keep the 5V pin on the HDMI output port live. When set to On When Signal Present, it will only send the 5V hot plug when receiving an input signal.
- Page 18 Web Server Display Select Display from the top navigation to adjust display control settings. Power - Press to send the CEC power on or off command out through the HDMI port of the connected receiver. NOTE: When connected to a compatible receiver with display control, all the (e.g.
- Page 19 Web Server TCP/IP Settings of Controlled Device (only available when IP is selected) IP Mode - Toggle login mode between Non-Login and Login. If set to Login, a username and password will be required to control the controlled device via TCP/IP. IP Address - Sets to the IP of the controlled device/display.
- Page 20 Web Server RS-232 Select RS-232 from the top navigation to adjust the zone control parameters for the RS-232 port. RS-232 Parameter Setting RS232 over HDBaseT - Select the baud rate, data bit, parity, and stop bit to match the receiver’s parameters. Defaults are 115200, 8, None, and 1.
- Page 21 Web Server EDID Select EDID from the top navigation to save/load EDIDs. EDID EDID Settings - Use the drop down menu to select from default (highest common resolution between source and display), 9 internal EDIDs, and 2 previously saved EDIDs. EDID Saved - Select the HDMI OUT or HDBT OUT to save to EDID memory slot.
- Page 22 Web Server Select USB from the top navigation for USB routing. USB Host Manual - Select which host will be used. Select between USB-C, the local USB Host , or the connected (USB 1) receiver’s USB Host (remote) Follow Video - Sets the USB hosts to follow the video input selection.
- Page 23 Web Server OCS-900 Atlona IP Sensor - Select the Add button. A pop up will appear. Fill in the IP address of the OCS-900N sensor and press Add. The Sensor will be added to the page. Multiple OCS-900Ns can be added to the room using the same steps.
- Page 24 Web Server User Select Config from the top navigation to update the admin password. User Old Username - Type in the current username of the OME-SW21-TX. New Username - Update the username for the unit. Old Password - Type in the current password of the device. New Password - Enter a new password.
- Page 25 Web Server System Select System from the top navigation to adjust relay, network, or system options. Network MAC Address - Displays the MAC address of the unit. IP Mode - Switch between static and DHCP IP modes. IP, Netmask, Gateway - This will display the unit’s current DHCP IP settings. When set to static, fill in the IP address, netmask, and gateway.
- Page 26 Web Server System Front Panel Lock - Lock or unlock the front panel buttons. Reset to Default- Press the Factory Default button to set the unit back to all factory settings, including IP mode. Firmware Update - Use the choose file button to search the local PC for the firmware file. Once selected, press the Update button to start the firmware update.
- Page 27 Web Server Tools Select Tools to open the HDBaseT cable test and API command field page. The HDBaseT test will check extender versions, cable status and length, and Video Quality. HDBaseT Channel Cable Test HDBaseT Zone - Use the start/stop button to run or cancel the HDBaseT signal testing. The webGUI will remain active until the testing stops.
- Page 28 Web Server API Command API Command - Commands can be entered here to be sent to the unit. Send - Press this button to transmit the command to the unit. Log - This will display a command log of any and all commands sent. AT-OME-SW21-TX...
- Page 29 Appendix Specifications Video Signal Type Input - DisplayPort Alternate Mode (USB-C), HDMI Output - HDBaseT, HDMI Copy Protection HDCP 1.4/2.2/2.3 Pixel Clock 600MHz (300MHz over HDBaseT) UHD/HD/SD 4096×2160(DCI)@60/50/30/25/24Hz 1920x1080i@30/29.97/25Hz 3840×2160(UHD)@60/50/30/25/24Hz 1280x720p@60/59.94/50/30Hz 2560x1440@30Hz 720x576i/p@50Hz 1920x1080p@60/59.94/50/30/29.97/25 720x480i/p@60Hz /24/23.98Hz VESA 2560×1600 1280×800 All resolutions are 60Hz 2048x1536 1366×768 1920×1200...
- Page 30 Appendix Indicators, Buttons, and Controls PWR indicator 1 - LED, green LINK indicator 1 - LED, yellow Buttons DISPLAY, INPUT, UP, DOWN, 5 - momentary, tact-type ENTER Reset 1 - recessed, momentary Resolution / Distance 4K/UHD - Feet / Meters 1080p - Feet / Meters USB-C HDMI IN/OUT...
- Page 31 International atlona.com 408.962.0515 41.43.508.4321 • • 35358-R1...
Need help?
Do you have a question about the ATLONA OMEGA AT-OME-SW21-TX and is the answer not in the manual?
Questions and answers