Advertisement
Quick Links
Advertisement
Related Manuals for Vivo MOUNT-V002G
Summary of Contents for Vivo MOUNT-V002G
- Page 1 Mechanical Dual Single Monitor Wall Mount MOUNT-V002G Assembly Manual...
- Page 2 If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact our product support team at 309-278-5303 or help@vivo-us.com for further assistance. Check carefully to make sure there are no missing or defective parts. Failure to report missing parts within 30 days may result in denial of free replacement.
- Page 3 Package Contents B (x2) C (x1) A (x2) D (x2) Wall Bracket Upper Arm Lower Arm VESA Bracket E (x4) F (x3) Cable Cover Screw Cover Included Hardware & Tools S-A (x2) M-A (x8) M-B (x8) W-A (x3) W-B (x3) M8x30mm M4x12mm M5 Washer...
- Page 4 Assembly Steps STEP 1 Option 1: Wood Stud Installation Pre-Drilling Instructions Drill mounting holes using infographic shown Drill Bit: 3/16” (4.5mm) Place the Wall Bracket (C) at the desired location and mark the drilling holes with a pencil. Use of a stud finder and level is recommended.
- Page 5 Option 2: Concrete Installation Pre-Drilling Instructions Drill mounting holes using infographic shown Drill Bit: 3/8” (10mm) Place the Wall Bracket (C) at the desired location and mark the drilling holes with a pencil. Use of a stud finder and level is Hole Depth: recommended.
- Page 6 STEP 2 Insert the Lower Arms (B) into the Wall Bracket (C) and insert the Upper Arms (A) into the Lower Arms. Tighten the set screws with the flat end of the 4mm Allen Wrench (T-A).
- Page 7 STEP 3 Insert VESA Brackets (D) into the Upper Arms (A). Ensure the open holes are facing up. Secure the VESA Brackets (D) to the Upper Arms (A) using the M8x30mm Screws (S-A) and 5mm Allen Wrench (T-B).
- Page 8 STEP 4 Insert two M4x12mm Screws (M-A) with M5 Washers (M-B) into the top two holes of each monitor, leaving 3mm of threading exposed. Place the monitors onto the VESA Brackets (D). 2 Person Mounting Recommended Insert the remaining M4x12mm Screws (M-A) with M5 Washers (M-B) into the monitors. Tighten all screws using the Phillips end of the 5mm Allen Wrench (T-B).
- Page 9 STEP 5 Adjusting Monitor Height Position Mount Arm Turn 10-20x to Set Monitor Height Position the arm horizontally, as shown above, and firmly hold in Turn 5mm Allen Wrench (T-B) 10-20 times place. to obtain proper support for your monitor. Use the guide below to adjust the tension according to the amount of counterbalance Insert...
- Page 10 STEP 6 Manage cables using Cable Covers (E). Slide Cable Covers Align Prongs to Install Forward to Remove Press the prongs on the Covers (E) into the slots on the underside of the arm, then slide down to lock in place. DO NOT PULL COVERS DOWN Doing so will damage the covers...
- Page 11 Tilt Adjustment To adjust the tilt, loosen the VESA Bracket (D) screw using the 5mm Allen Wrench (T-B). When at the desired angle re-tighten the screw to secure. The M8x30mm Screws (S-A) may need to be loosened slightly to allow swinging. Rotate as desired.
- Page 12 Need Help? We’re Here For You Monday-Friday from 7am-7pm CST Saturday 8am-4pm CST Email Us Chat with Live Agent Give Us a Call help@vivo-us.com www.vivo-us.com 309-278-5303 ext. 1 FOR MORE GREAT VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: WWW.VIVO-US.COM VIVO-us @vivo_us @VIVOus VIVO...
Need help?
Do you have a question about the MOUNT-V002G and is the answer not in the manual?
Questions and answers