Table of Contents
Advertisement
Quick Links
P4MDF/P4MDFT
USER'S MANUAL
M/B For Socket 478 Pentium 4 Processor
NO. G03-P4MDF
Rev:1.0
Release date: Dec. 2003
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for JETWAY P4MDFTR1A
Summary of Contents for JETWAY P4MDFTR1A
- Page 1 P4MDF/P4MDFT USER'S MANUAL M/B For Socket 478 Pentium 4 Processor NO. G03-P4MDF Rev:1.0 Release date: Dec. 2003 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
-
Page 2: Table Of Contents
TABLE OF CONTENT USER’S NOTICE ......................ii MANUAL REVISION INFORMATION ................ii COOLING SOLUTIONS ....................ii CHAPTER 1 INTRODUCTION OF P4MDF/P4MDFT FEATURE OF MOTHERBOARD ..................2 SPECIFICATION........................3 PERFORMANCE LIST ......................4 LAYOUT DIAGRAM & JUMPER SETTING ..............5 CHAPTER 2 HARDWARE INSTALLATION HARDWARE INSTALLATION STEPS ................ -
Page 3: User's Notice
USER’S NOTICE COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER. THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE P4MDF/P4MDFT MOTHER- BOARD AND WE DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME WITHOUT NOTICE. -
Page 4: Chapter 1 Introduction Of P4Mdf/P4Mdft
MagicTwin software. You can add immediately additional user station to the single system and turn one PC into two. System Requirement Jetway MagicTwin Motherboard: 2 x PS/2 Y-cable Install CD (Driver and MagicTwin) -
Page 5: Feature Of Motherboard
1-1 Feature of motherboard The P4MDF/P4MDFT motherboard is design for use Intel Pentium 4 Processor in 478 Pin Package Processor with the VIA P4M266A(CE) Chipset delivers a high performance and professional desktop platform solution. Which utilize the Socket 478 design and the memory size expandable to 2.0GB. -
Page 6: Performance List
Spec Description ∗ Mini ATX form factor 6 layers PCB size: 18.5x25.5cm Design ∗ VIA P4M266A North Bridge Chipset Chipset ∗ VIA VT8235 South Bridge Chipset ∗ Support Intel Pentium 4 478 Pin package utilizes Flip-Chip Pin CPU Socket (mPGA478B Socket) Grid Array (FC-PGA2) package processor ∗... -
Page 7: Layout Diagram & Jumper Setting
The following performance data list is the testing result of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users (the different Hardware & Software configuration will result in different benchmark testing results.) Performance Test Report CPU:... - Page 8 6-Channel Speaker PRINT Center/Base PS/2 Mouse REAR Speaker PS/2 Keyboard Front Speaker COM1 USB1 USB1: (2xport for P4MDF, 1xport for P4MDFT) Winbond 83697HF Chip K/B Power ON Jumper (JP1) External Remote Control (JP2) ATX 12V Power Conn. ATX Power Conn. PS2 KB/Mouse Port DIMM Socket X2 Serial Port COM2 Connector...
-
Page 9: Chapter 2 Hardware Installation
JBAT CMOS RAM Clear 3-pin Block Keyboard/Mouse Power On Function 3-pin Block JP3/JP4 USB Power On Enable/Disabled 3-pin Block Connectors Connector Name Description Page ATXPWR ATX Power Connector 20-pin Block P.12 ATX12V ATX 12V Power Connector 4-pin Block P.13 PS2KBMS1 PS/2 Mouse &... -
Page 10: Hardware Installation Steps
2-1 Hardware installation Steps Before using your computer, you had better complete the following steps: 1. Check motherboard jumper setting 2. Install CPU and Fan 3. Install System Memory (DIMM) 4. Install Expansion cards 5. Connect IDE and Floppy cables, Front Panel /Back Panel cable 6. -
Page 11: Install Cpu
1-2 closed K/B Power ON Disabled (Default) 2-3 closed K/B Power ON Enabled (3) USB Power On function Enabled/Disabled: JP3/JP4 1-2 closed USB Power On Disabled (Default) 2-3 closed USB Power On Enabled JP4 1-2 closed USB Power On Disabled (Default) 2-3 closed USB Power On Enabled 2-3 Install CPU 2-3-1 Glossary... -
Page 12: About Intel Pentium 4 478-Pin Cpu
Processor - the "central processing unit" (CPU); the principal integrated circuit used for doing the "computing" in "personal computer" Front Side Bus Frequency - the working frequency of the motherboard, which is generated by the clock generator for CPU, DRAM and PCI BUS. CPU L2 Cache - the flash memory inside the CPU, normal it depend on CPU type. -
Page 13: Expansion Card
This motherboard provides 184-pin DDR DUAL INLINE MEMORY MODULES (DIMM) sites for DDR memory expansion available from minimum memory size of 64MB to maximum memory size of 2.0GB DDR SDRAM. Valid Memory Configurations Bank 184-pin DDR DIMM Total Memory Bank 0, 1 (DDR1) DDR266/DDR200 DDR DRAM Module 64MB∼1.0GB Bank 2, 3 (DDR2) -
Page 14: Procedure For Expansion Card Installation
WARNING! Turn off your power when adding or removing expansion cards or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards. 2-5-1 Procedure For Expansion Card Installation 1. Read the documentation for your expansion card and make any necessary hardware or software setting for your expansion card such as jumpers. -
Page 15: Agp Slot
√ Slot 1 √ Onboard USB 1 √ Onboard USB 2 √ AC97/MC97 IMPORTANT! If using PCI cards on shared slots, make sure that the drivers support “Shared IRQ” or that the cards don’t need IRQ assignments. Conflicts will arise between the two PCI groups that will make the system unstable or cards inoperable. - Page 16 Without this connector might cause system unstable because the power supply can not provide sufficient current for system. Pin 1 PS/2 Mouse & PS/2 Keyboard Connector : PS2KBMS1 The connectors for PS/2 keyboard and PS/2 Mouse. It can connect with a Y-Cable which can support 2 Keyboard and 2 Mouse for 2 user function.
- Page 17 Center/Base REAR Speaker Front Speaker PS/2 COM1 USB1 Keyboard USB1: (2xport for P4MDF, 1xport for P4MDFT) (10) Floppy drive Connector (34-pin block): FDD This connector supports the provided floppy drive ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to the floppy drives. Pin 1 Floppy Drive Connector (11) Primary IDE Connector (40-pin block): IDE1...
-
Page 18: Headers
IDE 2 Pin 1 Secondary IDE Connector • Two hard disks can be connected to each connector. The first HDD is referred to as the “Master” and the second HDD is referred to as the “Slave”. • For performance issues, we strongly suggest you don’t install a CD-ROM or DVD-ROM drive on the same IDE channel as a hard disk. - Page 19 USB _ VC C USB _ VC C G ND G ND AUD _ L AUD _ R MIC _ R E F SMIC G ND IDE Activity LED: JP7 This connector connects to the hard disk activity indicator light on the case. Speaker connector: SPEAK This 4-pin connector connects to the case-mounted speaker.
- Page 20 (10) Wake On-LAN Headers (3-pin) : WOL This connector connects to a LAN card with a WAKE ON-LAN output. This connector power up the system when a wake up signal is received through the LAN card. NOTE: This feature requires that Wake On LAN or Ring In Wake up is enabled. Wake-On-LAN Headers (11) FAN Headers (3-pin) : SFAN1, SYSFAN, CPUFAN These connectors support cooling fans of 350mA (4.2 Watts) or less, depending on the...
- Page 21 (13) CD Audio-In Headers (4-pin) : CD _ IN CD _ IN are the connectors for CD-Audio Input signal. Please connect it to CD-ROM CD-Audio output connector. C DIN R -C H G ND G ND L-C H CD Audio-In Headers (14) LCD Display panel connect Headers (11-pin) : JW_LCDFP This headers is the connector for LCD Display Panel, it transfer the data from motherboard to display panel.
-
Page 22: Starting Up Your Computer
2-7 Starting Up Your Computer 1. After all connection are made, close your computer case cover. 2. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V∼240V or 110V∼120V depending on your country’s voltage used. -
Page 23: Entering Setup
Chapter 3 Introducing BIOS The BIOS is a program located on a Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization. -
Page 24: The Main Menu
3-3 The Main Menu Once you enter Award BIOS CMOS Setup Utility, the Main Menu (Figure 3-1) will appear on the screen. The Main Menu allows you to select from fourteen setup functions and two exit choices. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu. -
Page 25: Standard Cmos Features
Load Optimized Defaults Use this menu to load the BIOS default values these are setting for optimal performances system operations for performance use. Load Standard Defaults Use this menu to load the BIOS default values for the stable performance system operation that are factory settings for normal use. -
Page 26: Advanced Bios Features
The time format is <hour><minute><second>. Primary Master/Primary Slave Secondary Master/Secondary Slave Press PgUp/<+> or PgDn/<–> to select Manual, None, Auto type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. - Page 27 Allows you to choose the VIRUS Warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep. Disabled (default) No warning message to appear when anything attempts to access the boot sector or hard disk partition table.
-
Page 28: Advanced Chipset Features
Typematic Delay (Msec) Sets the delay time after the key is held down before is begins to repeat the keystroke. The settings are 250, 500, 750, and 1000. Security Option This category allows you to limit access to the system and Setup, or just to Setup. The system will not boot and access to Setup will be denied if the System correct password is not entered at the prompt. -
Page 29: Dram Timing Settings
System BIOS Cacheable Selecting Enabled allows caching of the system BIOS ROM at F0000h-FFFFFh, resulting in better system performance. However, if any program writes to this memory area, a system error may result. The settings are: Enabled and Disabled. Memory Hole You can reserve this area of system memory for ISA adapter ROM. -
Page 30: Pci Timing Settings
3-6-2 AGP Timing Settings CMOS Setup Utility – Copyright(C) 1984-2003 Award Software AGP Timing Settings VGA Share Memory Size Item Help AGP Transfer Aperture Size AGP Mode Auto AGP Driving Control Auto Menu Level >> * AGP Driving Value AGP Fast Write Disabled AGP Master 1 WS Write Enabled... -
Page 31: Onchip Ide Function
Please refer to section 3-7-1 OnChip Device Function Please refer to section 3-7-2 Onboard Super IO Function Please refer to section 3-7-3 Init Display First This item allows you to decide to activate whether PCI Slot or AGP VGA first. The settings are: PCI Slot, AGP Slot. -
Page 32: Onchip Device Function
Block mode is also called block transfer, multiple commands, or multiple sector read/write. If your IDE hard drive supports block mode (most new drives do), select Enabled for automatic detection of the optimal number of block read/writes per sector the drive can support. The settings are: Enabled, Disabled. -
Page 33: Power Management Setup
CMOS Setup Utility – Copyright(C) 1984-2003 Award Software Onboard Super IO Function Onboard FDD Controller Enabled Item Help Onboard Serial Port 1 3F8/IRQ4 Onboard Serial Port 2 2F8/IRQ3 UART2 Mode Normal Menu Level >> RxD, TxD Active Hi, Lo IR Duplex Mode Half Use IR Pins IRRX/IRTX... -
Page 34: Pm Wake Up Events
The Power Management Setup allows you to configure your system to most effectively save energy saving while operating in a manner consistent with your own style of computer use. CMOS Setup Utility – Copyright(C) 1984-2003 Award Software Power Management Setup ACPI Function Enabled Item Help... -
Page 35: 3-8-1.1 Irqs Activities
CMOS Setup Utility – Copyright(C) 1984-2003 Award Software Wake Up Events Item Help LPT & COM LPT/COM HDD & FDD PCI Master Menu Level >> Wake-Up on Ring/LAN Disabled Wake-Up on PCI PME Disabled PS2 KB Wakeup Selection Hot Key Wake-Up on Hot Key (PS2 KB) Power Key Wake-Up on RTC Alarm... -
Page 36: Irq Resources
This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings. -
Page 37: Pc Health Status
CMOS Setup Utility – Copyright(C) 1984-2003 Award Software IRQ Resources IRQ3 assigned to PCI Device Item Help IRQ4 assigned to PCI Device IRQ5 assigned to PCI Device IRQ7 assigned to PCI Device Menu Level >> IRQ9 assigned to PCI Device IRQ10 assigned to PCI Device... -
Page 38: Load Standard/Optimized Defaults
This section is for setting CPU Frequency/Voltage Control. CMOS Setup Utility – Copyright(C) 1984-2003 Award Software Miscellaneous Control CPU Clock Ratio Item Help Auto Detect PCI/DIMM Clock Enabled Spread Spectrum Disabled ** Current Host/PCI Clock is Menu Level > Host/PCI Clock at Next Boot is ** Current DRAM Clock is DRAM Clock at next Boot is CPU Vcore Select... -
Page 39: Set Supervisor/User Password
Load Standard Defaults When you press <Enter> on this item, you get confirmation dialog box with a message similar Load Standard Defaults (Y/N)? N Pressing <Y> loads the BIOS default values for the most stable, minimal-performance system operations. Load Optimized Defaults When you press <Enter>... -
Page 40: Magic Install Supports Windows 9X/Me/Nt4.0/2000/Xp
Check your package and there is A MAGIC INSTALL CD included. This CD consists of all DRIVERS you need and some free application programs and utility programs. In addition, this CD also include an auto detect software which can tell you which hardware is installed, and which DRIVERS needed so that your system can function properly. - Page 41 AGPVXD : VIA AGPVXD DRIVER IS TO BE INSTALLED, IF YOU ARE USING AN AGP VGA CARD, VIAGART.VXD WILL PROVIDE SERVICE ROUTINES TO YOUR VGA DRIVER AND INTERFACE DIRECTLY TO HARDWARE, PROVIDING FAST GRAPHIC ACCESS IRQ ROUTING : VIA PCI IRQ MINIPORT DRIVER IS TO BE INSTALLED UNDER WIN98 ONLY, IT WILL FIX PCI IRQ ROUTING SEQUENCE INF : VIA REGISTRY DRIVER IS TO BE INSTALLED UNDER WINDOWS...
-
Page 42: Vga Install Prosavage Ddr Vga Driver
7. Click NEXT to Install VIA AGP VXD Driver 8. Click NEXT to Install VIA IRQ Routing Mini port Driver 9. Click Finish to restart computer 4-2 VGA install Prosavage DDR VGA Driver For WINDOWS 9X/ME/NT4.0/2000/XP 1. Click VGA when MAGIC INSTALL MENU Click NEXT When ProSavageDDR Driver appears Install Setup Wizard Appears... -
Page 43: Sound Install Alc Audio Codec Driver
4-3 Sound Install ALC Audio Codec Driver 1. Click SOUND when MAGIC INSTALL 2. Then auto detect operation system language MENU appears edition, click OK, start to install DRIVER 3. Click Finish and Restart Windows 4. Click Start→Program→Avance Sound Manager→AvRack. Then AVRACK Windows appears 5. -
Page 44: Lan Install Via10/100Mb Lan Controller Driver
4-4 LAN Install VIA10/100MB LAN Controller Driver The VIA10/100MB PCI Ethernet Adapter Driver path is X:\VIA\LANDRV Click LAN when Magic Install Menu appear 2. Setup VIA 10/100Mb PCI Ethernet Driver Driver install Finish , Click Yes and Restart When windows ask VIA 10/100Mb PCI Computer Ethernet Adapter driver path, Change directory to X:\VIA\LANDRV and click... -
Page 45: Magic Bios Install Bios Live Update Utility
3. Select Finish after setup complete 4. Execute MY GUARD utility, On-time Monitoring your system health 4-6 MAGIC BIOS Install BIOS Live Update Utility Click Magic BIOS when Magic Install Click Next to install the Magic BIOS in MENU appears Destination Folder After finish Setup you will have a Magic Double click the Magic BIOS icon you will... - Page 46 When On-line update BIOS the program Click Next if you need update BIOS, after will auto-check your BIOS version upgrade BIOS, the system will clear CMOS and automatically restart Click Yes if you want to update the BIOS When System programming BIOS don’t turn otherwise choose No to exit off power, after finish update BIOS, the system will clear CMOS and automatically...
-
Page 47: Usb2.0
4-7 USB2.0 Install VIA USB2.0 Device Driver 1. Click USB2.0 when MAGIC INSTALL 2. When USB2.0 Setup Program Appear, Click MENU Appear NEXT 3. Select Install USB Driver and Click NEXT Select FINISH and Restart your Computer 5. Check device working properly in Device Manager The Path of the file is X:\VIA\VIAUSB20\SETUP.EXE... -
Page 48: Pc-Cillin Install Pc-Cillin2004 Anti-Virus Program
4-8 PC-CILLIN Install PC-CILLIN 2004 Anti-virus program 1. Click PC-CILLIN when MAGIC INSTALL 2. Click NEXT when the "Trend Micro internet MENU appear security" installshield wizard windows appear 3. This is license agreement, select "I Accept 4. Click NEXT and Enter your Customer the terms"... -
Page 49: How To Disable On-Board Sound
7. After PC-CILLIN 2004 complete, Please register your information and we recommend select update item to download newest engine code and virus code Note : Please install ACROBAT READER, Before you read PC-CILLIN 2004 User Manual, the path at X:\acrobat\adberdr6_enu_full.exe 4-9 HOW TO DISABLE ON-BOARD SOUND Enter BIOS SETUP choose INTEGRATE PERIPHERALS choose ON-CHIP DEVICE FUNCTION choose AC97 SOUND DEVICE... -
Page 50: Chapter 5 Installation Of Magictwin
CHAPTER 5 5-1 INSTALLATION OF MagicTwin (a 2-User-System solution) Introduction MagicTwin is a 2-User-System solution built on this special designed motherboard with dual video connectors (such as a dual port AGP VGA card), two PS/2 keyboards and two PS/2 mice connected from motherboard using packaged Y-cables and one piece of software (Driver and Tools). - Page 51 As well attach the delivered Y-cables to the “green” port (former PS/2 Mouse port) and into the “violet” port (former PS/2 Keyboard port) at the rear side of the motherboard. Connect the 1 . and 2 . Mouse to the octopus cable, which is also linked to the “green”...
- Page 52 Password and Network Console, click “Next” Type in the Serial and your Address, click “Next” Installation in process, please wait… Afterwards “Reboot your PC”. Windows is restarting and loading the new installed drivers. The MagicTwin will be activated and assign automatically the 2 Station to the 2 monitor, -PS/2-keyboard and PS/2 mouse.
- Page 53 Microsoft License Agreement MagicTwin is (technically) able to run with only a single Windows-XP Installation and license. Each software application including Windows has i's own EULA (End User License Agreement) that you must check for the specifics of multi-user application. 's software license does not supersede any other manufacturer´s license.
Need help?
Do you have a question about the P4MDFTR1A and is the answer not in the manual?
Questions and answers