1. Manuals
  2. Brands
  3. JETWAY Manuals
  4. Motherboard
  5. P4845GEB1A
  6. User manual

JETWAY P4845GEB1A User Manual

M/b for socket 478 pentium 4 processor
Hide thumbs
Table of Contents

Advertisement

Quick Links

P4845GDB/P4845GDBL
P4845GEB/P4845GEBL
P4845PEB/P4845PEBL
USER'S MANUAL
M/B For Socket 478 Pentium 4 Processor
NO. G03-P4845GEB1A
Release date: November 2002
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.

Advertisement

Table of Contents
loading

Related Manuals for JETWAY P4845GEB1A

Summary of Contents for JETWAY P4845GEB1A

  • Page 1 P4845GEB/P4845GEBL P4845PEB/P4845PEBL USER'S MANUAL M/B For Socket 478 Pentium 4 Processor NO. G03-P4845GEB1A Release date: November 2002 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer.

  • Page 2: Table Of Contents

    TABLE OF CONTENT USER’S NOTICE........................... 1 MANUAL REVISION INFORMATION..................1 COOLING SOLUTIONS ......................1 CHAPTER 1 INTRODUCTION OF MOTHERBOARD P4845GDB/P4845GDBL/P4845GEB/P4845GEBL/P4845PEB/P4845PEBL FEATURE OF MOTHERBOARD..................2 SPECIFICATION ......................3 PERFORMANCE LIST ....................4 LAYOUT DIAGRAM & JUMPER SETTING ..............5 CHAPTER 2 HARDWARE INSTALLATION HARDWARE INSTALLATION STEPS................

  • Page 3: User's Notice

    USER’S NOTICE COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER. THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE P4845GDB/P4845GDBL /P4845GEB/P4845GEBL/P4845PEB/P4845PEBL MOTHER-BOARD AND WE DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME WITHOUT NOTICE.

  • Page 4: Chapter 1 Introduction Of

    Chapter 1 Introduction of P4845GDB/P4845GDBL/P4845GEB/P4845GEBL/ P4845PEB/P4845PEBL Motherboard 1-1 Feature of motherboard The P4845GDB/P4845GDBL/P4845GEB/P4845GEBL/P4845PEB/P4845PEBL motherboard is design for use Intel Pentium 4 Processor in 478 Pin Package/Northwood Processor with the Intel 845G/845GE/845PE Chipset delivers a high performance and professional desktop platform solution. Which utilize the Socket 478 design and the memory size expandable to 2.0GB.

  • Page 5: Specification

    1-2 Specification Spec Description ∗ ATX form factor 4 layers PCB size: 30.5x18.0cm Design ∗ Intel 845G (GMCH) Chipset for P4845GDB/P4845GDBL Chipset ∗ Intel 845GE (GMCH) Chipset for P4845GEB/P4845GEBL ∗ Intel 845PE (MCH) Chipset for P4845PEB/P4845PEBL ∗ Intel 82801DB I/O Controller Hub (ICH4) Chipset ∗...

  • Page 6: Performance List

    1-3 Performance List The following performance data list is the testing result of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users (the different Hardware & Software configuration will result in different benchmark testing results.) Performance Test Report Intel Pentium 4 1.9GHz mPGAB package...

  • Page 7: Layout Diagram & Jumper Setting

    1-4 Layout Diagram & Jumper Setting (for P4845GDBL/P4845GEBL/ P4845PEBL) PRINT GAME/MIDI PORT PS/2 Mouse PS/2 Keyboard LINE-IN COM1 VGA/COM2A LINE-OUT (Option) VGA (for P4845GDB/P4845GDBL/ P4845GEB/P4845GEBL/) ATX 12V Power Conn. COM2A (for P4845PEB/P4845PEBL) K/B Power ON CPU Socket Jumper (JP1) PS2 KB/Mouse Port CPU FAN USB Port /LAN Connector...

  • Page 8: Expansion Sockets

    Jumpers Jumper Name Description Page CPU Frequency Select 3-pin Block CMOS RAM Clear 3-pin Block Keyboard Power On Enable/Disabled 3-pin Block Connectors Connector Name Description Page ATXPWR ATX Power Connector 20-pin Block P.13 ATX12V ATX 12V Power Connector 4-pin Block P.13 PS/2 Mouse &...

  • Page 9: Chapter 2 Hardware Installation

    Chapter 2 Hardware installation 2-1 Hardware installation Steps Before using your computer, you had better complete the following steps: 1. Check motherboard jumper setting 2. Install CPU and Fan 3. Install System Memory (DIMM) 4. Install Expansion cards 5. Connect IDE and Floppy cables, Front Panel /Back Panel cable 6.

  • Page 10: Install Cpu

    Note: When should clear CMOS 1. Troubleshooting 2. Forget password 3. After over clocking system boot fail 1-2 closed Normal (Default) 2-3 closed Clear CMOS CMOS RAM Clear Setting (3) Keyboard Power On function Enabled/Disabled: JP1 When setting Enabled you can using keyboard by key in password to power on system. 1-2 closed K/B Power ON Disable 2-3 closed K/B Power ON Enabled...

  • Page 11: About Intel Pentium 4 478-Pin Cpu

    Sound (interface) - the interface between the sound card or integrated sound connectors and speakers, MIC, game controllers, and MIDI sound devices. LAN (interface) - Local Area Network - the interface to your local area network. BIOS (Basic Input/Output System) - the program logic used to boot up a computer and establish the relationship between the various components.

  • Page 12: Install Memory

    2-4 Install Memory This motherboard provides 184-pin DUAL INLINE MEMORY MODULES (DIMM) sites for memory expansion available from minimum memory size of 64MB to maximum memory size of 2.0GB DDR SDRAM. Valid Memory Configurations Bank 184-Pin DIMM Total Memory Bank 0, 1 (DDR1) DDR200/DDR266/DDR333 64MB∼1.0GB DDR SDRAM Module...

  • Page 13: Procedure For Expansion Card Installation

    2-5-1 Procedure For Expansion Card Installation 1. Read the documentation for your expansion card and make any necessary hardware or software setting for your expansion card such as jumpers. 2. Remove your computer’s cover and the bracket plate on the slot you intend to use. 3.

  • Page 14: Agp Slot

    IMPORTANT! If using PCI cards on shared slots, make sure that the drivers support “Shared IRQ” or that the cards don’t need IRQ assignments. Conflicts will arise between the two PCI groups that will make the system unstable or cards inoperable. 2-5-4 AGP Slot This motherboard provides an AGP Slot, only support the 1.5V 4X AGP VGA card.

  • Page 15: Connectors, Headers

    2-6 Connectors, Headers 2-6-1 Connectors Power Connector (20-pin block) : ATXPWR ATX Power Supply connector. This is a new defined 20-pins connector that usually comes with ATX case. The ATX Power Supply allows to use soft power on momentary switch that connect from the front panel switch to 2-pins Power On jumper pole on the motherboard.
  • Page 16 Parallel Port connector is a 25-pin D-Subminiature Receptacle connector. The On-board Parallel Port can be disabled through the BIOS SETUP. Please refer to Chapter 3 “INTEGRATED PERIPHERALS SETUP” section for more detail information. Audio and Game Connector : L _ OUT, L _ IN, MIC, GAME This Connector are 3 phone Jack for LINE-OUT, LINE-IN, MIC and a 15-pin D-Subminiature Receptacle Connector for joystick/MIDI Device.

  • Page 17: Headers

    This connector supports the provided IDE hard disk ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to your hard disk(s). If you install two hard disks, you must configure the second drive to Slave mode by setting its jumpers accordingly.
  • Page 18 Serial Port2 COM2 Header (9-pin) : COM2 (only for P4845GDB/P4845GDBL/P4845GEB/P4845GEBL) Note: Orient the read marking on the C O M2 COM2 ribbon cable to pin 1 Pin 1 Serial Port2 COM2 Header USB Port Headers (9-pin) : USB2, USB3 These headers are used for connecting the additional USB port plug. By attaching an option USB cable, your can be provided with two additional USB plugs affixed to the back panel.
  • Page 19 SPEAK VCC 5 G ND SPKR Pin 1 Pin 1 System Case Connections Wake On-LAN Headers (3-pin) : WOL This connector connects to a LAN card with a WAKE ON-LAN output. This connector power up the system when a wake up signal is received through the LAN card. NOTE: This feature requires that Wake On LAN or Ring In Wake up is enabled.
  • Page 20 (11) IR infrared module Headers (5-pin) : IR This connector supports the optional wireless transmitting and receiving infrared module. You must configure the setting through the BIOS setup to use the IR function. Pin 1 IR infrared module Headers (12) CD Audio-In Headers (4-pin) : CDIN CDIN are the connectors for CD-Audio Input signal.

  • Page 21: Starting Up Your Computer

    2-7 Starting Up Your Computer 1. After all connection are made, close your computer case cover. 2. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V∼240V or 110V∼120V depending on your country’s voltage used.

  • Page 22: Chapter 3 Introducing Bios

    Chapter 3 Introducing BIOS The BIOS is a program located on a Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization.

  • Page 23: The Main Menu

    3-3 The Main Menu Once you enter Award  BIOS CMOS Setup Utility, the Main Menu (Figure 3-1) will appear on the screen. The Main Menu allows you to select from fourteen setup functions and two exit choices. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu.

  • Page 24: Standard Cmos Features

    Load Optimized Defaults Use this menu to load the BIOS default values that are settings for optimal performances system operations. Load Standard Defaults Use this menu to load the BIOS default values that are factory settings for the stable performance system operation. Set Supervisor/User Password Use this menu to set User and Supervisor Passwords.

  • Page 25: Advanced Bios Features

    The time format is <hour><minute><second>. Primary Master/Primary Slave Secondary Master/Secondary Slave Press PgUp/<+> or PgDn/<–> to select Manual, None, Auto type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category.
  • Page 26 Allows you to choose the VIRUS Warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep. Disabled (default) No warning message to appear when anything attempts to access the boot sector or hard disk partition table.

  • Page 27: Advanced Chipset Features

    Keystrokes repeat at a rate determined by the keyboard controller. When enabled, the typematic rate and typematic delay can be selected. The settings are: Enabled/Disabled. Typematic Rate (Chars/Sec) Sets the number of times a second to repeat a keystroke when you hold the key down. The settings are: 6, 8, 10, 12, 15, 20, 24, and 30.

  • Page 28: Dram Timing Settings

    Select Enabled allows caching of the video BIOS, resulting in better system performance. However, if any program writes to this memory area, a system error may result. The settings are: Enabled and Disabled. Memory Hole At 15M-16M You can reserve this area of system memory for ISA adapter ROM. When this area is reserved, it cannot be cached.

  • Page 29: Integrated Peripherals

    CMOS Setup Utility – Copyright(C) 1984-2002 Award Software Integrated Peripherals > Onboard IDE Function Press Enter Item Help > Onboard Device Function Press Enter > Onboard Super IO Function Press Enter Init Display First PCI Slot Menu Level > Power On Function Button Only KB Power On Password Enter...

  • Page 30: Onboard Device Function

    The integrated peripheral controller contains an IDE interface with support for two IDE channels. Select Enabled to activate each channel separately. The settings are: Enabled and Disabled. Primary/Secondary Master/Slave PIO The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of the four IDE devices that the onboard IDE interface supports.

  • Page 31: Onboard Super Io Function

    Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB peripherals. The settings are: Enabled, Disabled. USB Keyboard Legacy Support Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB keyboard.

  • Page 32: Power Management Setup

    To operate the onboard parallel port as Standard Parallel Port only, choose “SPP.” To operate the onboard parallel port in the EPP modes simultaneously, choose “EPP.” By choosing “ECP”, the onboard parallel port will operate in ECP mode only. Choosing “ECP+EPP” will allow the onboard parallel port to support both the ECP and EPP modes simultaneously.

  • Page 33: Pm Timer Reload Events

    Blank Screen This option only writes blanks to the video buffer. V/H SYNC+Blank This selection will cause the system to turn off the vertical and horizontal synchronization ports and write blanks to the video buffer. Modem Use IRQ This determines the IRQ in which the MODEM can use. The settings are: 3, 4, 5, 7, 9, 10, 11, NA.

  • Page 34: Pnp/Pci Configuration Setup

    Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings.

  • Page 35: Irq Resources

    CMOS Setup Utility – Copyright(C) 1984-2002 Award Software IRQ Resources IRQ-3 assigned to PCI Device Item Help IRQ-4 assigned to PCI Device IRQ-5 assigned to PCI Device IRQ-7 assigned to PCI Device Menu Level >> IRQ-9 assigned to PCI Device IRQ-10 assigned to PCI Device...

  • Page 36: Miscellaneous Control

    3-11 Miscellaneous Control This section is for setting CPU Frequency/Voltage Control. CMOS Setup Utility – Copyright(C) 1984-2002 Award Software Miscellaneous Control CPU Clock Ratio Item Help Auto Detect PCI Clk Enabled Spread Spectrum Disabled ** Current Host Clock is 100/33MHz ** Menu Level >...

  • Page 37: Load Standard/Optimized Defaults

    Load Standard Defaults When you press <Enter> on this item, you get confirmation dialog box with a message similar Load Standard Defaults (Y/N)? N Pressing <Y> loads the BIOS default values for the most stable, minimal-performance system operations. Load Optimized Defaults When you press <Enter>...

  • Page 38: Magic Install Supports Windows 95/98/98Se/Nt4.0/2000/Xp

    Check your package and there is A MAGIC INSTALL CD included. This CD consists of all DRIVERS you need and some free application programs and utility programs. In addition, this CD also include an auto detect software which can tell you which hardware is installed, and which DRIVERS needed so that your system can function properly.

  • Page 39: Inf Install Intel 845 Chipset System Driver

    1. Click INF in the MAGIC INSTALL MENU 2. Click NEXT when Chipset Software Install Utility appears 3. This chart shows motherboards supported by 4. Select if you want computer re-started click the driver click Yes Finish NOTE: MAGIC INSTALL will auto detect file path X:\INTEL845\INF\SETUP.EXE This driver supports WINDOWS 98SE/ME/2000/XP (NT4.0 do not require) 4-2 VGA...

  • Page 40: Sound Install Alc Audio Codec Driver

    Click YES, This is Announce CopyRight 4. If You Want Re-start Computer , Click FINISH 4-3 Sound Install ALC Audio Codec Driver 1. Click SOUND when MAGIC INSTALL 2. Then auto detect operation system language MENU appears edition, click OK, start to install DRIVER 3.

  • Page 41: Lan Install Via Vt6105 Pci 10/100Mb Fast Ethernet Driver

    5. Sound Effect select and KaraOK Mode 6. Manual Sound Effect Setting Function Note: The path of the file For WIN98/NT4.0/WIN2K/XP is X:\CODEC\ALCCODEC\SETUP.EXE 4-4 LAN Install VIA VT6105 PCI 10/100MB Fast Ethernet Driver WINDOWS 98SE/98ME/2000/XP Setup 1. Click LAN when Magic Install Menu appear 2.

  • Page 42: Pc-Health Intel 845 Pc-Health Monitor

    4-5 PC-HEALTH Intel 845 PC-Health Monitor The path of the file is X:\INTEL845\HW30\SETUP.EXE (Only support WINDOWS 98SE/ME) In Windows 98 Winbond Hardware Doctor Monitoring Software needs some system files to copy in Utility that’s why it needs install PC-HEALTH twice to complete setup. 1.

  • Page 43: Mbios&Dx8 Install Bios Live Update Utility And Directx8.1

    3. This is a CPU/System Fan Speed and 4. This is a CPU and System Memory status Temperature status information information 4-6 MBIOS&DX8 Install BIOS Live Update Utility and DIRECTX8.1 1. Click Magic BIOS when Magic Install 2. Click Next to install the Magic BIOS in MENU appears Destination Folder 3.

  • Page 44: Iaa Install Intel Application Accelerator Software

    and automatically restart Click Yes if you want to update the BIOS When System programming BIOS don’t turn otherwise choose No to exit off power, after finish update BIOS, the system will clear CMOS and automatically Restart When choose From Local Driver to update 10.

  • Page 45: Pc-Cillin Install Pc-Cillin2002 Anti-Virus Program

    4-8 PC-CILLIN Install PC-CILLIN 2002 Anti-virus program 1. Click PC-CILLIN when MAGIC INSTALL 2. (1) Click "Install PC-CILLIN" when PC- MENU appear CILLIN 2002 main menu appears, and Click NEXT when "Install Shield Wizard For PC- CILLIN 2002" (2) Click Open Manual. you can learn PC- CILLIN 2002 how to use 3.

  • Page 46: How To Install Usb 2.0 Driver

    7. After PC-CILLIN 2002 complete, Please 8. finish register process, we recommend select register your information and get LICENSE update item to download newest engine code KEY from TREND MICRO web site, enter and virus code your license key and click FINISH Note : Please install ACROBAT READER, Before you read PC-CILLIN 2002 User Manual, the path at X:\acrobat\ar500eng.exe...

  • Page 47: How To Disable On-Board Sound

    4-10 HOW TO DISABLE ON-BOARD SOUND Enter BIOS SETUP choose INTEGRATE PERIPHERALS choose ON-CHIP DEVICE FUNCTION choose AC97 SOUND DEVICE Disable on-board sound function by press PAGE DOWN KEY to Disable 4-11 HOW TO UPDATE BIOS Before update BIOS users have to “Disable”, “Flash Part Write Protect” item which in “Miscellaneous Control”...

This manual is also suitable for:

P4845gdbP4845gdblP4845gebP4845geblP4845pebP4845pebl

Table of Contents