Page 1
HF4142 MULTI - POSITION WORKOUT BENCH Note: Both Serial Number and Model Number are Required when Ordering Parts Note: Both Serial Number and Model Number are Required when Ordering Parts Note: Both Serial Number and Model Number are Required when Ordering Parts...
Page 3
Using this product in a commercial setting will void all warranties and can result in serious injury or death!! TOOLS REQUIRED Socket Wrench 1/2" and 9/16" Sockets Crescent Wrench Rubber Mallet Tape Measure Level Allen Wrench Set PAGE 02 HF4142 ASSEMBLY...
Page 7
NOTE: - WRENCH TIGHTEN SCREW (13) THEN LOOSEN NUT ENOUGH FOR (2) TO PIVOT FREELY. - WRENCH TIGHTEN SCREW'S (22) THEN LOOSEN NUT ENOUGH FOR (21) TO SPIN FREELY. - ASSEMBLE LEFT WHEEL SAME AS RIGHT. PAGE 06 HF4142 ASSEMBLY...
Page 8
026-01X2003 BACK PAD ADJUSTER 026-01X1592 PULL PIN ASSEMBLY 026-01P1590 BACK PAD MOUNT 013-0903004 3/8" PLASTIC WASHER 011-0101079 3/8"-16UNC X 6.00" BHCS (WZ) 013-0102027 CUSTOM WASHER OD .631", ID .406" (WZ) 012-0104008 3/8"-16UNC THIN NYLOCK NUT (WZ) HF4142 ASSEMBLY PAGE 07...
Page 9
OWNERS OWNERS OWNERS OWNERS MANUAL MANUAL MANUAL MANUAL NOTE: - WRENCH TIGHTEN SCREWS (14) THEN LOOSEN NUT ENOUGH FOR (3), (4), AND (8) TO PIVOT FREELY. PAGE 08 HF4142 ASSEMBLY...
Page 16
MANUAL MANUAL MANUAL MANUAL FRAME ASSEMBLY STEP 6 ITEM NO. PART NUMBER DESCRIPTION 026-01X2000 REAR FRAME ASSEMBLY 026-01X2001 FRONT FRAME ASSEMBLY 016-0201022 END CAP 2.00" (BLACK) 019-0002002 CLOSED END GRIP 2.00" 019-0002046 CLOSED END GRIP 2.00" HF4142 ASSEMBLY PAGE 15...
Page 18
CENTERED ON TUBE SERIAL # DECAL CENTERED ON 021-0003114 TUBE CENTERED ON TUBE 021-0003222 .875 CENTERED ON PLATE 1.50 1.75 021-0003114 CENTERED ON 021-0003227 TUBE CENTERED ON TUBE 019-0001007 CENTERED 12.50" BACK FROM FRONT OF BENCH PAGE 17 HF4142 ASSEMBLY...
Page 19
DECAL REFERENCE THIS PRODUCT IS NOT DESIGNED FOR COMMERCIAL USE. 021-0003222 USING THIS PRODUCT IN A COMMERCIAL SETTING CAN RESULT IN SERIOUS INJURY OR DEATH! 021-0003223 SERIAL # DECAL 500 LBS. MAXIMUM WEIGHT RATING 021-0003114 021-0003227 021-0003221 HF4142 ASSEMBLY PAGE 18...
Page 20
CUSTOM WASHER OD .631", ID .406" (WZ) 013-0302008 5/16" USS FLAT WASHER (WZ) 013-0102022 3/8" INTERNAL LOCK WASHER 012-0104008 3/8"-16UNC THIN NYLOCK NUT (WZ) 020-0014031 WHEEL 2 3/16" 011-0101042 3/8"-16UNC X 1.75" BHCS (WZ) 019-0002046 CLOSED END GRIP 2.00" HF4142 ASSEMBLY PAGE 19...
Page 23
Hoist Fitness Systems sole responsibility shall be to repair or replace the component within the terms stated above. Hoist Fitness Systems shall not be liable for any loss or damage of any kind including any incidental or consequential damages resulting, directly or indirectly from any warranty expressed or implied or any other failure of this product.
Need help?
Do you have a question about the HF4142 and is the answer not in the manual?
Questions and answers