Ryobi RA-NBS1832-S2 Operator's Manual
  1. Manuals
  2. Brands
  3. Ryobi Manuals
  4. Nail Gun
  5. RA-NBS1832-S2
  6. Operator's manual
Ryobi RA-NBS1832-S2 Operator's Manual

Ryobi RA-NBS1832-S2 Operator's Manual

Airwave air brad nailer/stapler (2 in 1)
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
RA-NBS1832-S2
AIRWAVE AIR BRAD NAILER/STAPLER (2 IN 1)
OPERATOR'S MANUAL
ORIGINAL INSTRUCTIONS
Important!
It is essential you read the instructions in this manual before starting and
operating this machine.
Subject to technical modifications.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RA-NBS1832-S2 and is the answer not in the manual?

Questions and answers

Related Manuals for Ryobi RA-NBS1832-S2

Summary of Contents for Ryobi RA-NBS1832-S2

  • Page 1 RA-NBS1832-S2 AIRWAVE AIR BRAD NAILER/STAPLER (2 IN 1) OPERATOR'S MANUAL ORIGINAL INSTRUCTIONS Important! It is essential you read the instructions in this manual before starting and operating this machine. Subject to technical modifications.
  • Page 2 DESCRIPTION 1. NITTO style coupler 2. No mar pad 3. Safety yoke 4. Exhaust cap 5. Air supply 6. Magazine 7. Nails 8. Staples 9. Trigger 10. Depth adjustment knob 11. Flat blade screwdriver 12. Jam release Fig. 1 Fig. 2 Fig.
  • Page 3 Fig. 7 Fig. 8 Fig. 9 7, 8 Fig. 10 Fig. 11...
  • Page 4 Quick Quick connector connector Lubricator Filter Tool compressor Cut-off valve Quick Quick coupler coupler Regulator Air hose (0-8.5 bar) Fig. 12...

  • Page 5: General Safety Rules

    shields during operation of the tool. GENERAL SAFETY RULES ■ The risks to others shall be assessed by the operator. ■ Keep fingers away from trigger when not operating this ■ Be careful with tools without workpiece contact as they tool and when moving from one operating position to can be fired unintentionally and injure operator and/ another.

  • Page 6: Noise Hazards

    INFORMATION ON MECHANICAL IMPACT(VIBRATION) ■ This tool is not intended for use in potentially explosive atmospheres and is not insulated from coming into The characteristic vibration values for the fastener driving contact with electric power. tool have been determined in accordance with ISO 8662- ■...
  • Page 7 ■ Using oxygen or combustible gases for operating – applying excessive force of any kind. pneumatic tools creates a fire and explosion hazard. ■ Never point any fastener driving tool at yourself or at any other person or animal. ■ Be careful when using pneumatic tools as the tool could become cold, affecting grip and control.

  • Page 8: Residual Risks

    have an internal diameter of at least 19 mm and a corresponding large diameter where relatively long Tacker with safety yoke pipelines or multiple users are involved. ■ Compressed air pipelines should be laid so as to form a gradient (highest point in the direction to the compressor).

  • Page 9: Intended Use

    ah,W=3.240 m/s 2 , ASSEMBLY Vibration in the K=0.058 m/s 2 handle UNPACKING REPLACEMENT PARTS This product has been shipped completely assembled. No mar pad 079003012060 ■ Carefully remove the tool and any accessories from the box. Make sure that all items listed in the packing Air tool oil 079003009803 list are included.

  • Page 10: Adjusting The Exhaust

    the safety yoke. To replace the pad, fit it into place over WARNING the safety yoke and push up at the back to reseat. Do not allow familiarity with tools to make you careless. ADJUSTING THE EXHAUST Remember that a careless fraction of a second is sufficient to inflict severe injury.
  • Page 11 4. Close the magazine. WARNING Always use a coupling that discharges all the WARNING compressed air in the tool at the time the fitting or Use only the fasteners recommended for use with this hose coupling is disconnected. Using a coupling that tool.

  • Page 12: Clearing A Jammed Fastener

    Single sequential actuation mode pressure adjustments alone. If finer adjustments are needed, use the drive depth adjustment on the tool. The tool employs single sequential actuation mode. 1. Connect the tool to the air supply. DRIVE DEPTH ADJUSTMENT 2. Grip the tool firmly to maintain control. Position the See figure 9.

  • Page 13: Cold Weather Operation

    COLD WEATHER OPERATION 5. Close the jam release and latch. 6. Reconnect the tool to the air supply. For cold weather operation, near and below freezing, 7. Reinstall fasteners. the moisture in the air line may freeze and prevent tool operation.
  • Page 14 7. Set the depth of drive according to the “drive depth adjustment” section in this manual. Repeat this checklist before using the tool each day, or if the tool is dropped or damaged in any way. WARNING Do not use any attachments or accessories not recommended by the manufacturer of this tool.

  • Page 15: Parts List

    PARTS LIST No. Description Description Description No. Description Deflector bolt Gun body Roll pin 2.5 x 18 Bolt M4 x 12 Deflector spring Rubber washer Magazine Orientation seat Air deflector Bolt M3 x 8 Fixed cover Orientation handle spring Orientation spring Guide sleeve Spring washer Roll pin 3 x 20...

  • Page 16: Troubleshooting

    31 Gilby Road, Mount Waverley, VIC, 3149, Australia Techtronic Industries N.Z. Limited RYOBI is a trade mark of Ryobi Limited, and is used under license. Unit C, 70 Business Parade South, NITTO is a registered trade mark owned by Nitto Kohki Co., Ltd.

Table of Contents