Related Manuals for Ryobi RA-NBS1664-S
Summary of Contents for Ryobi RA-NBS1664-S
- Page 1 RA-NBS1664-S AIRWAVE AIR BRAD NAILER/STAPLER (3 IN 1) OPERATOR'S MANUAL ORIGINAL INSTRUCTIONS Important! It is essential you read the instructions in this manual before starting and operating this machine.
- Page 2 DESCRIPTION 1. Nitto style coupler 12. Jam release 2. No mar pad 13. Flat blade screwdriver 3. Safety yoke 4. Exhaust cap 5. Air supply 6. Magazine 7. 18 gauge nails 8. 16 gauge nails 9. Crown staples 10. Trigger 11.
- Page 3 Fig. 7 Fig. 8 Fig. 9 Fig. 10 7, 8, 9 Fig. 11...
- Page 4 Fig. 12 Quick Quick connector connector Lubricator Filter Tool compressor Cut-off valve Quick Quick coupler coupler Regulator Air hose (0-8.5 bar) Fig. 13...
-
Page 5: General Safety Rules
comfortable posture while maintaining a secure footing GENERAL SAFETY RULES and avoiding awkward or off-balanced postures. The operator should change posture during extended For multiple hazards, read and understand the safety instructions before installing, operating, repairing, tasks, which can help avoid discomfort and fatigue. maintaining, changing accessories on, or working If the operator experiences symptoms, such as near, the air tool. -
Page 6: Information On Mechanical Impact(Vibration)
INFORMATION ON MECHANICAL IMPACT(VIBRATION) Repairs shall be carried out only by the manufacturer's authorized agents or by other experts, having due The characteristic vibration values for the fastener driving regard to the information given in the operating tool have been determined in accordance with ISO 8662- instructions. -
Page 7: Specifications
trigger using finger pressure. In addition, fastener driving tool is fitted with a safety yoke which enables the driving operation to be carried SYMBOLS out only after the safety yoke of the tool is pressed against a work piece, These tools are marked with an inverted triangle behind the serial number and are Safety alert... -
Page 8: Noise And Vibration
Upholstery 6000 series narrow Picture framing crown staples – 1.25 Staple type AIR SUPPLY AND OPERATION Staple range: 16 - 40 mm before connecting to the air supply. Collation angle: 0° Required air pressure range of 4.8 - 8.3 bar (70 - 120 TOOL Magazine capacity 100 nails... -
Page 9: Operation
WARNING WARNING If any parts are damaged or missing do not operate Please read and observe these operating instructions this tool until the parts are replaced. Use of this product before using the tool. Basic safety measures should with damaged or missing parts could result in serious always be strictly followed to protect against damage to personal injury. - Page 10 WARNING WARNING Empty the magazine to prevent a fastener from being ejected at the next stage of work in the event that internal parts of the fastener driving tool are not in the tool so that the safety yoke is not pointing towards the starting position following maintenance and repair work operator or any other person or animals.
-
Page 11: Setting The Air Pressure
WARNING WARNING Do not use fasteners with shank diameter/width smaller During normal use the tool will recoil immediately after driving a fastener. This is a normal function of fasteners to exit the tool prematurely through the guide the tool. Do not attempt to prevent the recoil by holding track. -
Page 12: General Maintenance
2. Turn the depth adjustment knob left or right to change WARNING the driving depth. Always wear eye protection with side shields marked to 3. Reconnect the tool to the air supply. comply with one of the following standards: 4. Drive a test fastener after each adjustment until the desired depth is set. - Page 13 problems for these symptoms, trace the air supply from If it becomes necessary to store the product for an extended the tool to the supply source for restrictive connectors, low points containing water and anything else that would a generous amount of lubrication at that time. Actuate the tool 10 - 15 times without fasteners loaded to ensure oil has been evenly distributed throughout the product.
-
Page 14: Troubleshooting
TROUBLESHOOTING PROBLEM CAUSE POSSIBLE SOLUTION Loose screws. Tighten screws. Air leak near the top of the tool or in the trigger area. Worn or damaged O-rings or seals. Install overhaul kit. Loose screws. Tighten screws. Air leak near the bottom of the tool. -
Page 15: Parts List
PARTS LIST No. Description Description Description No. Description Bolt M5 x 16 Pin 3 x 26 O-ring 15 x 2.65 Fixed lever Axle sleeve Orientation seat Trigger seat Bolt M4 x 20 Adjustment washer Spring Fixed magazine Bolt Compressed spring Pin sleeve Nail guide strip Spring washer... - Page 16 Techtronic Industries (Australia) Pty. Ltd. Level 1, 660 Doncaster Road Doncaster, VIC 3108, Australia Techtronic Industries New Zealand Ltd. 18-26 Amelia Earhart Avenue Mangere, Auckland 2022, New Zealand...
Need help?
Do you have a question about the RA-NBS1664-S and is the answer not in the manual?
Questions and answers