Related Manuals for Fisher & Paykel HP60IDCHEX4
Summary of Contents for Fisher & Paykel HP60IDCHEX4
- Page 1 INTEGRATED INSERT RANGEHOOD WITH EXTERNAL MOTOR CONTEMPORARY HP60IDCHEX4 & HP90IDCHEX4 INSTALLATION GUIDE NZ AU...
- Page 2 SAFETY AND WARNINGS Always switch the power off prior to installation, servicing or cleaning of the appliance. WARNING! This appliance must be installed and connected to the mains power supply only by a suitably qualified person according to these installation instructions and in compliance Electric Shock Hazard with any applicable local building and electricity regulations.
- Page 3 COMPONENTS REQUIRED PARTS TOOLS Keep all packing materials until the unit has been inspected. Not supplied Inspect the product to ensure there is no shipping damage. If any damage is detected contact the dealer or retailer you bought the product from to report the damage. Fisher &...
- Page 4 PRODUCT DIMENSIONS Model nos: HP60IDCHEX4 Product Dimensions a Overall height of rangehood without ducting adapter B Overall height of rangehood with ducting adapter c Overall width of rangehood d Overall depth of rangehood (excl. cabinetry front panel) e Diameter of ducting adaptor...
- Page 5 PRODUCT DIMENSIONS Model nos: HP90IDCHEX4 Product Dimensions a Overall height of rangehood without ducting adapter B Overall height of rangehood with ducting adapter c Overall width of rangehood d Overall depth of rangehood (excl. cabinetry front panel) e Diameter of ducting adaptor f Width of of rangehood chassis h Depth of rangehood chassis NOT TO SCALE...
- Page 6 CUTOUT DIMENSIONS 60cm model 90cm model HP60 HP90 CUTOUT DIMENSIONS CUTOUT DIMENSIONS A Overall width of the cutout A Overall width of the cutout B Overall depth of the cutout B Overall depth of the cutout...
- Page 7 INSTALLATION HEIGHT Induction cooktop considerations Induction cooktops use energy efficient technology that only heats the contents of a cooking pot. Unlike gas or traditional electric cooktops, the surrounding air does not get heated when using an induction cooktop. As a result, rangehood filters, splashbacks and surrounding cabinetry do not get warmed up, increasing the likelihood of condensation on these cooler surfaces.
- Page 8 This rangehood is designed to operate with a Fisher & Paykel external blower with the exhaust air ducted externally from the kitchen. External blower rangehood installation is different from internal blower rangehood MODEL FREQUENCY VOLTAGE installation. HP60IDCHEX4 50 Hz 164 W HP90IDCHEX4 50 Hz 164 W For optimum performace of this blower: 1 Identify roof location where blower noise will be acceptable.
- Page 9 INSTALL PREPARATION / CONSIDERATIONS The rangehood must be installed offset from the remote motor to achieve the expected noise performance. The external motor should be 4-6m away from hood. Refer to cooktop specifications to ensure adequate clearances are maintained. Duct to roof. One power outlet is required, this must be accessible to the customer.
- Page 10 CHECK DUCTING UNPACK PRODUCT Ensure the ducting is the correct length and compatible to the rangehood. Ensure both external motor and If ducting is supplied with the external rangehood cartons are present. motor check that it is the correct length. If needed additional ducting of the same diameter can be used.
- Page 11 PREPARE MOTOR INSTALL EXTERNAL MOTOR Before cutting into roof, locate studs and make hole beside the studs for securing later. Rest upside down and fit the backdraft damper using four Phillips screws. Create hole in roof for PVC pipe. Orient PVC pipe with pre-drilled holes at the top, insert into the hole.
- Page 12 INSTALL EXTERNAL MOTOR INSTALL DUCTING 200MM FLEXI DUCTING Secure motor to the PVC pipe using four Phillips screws. Check length. Seal around the power cord slot as required. Connect ducting to motor and secure using supplied clamp. Route power cord through PVC pipe and the lower slot.
- Page 13 PREPARE CABINETRY PREPARE HOOD Ensure the cabinetry can support the weight of the rangehood and ducting. NON PRECUT CABINETRY Fit the duct adapter to the rangehood using four supplied Phillips screws. Centre rangehood over cooktop and prepare cutout to the required specifications.
- Page 14 INSTALL HOOD Lift rangehood into cavity until brackets Refit perimeter plate and secure using rest on the cabinetry. Ensure power cord the screws removed in step 3. remains free and unobstructed. Ensure filters are oriented correctly Unclip filters to remove. before clipping back into place.
- Page 15 SECURE DUCTING CONNECT POWER Attach flexible ducting to rangehood duct adapter. Plug in and turn power on. Secure using tape, cable ties or metal straps as required. Connect the external motor plug to the rangehood socket.
- Page 16 AFTER POWER CONNECTION INSTALLER CHECKLIST TO BE COMPLETED BY THE INSTALLER … Have all packaging been removed? Remove film from all surfaces of the … rangehood. Rangehood is correctly installed … All connections are secure … The ducting is not crushed or blocked in any areas …...
- Page 17 FISHERPAYKEL.COM © Fisher & Paykel Appliances 2024. All rights reserved. The models shown in this guide may not be available in all markets and are subject to change at any time. The product specifications in this guide apply to the specific products and models described at the date of issue.
Need help?
Do you have a question about the HP60IDCHEX4 and is the answer not in the manual?
Questions and answers