ABSCO SHEDS 60303WK Instruction Manual
Large gable shed n3/c1 frame kit
Hide thumbs
Also See for 60303WK:
- Assembly instructions manual (39 pages) ,
- Assembly instructions manual (44 pages) ,
- Manual (40 pages)
Advertisement
Quick Links
AU: 1800 029 701
NZ: 0800 466 444
This instruction manual is to be used during
the initial construction of the structure.
This kit is applicable to the following sheds:
60303WK
3060UTK
52233WK
3052UTK
45302WK
3045UTK
45232WK
The addition of this frame kit will increase the
wind rating of the specified sheds to
Wind rating: N3/C1 as per AS4055-2021.
Suitable for specific cyclonic regions
DOWNLOAD
OUR APP FOR
ASSEMBLY
VIDEOS
Absco Industries
Assembly Instruction Manual
LARGE GABLE SHED
N3/C1 FRAME KIT
FOR WORKSHOP & UTILITY MODELS
admin@absco.com.au
www.abscosheds.com.au
Where information conflicts with the original
instruction manual, this document is to be
referenced.
View of frame kit applied to
WARNING: This shed must be anchored to a
100mm thick concrete slab with the concrete
anchors supplied.
Failure to do so will result in the shed not
having the structural integrity required to
endure a severe storms or cyclonic event.
WARNING: Doors must remain closed with
all padbolts properly secured during severe
storms or cyclonic event.
PLEASE LEAVE A REVIEW
Tell us about your experience!
Visit www.abscosheds.com.au/review
Model: CYCWKUTK
60303WK
2/12/24
1.3
1
Advertisement
Related Manuals for ABSCO SHEDS 60303WK
Summary of Contents for ABSCO SHEDS 60303WK
- Page 1 This instruction manual is to be used during instruction manual, this document is to be the initial construction of the structure. referenced. View of frame kit applied to 60303WK This kit is applicable to the following sheds: 60303WK 3060UTK WARNING: This shed must be anchored to a...
-
Page 2: General Instructions
LARGE GABLE SHED N3/C1 FRAME KIT FOR WORKSHOP & UTILITY MODELS GENERAL INSTRUCTIONS • Before commencing any assembly, read through these instructions in detail to gain a thorough understanding of assembly methods and associated details. • Unpack the carton and carefully identify and check off all the parts against the parts described and illustrated on "COMPONENTS PACKING LIST"... - Page 3 LARGE GABLE SHED N3/C1 FRAME KIT FOR WORKSHOP & UTILITY MODELS COMPONENT PACKING LIST FRAME PACK COMPONENT PART COMPONENT PART CHK QTY DESCRIPTION DESCRIPTION GABLE VERTICAL C2750 C1555 WALL BRACE DOOR BRACE NON-GABLE HORIZONTAL C2100 K0640 WALL AND ROOF DOOR BRACE BRACE PORTAL UTILITY...
-
Page 4: Fittings And Accessories
LARGE GABLE SHED N3/C1 FRAME KIT FOR WORKSHOP & UTILITY MODELS COMPONENT PACKING LIST FITTINGS AND ACCESSORIES COMPONENT PART COMPONENT PART CHK QTY DESCRIPTION DESCRIPTION 8G x 3/8” SELF INSTRUCTION FAST001 TAPPING SCREW MANUAL (220 PACK) 10G x 5/8” WAFER 3/16”... - Page 5 ZARSP supplied in the this kit. • For ease of assembly ALL portal frames shall be erected during the initial construction of the structure. 4 portal frame layout: 60303WK 52233WK - Not to scale NOTE: Two portal frames are supplied in original kit.
- Page 6 LARGE GABLE SHED N3/C1 FRAME KIT FOR WORKSHOP & UTILITY MODELS UTILITY SHEDS - FRAMING OVERVIEW • Positions of portal frames may differ from the original instruction manual. Where necessary join ridge beams using additional ZARSP supplied in the this kit. •...
- Page 7 LARGE GABLE SHED N3/C1 FRAME KIT FOR WORKSHOP & UTILITY MODELS USING SELF DRILLING TEK SCREWS Self drilling tek screws are an effective means of securing components without the need to pre-drill holes. By following these instructions you will be able to easily secure your frame kit components. Self drilling tek screws require an electric or battery drill for installation, Do not attempt to fasten tek screws by hand.
- Page 8 LARGE GABLE SHED N3/C1 FRAME KIT FOR WORKSHOP & UTILITY MODELS BOXING FRAME SECTIONS 1. All frame sections have one side length of 2. Slide the 38mm side into the 40mm side 38mm and another at 40mm. as shown. 3. Slide opposing sides together so that 4.
- Page 9 LARGE GABLE SHED N3/C1 FRAME KIT FOR WORKSHOP & UTILITY MODELS Applies to UTILITY SHEDS only FRONT FRAME ASSEMBLY (N3/C1) STEP 1 of 2 Box the following frame sections Refer to “BOXING together and fi x with tek screws. FRAME SECTIONS” for further details •...
- Page 10 LARGE GABLE SHED N3/C1 FRAME KIT FOR WORKSHOP & UTILITY MODELS FRONT FRAME ASSEMBLY (N3/C1) STEP 2 of 2. Fit one C0100 to box the base of each outside leg as shown. These will later be used for securing the Secure the small triangular frame to the concrete plate (ZACO190) to the...
-
Page 11: Anchoring Methods
LARGE GABLE SHED N3/C1 FRAME KIT FOR WORKSHOP & UTILITY MODELS ANCHORING METHODS Bolt and Nut* Fixing M10 dynabolt requires drilling into the M10 4.6/S concrete slab using a masonry bit. Holes must have a minimum slab edge distance of 60mm. Wall Sheet Steel Angle* 35 x 35 x 3... - Page 12 LARGE GABLE SHED N3/C1 FRAME KIT FOR WORKSHOP & UTILITY MODELS ANCHORING LAYOUT Slab dimensions below illustrate the minimum required anchors per wall. Ensure that anchors are evenly spaced along wall. 6060mm for 6.0m wall 5323mm for 5.2m wall 4580mm for 4.5m wall Absco Industries Assembly Instruction Manual Model: CYCWKUTK...
- Page 13 INSTALL EXTRA FASTENERS Absco sheds sheets have punched holes typically spaced at 592mm from centre to centre. To achieve a cyclonic wind rating additional screws will need to be installed to reduce these distances.
- Page 14 LARGE GABLE SHED N3/C1 FRAME KIT FOR WORKSHOP & UTILITY MODELS INSTALL EXTRA FASTENERS - INTERIOR VIEW “C” - Roof panel to ridge beam. Pre-drill from inside the shed upward through the ridge beam and into the roof panel at 148mm centres, (every pan) then fix with a screw.
- Page 15 LARGE GABLE SHED N3/C1 FRAME KIT FOR WORKSHOP & UTILITY MODELS DOOR BRACING NOTE: If the door has been completely assembled as per original instruction manual you will need to remove the diagonal door braces. 1. Seal any brace holes using the supplied pop rivets, FAST007.
- Page 16 LARGE GABLE SHED N3/C1 FRAME KIT FOR WORKSHOP & UTILITY MODELS DOOR BRACING 5. Place the door frame against the door, ensure 6. Use tek screws to fi x the frame to the door that it is centred. If the door is already fi tted to the at every corner.
- Page 17 LARGE GABLE SHED N3/C1 FRAME KIT FOR WORKSHOP & UTILITY MODELS BRACING FOR NON-GABLE WALLS NOTE: This wall bracing will have to cut to suit from part C2100. 1. Take the cut-to-length framing for the non- gable wall, and partially box them together, do not tek screw yet.
- Page 18 LARGE GABLE SHED N3/C1 FRAME KIT FOR WORKSHOP & UTILITY MODELS BRACING FOR NON-GABLE WALLS - PORTAL FRAME For the open side of the portal frame take a piece of offcut, approx 150mm long, and box as shown. NOTE: This method will be used later to mount the roof bracing. Now fasten all boxed frame sections to the non-gable wall from the outside of the shed.
- Page 19 LARGE GABLE SHED N3/C1 FRAME KIT FOR WORKSHOP & UTILITY MODELS BRACING FOR NON-GABLE WALLS - DOOR STUDS In instances where a portal frame is not positioned on both sides of the door opening, as per the framing layout, a door stud is required. Two C1704 are to be used as follows.
- Page 20 LARGE GABLE SHED N3/C1 FRAME KIT FOR WORKSHOP & UTILITY MODELS BRACING FOR GABLE WALLS Construction for the gable walls is similar to the non-gable wall. 1. Take two C2750 frame pieces for the gable wall, and partially box them together, do not tek screw yet.
- Page 21 LARGE GABLE SHED N3/C1 FRAME KIT FOR WORKSHOP & UTILITY MODELS ROOF BRACING NOTE: This roof bracing will have to cut to suit 2. Using a marker trace along one edge of the from part C2100. channel onto the roof sheet as shown. Next measure 20mm in from this line and mark 1.
- Page 22 Absco Sheds Storage Guidelines • Absco Sheds are designed to be weatherproof for normal weather conditions. In the event of extreme weather conditions such as heavy rain, combined with high wind gusts, the ridge capping, sheeting joins, screw fi xings etc., may exhibit minor deformations which may allow some water entry. These areas should be checked regularly to ensure that maximum strength and protection is maintained.
- Page 23 Lifetime Warranty Statement 1. DEFINITIONS 3. WARRANTY CLAIM PROCEDURE In this document, capitalised terms have the following meaning: 3.1. If, during the Lifetime Warranty Period, You believe the Product has a “ABSCO” means John Scholtes Investments (No. 1) Pty Ltd trading Defect, You must comply with the procedure set out in this clause 3.
- Page 24 4. WARRANTY LIMITATIONS / EXCLUSIONS 4.1. To the extent permitted by law, this warranty will not apply where: the Product has been installed or used for a purpose that is not an Authorised Purpose; the Product has not been installed, assembled, maintained and/or special, indirect or consequential loss or damage of any nature operated in complete compliance with ABSCO’s Product Guide;...
Need help?
Do you have a question about the 60303WK and is the answer not in the manual?
Questions and answers