Sharp AY-ZP25TR Installation Manual

SPLIT AIR / AIR HEAT PUMP
INSTALLATION MANUAL
• Installation must be made in accordance with the installation manual by
.
• After installation has complete, check that there is no leakage of refriger-
ant gas.
• Ventilate the room if refrigerant gas leaks during installation.
Make in place and that the terminals are free of any excess
force from the
• Form the cable so that the control box cover, the cord holder and cable
holder are not loose.
ITEMS Q'ty
1 MOUNTING PLATE To mount the indoor unit on
the wall.
1
2 WALL PLUG
the long screws(7).
9
the special screw(2).
3 LONG SCREW
(M4.5x30)
7
4 REMOTE CONTROL To control remotely.
1
NOTES ON LOCATIONS
Indoor unit
in the entire room.
2.
3. both sides and above the unit.
5.
remote control.
6. Keep the air inlet clear of obstacles that could block incoming air.
7.
8.
brations.
INSTALLATION DIAGRAM
MIN.50
MIN.100
MIN.200
APPLICATION ITEMS
5 DRY BATTERY
6 SPECIAL SCREW
(Black)
7 Remote control
holder
8 SHORT SCREW
(M4x20)
unit and the
lighting.
and extreme vi-
MIN.60(Recommended more than 100mm)
MIN.50
MIN.70
Provide as much installation
air-conditioning.
MIN.200
INDOOR UNIT
AY-ZP25TR
AY-ZP35TR
cause refrigerant gas leakage.
• When installing the unit, take care not to enter air substance other than the
Otherwise, it will cause burst and injury as a result of abnormal high pressure in the refrig-
erant cycle.
• Be sure to connect the refrigerant pipe before running the compressor.
Otherwise, it will cause burst and injury as a result of abnormal high pressure in the refrig-
erant cycle.
• Earth the unit.
Incomplete earth may cause electrical shock.
• If national legislations or type of installation requires earth leakage breaker,
the legislation must be followed
• Arrange the drain hose to ensure smooth drainage.
•
Use the
Q'ty APPLICATION
For the remote control.
AAA batteries.
2
• To mount the remote con-
trol on the wall.
2
• To mount the remote con-
trol holder on the wall.
To mount the remote control
on the wall.
1
1
Outdoor unit
1. Place the outdoor unit on a stable base.
2.
3.
4. Water drain from the unit should be let out without problem.
5.
6. Avoid locations exposed to machine oil vapor, salty air (facing the seashore,
7.
tampered with.
8.
9. Keep the air outlet opening free of any obstacle. This could affect the performance of the unit
and create loud noises.
PIPING
Indoor
Unit
MIN.50
Max.
piping
length:
A
15m
• Standard piping length is 5m.
• When the outdoor unit is placed at a higher level than the
indoor unit, provide a trap near the hose's lead-in port.
Use the refrigerant pipes shown in the table below.
Pipe size
Liquid side
Gas side
• The thermal insulation should cover both the gas and liquid
Length unit: mm
pipes.
OUTDOOR UNIT
AE-Z25TR
AE-Z35TR
.
.
ITEMS Q'ty
9 To secure the electrical
cable.
1
10 MANUALS Installation manual
1
Operation manual
1
11 SHEET
(adhesive type)
cal cable.
1
12 DROPPER To check the drain hose.
1
water.
advisable as freezing could result.
.
breakdown.
Outdoor
unit
Max. Min. Additional
height piping refrigerant
difference: length (piping length
B exceeds 10m)
10m 3m 20g/m
Pipe thickness
1/4"
(ø 6.35 mm)
0.8 mm
B617
APPLICATION
-
where the unit can be
Trap
Chargeless
max
pipe
length
10m
Thermal insulation
Thickness: 6 mm or
thicker
Material: Polyethyl-
ene foam