Related Manuals for AUSTRALIAN MONITOR AM3002
Summary of Contents for AUSTRALIAN MONITOR AM3002
- Page 1 Australian Monitor AM3002 Ausbdlan Monitor H+," -tr' \i" r;-r "''.r.. t: \:. I ;\"/ \\1i. [ ,lt_, -__:,vi:_. Operation Manual...
- Page 2 DO NOT OPEN nearest agent Australian Monitor direct: The presence ofan EXCLAMATION MARKcontained OFFICER THE TECHNICAL within the boundaries of an equilateral triangle AUSTRALIANMONITOR alert the user thal there...
- Page 3 Mains circuit Breaker. chain mains swilching turn-on. breaker. cunent lnput muting lndividual high rail protedion. grounding, decoupling componentry lnputovervoltage Layout, suppression. have been oplimized to provide the user with Radio-frequency interference indication. stability, reliability Short-circuit protection longevity. Australian Monitor...
-
Page 4: Table Of Contents
Contents Page lntroduction Controls, Connectors and lndicators 2.1 Front Panel 2.2RearPanel lnstallation Operation Bridge Mode TwoOhmorNotTwoOhm Maintenance Wananty Specification List of Illustrations Page Figure Block Diagram Figure2. Front Panel Layout Figure 3. Rear Panel Layout Figure 4. Case Dimensions "Speakon" Connector Wiring Figure Figure 6. -
Page 5: Lntroduction
Introduction Introduction rack mountable unils. Congratulations on choosing Australian Monitor for ofthe amplifier yourprofessional Each channel comprises balanced requirements. amplifi cation active input with an attenuator driving differential The design of your class drive stage which turn drives fan-cooled, Audio Power Amplifier... -
Page 6: Controls, Connectors And Lndicators
& Controls Connectors Controls, Connectors &, Indicators Figure Front Panel Layout... -
Page 7: Front Panel
& Connectors Controls Front Panel erestablishment Currenl Suppression of lnrush circuil the LED will extinguish. This LED will not the panel layout Figure shows of the AN30O2. illuminate during amplifier. normal funclions ofthe controls and indicators follows: thermal overload this LED will the advent of internaloperating Attenuator... - Page 8 & Controls Connectors <ii!ru t:.;J ...'" Rear Panel Layout Figure...
-
Page 9: Rearpanel
-The Fault lndicatorwilllight and pulse sync. The wires in programsourceif mains lead are coloured Rail with the negative supply Breaker "lrips". accordance with the following code: BROVITN ACTIVE; BLUE NEUTRAL; GREENANDYELLOW EARTH. CAUTION Your amplifier must always earthedl Australian Monitor... -
Page 10: Figure 4. Case Dimensions
Installation 4a2-5 l19.OO"l Austrdian Monitor 5?.15 133.O 2-26"1 15.2i1"1 461.1 118.16"1 13?.O 117.20"1 "J:( I l")< ^;-'fl.tr li" "ri!!!ll' ')ll 111.', =l:lr L:"i l; ll:.1 '*Dr ll _-w._ i:" t 33,O t:g: .i l1: l: r:F: 3.A2"1 15.24"t !:l-L9l o^r l/a^\, .ffi lYll... -
Page 11: Lnstallation
Please refer lead temperalure (1280 exceeds 600C personnel. Australian Monitor takes responsibility for any damage or ha]m resulting unrestricted airflowinto outfromthe unit must from improper termination of this leadl provided. Any restriction... -
Page 12: Speakon" Connector Wiring
Installation When using SPEAKoN NEUTRIK (NL4MP) NOTE: ln-lineXLR ofien alermination nectors have for speaker output, use only the mating connecisdirec{lyto connector that the chassis connector. to pin this amplifier's input as NEUTRIK connector. connector link NL4FC in-line This grounding scheme. that both channels can be fed from will defeat the amplifier's... -
Page 13: Operation
(fully "0" attenuator is at clockwise) nominally: REMEMBER +3.3dBu lastpieceof equipmentthat forrated powerinto The amplifi ershould bethe 4volts (1.1 piece equipment that load. off. +2.2dBu powerintoa turn (1.00 volt for rated your the altenuators on recommend turning load- Australian Monitor... - Page 14 Operation your amplifier has Each channel produces nominal voltage thewire's resistance. drop due input impedance 2SkOhms (@1kHz) voltage difference between the amp earth and balanced This present equipment earth appears to the amplifier's difficult forany signal should load source source. input as signal and is amplified as hum.
-
Page 15: Bridge Mode
BRIDGE speakon lead with of your amplifier ground, or off, (either amplifier output Whilst - be careful). connedthe sourcelothe Channel-Afemale output oulput signal inputXLR. PRASt NEVEFgE LEAO trtr; ".^., |@Jm ,a" h:Al,{ Figure Bridge Mode Speaker Connection Australian Monitor... -
Page 16: Twoohmornottwoohm
Ohm or Not Two Ohm given Two Ohm or loadfora sinewave excursion resistive into this is in line with the frequency. Though method gives Not Two Ohm indication variousslandardsthat exist, only (before clipping) for tothe maximum voltage s,wing ofrating powerdoes notgive given load. -
Page 17: Maintenance
Maintenance T.Maintenance will Your amplifier need AM3002 minimal Overtime, edgeof dust may build the leading maintenance. No internal adjustments need to and reduce their cooling efficiency. fan blades maintain optimum performance. made Thelime unit to taken forthis happen willdepend environment amount use. -
Page 18: Wananty
AC mains void this warranty' connection to faulty equipment, modification priorfactoryapprovalorservice Australian Monitor accepts no liability for alteration withorJt personnel. direct consequential damages, whether by unauthorised indirect, arising from the use or misuse of its... -
Page 19: Specification
Specification ltJlz}.loh / 1.0%THD+N(inwatts) Output Power @ 8ohm l2,ol0 l,t6o 1,290 1,200 Single Channel r,730 Both Channels 1,600 1,080 1,150 1,800 Rating(AVG) 6'70 1,180 2,2s0 3,460 2,12s 3,200 Brideed 2,kllz +N (inwatts) Output Power 20Hz to @ 1% 1,750* 1,100 Channel Single 1,600{'... - Page 20 Australian Monitor com. au ian mon itor. www. stra Distributed Audio Telex Communications Pty Ltd ACN001345482 audiotelex. com. au www. lnternational Enquiries Ph: 612 9647 48 2537, E-mail: ho@audiotelex.com.au 41 1, Sydney Ph: (02) (02) 9648 3698, E-mail: nsw@audiotelex.com. au...
Need help?
Do you have a question about the AM3002 and is the answer not in the manual?
Questions and answers