Related Manuals for East Tester ET432
Summarization of Contents
Safety Information
Safety Instructions and Symbols
Important safety warnings, symbols, and environmental conditions for operation.
Introduction and Package Contents
Packing List
Lists all items included in the product package for user verification.
Front Panel Overview
Front Panel Controls and Display
Details the functions of the instrument's front panel buttons and LCD display.
User Interface Navigation
Measurement Interface Details
Explains the components and indicators of the main measurement display screen.
System Settings Interface
Describes the system settings screen and configurable options like language and power.
Test Port Configuration
Details the 3- and 5-terminal test ports and their connectivity for measurements.
Operation Instructions
Startup and Shutdown Procedures
Instructions for powering the instrument on and off correctly.
Parameter Selection Guide
How to select various measurement parameters like frequency and level.
Signal Level Selection
How to change the AC test signal voltage level for measurements.
Internal Bias Voltage Setting
How to set the internal DC bias voltage for specific measurements.
Measurement Range Selection
Methods for selecting the appropriate measurement range for accuracy.
Measurement Speed Settings
How to adjust the measurement speed (fast, medium, slow) for optimal results.
Main Parameter Selection (L/C/R/Z)
How to select the primary measurement parameter (L, C, R, Z, or Auto).
Secondary Parameter Selection (X/D/Q/ESR)
How to select secondary measurement parameters like D, Q, ESR.
Tolerance Setting for Comparator
How to set tolerance limits for component comparison using the comparator.
Nominal Value Setting
How to set the nominal value for component comparison with the comparator.
Equivalent Circuit Model Selection
Choosing between series and parallel equivalent models for measurement accuracy.
DCR Measurement Mode
How to enter and use the DC Resistance (DCR) measurement mode.
Electrolytic Capacitance Mode
How to enter and use the mode for measuring electrolytic capacitors.
Relative Measurement Mode
Using the relative mode for measurements against a stored reference value.
Reading Hold Function (HOLD)
Freezing displayed measurement data on the LCD screen.
Data Recording (Max, Min, Avg)
Recording and displaying maximum, minimum, and average measurement readings.
Comparator Function
Using the comparator to check if measured values are within set tolerance limits.
Open/Short Circuit Correction
Performing open and short circuit corrections to reduce test lead errors.
Rapid Application Guide
Resistance Measurement Guide
Step-by-step instructions for connecting and measuring resistance.
Capacitance Measurement Guide
Step-by-step instructions for connecting and measuring capacitance.
Inductance Measurement Guide
Step-by-step instructions for connecting and measuring inductance.
Impedance Measurement Guide
Step-by-step instructions for connecting and measuring impedance.
PC Communication and Control
PC Connection and Driver Installation
Steps for connecting the instrument to a PC and installing necessary drivers.
Virtual Serial Port Configuration
Details serial port communication parameters for PC connection.
Remote Control State Management
How the instrument enters and exits remote control mode via PC.
SCPI Command Protocol
Explains the SCPI command set for instrument control and data acquisition.
Query Return Format
Describes the format of data returned by query commands from the PC.
Data Types for ASCII Transmission
Lists the data types used in ASCII character transmission over the bus.
Command Syntax Conventions
Explains the meaning of special marks used in command syntax.
Command Abbreviations and Capitalization
Rules for command abbreviations and capitalization in SCPI.
Instrument Specifications
General Instrument Parameters
Table of general specifications for ET43 series models.
Measurement Accuracy Specifications
Details the accuracy of L, C, R, Z, X measurements.
Accuracy Indicator Details
Notes and general conditions for accuracy measurements.
Accuracy Indicator for ET433
Accuracy specifications for the ET433 model at specific test levels.
Accuracy Indicator for ET432/ET431
Accuracy specifications for ET432 and ET431 models at specific test levels.
Accuracy Indicator for ET430/ET430B
Accuracy specifications for ET430 and ET430B models.
Accuracy Indicator for DCR Measurement
Accuracy specifications for DC Resistance (DCR) measurements.
Maintenance and Care
Overhaul and Troubleshooting
Procedures for basic checks and identifying equipment failures.
Cleaning Procedures
Instructions for safely cleaning the instrument to maintain performance.
Need help?
Do you have a question about the ET432 and is the answer not in the manual?
Questions and answers