Table of Contents
Advertisement
Quick Links
INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.
NOTICE: DO NOT discard this manual!
Models:
TRUE-36G-IFT
TRUE-36TG-IFT
TRUE-36S-IFT
TRUE-42G-IFT
TRUE-42TG-IFT
TRUE-42S-IFT
TRUE-50TG-IFT
TRUE-50S-IFT
This appliance may be installed as an OEM
installation in manufactured home (USA
only) or mobile home and must be installed
in accordance with the manufacturer's
instructions and the Manufactured Home
Construction and Safety Standard, Title 24
CFR, Part 3280 in the United States, or the
Standard for Installation in Mobile Homes,
CAN/CSA Z240 MH Series, in Canada.
This appliance is only for use with the type(s)
of gas indicated on the rating plate. This
appliance is not convertible for use with other
gases, unless a certified kit is used.
Pour demander un exemplaire en français de ce Manuel du
propriétaire, visitez www.heatnglo.com/translations.
Heat & Glo • TRUE-36-IFT, TRUE-42-IFT, TRUE-50-IFT Installation Manual • 2461-980 Rev. Q • 11/20
Installation Manual
Installation and Appliance Setup
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death, or
property damage.
• DO NOT store or use gasoline or other flam-
mable vapors and liquids in the vicinity of this
or any other appliance.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Leave the building immediately.
- Immediately call your gas supplier from
a neighbor's phone. Follow the gas sup-
plier's instructions.
- If you cannot reach your gas supplier, call
the fire department.
• Installation and service must be performed
by a qualified installer, service agency, or the
gas supplier.
DANGER
DO NOT TOUCH GLASS
NEVER ALLOW CHILDREN
A barrier designed to reduce the risk of
burns from the hot viewing glass is provided
with this appliance and must be installed for
the protection of children and other at-risk
individuals.
In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fitter.
See Table of Contents for location of additional Commonwealth
of Massachusetts requirements.
HOT GLASS WILL
CAUSE BURNS.
UNTIL COOLED.
TO TOUCH GLASS.
1
Advertisement
Table of Contents
Related Manuals for Heat&Glo TRUE-50-IFT
Summarization of Contents
Product Specific and Important Safety Information
Appliance Certification
Details the appliance's certification standards and approvals.
Glass Specifications
Specifies the type and properties of the appliance's glass.
BTU Specifications
Lists the input BTU ratings for different models and gas types.
High Altitude Installations
Provides guidelines for installing the appliance at elevated altitudes.
Non-Combustible Materials Specification
Defines materials considered non-combustible for installation.
Combustible Materials Specification
Defines materials considered combustible for installation.
Electrical Codes
Outlines electrical wiring requirements and code compliance.
California
Addresses California-specific warnings regarding chemicals.
Requirements for the Commonwealth of Massachusetts
Details specific installation requirements for Massachusetts.
Getting Started
Design and Installation Considerations
Covers initial planning and site selection for installation.
Good Faith Wall Surface
Illustrates wall surface temperature guidelines above the appliance.
Tools and Supplies Needed
Lists the necessary tools and supplies for installation.
Inspect Appliance and Components
Instructions for unpacking and checking appliance parts.
Framing and Clearances
Appliance/Decorative Front Dimension Diagrams
Provides diagrams and dimensions for appliance and front fit.
Clearances to Combustibles
Specifies required distances from combustible materials.
Constructing the Appliance Chase
Guidance on building an enclosure for the appliance and vent.
Hearth Extension
Details requirements for hearth extensions in front of the appliance.
Termination Location and Vent Information
Vent Termination Minimum Clearances
Defines minimum clearances for vent termination locations.
Chimney Diagram
Illustrates chimney configuration and clearances.
Approved Pipe
Lists approved venting pipe types and system components.
Use of Elbows
Explains the use and limitations of vent elbows.
Measuring Standards
Details the standards used for vent measurement.
Vent Diagrams
Provides diagrams for vent configurations and lengths.
PVLP-SLP and PVI-SLP-B Information
Specifics on power vent kit installation and baffle adjustment.
Vent Clearances and Framing
Pipe Clearances to Combustibles
Specifies clearances for vent pipes to combustible materials.
Wall Penetration Framing/Firestops
Instructions for framing and installing firestops for wall penetrations.
Ceiling Firestop/Floor Penetration Framing
Guidance for framing and installing firestops for ceiling/floor penetrations.
Install Attic Insulation Shield
Details the installation of attic insulation shields for vent safety.
Prepare for Heat Management
Steps for preparing the appliance for heat management systems.
Appliance Preparation
Vent Collar Preparation
Steps for preparing the appliance's vent collar.
Securing and Leveling the Appliance
Instructions for securely mounting and leveling the appliance.
Installing Non-Combustible Facing Material
Guidance on applying non-combustible materials around the appliance.
Venting and Chimneys
Assemble Vent Sections
Detailed steps for connecting vent pipe sections.
Secure the Vent Sections
Guidelines for supporting and securing vent pipe runs.
Disassemble Vent Sections
Procedure for taking apart vent sections.
Vertical Termination Requirements
Specifies requirements for vertical vent pipe termination.
Horizontal Termination Requirements
Specifies requirements for horizontal vent pipe termination.
Electrical Information
General Information
Covers basic electrical requirements, safety, and component installation.
Wiring Requirements
Details wiring for the IntelliFire Touch ignition system.
Gas Information
Fuel Conversion
Instructions for converting the appliance between gas types.
Gas Pressure
Specifies required gas pressures for optimal performance.
Gas Connection
Outlines procedures for connecting the gas supply line.
High Altitude Installations
Guidelines for installing the appliance at high altitudes.
Air Shutter Setting
Procedures for adjusting the air shutter for proper flame appearance.
Finishing
Facing Material
Guidelines for applying non-combustible facing materials.
Finishing Templates
Information on using templates for finishing materials.
Mantel and Wall Projections
Specifies clearances for mantels and wall projections.
Decorative Front Dimensions for Finishing
Provides dimensions for decorative fronts and finishing methods.
Appliance Setup
Fixed Glass Assembly
Instructions for installing or removing the fixed glass assembly.
Remove the Shipping Materials
Steps to remove protective shipping materials from the appliance.
Clean the Appliance
Guidance on cleaning the appliance after installation.
Install Glass Refractory (TRUE-36G-IFT/TRUE-42G-IFT Only)
Detailed steps for installing the glass refractory panels.
Install Teco-Sil and Mystic Embers
Procedure for applying Teco-Sil and mystic embers for aesthetic effect.
Glowing Ember Placement
Instructions for correctly placing glowing embers for burner operation.
LED's
Notes that LEDs are factory installed and require no setup.
IntelliFire Touch® Control System Setup
Steps for setting up the IntelliFire Touch control system.
Install Decorative Front
Guidance for installing approved decorative fronts.
Reference Materials
Vent Components Diagrams
Diagrams and specifications for various vent system components.
Accessories
Lists available optional accessories for the appliance.
Need help?
Do you have a question about the TRUE-50-IFT and is the answer not in the manual?
Questions and answers