Table of Contents
Advertisement
RS-232 and Telnet Command Set / Protocol Specifications
3.7 SET REBOOT DELAY
Assign the delay between the last outlet turning off and the beginning of the turn on se-
quence in a reboot cycle.
3.7.1
Command:
3.7.2
Response:
Where
3.8 SET DELAY
Assigns the turn on and turn off delays for an outlet OUTLET or DC trigger output.
3.8.1
Command:
3.8.2
Action:
3.8.3
Response:
3.9 SET FEEDBACK MODE
Sets the feedback to ON (unsolicited) or OFF (polled). When ON, a message will be sent to
the controller every time the status of an input (i.e. trigger), output (i.e. outlet) or power state
(i.e. overvoltage) changes. If feedback is OFF, the controller must poll for state changes.
3.9.1
Command:
3.9.2
Action:
3.9.3
Response:
3.10 SET LINEFEED MODE
Controls the linefeeds (ASCII: 10d, 0Ah) sent with each response. When ON, each response
will end with a linefeed. When OFF, all responses will not end with a linefeed.
3.10.1
Command:
!SET_REBOOT_DELAY button_1 button_2<CR>
Example: !SET_REBOOT_DELAY 30 5<CR>
(sets the reboot delay for Button_1 to 30
seconds and the delay for button_2 to 5
seconds.)
If button_1 button_2 are valid:
$BUTTON_1 DELAY = button_1<CR>
$BUTTON_2 DELAY = button_2<CR>
If button_1or button_2 are not valid:
$INVALID_PARAMETER<CR>
button_1 = { 1-255 } (seconds)
button_2 = { 1-255 } (seconds)
!SET_DELAY outlet ondelay offdelay<CR>
outlet = { 1..8 }
ondelay = { 0-255 } (seconds)
offdelay = { 0-255 } (seconds)
Example: !SET_DELAY 4 5 1<CR>
(sets outlet 4 turn-on delay to 5 sec. and
turn-off delay to 1 sec.)
Sets the turn on delay for outlet to ondelay
Sets the turn off delay for outlet to offdelay
If outlet, ondelay and offdelay are valid:
$DELAY FOR outlet = ondelay offdelay<CR>
If outlet, ondelay or offdelay are invalid:
$INVALID_PARAMETER<CR>
!SET_FEEDBACK mode<CR>
mode = { ON, OFF }
Sets the feedback mode to mode.
If mode = ON, $FEEDBACK = ON<CR>
If mode = OFF, $FEEDBACK = OFF<CR>
If mode is invalid, $INVALID_PARAMETER<CR>
!SET_LINEFEED mode<CR>
mode = { ON, OFF }
3.10.2
Action:
3.10.3
Response:
3.11 RESET FACTORY SETTINGS
Resets all of the custom configuration settings (i.e. triggers, delays, feedback mode,
& linefeed mode) to their original factory settings listed below.
3.11.1
Command: !RESET_ALL<CR>
3.11.2
Action:
Resets the configuration below:
TRIGGER FOR 1
TRIGGER FOR 2
TRIGGER FOR 3
TRIGGER FOR 4
TRIGGER FOR 5
TRIGGER FOR 6
TRIGGER FOR 7
TRIGGER FOR 8
DELAY FOR 1
DELAY FOR 2
DELAY FOR 3
DELAY FOR 4
DELAY FOR 5
DELAY FOR 6
DELAY FOR 7
DELAY FOR 8
REBOOT1 DELAY
REBOOT2 DELAY
FEEDBACK = ON
LINEFEED = ON
PROFILE = 1
3.11.3 Response:
$FACTORY SETTINGS RESTORED<CR>
3.12 SET PROFILE
Sets all of the custom configuration settings (i.e. triggers, delays, feedback mode,
& linefeed mode) to the profile selected. The settings are listed below.
3.12.1
Command: !SET_PROFILE n<CR>
Where n is 1,2,3,4
3.12.2
Action:
P1 configuration is the same as !RESET_ALL
3.12.3
Action:
P2 configuration below:
TRIGGER FOR 1
TRIGGER FOR 2
TRIGGER FOR 3
TRIGGER FOR 4
TRIGGER FOR 5
TRIGGER FOR 6
TRIGGER FOR 7
TRIGGER FOR 8
DELAY FOR 1
DELAY FOR 2
DELAY FOR 3
DELAY FOR 4
DELAY FOR 5
DELAY FOR 6
DELAY FOR 7
DELAY FOR 8
9
(Continued)
Sets the linfeed mode to mode.
If mode = ON, $LINEFEED = ON<CR>
If mode = OFF, $LINEFEED = OFF<CR>
If mode is invalid, $INVALID_PARAMETER<CR>
= BUTTON_1, GREEN_BUTTON
= BUTTON_2, GREEN_BUTTON
= GREEN_BUTTON
= GREEN_BUTTON
= GREEN_BUTTON
= GREEN_BUTTON
= DC_TRIGGER, GREEN_BUTTON
= DC_TRIGGER, GREEN_BUTTON
= 1,16
= 2,15
= 3,14
= 4,13
= 5,12
= 6,11
= 7,6
= 12,1
= 30
= 30
= BUTTON_1, GREEN_BUTTON
= BUTTON_1, GREEN_BUTTON
= BUTTON_2, GREEN_BUTTON
= GREEN_BUTTON
= GREEN_BUTTON
= GREEN_BUTTON
= DC_TRIGGER, GREEN_BUTTON
= DC_TRIGGER, GREEN_BUTTON
= 1,16
= 16,15
= 17,14
= 18,13
= 19,12
= 20,11
= 21,6
= 26,1
Hide quick links:
Advertisement
Table of Contents
