Toyota RAV4 (RHD) - MMC Installation Instructions Manual
Toyota genuine audio installation instructions for rav4 (rhd) - mmc **a2*r
Hide thumbs
Also See for RAV4 (RHD) - MMC:
- Owner's manual (764 pages) ,
- Manual (484 pages) ,
- Operation manual (228 pages)
Related Manuals for Toyota RAV4 (RHD) - MMC
Summary of Contents for Toyota RAV4 (RHD) - MMC
- Page 1 Toyota Genuine Audio INSTALLATION INSTRUCTIONS RAV4 (RHD) - MMC (Production date 08/03) Manual Ref. n° A3RA2/W-2-0 TOYOTA MOTOR CORPORATION...
-
Page 2: Table Of Contents
TABLE OF CONTENTS 1. Audio Application Chart ............................. 2. System Layout ................................3. 1.4Din Audio Installation ............................4. Wide 2Din Audio Installation ............................5. Seat Mounted CD-Changer Installation (Passenger Seat) ..................6. Subwoofer Installation ............................... RAV4 (RHD) - 3 11-03... -
Page 3: Audio Application Chart
p. 1/2... - Page 4 p. 2/2...
-
Page 5: System Layout
2. SYSTEM LAYOUT 2.1 CD-CHANGER INSTALLATION UNDER THE PASSENGER SEAT NOTE: To install the CD-changer in hanging position under the passenger seat, you will need the seat-mounted 6 CD-changer TM0461 (08601-00912) and the seat-mounting kit F/K (08695-00803). RAV4 (RHD) - 6 11-03... -
Page 6: 4Din Audio Installation
3. 1.4DIN AUDIO INSTALLATION Remove the covers : Clip (6x) Fig. 1 Remove the centre cluster panel : Clip (3x) : Screw (2x) Fig. 2 Remove the accessory boxes cover plates : Screw (4x) Fig. 3 RAV4 (RHD) - 7 11-03... - Page 7 4 to 5. Fig. 5 IN CASE OF 1.4DIN COMBO + 0.6DIN COVER PLATE Fit the 0.6-DIN cover plate Mount the brackets (2x) onto the 1.4 DIN combo and 0.6DIN cover plate : Screw (6x) Fig. 6 RAV4 (RHD) - 8 11-03...
- Page 8 Install the assembly (1.4DIN combo + 0.6DIN add on unit or 1.4DIN combo + 0.6DIN cover plate). : Screw (4x) ENSURE THAT ALL REMOVED CONNECTORS ARE PUT BACK CORRECTLY. REFIT THE TRIM AND REMOVED PARTS. Fig. 9 RAV4 (RHD) - 9 11-03...
-
Page 9: Wide 2Din Audio Installation
4. WIDE 2DIN AUDIO INSTALLATION Remove the covers : Clip (6x) Fig. 10 Remove the centre cluster panel : Clip (3x) : Screw (2x) Fig. 11 Remove the accessory boxes cover plates : Screw (4x) Fig. 12 RAV4 (RHD) - 10 11-03... - Page 10 (10P/6P), the AVC-connec- tor (12P), the display connector (18P) and the antenna. : Screw (4x) ENSURE THAT ALL REMOVED CONNECTORS ARE PUT BACK CORRECTLY. REFIT THE TRIM AND REMOVED PARTS. Fig. 15 RAV4 (RHD) - 11 11-03...
-
Page 11: Seat Mounted Cd-Changer Installation (Passenger Seat)
SEAT MOUNTED CD-CHANGER INSTALLATION (Passenger Seat) Remove the covers : Clip (6x) Fig. 16 Remove the centre cluster panel : Clip (3x) : Screw (2x) Fig. 17 Remove the accessory boxes cover plates : Screw (4x) Fig. 18 RAV4 (RHD) - 12 11-03... - Page 12 : Cover (2x) Fig. 19 Remove the front door scuff plate (L) and kick panel (L) and side cover (L). : Clip (1x) : Nut (1x) Fig. 20 Cut the tape into 10 pieces. Fig. 21 RAV4 (RHD) - 13 11-03...
- Page 13 ONLY IN CASE OF FULL MAP NAVIGATION Connect the conversion harness (08695-00370). Fig. 22 Remove the side cover (L) and the knob of the passenger seat : Screw (2x) Fig. 23 RAV4 (RHD) - 14 11-03...
- Page 14 : Bolt (M5x9) (4x) CAUTION : Nut (M6) (4x) : Damper (“6CDN” Mark) (4x) CAUTION Loosen the screws before moving them. Screw up after the position is changed. Holes Location Left “6CDN”mark Right “6CDN”mark Fig. 25 RAV4 (RHD) - 15 11-03...
- Page 15 : Bolt (M5x9) (2x) Hole Location ‘D’ Hole Location ‘B’ Fig. 26 13. Fit the sub bracket (L) to the side bracket (L). : Bolt (M5x9) (2x) Hole Location ‘B’ Hole Location ‘D’ Fig. 27 RAV4 (RHD) - 16 11-03...
- Page 16 : Bolt (M6x12) (2x) : Bolt (M6x25) (1x) Replace the side cover (L) and the knob onto the passenger seat left hand (see figure 23). Fig. 29 16. Connect the changer wire to the CD-changer Fig. 30 RAV4 (RHD) - 17 11-03...
- Page 17 17. Fit the CD-changer to the sub brackets (R) + (L), under the passenger seat using nuts : Nut (M6) (4x) Fig. 31 ENSURE THAT ALL REMOVED CONNECTORS ARE PUT BACK CORRECTLY. REFIT THE TRIM AND REMOVED PARTS. RAV4 (RHD) - 18 11-03...
-
Page 18: Subwoofer Installation
: Screw (4x) Fit the cushion tape to the sub- woofer : Cushion tape (10mm) (2x) Fig. 32 Cut the carpet as shown in the illustra- tion. 20mm 20mm 45mm 100mm 75mm 249mm Fig. 33 RAV4 (RHD) - 19 11-03... - Page 19 Pull back the floor carpet Route and tape the subwoofer wire harness as shown. Fig. 35 Connect the subwoofer wire harness to the 10P audio connector of the vehicle wire harness and to the audio unit. Audio Fig. 36 RAV4 (RHD) - 20 11-03...
- Page 20 : Cap (4x) : Nut (M5) (4x) Connect the subwoofer wire to the subwoofer Fig. 38 ENSURE THAT ALL REMOVED CONNECTORS ARE PUT BACK CORRECTLY. REFIT THE TRIM AND REMOVED PARTS. RAV4 (RHD) - 21 11-03...
- Page 21 GENUINE PARTS...