Mode-Cw Group - Yaesu FTDX5000 Operating Manual

M M
ENU ODE
053 A1A LCUT FRQ
Function: Selects the cutoff frequency of the lower side
of the RX audio filter in the CW mode.
Available Values: OFF / 100 Hz ~ 1000Hz (50 Hz/step)
Default Setting: 300Hz
054 A1A LCUT SLP
Function: Selects the filter slope of the lower side of the
RX audio filter in the CW mode.
Available Values: 6dB/oct or 18dB/oct
Default Setting: 18dB/oct
055 A1A HCUT FRQ
Function: Selects the cutoff frequency of the upper side
of the RX audio filter in the CW mode.
Available Values: OFF / 700Hz ~ 4000Hz (50 Hz/step)
Default Setting: 1000Hz
056 A1A HCUT SLP
Function: Selects the filter slope of the upper side of the
RX audio filter in the CW mode.
Available Values: 6dB/oct or 18dB/oct
Default Setting: 6dB/oct
057 A1A F-TYPE
Function: Selects the desired keyer operation mode for
the device connected to the front panel KEY jack.
Available Values: OFF / BUG / ELEKEY / ACS
Default Setting: ELEKEY
OFF: Disables the front panel keyer (use this
mode with a straight key, an external keyer,
or a computer-driven keying interface).
BUG: Mechanical "bug" keyer emulation. One
paddle produces "dits" automatically, while
the other paddle manually produces "dahs."
ELEKEY: Iambic keyer with ACS (Automatic Char-
acter Spacing) disabled.
ACS: Iambic keyer with ACS (Automatic Char-
acter Spacing) enabled.
058 A1A F-REV
Function: Selects the keyer paddle's wiring configuration
for the KEY jack on the front panel.
Available Values: NOR / REV
Default Setting: nor
NOR: Tip = Dot, Ring = Dash, Shaft = Ground
REV: Tip = Dash, Ring = Dot, Shaft = Ground
Page 126
MODE-CW G
ROUP
059 A1A R-TYPE
Function: Selects the desired keyer operation mode for
the device connected to the rear panel KEY jack.
Available Values: OFF / BUG / ELEKEY / ACS
Default Setting: ELEKEY
OFF:
BUG:
ELEKEY: Iambic keyer with ACS (Automatic Char-
ACS:
060 A1A R-REV
Function: Selects the keyer paddle wiring configuration
for the KEY jack on the rear panel.
Available Values: NOR / REV
Default Setting: nor
NOR: Tip = Dot, Ring = Dash, Shaft = Ground
REV: Tip = Dash, Ring = Dot, Shaft = Ground
061 A1A CW AUTO
Function: Enables/disables CW keying while operating
on SSB.
Available Values: OFF / 50M / ON
Default Setting: OFF
OFF: Disables CW keying while operating on SSB.
50M: Enables CW keying only while operating SSB
ON: Enables CW keying while operating on SSB (all
N :
OTE
This feature allows you to move someone from SSB to
CW without having to change modes on the front panel.
062 A1A BFO
Function: Sets the CW carrier oscillator injection side for
the CW mode.
Available Values: USB / LSB / AUTO
Default Setting: USB
USB:
LSB:
AUTO: Injects the CW carrier oscillator on the LSB
Disables the rear panel keyer (use this mode
with a straight key, an external keyer, or a
computer-driven keying interface).
Mechanical "bug" keyer emulation. One
paddle produces "dits" automatically, while
the other paddle manually produces "dahs."
acter Spacing) disabled.
Iambic keyer with ACS (Automatic Char-
acter Spacing) enabled.
on 50 MHz (but not HF).
TX bands).
Injects the CW carrier oscillator on the USB
side.
Injects the CW carrier oscillator on the LSB
side.
side while operating on the 7 MHz band and
below, and the USB side while operating on
the 10 MHz band and up.
FT 5000 O
DX PERATING
M
ANUAL