K&H Cool Bed III Care Instructions

Cool Bed III
Care & Instructions
Thank you for purchasing the COOL BED III by K&H Pet Products. The Cool Bed III should provide years of soft,
cool, gel-like sleeping comfort for your dog. Please read all instructions before using this product.
USE INSTRUCTIONS
Read all instructions carefully.
HOW TO FILL & USE YOUR COOL BED III:
1
Remove the Cool Bed III from the box. Locate the
filler cap on the bed and open it by grasping the
base of the cap with one hand and the tab of the
cap with the other. Pull the cap open. See Figure a.
Flatten the Cool Bed III and let it sit for a few
minutes to allow the cool core interior to retain its
shape as all air has been removed for shipping.
2
Place the Cool Bed III in the intended location
with the cap side of the bed up for filling. Place a
towel under the filler cap end of the bed to absorb
any accidentally spilled water. Using a calibrated
container with a pour spout, begin carefully filling
the Cool Bed III with cool water. See Figure b.
The bed will take the following water quantities:
SMALL Cool Bed III: 1- 1 .5 gallons
MEDIUM Cool Bed III: 2-3 gallons
LARGE Cool Bed III: 4-6 gallons
Keep in mind, the more water used, the more cushioning and cooling
capabilities the bed will have. You can experiment for the optimal feel of
the Cool Bed III. Ultimately the recommended quantity of water for best
cooling capabilities is as listed above.
3
Now that you have your Cool Bed III filled, close
the filler cap and begin to knead the bed to help
work the water into the Cool Core. See Figure c.
Now pull open the air adjustment valve and gently
work as much air out as you can, using sweeping
motions across the Cool Bed III with your hands.
Sweep the air towards the valve allowing the
air to expel from the bed. Seal the valve when most of the air has been
removed. You will feel how comfortable the bed will be at this point. The
bed should feel very soft and spongy and you should feel water squishing
around inside the bed. Now decide if a little more water is desirable
or if it's just right for your pet. Add water if necessary, repeating the air
removal process. Note: A little air inside the bed will not affect the cooling
capabilities of the Cool Bed III. If you choose, you may expel air as
needed though not necessary.
HOW TO EMPTY YOUR COOL BED III:
1
Open the filler cap.
2
Roll bed from opposite end, expelling water out of the cap. (Much like
rolling a sleeping bag)
3
Store with filler cap open.
K&H Pet Products with design is a registered trademark of Central Garden & Pet Company.
©2008 - 2020 Central Garden & Pet Company
!
IMPORTANT TIPS & TRICKS:
MOVING YOUR COOL BED III:
Do not lift or move the bed by
its corners as this will cause the foam
core interior to separate from the
sides. Fold the bed and wrap each
arm around either end of the bed to
move. (See Figures c & d)
a CLEANING OR STORING: Grapefruit Seed Extract is an all natural, non-toxic
antibacterial. Add it to the water when filling and place a few drops in before
storing to help prevent bacterial growth.
HOW TO USE COOL BED III:
The best results will be obtained when used in a shady area. When using outdoors,
always place the Cool Bed III in a shady, cool spot, as this will maximize its heat
wicking abilities. Be sure not to place the bed on sharp objects that could puncture
the Cool Bed III. Keeping the Cool Bed III indoors overnight near air conditioning
will super cool the bed for outdoor use the next morning. When using indoors, be
b
sure to place the Cool Bed III out of direct sunlight. The cooler the spot you place
the Cool Bed III, the better. An ideal place would be a cool tile, linoleum or concrete
floor. An area with good air movement will also help keep the bed cooler. You will
soon figure out the best location for your new Cool Bed III, and your pet will love
you for it!
HOW DOES THE COOL BED III WORK?
Unlike a fluffy dog bed that is designed to retain heat to keep a dog warm, the
Cool Bed III is designed to radiate heat back into the air or the floor surface to keep
a dog cool. The water-saturated Cool Core inside the Cool Bed III absorbs the dog's
natural body temperature of 102º Fahrenheit and coverts it to room temperature,
which is normally well below the dog's body temperature. The difference created
between the room temperature and the dog's body temperature is how the Cool
Bed III provides a cooler, refreshing surface for your dog. Even if it is 80ºF in your
house, the Cool Bed III is 22º cooler than a dog's 102º body temperature. The Cool
Bed III provides a permanent, natural, "cool" spot for your dog, inside or outside in
temperatures under 95º Fahrenheit without chemicals or electricity.
•
Have your dog's nails routinely trimmed to prevent accidental punctures.
•
The Cool Bed III should be placed on a smooth surface that cannot cause
punctures, abrasions or leakage.
c
•
Routinely check under your Cool Bed III for moisture.
•
The surface can be cleaned using a damp towel or sponge and mild dish washing
detergent. Do not wash in a washing machine.
•
Never use the Cool Bed III in direct sunlight. Always place in shade, as direct sun
will warm the Cool Bed III.
•
Always place the Cool Bed III out of the way of foot traffic.
•
Never allow the Cool Bed III to freeze.
•
Cool Bed III is not intended to be a life saving device.
•
This product is to be used in temperatures under 95° Fahrenheit.
Our warranty is as follows: K&H Pet Products warrants to the original consumer, that this
product will be free of defects and workmanship for a period of two years from the date of
purchase. The manufacturer's liability hereunder is limited to replacement of the product. This
warranty is void if the product has been damaged by accident, unreasonable use, neglect,
tampering, or other causes not arising from defects in material and workmanship.
To exercise your warranty: If, during the warranty period, your product malfunctions,
return it to the place of purchase with your original purchase receipt. If this cannot be
done, return the product, postage prepaid, to K&H Pet Products, with a dated proof of pur-
chase or original date receipt. A return authorization number can be obtained by calling
(719) 591-6950 and must accompany all returns to manufacturer. Please include a note
explaining the problem when returning the product.
Made in China
K&H Pet Products, Central Garden & Pet
Colorado Springs, CO
www.khpet.com
(719) 591-6950
c
Important Safeguards
K&H Limited Two Year Warranty
d
REV2_03- 1 7-20