K&H Rectangle Booster Pet Seat Assembly/Installation Instructions

K&H Rectangle Booster Pet Seat
Assembly & Installation Instructions
Thank you for purchasing the Rectangle Booster Pet Seat by K&H Pet Products. This product was
designed to elevate your pet for a better view while riding in the car and can help keep pets in place while
operating a motor vehicle. When used properly, your Rectangle Booster Pet Seat will last for many years to come.
ASSEMBLY INSTRUCTIONS:
Lay all parts of your Rectangle Booster Pet Seat out on a table. You should
1
have a fabric cover, a 3 inch soft cushion with removable cover, 4 white
foam pieces, and 4 white corner reinforcement stickers. See FIGURE 1.
Use this diagram in FIGURE 1 to identify each foam piece. The two foam
pieces A in this diagram will form the two sloped side walls of the pet seat.
Foam piece B in the diagram will form the back wall, and the "U" shaped
foam piece C will form the front of the pet seat.
Start by connecting one of the side walls (foam piece A) to the back wall
2
(foam piece B). Note: Make sure the edge with the single notch on the side
wall of A is facing down. See FIGURE 2.
Next connect the second side wall (foam piece A) to the other side of the
3
back wall (foam piece B). The single notch on the side wall of A should be
facing down. See FIGURE 3.
Finish closing the walls of the pet seat frame by connecting the front wall
4
(foam piece C, the "U" shaped piece), to both side walls A. Locate the
white corner reinforcement stickers and attach one of the stickers to one of
the connecting edges. Overlap the sticker over the corner and press to ad-
here. See FIGURE 4. Add a corner reinforcement sticker to the remaining
3 corners of the pet seat's foam frame.
Lay out the fabric cover and separate the seat's attached fleece interior sec-
5
tion from its attached bottom section. Lay the fleece section to the side and
place the foam frame into the bottom section of the other side. Pull the outer
edges of the fabric cover over the bottom half of the foam frame. See FIG-
URE 5. NOTE: The "U" shaped foam piece C is the front of the pet seat. It
needs to face the fleece section of the cover before the cover is installed.
Take the attached fleece section of the cover and lay it inside the foam
6
frame. Pull the outer edges of the cover over the top half of the foam frame
working your way around to the other side. See FIGURE 6.
Make any final adjustments to the cover then zip the cover together. See
7
FIGURE 7. Place the pillow inside the booster seat and it's now ready to
be installed into your vehicle.
VEHICLE INSTALLATION INSTRUCTIONS
CARE INSTRUCTIONS:
Remove pillow cover and machine wash on cold then line dry.
To wash outer pet seat cover, unzip, remove all interior
foam pieces, and machine wash then line dry.
ON BACK:
OVER
K&H Pet Products with design is a registered trademark of K&H Manufacturing, LLC.
©2022 Central Garden & Pet Company
K&H Pet Products, Central Garden & Pet
B
C
White Corner
Reinforcement Stickers
Figure 1
B
A
Notch Facing Down
Figure 2
A
A
C
White Corner
Reinforcement Sticker
Figure 4
Figure 6
K&H Limited One Year Warranty
Our warranty is as follows: K&H Pet Products warrants to the original consumer, that this
product will be free of defects and workmanship for a period of one year from the date of
purchase. The manufacturer's liability hereunder is limited to replacement of the product. This
warranty is void if the product has been damaged by accident, unreasonable use, neglect,
tampering, or other causes not arising from defects in material and workmanship.
To exercise your warranty: If, during the warranty period, your product malfunctions,
return it to the place of purchase with your original purchase receipt. If this cannot be
done, return the product, postage prepaid, to K&H Pet Products, with a dated proof of pur-
chase or original date receipt. A return authorization number can be obtained by calling
(719) 591-6950 and must accompany all returns to manufacturer. Please include a note
explaining the problem when returning the product.
Made in China
Colorado Springs, CO
www.khpet.com l (719) 591-6950
A
A
B
A
A
Notch Facing Down
Figure 3
C
Figure 5
Figure 7
REV0_02- 1 7-22