curt 13035 Manual

13035
7/31/2020
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH:
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT DISTRIBUTION HITCH:
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT
Parts List
ITEM QTY PART NUMBER
1 1 1_2 FISHWIRE 1/2" FISHWIRE
2 8 20-00103 NUT,SER-FLANGE,7/16-14 UNC,GRD8,YZ
3 2 10-10414 HHCS,M10x1.5,45,CL10.9,YZ
4 2 30-00184 WASHER,LOCK,7/16,YZ
5 2 30-00166 WASHER,FLAT,7/16,YZ
6 2 20-00062 NUT, SER-FLANGE,1/2-13 UNC,GRD8,YZ
7
2 CM-SP1 .250 x 1.50 x 2.00" SQUARE HOLE SPACER
8 2 10-10272 BOLT,CAR,1/2-13 UNC,1-3/4,GRD8,YZ
9 8 10-10281 BOLT,CAR,7/16-14 UNC,1-1/4,GRD8,YZ
USE ACCESS SLOT
TO PLACE FASTENER
FOR VEHICLES WITHOUT
WELDNUT IN PLACE
HITCH WEIGHT: 39 LBS.
INSTALL TIME
45
PROFESSIONAL: MINUTES
NOVICE (DIY): 90 MINUTES
INSTALL NOTES:
- NO DRILLING REQUIRED
- REMOVE BUMPER
BRACKET BOLTS
INSTALLATION STEPS
1) Remove bumper bracket bolts and set aside for later install directions.
2) Position end plate between bumper bracket and frame. Align the holes of the bumper bracket with the
holes of the hitch and loosely reinstall factory bolts.
3) Early models: Using 1/2" carriage bolts and square hole spacers provided, pass one of each through
the large hole in frame under the bumper bracket into the hole in the end plate.
Late models : With weldnut at furthest hole, from rear bumper, in frame install 10mm bolt with 7/16"
lockwasher and flatwasher.
4) Position receiver cross-tube assembly between the end plates. Install 7/16" bolts in end plates and tighten
with 7/16" hex flange nuts.
5) First: Torque 7/16" fasteners to 70 lb-ft.
Then: Torque all remaining 10mm bolts to 45 lb-ft., 1/2" bolts to 110 lb-ft.
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of
this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or
consequential loss or damage.
RRH13035
85-05 CHEVY/GMC ASTRO & SAFARI
DESCRIPTION
8
7
6
9
4,000 LBS. TRAILER WEIGHT &
6,000 LBS. TRAILER WEIGHT &
1-877-287-8634
EXISTING WELDNUT
(IN SOME MODELS)
FACTORY BOLTS
EXISTING WELDNUTS
1
2
EXCEPT 16" SPARE
400 LBS. TONGUE WEIGHT.
LBS. TONGUE WEIGHT
600
5
4
3