1. Manuals
  2. Brands
  3. Reboot Manuals
  4. Welding System
  5. RBM1300
  6. Operation manual

Reboot RBM1300 Operation Manual

Hide thumbs

Advertisement

Table of Contents

Reboot RBM1300
insulated gate bipolar transistor (IGBT) power module, which can change work frequency to medium frequency so as
to replace the traditional Transistor transformer with the medium frequency transformer. its characterized with
portable, small size, light weight, low consumption and etc. It is also an intelligent and easy-to-operate multi-function
welding machine with MMA, MIG GAS, MIG GASLESS and LIFT TIG. It has the characteristics of strong welding
performance and diversified usage scenarios. It can be used in both gas and gasless conditions, and the welding
effect is excellent. It is highly praised by welding enthusiasts. It is also very friendly to beginners in welding and can
quickly get started.
Part 1: Machine Introduction
1. Current display meter
The digital Ammeter is used to display the actual output current of the power source.
It is also used to display Parameters in Programming Mode.
Depending on the Programming Parameter selected, the status indictor adjacent to the Ammeter will illuminate to show the units
of the programming parameter.
When welding, the Ammeter will display actual welding current.
2. Voltage display meter
3. MIG/MMA/LIFT TIG Function selection
4. Choose the wire diameter and the choice of gas welding and gasless welding
5. Small range voltage adjustment and inductance adjustment
It is recommended that the voltage does not need to be adjusted. The machine is a unified machine. The voltage, current and
wire feeding speed are automatically matched. Only when the deviation is too large, it can be adjusted appropriately. Inductance
adjustment: If the splash is too large or the welding pool is not deep enough, it can be adjusted to a larger value, otherwise it can
be smaller.
Operation Manual
welding machines adopts the latest pulse width modulation (PWM) technology and
1
Version Number: RBM1300-20210109A1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RBM1300 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Reboot RBM1300

Summary of Contents for Reboot RBM1300

  • Page 1 Version Number: RBM1300-20210109A1 Operation Manual Reboot RBM1300 welding machines adopts the latest pulse width modulation (PWM) technology and insulated gate bipolar transistor (IGBT) power module, which can change work frequency to medium frequency so as to replace the traditional Transistor transformer with the medium frequency transformer. its characterized with portable, small size, light weight, low consumption and etc.
  • Page 2 Version Number: RBM1300-20210109A1 6. Adjust the value knob Clockwise rotate to enlarge the current, and anti-clockwise rotate to reduce the current. 7. MIG Welding torch connector 8. Polarity selection plug In MMA and LIFT TIG state, this plug does not need to be connected; in MIG gas welding state, this plug is connected to positive terminal 8;...
  • Page 3 Version Number: RBM1300-20210109A1 Hose clamp Used to fix the trachea to prevent air leakage. Conductive Spare parts, need to be replaced frequently, tip0.8 please keep inventory. Conductive Spare parts, need to be replaced frequently, tip1.0 please keep inventory. For flux-cored welding wire,Spare parts need...
  • Page 4 It is a qualified product. Precautions for power-on inspection: 1、 Please make sure your power supply voltage is 220+-15%. REBOOT RBM1300 just supports 220V input voltage in North America and Japan, UK, EU and other regions; if you have a generator power supply, please ensure that the generator is not less than 4000w.

  • Page 5: Part 4: Technical Specifications

    Version Number: RBM1300-20210109A1 3. The power plug is loose. 4. The internal circuit is loose (due to long-distance transportation, bumps), you need to open the cover and check the internal connection line. Part 4: Technical specifications TYPE RBM1300 Input power voltage (V) 1phase AC220V，50/60Hz...
  • Page 6 3、To adjust the current, only the current can be adjusted. Note: 1) The welding rod specification supported by reboot RBM1300 is below 3.2(1/8in), usually 2.5(3/32in) and 3.2(1/8in). European style generally uses E6013, American style generally uses E7018, and stainless steel generally uses ER308.

  • Page 7: Mig Mode

    1、 Select “MIG ” process. 2、 Set polarity for MIG Solid wire（gas） Reboot RBM1300 Excellent support for welding wires of 0.8mm and 1.0mm in diameter, and automatically and intelligently match the best welding parameters according to different specifications of welding wires to achieve the...
  • Page 8 Version Number: RBM1300-20210109A1 3、Connect MIG gun and ground clamp. 4、Install wire spool 0.030”(0.8mm)/0.040”(1.0mm)diameter 4”(100mm 1kg)wire spool...
  • Page 9 Version Number: RBM1300-20210109A1 5、Set drive roll Face the side marked 0.030” away from the machine. Remarks: 1. There are two grooves on one wire feed wheel, one side is 0.030” (0.8mm) and the other side is 0.040” (1.0mm) to match the corresponding wire diameter.
  • Page 10 Version Number: RBM1300-20210109A1 8、Please connect CO2 gas： 1. Attach gas hose to machine. 2. Attach hose and regulator to gas bottle. 9、Remove consumables and depress trigger until wire comes out. Replace consumables. Press and hold the torch switch wrench for more than 3 seconds to not weld. This is fast wire feeding. Let the welding wire be quickly delivered to the gun head.
  • Page 11 Version Number: RBM1300-20210109A1 11、With contact tip 1/4” from metal, depress trigger completely to initiate arc. 12、To replace the welding wire. Use the cutting pliers to cut off the front section of the contact tip that is more than the welding wire, loosen the wire feed mechanism pinch wheel, rotate the welding wire reel clockwise, turn the welding wire back to the wire feed reel, pay attention to pinch the welding wire with your right hand to avoid the wire bounce.
  • Page 12 1, Select “MIG” process. 2、Set polarity for MIG flux-cored(gasless). Reboot RBM1300 outstandingly supports 0.8mm and 1.0 mm diameter welding wires, and automatically and intelligently matches the best welding parameters according to different specifications of welding wires to achieve the best results.

  • Page 13: Install Wire Spool

    Version Number: RBM1300-20210109A1 4、Connect MIG gun and ground clamp. Flux-cored wire Note: No need to use gas cylinder and gas meter 5、Install wire spool. 0.030”(0.8mm)/0.040”(1.0mm)diameter, 4”(100mm 1kg)wire spool. 5、Set drive roll. Face the side marked 0.030” away from the machine.
  • Page 14 Version Number: RBM1300-20210109A1 2. Gear wire feed wheel, gear wire feed wheel is suitable for flux-cored welding wire, our standard configuration has 1 piece of 1kg flux-cored welding wire, which can be directly installed and used. 6、Feed wire and set pressure.
  • Page 15 Version Number: RBM1300-20210109A1 8、Remove consumables and depress trigger until wire comes out, Replace consumables. Press and hold the torch switch wrench for more than 3 seconds to not weld. This is fast wire feeding. Let the welding wire be quickly delivered to the gun head.
  • Page 16 Version Number: RBM1300-20210109A1 1.Choose MIG, MMA, LIFT-TIG working mode. 2.Choose welding wire diameter 0.8mm/1.0mm, choose airless (Flux-cored wire). 3. The machine has a unified function, so just adjust this knob the the welding current, voltage and wire feeding speed are adjusted automatically at the same time.

  • Page 17: Lift-Tig Mode

    6) If you have any questions, please contact us at service@mirthtek.com. 3、LIFT-TIG mode: REBOOT RBM1300 for thin plates with higher welding process requirements or welding with higher process requirements, especially for stainless steel welding, you can use the LIFT TIG mode, which requires the use of pure argon.
  • Page 18 Version Number: RBM1300-20210109A1 Remark: TIG welding gun is not included in the package, you need to purchase it separately. 3、 Adjust the current, only the current can be adjusted. 4、 WP17V Structure of welding torch...
  • Page 19 Version Number: RBM1300-20210109A1 Note: Standard accessories package kit not included this tig torch. Remark: 1. ceramic nozzel, 2 .tungsten collet, 3. tungsten collet body, 4 .short back cap, 5. long back cap. The above structure is a wearing part, please keep it in stock.

  • Page 20: Part 7:Troubleshooting

    Version Number: RBM1300-20210109A1 1. 7 imported transistors, stable and powerful current output. 2. 3 high-power large capacitors, the machine is more stable. 3. Cooling fans, greatly improving the machine load duration. 4. The main transformer of all copper, the power is larger.
  • Page 21 Version Number: RBM1300-20210109A1 Observe all Safety Guidelines detailed throughout this manual PROBLEMS POSSIBLE (SYMPTOMS) CAUSE OUTPUT PROBLEMS “Do not Plug in machine or turn it on”. Major physical or electrical damage is evident. Contact your local Authorized Field Service Facility.
  • Page 22 Version Number: RBM1300-20210109A1 RMB1300 machine welding parameters Shielding Material Thickness-220V Polarity Wire Material Wire Type Settings 24 Ga. 20 Ga. 18 Ga. 16 Ga. 20-30 Setting Size 0.6mm 0.9mm 1.2mm 1.6mm SCFH Wire speed 0.025" Voltage 14.5 0.6mm Inductance Wire speed 0.030"...

Table of Contents