Download Print this page

Advertisement

Quick Links

Reboot RBM-1550 welding machines adopts the latest pulse width modulation (PWM) technology and insulated
gate bipolar transistor (IGBT) power module, which can change work frequency to medium frequency so as to
replace the traditional Transistor transformer with the medium frequency transformer. its characterized with portable,
small size, light weight, low consumption and etc. It is also an intelligent and easy-to-operate multi-function welding
machine with MMA, MIG GAS, MIG GASLESS and LIFT TIG. It has the characteristics of strong welding
performance and diversified usage scenarios. It can be used in both gas and gasless conditions, and the welding
effect is excellent. It is highly praised by welding enthusiasts. It is also very friendly to beginners in welding and can
quickly get started.
Part 1: Machine Introduction
Positive Terminal. Welding current flows from the power source via heavy duty bayonet type terminals. It
is essential, however,that the male plug is inserted and turned securely to achieve a sound electrical
connection.
12.
Polarity conversion socket.
13.
Negative terminal
Welding current flows from the power source via heavy duty bayonet type terminals. It is essential,
however, that the male plug is inserted and turned securely to achieve a sound electrical connection。
14.
Polarity slection plug
In MMA and LIFT TIG state, this plug does not need to be connected; in MIG gas welding state, this plug
is connected to positive terminal 11; in MIG airless welding state, this plug is connected to negative
terminal 13.
Operation Manual
1.
2.
3. 220V, voltage input indicator light.
4. 110V, voltage input indicator light.
5. Fault light, overheating and overcurrent protection
light.
6. Spool gun and MIG gun switch
7. Small range voltage adjustment
8.
9.
10.
11.
1
Version Number: RBM1550-20210414A1
MIG/MMA/LIFT TIG function selection.
Current display meter.
Digital ammeter is used to display preset current and
actual output current.
It is recommended that the voltage does not need to
Be adjusted. The machine is a unified machine. The
voltage, current and wire feeding speed are
automatically matched. Only when the deviation is
too large, it can be adjusted
appropriately.
Adjust the current and wire feed speed knob
Turn clockwise to increase the current, turn
counterclockwise to decrease the current.
MIG welding torch connector
Spool gun control socket
Positive terminal

Advertisement

loading
Need help?

Need help?

Do you have a question about the RBM-1550 and is the answer not in the manual?

Questions and answers

Summary of Contents for Reboot RBM-1550

  • Page 1 Version Number: RBM1550-20210414A1 Operation Manual Reboot RBM-1550 welding machines adopts the latest pulse width modulation (PWM) technology and insulated gate bipolar transistor (IGBT) power module, which can change work frequency to medium frequency so as to replace the traditional Transistor transformer with the medium frequency transformer. its characterized with portable, small size, light weight, low consumption and etc.
  • Page 2 Part 2: Introduction to the product and configuration list Picture Name Remark Please check outside of the whole machine no RBM-1550 scratch and break , it can power on normally. MB15 3M, MB 15 MIG welding torch, European central welding plug.
  • Page 3 Part 3: Simple test for powering on the machine Reboot RBM-1550 Welding machines will be subjected to strict various tests when they leave the factory to ensure that each welding machine that reaches the user is of high quality, because our machine has to go through tens of thousands of kilometers of long-distance transportation from the factory to the delivery to you.
  • Page 4: Part 4: Technical Specifications

    Version Number: RBM1550-20210414A1 2) In order to reduce the working temperature of the machine, it is normal for the fan to continue to rotate for a few seconds after the power is turned off. 3) During high-strength continuous welding, machine protection may occur. After continuous heat dissipation, the machine will return to normal, which is normal.
  • Page 5 3 To adjust the current, Knob “A” only the current can be adjusted. Note: 1) The welding rod specification supported by reboot RBM1600 is below 4.0(5/32in), usually 2.5(3/32in) and 3.2(1/8in). European style generally uses E6013, American style generally uses E7018, and stainless...
  • Page 6: Mig Mode

    MIG mode Reboot RBM-1550 provides two welding modes: gas shielded welding and self-shielded welding with fluxed wire. If you are working at home or in a studio, in order to ensure a better welding effect, it is recommended that you use the gas welding mode;...
  • Page 7 Version Number: RBM1550-20210414A1 2. Use mixed gas protection (usually a mixture of argon and carbon dioxide) Connect MIG gun and ground clamp.
  • Page 8 Version Number: RBM1550-20210414A1 Install wire spool 0.030”(0.8mm)/0.040”(1.0mm)diameter 4”(100mm 1kg)wire spool Set drive roll...
  • Page 9 Version Number: RBM1550-20210414A1 Face the side marked 0.030” away from the machine. Remarks: 1. There are two grooves on one wire feed wheel, one side is 0.030” (0.8mm) and the other side is 0.040” (1.0mm) to match the corresponding wire diameter. 2.
  • Page 10 Version Number: RBM1550-20210414A1 Please refer to the digital sign on the rear panel of the machine for the input voltage, the wrong voltage will damage the machine. RBM1550 only has 230V voltage input, RBM1550D supports 110V or 220V voltage input. 1.8 Please connect CO2 gas:...
  • Page 11 Version Number: RBM1550-20210414A1 consumables. 1.11 Adjust wire feed speed, current and voltage. 1. Select MIG, SPOOL GUN working status. 2. Function selection. 3. Choose the wire diameter of 0.8 and choose solid wire pure CO2 welding, Or choose 0.8mm welding wire and mixed gas.
  • Page 12 Version Number: RBM1550-20210414A1 Use the cutting pliers to cut off the front section of the contact tip that is more than the welding wire, loosen the wire feed mechanism pinch wheel, rotate the welding wire reel clockwise, turn the welding wire back to the wire feed reel, pay attention to pinch the welding wire with your right hand to avoid the wire bounce.
  • Page 13 Version Number: RBM1550-20210414A1 Note: 1. Nozzle, 2. Conductive nozzle. They are wearing parts and need to be replaced frequently, please keep inventory. 19. The guide wire tube, it is best to equip a spare part because it may damage the accessories.
  • Page 14 2.1 Select “MIG ” process.。 2.2 Set polarity for MIG Flux-cored(gasless) Reboot RBM-1550 outstandingly supports 1.0 mm diameter welding wires, and automatically and intelligently matches the best welding parameters according to different specifications of welding wires to achieve the best results.
  • Page 15 Version Number: RBM1550-20210414A1 2.4 Install wire spool 0.030”(0.8mm)/0.040”(1.0mm)diameter 4”(100mm 1kg)wire spool 2.5 Set drive roll Face the side marked 0.030” away from the machine Remarks: 1. There are two grooves on one wire feed wheel, one side is 0.030” (0.8mm) and the other side is 0.040”...
  • Page 16 Version Number: RBM1550-20210414A1 2.7 Connect to Input Power Please refer to the digital sign on the rear panel of the machine for the input voltage, the wrong voltage will damage the machine. RBM1550 only has 230V voltage input, RBM1550D supports 110V or 220V voltage input.
  • Page 17 Version Number: RBM1550-20210414A1 2.9 Installation of welding torch. The welding wire should be extended outside the European central socket, and then install the welding torch. The wire guide tube and contact tip of the welding torch need to match the welding wire. Press and hold the torch switch wrench for more than 3 seconds to not weld.
  • Page 18 Version Number: RBM1550-20210414A1 2.12 Adjust wire feed speed, current and voltage. 1. Select MIG, SPOOL GUN working status. 2. Function selection. 3. Choose the wire diameter of 1.0 and choose flux wire. 4. The machine is a unified machine, adjust this knob, current, voltage and wire feeding speed are adjusted at the same time, and automatically match.
  • Page 19 Version Number: RBM1550-20210414A1 2.15 Structure of welding gun Note: 1. Nozzle, 2. Conductive nozzle. They are wearing parts and need to be replaced frequently, please keep inventory. 19. The guide wire tube, it is best to equip a spare part because it may damage the accessories.
  • Page 20 Version Number: RBM1550-20210414A1 C) Spool gun mode 1. Select “SPOOL GUN ” process. 2. Solid wire welding: panel setting, polarity conversion wire and ground wire connection please follow point “A”above. flux cored wire welding: panel setting, polarity conversion wire and ground wire connection please follow point “B”...
  • Page 21: Lift-Tig Mode

    2. For the installation of the wire feed roller, please see the mark "2'" in the picture 5.3 LIFT-TIG mode Reboot RBM-1550 for thin plates with higher welding process requirements or welding with higher process requirements, especially for stainless steel welding, you can use the LIFT TIG mode, which requires...
  • Page 22 Version Number: RBM1550-20210414A1 1. Select “Lift TIG ” process. 2. How to connect.
  • Page 23 Version Number: RBM1550-20210414A1 Remark: TIG welding gun is not included in the package, you need to purchase it separately. 3. Adjust the current, only the current can be adjusted.
  • Page 24 Version Number: RBM1550-20210414A1 4. WP17V Structure of welding torch Note: Standard accessories package kit not included this tig torch. Remark: 1. ceramic nozzel, 2 .tungsten collet, 3. tungsten collet body, 4 .short back cap, 5. long back cap. The above structure is a wearing part, please keep it in stock. Note:...
  • Page 25: Part 7:Troubleshooting

    Version Number: RBM1550-20210414A1 Part 7:Troubleshooting Observe all Safety Guidelines detailed throughout this manual...
  • Page 26 Version Number: RBM1550-20210414A1 PROBLEMS POSSIBLE (SYMPTOMS) CAUSE OUTPUT PROBLEMS “Do not Plug in machine or turn it on”. Major physical or electrical damage is evident. Contact your local Authorized Field Service Facility. 1. Make sure correct voltage is applied to the machine. No wire feed, weld output or gas flow when gun trigger is pulled.
  • Page 27 Version Number: RBM1550-20210414A1 Wire speed 0.025" Voltage 17.5 17.5 0.6mm Inductance Wire speed C100 0.030" DCEP Voltage 16.5 17.5 17.5 16.5 17.5 17.5 100% CO2 0.8mm Inductance Wire speed 0.040" Voltage 17.5 18.5 17.5 18.5 1.0mm Inductance Wire speed 0.030" Voltage 13.5 14.5...

This manual is also suitable for:

Rbm-1500