Table of Contents
Advertisement
@
) CHECK INSTALLATION
DIMENSIONS
A: Disposer Height
B: Distance from bottom of sink
bowl to centerline of discharge
outlet. (Add 1/2" when stainless
steel sink is used.)
C: Distance from centerline of
the discharge outlet to end
of discharge tube.
D: Disposer Width
E: Distance from disposer vertical
centerline to centerline of
P-trap connection.
B
i
,',,--I__I
F: Centerline of disposer discharge to centerline at waste pipe entering wall
(Dimension "F" must be greater than 1/4" to prevent standing water in disposer.)
i
f replacing an existing disposer, skip ahead to Instruction 6.
I
If this is a first time installation, continue with Instruction
2.
I
O
DISCONNECT
SINK DRAIN
1. Loosen nut (A) at top of "P-trap" with pipe wrench (see Figure 2-1).
2. Loosen nut (B) at top of extension pipe. Remove extension pipe.
3. Loosen nut (C) at base of sink flange. (If nut is corroded or too tight, apply
penetrating lubricant,)
4. Push sink flange up through sink hole and remove it (see Figure 2-2).
5. Clean sink flange area of any putty or other debris.
O
DISASSEMBLE
NEW DISPOSER
MOUNTING
ASSEMBLY
1. insert wrenchette (or screwdriver) into one mounting lug and hold lower mount-
ing ring securely with one hand (see Figure 3-1). With your other hand, turn
mounting assembly counterclockwise
to remove mounting assembly from lower
mounting ring.
2, Turn mounting assembly over (see Figure 3-2) and loosen three mounting
screws (A) until you can access snap ring (B).
3. Use screwdriver to pry snap ring off of sink flange.
Mounting assembly will
now come apart.
O
INSTALL
FLANGE
IN SINK HOLE
1. Roll 1/4 pound (4 oz.) of non-hardening
plumber's putty to make 3/4" thick rope
to seal around sink flange.
2. Apply putty evenly around sink hole (see Figure 4-1).
3. Press sink flange slowly but firmly into sink drain hole to seat evenly on putty
(see Figure 4-2). Use screwdriver or putty knife to scrape all putty from edge
of sink hole.
Model
A
B
C
D
E
601016012
11 3/8"
6"
4'
6 5/16"
5"
6011/6013
12 5/8"
6"
4"
6 5/16"
5'
60552
12 5/80
6"
4"
7 1/4"
5_
60581/60554
12 3/4"
6 11/16 =
4"
8 1/2"
6 3/4 m
60691/60556
12 3/4 = 6 1t/16 m 4"
8 1/2"
5 3/4'
60559*
15 7/8 =
9 7/16"
4"
7 1/2"
5 3/4'
60571/60562
12 5/8'
6"
4 =
7 1/4"
5"
60572/60563
12 5/8"
6"
4'
7 1/4=
5"
60793
12 3/4"
6 11/16 = 4"
8 1/4"
5 3/4"
• Indicates Batch Feed Model
9
"P-Trap"
2-1
/
2-2
4-1
O
ATTACH UPPER
MOUNTING
ASSEMBLYTO
SINK FLANGE
You may wish to place a weighted object in the sink to hold the sink flange in place. (Place a towel
under object in sink to prevent scratching.) Reference Figure 5-1 for part identification.
1. Working from under sink, slip fiber gasket and
4. Tighten three mounting screws up to sink
metal backup ring over sink flange.
2. Holding fiber gasket and backup ring in place,
slip mounting ring over sink flange so it seats
against backup ring.
3. With fiber gasket, backup ring, and mounting
ring tight to sink bottom, slide snap ring onto
sink flange until it pops into groove on flange*.
until mounting assembly is seated tightly
and evenly against sink.
* Placing a thick, wide rubber band around
the sink flange (above the snap ring
groove) may help hold parts in place while
installing snap ring. (Remember to remove
rubber band after snap ring is installed.)
4-2
-
O--
SinkFlange
FiberGasket _
O
BackupRing --
_)
MountingRing __
Screws(3)_
BiB
SnapRing --
O
I
f you are replacing an existing disposer, go to Instruction 6. If this is a first time installation,
skip ahead to Instruction
7.
5-1
Hide quick links:
Advertisement
Table of Contents
