Related Manuals for Lantronix BOLERO40 Series
Summary of Contents for Lantronix BOLERO40 Series
- Page 1 BOLERO40 Series Hardware Manual Part Number PMD-00012 Revision E March 2025 Version: 1.0.3; Modified: Monday, March 17, 2025...
-
Page 2: Intellectual Property
Technical Support Online: https://www.lantronix.com/technical-support Sales Offices For a current list of our domestic and international sales offices, go to the Lantronix web site at https://www.lantronix.com/about-us/contact Disclaimer All information contained herein is provided “AS IS.” Lantronix undertakes no obligation to update the information in this publication. -
Page 3: Revision History
(Python License). Lantronix grants you no right to receive source code to the Open Source software; however, in some cases, rights and access to source code for certain Open Source software may be available directly from Lantronix’ licensors. Your use of each Open Source component or software is subject to the terms of the applicable license. -
Page 4: Table Of Contents
2.11 Non-ionizing radiation ................... 13 Safety Standards ..................14 Technical Data ................... 15 Product specifications .................... 15 4.1.1 Power consumption for BOLERO40 Series ..............16 4.1.2 Operating temperatures ....................17 GSM/2G/3G engine specifications ................. 18 4.2.1 GNSS engine specifications ................... 18 BOLERO40 Series Application Interface ............. - Page 5 Appendix ....................32 Considerations when using BOLERO40 Series ............32 NMEA data message ....................32 GPRS Coding scheme ..................... 33 Cellular Bands and Frequencies for BOLERO40 Series Devices ......33 Compliance ......................35 9.5.1 UK Declaration of Conformity ..................35 9.5.2...
- Page 6 Table 13. Lantronix output messages ....................33 Table 14. Coding schemes and maximum data rates over air interface ........... 33 Table 15. Cellular Bands and Frequencies for BOLERO40 Series Devices ......... 34 Table 16. EU Statements ........................42 BOLERO40 Series Hardware Manual...
-
Page 7: Introduction
2G, LTE-M1 and 3G models. It is designed to operate with internal GSM/GNSS antennas allowing fast and easy installation. This device supports the new firmware version 3.0.0 and higher. The BOLERO40 series comes with a 10-wire harness with a 10-pin connector at the cable’s end. -
Page 8: Circuit Concept And System Architecture
1: Introduction Circuit concept and System architecture The architecture of the BOLERO40 Series consists of the following major components: Figure 1. BOLERO40 Series block diagram The principle of system operation is very simple. In each system is installed one of BOLERO40 series device, which consists of: •... -
Page 9: Labelling
1: Introduction • Weight: 210 gr / cardboard box • Packaging insert and quick setup guide Figure 3. BOLERO40 series standard box contents Labelling Font label of BOLERO40 Series Back label of BOLERO40 Series BOLERO40 Series Hardware Manual... -
Page 10: Related Documents
[10] AppNote_1-Wire_Guide.pdf Contains information how to use the 1-Wire interface on the BOLERO40 series devices. These PDF files are viewable and printable from Adobe Reader. If you do not have the Adobe Reader installed, you can download it from http://www.adobe.com. -
Page 11: Security
Also, when using your BOLERO40 while driving, please pay full attention to driving, pull off the road and park before making or answering a call if driving conditions so require. When applications are prepared for mobile use, they should fulfil road-safety instructions of the current law! BOLERO40 Series Hardware Manual... -
Page 12: Electronic Devices
Children Do not allow children to play with your BOLERO40 series devices. It is not a toy. Children could hurt themselves or others (by poking themselves or others in the eye with the antenna, for example). -
Page 13: Non-Ionizing Radiation
2.11 Non-ionizing radiation The BOLERO40 Series comes with internal LTE/GSM/GNSS antennas. Therefore, care should be taken to install the devices/antennas in such a position that no part of the human body will normally rest within 20 cm of any part of the antennas/casing for more than a few minutes whilst the equipment is in use. -
Page 14: Safety Standards
3: Safety Standards 3 Safety Standards The devices of the LTE/GSM/GNSS BOLERO40 Series comply with all applicable RF safety standards. BOLERO40 meet the safety standards for RF receivers and the standards and recommendations for the protection of public exposure to RF electromagnetic energy established by government bodies and professional organizations, such as directives of the European Community, Directorate General V in matters of radio frequency electromagnetic energy. -
Page 15: Technical Data
INTERNAL MEMORY 16 Mbyte Flash for configuration, data-logging and firmware storage NMEA Msg.: GLL, GGA, RMC, VTG, GSV, GSA SUPPORTED PROTOCOLS Lantronix Msg.: IOP, GSM, AREA, 3DP, BIN - see documents [1]. Internal antennas GSM/2G/3G/GNSS ANTENNA Table 2. Product specifications... -
Page 16: Power Consumption For Bolero40 Series
4: Technical Data 4.1.1 Power consumption for BOLERO40 Series These measurements are performed with the firmware version 3.1.0_rc8. All measurements performed under T = 23°C, V =12 VDC; BOLERO45: 2G: 1800 MHz Avr. power consum. @12 VDC Modes Comments Unit In a transmit burst the current Max. -
Page 17: Operating Temperatures
4.1.2 Operating temperatures Parameter Min. Typ. Max. Unit Operating temperature °C Storage temperature (Bolero41 and °C Bolero45 Storage temperature (Bolero43) °C * Storage capacity should be 40% ~ 50% full charge capacity. Table 7. Operating temperature BOLERO40 Series Hardware Manual... -
Page 18: Gsm/2G/3G Engine Specifications
Tracking: -164 dBm Cold start: -148 dBm SENSITIVITY Velocity: 500 m/s (972 knots) OPERATIONAL LIMITS Altitude: 50,000 m Max. update rate: 1 Hz. Online / Offline / Autonomous A-GPS SUPPORT Crystal Oscillator OSCILLATOR Table 9. GNSS engine specifications BOLERO40 Series Hardware Manual... -
Page 19: Bolero40 Series Application Interface
5: BOLERO40 Series Application Interface 5 BOLERO40 Series Application Interface Power supply The power supply for the BOLERO40 series devices must be a single voltage source of: = +10.8 V...+48.0 VDC DC IN The operating voltage (V ) must be applied permanently to the BOLERO40 series devices and DC IN able to provide sufficient current of up to 2 A (pulse). -
Page 20: Determining The External Equipment Type
Determining the External Equipment Type Before you connect the serial port pins of the BOLERO40 series devices to external equipment, you need to determine if the external hardware serial ports are configured as DTE (Data Terminal Equipment) or DCE (Data Communications Equipment). -
Page 21: Hardware Interfaces
PC. V24, ±12 VDC (Serial 0) Serial port (transmit data) for 8-BLACK direct connection to the host PC. 9-ORANGE CAN L CAN-Low CAN-BUS <1.5 V 10-WHITE CAN-H CAN-High CAN-BUS >3.5 V Table 11. 10-wire harness/connector description BOLERO40 Series Hardware Manual... -
Page 22: Special Io Description
Analogue inputs can be connected to temperature sensors (e.g., NTC resistor as shown in Figure or other sensor as shown in Figure 6. Figure 5 shows a fixed resistor and a variable resistor (Negative Temperature Coefficient - whose resistance or capacitance decreases when BOLERO40 Series Hardware Manual... -
Page 23: Figure 5. Connection Example 1 When Using It As Analogue Input
6). Both circuit examples (the NTC diagram above and the sensor below) are only illustrations to show the aim of these IOs when using them as analogue inputs. Figure 6. Connection example 2 when using it as analogue input BOLERO40 Series Hardware Manual... -
Page 24: How To Use Ios As Digital Inputs
(e.g., $PFAL,Cnf.Set,AL0=IO.e8=redge:IO5.Set=cyclic,1000,2000). Note: The power should not be applied directly to the IOs configured as outputs without having a resistor between them. BOLERO40 Series Hardware Manual... -
Page 25: Serial Port 0 - Serial Communication Signals (Rtd And Txd)
A 1-Wire bus uses only one wire for signaling and power. Up to four 1-Wire devices can be connected to the 1-wire interface of the BOLERO40 at the same time. The information received from 1-Wire sensors can then be sent to the remote TCP server using PFAL commands/scripts. BOLERO40 Series Hardware Manual... -
Page 26: Inserting A Sim Card Into The Sim Holder
4. Push the card into the slot until it clicks into place. 5. (Re)Connect the battery harness to the to the 3-pin white connector on the PCB. 6. Finally, replace the half part of the casing and screw the 4 x TORX#8 screws with your screwdriver. BOLERO40 Series Hardware Manual... -
Page 27: Entering Pin Of Sim Card
To enter the PIN of the SIM card, follow the steps below (refer to Figure 14): 1. Read the information in section 6.1.2 about the serial port of the BOLERO40 Series. 2. Install the Lantronix Workbench software. 3. Connect your BOLERO40 to a free PC COM port using your own cable and power up your device. -
Page 28: Led Indicators
(not included) or cable ties (not included). For more detailed information how to install BOLERO40 devices and what should be considered during the installation, refer to the application note [AppNotes_AVL_Installation_Guide.pdf]. BOLERO40 Series Hardware Manual... -
Page 29: Figure 14. Device Mounting Types
6: Hardware Interfaces Figure 14. Device mounting types BOLERO40 Series Hardware Manual... -
Page 30: Housing
7: Housing 7 Housing The necessary dimensions for mounting the housing can be found in the drawing below. Figure 15. BOLERO40 housing BOLERO40 Series Hardware Manual... -
Page 31: Rf Exposures
• Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. BOLERO40 Series Hardware Manual... -
Page 32: Appendix
Table 12 below lists the NMEA and Lantronix supported protocols and gives a brief description for each of them. For further description about these protocols, refer to the related documents These protocols can be sent via SMS, TCP, data call, serial port, e-mail or stored inside the device... -
Page 33: Gprs Coding Scheme
Cellular Bands and Frequencies for BOLERO40 Series Devices The table below lists the bands, and their corresponding frequencies used by BOLERO40 series devices for different cellular networks. Cellular Bands... -
Page 34: Table 15. Cellular Bands And Frequencies For Bolero40 Series Devices
9: Appendix Cellular Bands Frequency 2G BAND3 TX: 1710~1785 MHz; RX: 1805~1880 MHz 2G BAND5 TX: 824~849MHz; RX: 869~894 MHz 2G BAND8 TX: 880~915MHz; RX: 925~960 MHz Table 15. Cellular Bands and Frequencies for BOLERO40 Series Devices BOLERO40 Series Hardware Manual... -
Page 35: Compliance
9: Appendix Compliance 9.5.1 UK Declaration of Conformity Figure 16. UK Declaration of Conformity BOLERO40 Series Hardware Manual... -
Page 36: Eu Declaration Of Conformity
9: Appendix 9.5.2 EU Declaration of Conformity Figure 17. EU Declaration of Conformity BOLERO40 Series Hardware Manual... -
Page 37: Eu Statements
EU-meddelelse om begrænsninger i brug: Denne enhed er kun begrænset til indendørs brug. Det betjenes måske ikke udendørs. Deutsch Hiermit erklärt Lantronix, Inc., dass sich das Gerät BOLERO43 device in [German] Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 2014/53/EUbefindet. - Page 38 EU Notice of Restrictions on Use: This device is limited to indoor use only. It may not be operated outdoors. Español Por medio de la presente Lantronix, Inc. declara que el BOLERO43 [Spanish] device module cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 2014/53/EU.
- Page 39 Il ne doit pas être utilisé àl'extérieur Icelandic Hér með lýsir Lantronix, Inc. því yfir að BOLERO43 device sé í samræmi við grunnkröfur og önnur viðeigandi ákvæði tilskipunar 2014/53 / ESB. Í heildartexta ESB-samræmisyfirlýsingarinnar er að finna á eftirfarandi internetfangi: https://www.lantronix.com/products/bolero40-series/...
- Page 40 EU értesítés a korlátozásokról: Ez az eszköz csak beltéri használatra korlátozódik. Lehet, hogy szabadban nem üzemeltethető. Norwegian Lantronix, Inc. erklærer herved at denne BOLERO43 device er i samsvar med de grunnleggende kravene og andre relevante bestemmelser i direktiv 2014/53 / EU.
- Page 41 9: Appendix Code Language Statement Polski [Polish] Niniejszym Lantronix, Inc. oświadcza, że BOLERO43 device jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 2014/53/EU. Pełny tekst deklaracji zgodności EU jest dostępny pod następującym adresem internetowym: https://www.lantronix.com/products/bolero40-series/ Zawiadomienie UE o ograniczeniach użytkowania: To urządzenie jest przeznaczone wyłącznie do użytku w pomieszczeniach.
-
Page 42: Table 16. Eu Statements
9: Appendix Code Language Statement Slovensko Lantronix, Inc. izjavlja, da je ta FOX4-4G device v skladu z bistvenimi [Slovenian] zahtevami in ostalimi relevantnimi določili direktive 2014/53/EU. Celotno besedilo izjave EU o skladnosti je na voljo na naslednjem spletnem naslovu: https://www.lantronix.com/products/bolero40-...
Need help?
Do you have a question about the BOLERO40 Series and is the answer not in the manual?
Questions and answers