Subscribe to Our Youtube Channel
Related Manuals for PITH & STEM DropTop Duo 27Light
Summary of Contents for PITH & STEM DropTop Duo 27Light
- Page 1 DropTop™Duo 27Light Assembly & Installation Instructions Page: 1 © 2024 Pith & Stem Ltd. All rights reserved.
-
Page 2: Before You Begin
DropTop™Duo 27Light Assembly & Installation Guidelines Please read and follow these instructions carefully to ensure the correct assembly and installation of your DropTop™ wall-mounted desk. Failure to adhere to the instructions may result in product damage, personal injury, or voiding of the product warranty. Before You Begin: •... - Page 3 DropTop™ Duo 27 Light Fixings Pack x7 +1 Extra +1 Extra + 2 Extra +1 Extra Plasterboard Wall Brick/Concrete Wall Fixings Fixings Tools *Not included *included *Not included For a Plasterboard Wall 25mm hole saw or a 25mm Spade bit Page: 3...
- Page 4 DropTop™ Duo 27 Light Parts Page: 4...
- Page 5 DropTop™ Duo 27 Light dimensions Exterior dimensions when Closed: 1 4 c Height: 71cm Width: 143cm 1 4 1 Depth: 15.8cm 1 0 c Worktop Dimensions: Width: 143 cm Depth: 58.5 cm The Duo 27 Light supports up to 50kg in weight 1 0 c Weight - 37kg To safely mount your...
- Page 6 DropTop™ Duo 27 Light Monitor space dimensions The Duo 27Light is designed to house dual 27-inch monitors. 1 3 7 Available Monitor Space dimensions: 1 0 c Height: 41 cm 4 1 c Width: 137 cm Depth: Please see note below* Note that the monitor space depth varies with your chosen Monitor Mount...
- Page 7 Monitor Mounts. Your DropTop™ Light will include one of the following monitor brackets, depending on your order configuration. Extendable Arm Mount Slim Mount Depth: 5cm Depth: 1.3cm The recommended The recommended maximum depth maximum depth for your monitor is 8cm for your monitor is 5cm Tilt Mount Depth: 3.3cm...
- Page 8 DropTop™ Duo 27 Light Wall Plate dimensions. 2 cm 3 . 7 c 15.7 cm Page: 8...
- Page 9 DropTop™ Duo 27 Light Cable Management The Duo 27 Light is designed with a back recess depth of 1.6cm. This allows for any cables to be fed tidily behind the DropTop 1 . 6 It is recommended to feed the monitor's power cable through round cable management grommet 5 .
- Page 10 DropTop™ Duo 27 Light Assembly Fixings Pack #2 Front. Back. Incorrect. Correct. Fixings Pack #3 Fixings Pack #1 Ensure that part F is correctly oriented before assembly, as shown. Page: 10...
- Page 11 Front View Back View Fixings Pack #3 Fixings Pack #1 At this step, make sure to position Part B at the front view instead of the back, as shown above. Page: 11...
- Page 12 Fixings Pack #2 Page: 12...
-
Page 13: Back View
Lay part H down flat, Fixings Pack #3 then place the Fixings Pack #2 assembled component from Step 7 on top, aligning it with the hinge recesses. Fixings Pack #2 Fixings Pack #5-3 Back View Page: 13... - Page 14 Fixings Pack #7 Fixings Pack #7 Fixings Pack #7 Fixings Pack #6 Fixings Pack #7 Fully extend the soft opening stays by pulling on each end. Spheres must point inwards Page: 14...
- Page 15 Fixings Pack #4 Fixings Pack #4 Page: 15...
- Page 16 Oval Cable management Round Cable management grommet. grommet. 1. Push out the 1. Place the two central section of slender metal the circular cable discs into the grommet. You'll use it later. black oval ring, aligning them correctly. 2. Slot the assembled cable 2.
- Page 17 Matching colour cover cap stickers have been provided with your DropTop™ Place the provided colour-matched cover cap stickers over any exposed screws for a clean finish. Page: 17...
- Page 18 To install your monitor on a Slim or Tilt mount. Your DropTop™ comes with either a Slim Monitor Mount or a Tilt Monitor Mount, depending on your chosen configuration. This way up. This way up. Slim Monitor Mount Tilt Monitor Mount Fix the VESA plate to the monitor with the supplied screws.
- Page 19 Attach your selected cable to the monitor and pass it through the oval- shaped cable grommet on panel E. Feed the power cable through the cable management cutout. Place the monitors face down on the worktop. Feed the power cable through the round cable After cabling, reattach the central grommet at the back of panel B and plug it into section to the round cable grommet.
- Page 20 Back View Secure the monitor from the front. At the back, insert and lightly screw the bolts to keep it in Place your monitor into the DropTop™ monitor position. Fine-tune the height as needed, then space, ensuring cables are properly routed fully tighten the bolts to firmly secure the through.
- Page 21 To install your monitor on an Extendable Arm Mount f- M4 ×12Bolt a -Wall Plate & b-VESA Plate(1) c-Wrench(1) Articulating Arms(1) This way up. This way up. Flat Back Monitor. d-Bolt(2) f- M4 ×12Bolt l-Cable Tie(3) Attach the VESA Plat-b to your monitors using the provided screws.
- Page 22 Fully extend the articulating arms out. Front View Wall Plate & Articulating Arms-A Back View 2 x M6 Bolt Incorrect Correct Attach the Wall Plate & Articulating Arms-A to the VESA slot on the back of the DropTop, using the 2 x M6 bolts provided.
- Page 23 Attach your selected cable to the monitor and pass it through the oval- shaped cable grommet on panel E. Feed the power cable through the cable management cutout. Place the monitor face down on the worktop. After cabling, reattach the central Feed the power cable through the round cable section to the round cable grommet.
- Page 24 2 x M4 Bolt - Secure the VESA Plate-b to the articulating arm using the 2x M4 Bolt- d provided. Use the wrench provided to adjust the tilting angle of the Hook the VESA Plate-b to the Socket on VESA Plate-b. the fully extended arms.
- Page 25 The mount brackets should be positioned as Place your monitor into the DropTop™ monitor indicated in the diagram to ensure proper and space, ensuring cables are properly routed mounting of the monitors. through. Page: 25...
-
Page 26: Mounting The Wall Plate
Mounting the Wall plate. Wall plate Height 53 cm Worktop Height Your preferred desk height Back View Floor While securing the monitor from the front, Your DropTop™ desk can be installed at any slightly loosen the screws at the back and adjust height that best suits your needs and preferences. - Page 27 DropTop™ Duo 27 Light Wall plate height 53 cm 10cm The height to install the wall plate should be If you plan to mount the DropTop above an measured from the top of the desired desk item, ensure there is 10 cm of clearance height to the top of the recessed area of the wall from the base of the DropTop™.
- Page 28 Installing on a brick and concrete wall. WALL 53cm Use the wall plate as a guide and mark the position of the fixing holes with a pencil. The height to install the wall plate should be measured from the top of the desired desk Drill 8 x 8mm sized holes at a depth of 90mm (9cm).
- Page 29 WALL WALL Fixings Pack To safely mount the desk, ensure that the DropTop™ is locked before lifting it onto the wall plate. The DropTop™ should fit snugly in the recess of the wall plate. Page: 29...
- Page 30 Installing on Plasterboard/Drywall. *Not included Recommended tools 25mm hole saw or a 25mm Spade bit 53cm Use the wall plate as a guide and mark the position of the fixing holes with a pencil. Using a hole saw, cut 3 holes of 25mm diameter The height to install the wall plate should be centred on the top row of your wall plate pencil measured from the top of the desired desk...
- Page 31 GeeFix Fixings Assemble your GeeFix wall anchor system by threading the supplied pullcord through the round wall plug, the curved back plate, and back through the wall plug. While holding onto the pullcord, feed the curved back plate into the hole and centre on the 25mm hole.
- Page 32 WALL To safely mount the desk, ensure that the DropTop™ is locked before lifting it onto the wall plate. The DropTop™ should fit snugly in the recess of the wall plate. Page: 32...
- Page 33 DropTop™Duo 27 Light Thank you for choosing to purchase your DropTop™ wall-mounted desk. We are delighted to have you as part of our community. You're taking a wonderful step towards improving your workspace and achieving a better work-life balance. We couldn't be more thrilled to support you in this journey.
Need help?
Do you have a question about the DropTop Duo 27Light and is the answer not in the manual?
Questions and answers