Siemens SIPART PS2 Hardware Installation Instructions
Electropneumatic positioners mounting kit on samson actuator
Hide thumbs
Also See for SIPART PS2:
- Diagnostic manual (592 pages) ,
- Operating instructions manual (372 pages) ,
- Compact operating instructions (294 pages)
Related Manuals for Siemens SIPART PS2
Summary of Contents for Siemens SIPART PS2
- Page 1 Mounting Dimension drawings SIPART PS2 Electropneumatic positioners Mounting kit 6DR4004-8S on Samson actuator Compact Hardware Installation Instructions 6DR4004-8S 09/2021 A5E50679668A-AA...
-
Page 2: Qualified Personnel
Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems. -
Page 3: Table Of Contents
Table of contents Mounting ............................... 5 Mounting introduction......................5 Mounting, schematic representation ..................9 Scope of delivery and procedure ..................10 Dimension drawings ..........................15 Mounting kit 6DR4004-8S on Samson actuator Compact Hardware Installation Instructions, 09/2021, A5E50679668A-AA... - Page 4 Table of contents Mounting kit 6DR4004-8S on Samson actuator Compact Hardware Installation Instructions, 09/2021, A5E50679668A-AA...
-
Page 5: Mounting
Mounting Mounting introduction The compact mounting instructions are intended for persons who mechanically mount the device and apply specifically to the 6DR4004-8S mounting kit. WARNING Safety instructions Before starting work on the positioner, refer to the description in the positioner operating instructions: •... - Page 6 Mounting 1.1 Mounting introduction • Variant 1: Actuator spring closes without covering the spring chamber Mounting kit 6DR4004-8S on Samson actuator Compact Hardware Installation Instructions, 09/2021, A5E50679668A-AA...
- Page 7 Mounting 1.1 Mounting introduction • Variant 2: Actuator spring closes with covering of the spring chamber Mounting kit 6DR4004-8S on Samson actuator Compact Hardware Installation Instructions, 09/2021, A5E50679668A-AA...
- Page 8 Mounting 1.1 Mounting introduction • Variant 3: Actuator spring opens with covering of the spring chamber Mounting kit 6DR4004-8S on Samson actuator Compact Hardware Installation Instructions, 09/2021, A5E50679668A-AA...
-
Page 9: Mounting, Schematic Representation
Mounting 1.2 Mounting, schematic representation Mounting, schematic representation Mounting kit 6DR4004-8S on Samson actuator Compact Hardware Installation Instructions, 09/2021, A5E50679668A-AA... -
Page 10: Scope Of Delivery And Procedure
Mounting 1.3 Scope of delivery and procedure Scope of delivery and procedure Serial Quan‐ Designation Note tity Terminal block Mounting plate for mechanical and pneumatic connection of positioner and actuator bell housing Shaft screw M4x21.5 Guides the pulley with the carrier pin and rotates the lever arm. - Page 11 Mounting 1.3 Scope of delivery and procedure Serial Quan‐ Designation Note tity Clamping piece Mounting shaft screws on the actuator spindle Carrier pin Mounting with pulley (5) on lever (6) Role Mounting with carrier pin (4) on lever (6) Lever Banjo bolt 3/8 Mounting of the terminal block to the bell housing Hexagon bolt...
- Page 12 Mounting 1.3 Scope of delivery and procedure Procedure The legend letters correspond to the numbers in the table of the scope of delivery. The legend letters have the following meaning: Exhaust air connection Exhaust air opening Actuating pressure Y1 Mounting kit 6DR4004-8S on Samson actuator Compact Hardware Installation Instructions, 09/2021, A5E50679668A-AA...
- Page 13 Mounting 1.3 Scope of delivery and procedure 1. If the positioner is attached to an actuator: Disassemble the positioner, the rear cover plate and the clamping piece on the spindle. ⑤ ⑬ ④ 2. Insert the pulley and spring onto the carrier pin ④...
- Page 14 Mounting 1.3 Scope of delivery and procedure 8. The following applies to variants 1 and 2: Remove the screw from (B) and from (C). The following applies to variant 3: Remove the screw from (B). 9. Screw the shaft screws (20) in the front and (21) on the right into the bell housing. Place the ⑳...
-
Page 15: Dimension Drawings
Dimension drawings Figure 2-1 Dimension drawing, dimensions in mm (inch) Mounting kit 6DR4004-8S on Samson actuator Compact Hardware Installation Instructions, 09/2021, A5E50679668A-AA... - Page 16 Dimension drawings Mounting kit 6DR4004-8S on Samson actuator Compact Hardware Installation Instructions, 09/2021, A5E50679668A-AA...
Need help?
Do you have a question about the SIPART PS2 and is the answer not in the manual?
Questions and answers