Subscribe to Our Youtube Channel
Related Manuals for Miller OptX CLWH-100
Summary of Contents for Miller OptX CLWH-100
- Page 1 2024-0 Processes Laser Welding Description OWNER’S MANUAL For product information, Owner’s Manual translations, and more, visit www.MillerWelds.com...
-
Page 2: Table Of Contents
Table of Contents 1. Introduction................3 2. -
Page 3: Introduction
• Use by skilled persons as per your Hazard and Risk Analysis only (see Clause 4 [▶3] ‘Hazard & Risk Assessment’) • Designed to be used for laser welding with Miller OptX series system only. • When used with Miller OptX series system, the OptX Helmet must be worn with laser protective safety eyewear underneath the helmet as delineated below. -
Page 4: Field Of Application And Intended Use
Miller OptX system. All users of the OptX Helmet should be trained in both welding and laser safety and must follow all instructions and safety warnings, safety labels on the OptX system and helmet, and all applicable safety standards, laws and regulations. -
Page 5: Troubleshooting
Step 2. Adjust headgear top bands (1) for proper depth on the head to ensure correct balance and stability. Step 3. Push in the adjusting knob (2) located on the back of the headgear and turn left or right to desired tightness. -
Page 6: Cleaning
▼Table 1. Troubleshooting (Continued) Item Problem Solution Headgear is not pivoting smoothly • Pivot components are likely not seated together properly, and thus misaligned. • Fore-aft linear or rotational adjustment notches may not be seated fully or are interfering with base of pivots, and should be fixed accordingly. -
Page 7: Helmet Assembly Drawings
▼Table 2. Component Lifespan (Continued) Component MTBF [≥ hours] Carbon Fiber Shell 5000 Lens Frame 20000 Headgear 2000 Helmet Assembly Drawings Place lenses into Lens Frame in order, as shown in figure below: Figure 2. Laser Welding Helmet Assembly Drawing ④... -
Page 8: Markings And Standards Applied
Figure 3. Laser Welding Helmet Lens Clamp Installation LEAD-IN DIRECTION SEE NOTES CLIP ACTUATION *REAR ISO VIEW DETAIL A NOTES: 1. Lead clamp frame into side pocket as show in Figure 3 [▶ 2. Rotate clip counterclockwise and push frame downward until clip clicks into opposite side pocket. Markings and Standards Applied The OptX helmet is certified in accordance with PPE Regulation (EU) 2016/425 of the European Parliament and of the Council of 9 March 2016. -
Page 9: Manufacturing Month And Lot Number
Manufacturing Month and Lot Number • for the interior left side wall of the helmet PDXXXXXX: Miller internal Production Order, where XXXXXX is a 6-digit number suffix. OXCH11230025: Helmet serial number OXCH [MM] [YY] [nnnn], where nnnn is a sequential 4-digit number. -
Page 10: Disposal
Service and Support For questions regarding the safety, set-up, operation and maintenance of the OptX Helmet please contact the manufacturer, importer or your responsible Miller subsidiary. Product Returns For information regarding returns of the OptX Helmet locate your nearest distributor or service agency. Call 1- 800-4-A-Miller, or visit us at www.MillerWelds.com... - Page 11 Effective January 1, 2024 (Equipment with a serial number preface of NE or newer) This limited warranty supersedes all previous Miller warranties and is exclusive with no other guarantees or warranties expressed or implied. • RFCS Foot Controls (Except RFCS-RJ45)
-
Page 12: Annex A: Example Of A Hazard & Risk Assessment
Annex A: Example of a Hazard & Risk Assessment The following shows an example of the typical Hazard & Risk Assessment only considering the Miller OptX laser source. It does not substitute to comprehensive Hazard & Risk Assessment comprising the complete working place and working procedures. -
Page 13: Annex B: Product Specifications
350 x 250 x 210 mm (13.78 x 9.84 x 8.27 inch) Material (Helmet shell) Carbon Fiber Standards ANSI ISEA Z87.1-2020 and CSA Z94.3 DIN EN 379, DIN EN 175 DIN EN 169, DIN EN 207 Warranty See Miller True Blue Error and Technical Changes Reserved OM-296985A | 4/15/24...
Need help?
Do you have a question about the OptX CLWH-100 and is the answer not in the manual?
Questions and answers