Hyundai S2F21 AC500 Manual

Copy OEM Logo Here (→)
Electronic Installation Instructions
If this is a printed copy of the installation instructions, ensure you have the latest revision by
scanning the QR code or by entering the website address listed below before beginning installation.
Use the latest revision date as noted by "Rev. Date" above.
Entered by MPA
www.hyundaiaccessories.com/admin_media_uploads/installationSheets/s2f21_ac500.pdf
Improperly installed Crossbars may increase windnoise in the vehicle cabin.
NOTICE:
To avoid, ensure that the Crossbars are installed in the correct position, per this instruction.
Instructional Symbols / Definitions
Denotes warnings that may lead to
serious physical injury or vehicle damage
Denotes cautions to be taken to avoid
physical injury or electronic component
damage
Denotes cautions to be taken to avoid
vehicle and component damage
Basic Required Tools
Clean Water Clean Cloth
Part Weight (Gross) FMVSS 110 Compliance Information
10.57 All dealers must determine if the Net weight they have added in the form of all options or accessories, when added to the weight of all Port/Dealer Installed
lbs
options or accessories, exceeds the lesser of 1.5% of GVWR or 100 lbs. If the additional weight does exceed the lesser of the indicated thresholds, a "Load
Carrying Capacity Reduced" label must be installed. A black, fine-point, indelible marker must be used to write by hand onto the label, the reduced carrying
4.79
kg
capacity in kilograms or pounds, which is the total weight of all added options and accessories.
Load Label Part Number: NP070 - 09003
REGULARLY CHECK THE TIGHTNESS BY PERFORMING A TUG ON CROSSBARS.
THEY SHOULD NOT MOVE. If crossbars move, see step 5 & 6 for proper tightening. Incorrect clamp tightness can cause crossbar separation from vehicle resulting in
product failure and vehicle damage. Serious physical injury may occur.
Loads must be evenly distributed and secured.
Any weight carried on the vehicle on the vehicle will adversely affect its handling particularly in cornering or in a cross wind and the vehicle should therefore be driven with increased
caution.
Only use NON-STRETCH tie down straps. Use of stretch elastic tie downs may cause loss of load, potential serious injury, and vehicle damage.
Notes to the installer:
1) Read the entire Installation Instructions prior to beginning the installation of the part.
2) If applicable, scan the barcode label located on the accessory part or packaging prior to installing, to register the part. If this accessory is installed as a replacement, register the removal of
the old part before registering the new part. Old and new parts will have different barcode data, and the old registration cannot be reused.
3) Make sure the vehicle is completely clean and dry in the area(s) the part is to be installed.
4) Ensure the vehicle is properly protected in the area(s) that the accessory is to be installed.
5) NEVER place tools on painted surfaces, seating surfaces, dash pad, console or floor carpet/mats.
6) Always wear appropriate personal protective equipment, including gloves, safety glasses, etc., when required.
Genuine Accessories
Vehicle Model: Santa Fe
Model Year 2019~
Part No. S2F21 AC500
Language English
Rev. Date 12/16/2022
Denotes quality processes to be checked
prior to moving to the next step
Denotes specific tools that are necessary
to complete a step
N
O
Denotes important information to be
reviewed during the step
T
E
Step Ladder Torque Wrench
Revision Date
12/16/2022
Accessory: Crossbars
Difficulty: ( A )
Note: Difficulty stated above reflects the minimum level of
expertise required to install the accessory:
(A) Customer
(B) Dealer Technician
(C) Master Technician or Specialist
Denotes personal protective equipment (PPEs) that may
be required for a step. Examples of safety equipment
icons noted below:
Glasses
Mask
5mm Hex Socket
Gloves
Hearing Protection
Page 1 of 9